| Message ID | 1414793613-11798-2-git-send-email-andrew@lunn.ch (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Andrew Lunn (andrew@lunn.ch) wrote: > From: Claudio Leite <leitec@staticky.com> > > Add a device tree description of the DLINK DIR665 wireless access > point. The support for the 88E6171 switch will be added in a later > patch. > > Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Claudio Leite <leitec@staticky.com> > --- > > This description was mostly produced by Claudio Leite with a few > minor cleanups by my. > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/kirkwood-dir665.dts | 233 ++++++++++++++++++++++++++++++++++ > 2 files changed, 234 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-dir665.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 38c89cafa1ab..31529ccc67a0 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -104,6 +104,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \ > kirkwood-d2net.dtb \ > kirkwood-db-88f6281.dtb \ > kirkwood-db-88f6282.dtb \ > + kirkwood-dir665.dtb \ > kirkwood-dns320.dtb \ > kirkwood-dns325.dtb \ > kirkwood-dockstar.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/kirkwood-dir665.dts > new file mode 100644 > index 000000000000..ac945ea49940 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-dir665.dts > @@ -0,0 +1,233 @@ > +/* > + * Copyright (C) 2014 Claudio Leite <leitec@staticky.com> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > + > +/ { > + model = "D-Link DIR-665"; > + compatible = "dlink,dir-665", "marvell,kirkwood-88f6281", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; /* 128 MB */ > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8 earlyprintk"; > + stdout-path = &uart0; > + }; > + > + mbus { > + pcie-controller { > + status = "okay"; > + > + pcie@1,0 { > + status = "okay"; > + }; > + }; > + }; > + > + ocp@f1000000 { > + pinctrl: pin-controller@10000 { > + pinctrl-0 =< &pmx_led_usb > + &pmx_led_internet_blue > + &pmx_led_internet_amber > + &pmx_led_5g &pmx_led_status_blue > + &pmx_led_wps &pmx_led_status_amber > + &pmx_led_24g > + &pmx_btn_restart &pmx_btn_wps>; > + pinctrl-names = "default"; > + > + pmx_led_usb: pmx-led-usb { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > + pmx_led_internet_blue: pmx-led-internet-blue { > + marvell,pins = "mpp42"; > + marvell,function = "gpio"; > + }; > + pmx_led_internet_amber: pmx-led-internet-amber { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + pmx_led_5g: pmx-led-5g { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + pmx_led_status_blue: pmx-led-status-blue { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + pmx_led_wps: pmx-led-wps { > + marvell,pins = "mpp47"; > + marvell,function = "gpio"; > + }; > + pmx_led_status_amber: pmx-led-status-amber { > + marvell,pins = "mpp48"; > + marvell,function = "gpio"; > + }; > + pmx_led_24g: pmx-led-24g { > + marvell,pins = "mpp49"; > + marvell,function = "gpio"; > + }; > + pmx_btn_restart: pmx-btn-restart { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + pmx_btn_wps: pmx-btn-wps { > + marvell,pins = "mpp46"; > + marvell,function = "gpio"; > + }; > + }; > + > + spi@10600 { > + status = "okay"; > + m25p80@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "mxicy,mx25l12805d"; > + spi-max-frequency = <50000000>; > + reg = <0>; > + > + partition@0 { > + label = "uboot"; > + reg = <0x0 0x30000>; > + read-only; > + }; > + > + partition@30000 { > + label = "nvram"; > + reg = <0x30000 0x10000>; > + read-only; > + }; > + > + partition@40000 { > + label = "kernel"; > + reg = <0x40000 0x180000>; > + }; > + > + partition@1c0000 { > + label = "rootfs"; > + reg = <0x1c0000 0xe00000>; > + }; > + > + cal_data: partition@fc0000 { > + label = "cal_data"; > + reg = <0xfc0000 0x10000>; > + read-only; > + }; > + > + partition@fd0000 { > + label = "lang_pack"; > + reg = <0xfd0000 0x30000>; > + read-only; > + }; > + }; > + }; > + > + serial@12000 { > + status = "okay"; > + }; > + > + i2c@11000 { > + status = "okay"; > + }; > + > + ehci@50000 { > + status = "okay"; > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + > + blue-usb { > + label = "dir665:blue:usb"; > + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + }; > + blue-internet { > + /* Can only be turned on if the Internet > + * Ethernet port has Link > + */ > + label = "dir665:blue:internet"; > + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > + }; > + amber-internet { > + label = "dir665:amber:internet"; > + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; > + }; > + blue-wifi5g { > + label = "dir665:blue:5g"; > + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; > + }; > + blue-status { > + label = "dir665:blue:status"; > + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + blue-wps { > + label = "dir665:blue:wps"; > + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + }; > + amber-status { > + label = "dir665:amber:status"; > + gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; > + }; > + blue-24g { > + label = "dir665:blue:24g"; > + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reset { > + label = "reset"; > + linux,code = <KEY_RESTART>; > + gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; > + }; > + wps { > + label = "wps"; > + linux,code = <KEY_WPS_BUTTON>; > + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; > + > +&mdio { > + status = "okay"; > +}; > + > +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set > + * fixed speed and duplex. */ > +ð0 { > + status = "okay"; > + > + ethernet0-port@0 { > + speed = <1000>; > + duplex = <1>; > + }; > +}; > + > +/* eth1 is connected to the switch as well. However DSA only supports a > + * single CPU port. So leave this port disabled to avoid confusion. */ > + > +ð1 { > + status = "disabled"; > +}; > + > +/* There is no battery on the boards, so the RTC does not keep time > + * when there is now power, making it useless. */ > +&rtc { > + status = "disabled"; > +}; > -- > 2.1.1
On Fri, Oct 31, 2014 at 11:13:30PM +0100, Andrew Lunn wrote: > From: Claudio Leite <leitec@staticky.com> > > Add a device tree description of the DLINK DIR665 wireless access > point. The support for the 88E6171 switch will be added in a later > patch. > > Signed-off-by: Andrew Lunn <andrew@lunn.ch> > --- > > This description was mostly produced by Claudio Leite with a few > minor cleanups by my. > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/kirkwood-dir665.dts | 233 ++++++++++++++++++++++++++++++++++ > 2 files changed, 234 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-dir665.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 38c89cafa1ab..31529ccc67a0 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -104,6 +104,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \ > kirkwood-d2net.dtb \ > kirkwood-db-88f6281.dtb \ > kirkwood-db-88f6282.dtb \ > + kirkwood-dir665.dtb \ > kirkwood-dns320.dtb \ > kirkwood-dns325.dtb \ > kirkwood-dockstar.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/kirkwood-dir665.dts > new file mode 100644 > index 000000000000..ac945ea49940 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-dir665.dts > @@ -0,0 +1,233 @@ > +/* > + * Copyright (C) 2014 Claudio Leite <leitec@staticky.com> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > + > +/ { > + model = "D-Link DIR-665"; > + compatible = "dlink,dir-665", "marvell,kirkwood-88f6281", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; /* 128 MB */ > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8 earlyprintk"; > + stdout-path = &uart0; > + }; > + > + mbus { > + pcie-controller { > + status = "okay"; > + > + pcie@1,0 { > + status = "okay"; > + }; > + }; > + }; > + > + ocp@f1000000 { > + pinctrl: pin-controller@10000 { > + pinctrl-0 =< &pmx_led_usb > + &pmx_led_internet_blue > + &pmx_led_internet_amber > + &pmx_led_5g &pmx_led_status_blue > + &pmx_led_wps &pmx_led_status_amber > + &pmx_led_24g > + &pmx_btn_restart &pmx_btn_wps>; > + pinctrl-names = "default"; > + > + pmx_led_usb: pmx-led-usb { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > + pmx_led_internet_blue: pmx-led-internet-blue { > + marