| Message ID | 1406748032-19417-1-git-send-email-nm@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 07/30/2014 02:20 PM, Nishanth Menon wrote: > GPIO modules are also interrupt sources. However, they require both the > GPIO number and IRQ type to function properly. > > By declaring that GPIO uses interrupt-cells=<1>, we essentially do not > allow users of the nodes to use the interrupt property appropritely. > > With this change, the following now works: > > interrupt-parent = <&gpio6>; > interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > > Fixes: 6e58b8f1daaf ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board') > Signed-off-by: Nishanth Menon <nm@ti.com> > --- > Based on v3.16-rc7 > > arch/arm/boot/dts/dra7.dtsi | 16 ++++++++-------- > 1 file changed, 8 insertions(+), 8 deletions(-) Tony, Gentle ping. we still have this issue on 3.17-rc1. any suggestions on if we can pick this up during RC? > > diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi > index 8012763..f21ef39 100644 > --- a/arch/arm/boot/dts/dra7.dtsi > +++ b/arch/arm/boot/dts/dra7.dtsi > @@ -172,7 +172,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio2: gpio@48055000 { > @@ -183,7 +183,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio3: gpio@48057000 { > @@ -194,7 +194,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio4: gpio@48059000 { > @@ -205,7 +205,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio5: gpio@4805b000 { > @@ -216,7 +216,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio6: gpio@4805d000 { > @@ -227,7 +227,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio7: gpio@48051000 { > @@ -238,7 +238,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > gpio8: gpio@48053000 { > @@ -249,7 +249,7 @@ > gpio-controller; > #gpio-cells = <2>; > interrupt-controller; > - #interrupt-cells = <1>; > + #interrupt-cells = <2>; > }; > > uart1: serial@4806a000 { >
* Nishanth Menon <nm@ti.com> [140818 11:49]: > On 07/30/2014 02:20 PM, Nishanth Menon wrote: > > GPIO modules are also interrupt sources. However, they require both the > > GPIO number and IRQ type to function properly. > > > > By declaring that GPIO uses interrupt-cells=<1>, we essentially do not > > allow users of the nodes to use the interrupt property appropritely. > > > > With this change, the following now works: > > > > interrupt-parent = <&gpio6>; > > interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > > > > Fixes: 6e58b8f1daaf ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board') > > Signed-off-by: Nishanth Menon <nm@ti.com> > > --- > > Based on v3.16-rc7 > > > > arch/arm/boot/dts/dra7.dtsi | 16 ++++++++-------- > > 1 file changed, 8 insertions(+), 8 deletions(-) > > Tony, > Gentle ping. we still have this issue on 3.17-rc1. any suggestions on > if we can pick this up during RC? Yes thanks applying into omap-for-v3.17/fixes. Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 8012763..f21ef39 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -172,7 +172,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio2: gpio@48055000 { @@ -183,7 +183,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio3: gpio@48057000 { @@ -194,7 +194,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio4: gpio@48059000 { @@ -205,7 +205,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio5: gpio@4805b000 { @@ -216,7 +216,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio6: gpio@4805d000 { @@ -227,7 +227,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio7: gpio@48051000 { @@ -238,7 +238,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio8: gpio@48053000 { @@ -249,7 +249,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; uart1: serial@4806a000 {
GPIO modules are also interrupt sources. However, they require both the GPIO number and IRQ type to function properly. By declaring that GPIO uses interrupt-cells=<1>, we essentially do not allow users of the nodes to use the interrupt property appropritely. With this change, the following now works: interrupt-parent = <&gpio6>; interrupts = <5 IRQ_TYPE_LEVEL_LOW>; Fixes: 6e58b8f1daaf ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board') Signed-off-by: Nishanth Menon <nm@ti.com> --- Based on v3.16-rc7 arch/arm/boot/dts/dra7.dtsi | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)