@@ -200,6 +200,24 @@ config SERIAL_KS8695_CONSOLE
receives all kernel messages and warnings and which allows
logins in single user mode).
+config SERIAL_MESON
+ tristate "Meson serial port support"
+ depends on ARCH_MESON
+ select SERIAL_CORE
+ help
+ This enables the driver for the on-chip UARTs of the Amlogic
+ MesonX processors.
+
+config SERIAL_MESON_CONSOLE
+ bool "Support for console on meson"
+ depends on SERIAL_MESON=y
+ select SERIAL_CORE_CONSOLE
+ help
+ Say Y here if you wish to use a Amlogic MesonX UART as the
+ system console (the system console is the device which
+ receives all kernel messages and warnings and which allows
+ logins in single user mode) as /dev/ttyAMLx.
+
config SERIAL_CLPS711X
tristate "CLPS711X serial port support"
depends on ARCH_CLPS711X || COMPILE_TEST
@@ -48,6 +48,7 @@ obj-$(CONFIG_SERIAL_MPC52xx) += mpc52xx_uart.o
obj-$(CONFIG_SERIAL_ICOM) += icom.o
obj-$(CONFIG_SERIAL_M32R_SIO) += m32r_sio.o
obj-$(CONFIG_SERIAL_MPSC) += mpsc.o
+obj-$(CONFIG_SERIAL_MESON) += meson_uart.o
obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
new file mode 100644
@@ -0,0 +1,634 @@
+/*
+ * Based on meson_uart.c, by AMLOGIC, INC.
+ *
+ * Copyright (C) 2014 Carlo Caione <carlo@caione.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+/* Register offsets */
+#define AML_UART_WFIFO 0x00
+#define AML_UART_RFIFO 0x04
+#define AML_UART_CONTROL 0x08
+#define AML_UART_STATUS 0x0c
+#define AML_UART_MISC 0x10
+#define AML_UART_REG5 0x14
+
+/* AML_UART_CONTROL bits */
+#define AML_UART_TX_EN BIT(12)
+#define AML_UART_RX_EN BIT(13)
+#define AML_UART_TX_RST BIT(22)
+#define AML_UART_RX_RST BIT(23)
+#define AML_UART_CLR_ERR BIT(24)
+#define AML_UART_RX_INT_EN BIT(27)
+#define AML_UART_TX_INT_EN BIT(28)
+#define AML_UART_DATA_LEN_MASK (0x03 << 20)
+#define AML_UART_DATA_LEN_8BIT (0x00 << 20)
+#define AML_UART_DATA_LEN_7BIT (0x01 << 20)
+#define AML_UART_DATA_LEN_6BIT (0x02 << 20)
+#define AML_UART_DATA_LEN_5BIT (0x03 << 20)
+
+/* AML_UART_STATUS bits */
+#define AML_UART_PARITY_ERR BIT(16)
+#define AML_UART_FRAME_ERR BIT(17)
+#define AML_UART_TX_FIFO_WERR BIT(18)
+#define AML_UART_RX_EMPTY BIT(20)
+#define AML_UART_TX_FULL BIT(21)
+#define AML_UART_TX_EMPTY BIT(22)
+#define AML_UART_ERR (AML_UART_PARITY_ERR | \
+ AML_UART_FRAME_ERR | \
+ AML_UART_TX_FIFO_WERR)
+
+/* AML_UART_CONTROL bits */
+#define AML_UART_TWO_WIRE_EN BIT(15)
+#define AML_UART_PARITY_TYPE BIT(18)
+#define AML_UART_PARITY_EN BIT(19)
+#define AML_UART_CLEAR_ERR BIT(24)
+#define AML_UART_STOP_BIN_LEN_MASK (0x03 << 16)
+#define AML_UART_STOP_BIN_1SB (0x00 << 16)
+#define AML_UART_STOP_BIN_2SB (0x01 << 16)
+
+/* AML_UART_MISC bits */
+#define AML_UART_XMIT_IRQ(c) (((c) & 0xff) << 8)
+#define AML_UART_RECV_IRQ(c) ((c) & 0xff)
+
+/* AML_UART_REG5 bits */
+#define AML_UART_BAUD_MASK 0x7fffff
+#define AML_UART_BAUD_USE BIT(23)
+
+#define AML_UART_PORT_NUM 6
+#define AML_UART_DEV_NAME "ttyAML"
+
+
+static struct uart_driver meson_uart_driver;
+
+static struct uart_port *meson_ports[AML_UART_PORT_NUM];
+
+static void meson_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int meson_uart_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS;
+}
+
+static unsigned int meson_uart_tx_empty(struct uart_port *port)
+{
+ u32 val;
+
+ val = readl(port->membase + AML_UART_STATUS);
+ return (val & AML_UART_TX_EMPTY) ? TIOCSER_TEMT : 0;
+}
+
+static void meson_uart_stop_tx(struct uart_port *port)
+{
+ u32 val;
+
+ val = readl(port->membase + AML_UART_CONTROL);
+ val &= ~AML_UART_TX_EN;
+ writel(val, port->membase + AML_UART_CONTROL);
+}
+
+static void meson_uart_stop_rx(struct uart_port *port)
+{
+ u32 val;
+
+ val = readl(port->membase + AML_UART_CONTROL);
+ val &= ~AML_UART_RX_EN;
+ writel(val, port->membase + AML_UART_CONTROL);
+}
+
+static void meson_uart_shutdown(struct uart_port *port)
+{
+ unsigned long flags;
+ u32 val;
+
+ free_irq(port->irq, port);
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ val = readl(port->membase + AML_UART_CONTROL);
+ val &= ~(AML_UART_RX_EN | AML_UART_TX_EN);
+ val &= ~(AML_UART_RX_INT_EN | AML_UART_TX_INT_EN);
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void meson_uart_start_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+ unsigned int ch;
+
+ if (uart_tx_stopped(port)) {
+ meson_uart_stop_tx(port);
+ return;
+ }
+
+ while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL)) {
+ if (port->x_char) {
+ writel(port->x_char, port->membase + AML_UART_WFIFO);
+ port->icount.tx++;
+ port->x_char = 0;
+ continue;
+ }
+
+ if (uart_circ_empty(xmit))
+ break;
+
+ ch = xmit->buf[xmit->tail];
+ writel(ch, port->membase + AML_UART_WFIFO);
+ xmit->tail = (xmit->tail+1) & (SERIAL_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+}
+
+static void meson_receive_chars(struct uart_port *port)
+{
+ struct tty_port *tport = &port->state->port;
+ char flag;
+ u32 status, ch, mode;
+
+ do {
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+ status = readl(port->membase + AML_UART_STATUS);
+
+ if (status & AML_UART_ERR) {
+ if (status & AML_UART_TX_FIFO_WERR)
+ port->icount.overrun++;
+ else if (status & AML_UART_FRAME_ERR)
+ port->icount.frame++;
+ else if (status & AML_UART_PARITY_ERR)
+ port->icount.frame++;
+
+ mode = readl(port->membase + AML_UART_CONTROL);
+ mode |= AML_UART_CLEAR_ERR;
+ writel(mode, port->membase + AML_UART_CONTROL);
+
+ /* It doesn't clear to 0 automatically */
+ mode &= ~AML_UART_CLEAR_ERR;
+ writel(mode, port->membase + AML_UART_CONTROL);
+
+ status &= port->read_status_mask;
+ if (status & AML_UART_FRAME_ERR)
+ flag = TTY_FRAME;
+ else if (status & AML_UART_PARITY_ERR)
+ flag = TTY_PARITY;
+ }
+
+ ch = readl(port->membase + AML_UART_RFIFO);
+ ch &= 0xff;
+
+ if ((status & port->ignore_status_mask) == 0)
+ tty_insert_flip_char(tport, ch, flag);
+
+ if (status & AML_UART_TX_FIFO_WERR)
+ tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+
+ } while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_RX_EMPTY));
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tport);
+ spin_lock(&port->lock);
+}
+
+static irqreturn_t meson_uart_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port = (struct uart_port *)dev_id;
+
+ spin_lock(&port->lock);
+
+ if (!(readl(port->membase + AML_UART_STATUS) & AML_UART_RX_EMPTY))
+ meson_receive_chars(port);
+
+ if (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL))
+ meson_uart_start_tx(port);
+
+ spin_unlock(&port->lock);
+
+ return IRQ_HANDLED;
+}
+
+static const char *meson_uart_type(struct uart_port *port)
+{
+ return (port->type == PORT_MESON) ? "meson_uart" : NULL;
+}
+
+static int meson_uart_startup(struct uart_port *port)
+{
+ u32 val;
+ int ret = 0;
+
+ val = readl(port->membase + AML_UART_CONTROL);
+ val |= (AML_UART_RX_RST | AML_UART_TX_RST | AML_UART_CLR_ERR);
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ val &= ~(AML_UART_RX_RST | AML_UART_TX_RST | AML_UART_CLR_ERR);
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ val |= (AML_UART_RX_EN | AML_UART_TX_EN);
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ val |= (AML_UART_RX_INT_EN | AML_UART_TX_INT_EN);
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ val = (AML_UART_RECV_IRQ(1) | AML_UART_XMIT_IRQ(port->fifosize / 2));
+ writel(val, port->membase + AML_UART_MISC);
+
+ ret = request_irq(port->irq, meson_uart_interrupt, 0,
+ meson_uart_type(port), port);
+
+ return ret;
+}
+
+static void meson_uart_change_speed(struct uart_port *port, unsigned long baud)
+{
+ u32 val;
+
+ while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_EMPTY))
+ cpu_relax();
+
+ val = readl(port->membase + AML_UART_REG5);
+ val &= ~AML_UART_BAUD_MASK;
+ val = ((port->uartclk * 10 / (baud * 4) + 5) / 10) - 1;
+ val |= AML_UART_BAUD_USE;
+ writel(val, port->membase + AML_UART_REG5);
+}
+
+static void meson_uart_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned int cflags, iflags, baud;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ cflags = termios->c_cflag;
+ iflags = termios->c_iflag;
+
+ val = readl(port->membase + AML_UART_CONTROL);
+
+ val &= ~AML_UART_DATA_LEN_MASK;
+ switch (cflags & CSIZE) {
+ case CS8:
+ val |= AML_UART_DATA_LEN_8BIT;
+ break;
+ case CS7:
+ val |= AML_UART_DATA_LEN_7BIT;
+ break;
+ case CS6:
+ val |= AML_UART_DATA_LEN_6BIT;
+ break;
+ case CS5:
+ val |= AML_UART_DATA_LEN_5BIT;
+ break;
+ }
+
+ if (cflags & PARENB)
+ val |= AML_UART_PARITY_EN;
+ else
+ val &= ~AML_UART_PARITY_EN;
+
+ if (cflags & PARODD)
+ val |= AML_UART_PARITY_TYPE;
+ else
+ val &= ~AML_UART_PARITY_TYPE;
+
+ val &= ~AML_UART_STOP_BIN_LEN_MASK;
+ if (cflags & CSTOPB)
+ val |= AML_UART_STOP_BIN_2SB;
+ else
+ val &= ~AML_UART_STOP_BIN_1SB;
+
+ if (cflags & CRTSCTS)
+ val &= ~AML_UART_TWO_WIRE_EN;
+ else
+ val |= AML_UART_TWO_WIRE_EN;
+
+ writel(val, port->membase + AML_UART_CONTROL);
+
+ baud = uart_get_baud_rate(port, termios, old, 9600, 115200);
+ meson_uart_change_speed(port, baud);
+
+ port->read_status_mask = AML_UART_TX_FIFO_WERR;
+ if (iflags & INPCK)
+ port->read_status_mask |= AML_UART_PARITY_ERR |
+ AML_UART_FRAME_ERR;
+
+ port->ignore_status_mask = 0;
+ if (iflags & IGNPAR)
+ port->ignore_status_mask |= AML_UART_PARITY_ERR |
+ AML_UART_FRAME_ERR;
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int meson_uart_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ int ret = 0;
+
+ if (port->type != PORT_MESON)
+ ret = -EINVAL;
+ if (port->irq != ser->irq)
+ ret = -EINVAL;
+ if (ser->baud_base < 9600)
+ ret = -EINVAL;
+ return ret;
+}
+
+static void meson_uart_release_port(struct uart_port *port)
+{
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
+}
+
+static int meson_uart_request_port(struct uart_port *port)
+{
+ struct platform_device *pdev = to_platform_device(port->dev);
+ struct resource *res;
+ int size;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "cannot obtain I/O memory region");
+ return -ENODEV;
+ }
+ size = resource_size(res);
+
+ if (!devm_request_mem_region(port->dev, port->mapbase, size,
+ dev_name(port->dev))) {
+ dev_err(port->dev, "Memory region busy\n");
+ return -EBUSY;
+ }
+
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = devm_ioremap_nocache(port->dev,
+ port->mapbase,
+ size);
+ if (port->membase == NULL)
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static void meson_uart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_MESON;
+ meson_uart_request_port(port);
+ }
+}
+
+static struct uart_ops meson_uart_ops = {
+ .set_mctrl = meson_uart_set_mctrl,
+ .get_mctrl = meson_uart_get_mctrl,
+ .tx_empty = meson_uart_tx_empty,
+ .start_tx = meson_uart_start_tx,
+ .stop_tx = meson_uart_stop_tx,
+ .stop_rx = meson_uart_stop_rx,
+ .startup = meson_uart_startup,
+ .shutdown = meson_uart_shutdown,
+ .set_termios = meson_uart_set_termios,
+ .type = meson_uart_type,
+ .config_port = meson_uart_config_port,
+ .request_port = meson_uart_request_port,
+ .release_port = meson_uart_release_port,
+ .verify_port = meson_uart_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_MESON_CONSOLE
+
+static void meson_console_putchar(struct uart_port *port, int ch)
+{
+ if (!port->membase)
+ return;
+
+ while (readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL)
+ cpu_relax();
+ writel(ch, port->membase + AML_UART_WFIFO);
+}
+
+static void meson_serial_console_write(struct console *co, const char *s,
+ u_int count)
+{
+ struct uart_port *port;
+ unsigned long flags;
+ int locked;
+
+ port = meson_ports[co->index];
+ if (!port)
+ return;
+
+ local_irq_save(flags);
+ if (port->sysrq) {
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&port->lock);
+ } else {
+ spin_lock(&port->lock);
+ locked = 1;
+ }
+
+ uart_console_write(port, s, count, meson_console_putchar);
+
+ if (locked)
+ spin_unlock(&port->lock);
+ local_irq_restore(flags);
+}
+
+static int meson_serial_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index < 0 || co->index >= AML_UART_PORT_NUM)
+ return -EINVAL;
+
+ port = meson_ports[co->index];
+ if (!port || !port->membase)
+ return -ENODEV;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct console meson_serial_console = {
+ .name = AML_UART_DEV_NAME,
+ .write = meson_serial_console_write,
+ .device = uart_console_device,
+ .setup = meson_serial_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &meson_uart_driver,
+};
+
+static int __init meson_serial_console_init(void)
+{
+ register_console(&meson_serial_console);
+ return 0;
+}
+console_initcall(meson_serial_console_init);
+
+#define MESON_SERIAL_CONSOLE (&meson_serial_console)
+#else
+#define MESON_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_driver meson_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "meson_uart",
+ .dev_name = AML_UART_DEV_NAME,
+ .nr = AML_UART_PORT_NUM,
+ .cons = MESON_SERIAL_CONSOLE,
+};
+
+static int meson_uart_probe(struct platform_device *pdev)
+{
+ struct resource *res_mem, *res_irq;
+ struct uart_port *port;
+ struct clk *clk;
+ int ret = 0;
+
+ if (pdev->dev.of_node)
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+
+ if (pdev->id < 0 || pdev->id >= AML_UART_PORT_NUM)
+ return -EINVAL;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res_irq)
+ return -ENODEV;
+
+ if (meson_ports[pdev->id]) {
+ dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
+ return -EBUSY;
+ }
+
+ port = devm_kzalloc(&pdev->dev, sizeof(struct uart_port), GFP_KERNEL);
+ if (!port)
+ return -ENOMEM;
+
+ clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ port->uartclk = clk_get_rate(clk);
+ port->iotype = UPIO_MEM;
+ port->mapbase = res_mem->start;
+ port->irq = res_irq->start;
+ port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_LOW_LATENCY;
+ port->dev = &pdev->dev;
+ port->line = pdev->id;
+ port->type = PORT_MESON;
+ port->x_char = 0;
+ port->ops = &meson_uart_ops;
+ port->fifosize = 64;
+
+ meson_ports[pdev->id] = port;
+ platform_set_drvdata(pdev, port);
+
+ ret = uart_add_one_port(&meson_uart_driver, port);
+ if (ret)
+ meson_ports[pdev->id] = NULL;
+
+ return ret;
+}
+
+static int meson_uart_remove(struct platform_device *pdev)
+{
+ struct uart_port *port;
+
+ port = platform_get_drvdata(pdev);
+ uart_remove_one_port(&meson_uart_driver, port);
+ meson_ports[pdev->id] = NULL;
+
+ return 0;
+}
+
+
+static const struct of_device_id meson_uart_dt_match[] = {
+ { .compatible = "amlogic,meson-uart" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, meson_uart_dt_match);
+
+static struct platform_driver meson_uart_platform_driver = {
+ .probe = meson_uart_probe,
+ .remove = meson_uart_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "meson_uart",
+ .of_match_table = meson_uart_dt_match,
+ },
+};
+
+static int __init meson_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&meson_uart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&meson_uart_platform_driver);
+ if (ret)
+ uart_unregister_driver(&meson_uart_driver);
+
+ return ret;
+}
+
+static void __exit meson_uart_exit(void)
+{
+ platform_driver_unregister(&meson_uart_platform_driver);
+ uart_unregister_driver(&meson_uart_driver);
+}
+
+module_init(meson_uart_init);
+module_exit(meson_uart_exit);
+
+MODULE_AUTHOR("Carlo Caione <carlo@caione.org>");
+MODULE_DESCRIPTION("Amlogic Meson serial port driver");
+MODULE_LICENSE("GPL v2");
@@ -244,4 +244,7 @@
/* SC16IS74xx */
#define PORT_SC16IS7XX 108
+/* MESON */
+#define PORT_MESON 109
+
#endif /* _UAPILINUX_SERIAL_CORE_H */
The SoC has four fully functional UARTs which use the same programming model. They are named UART_A, UART_B, UART_C and UART_AO (Always-On) which cannot be powered off. Signed-off-by: Carlo Caione <carlo@caione.org> --- drivers/tty/serial/Kconfig | 18 ++ drivers/tty/serial/Makefile | 1 + drivers/tty/serial/meson_uart.c | 634 +++++++++++++++++++++++++++++++++++++++ include/uapi/linux/serial_core.h | 3 + 4 files changed, 656 insertions(+) create mode 100644 drivers/tty/serial/meson_uart.c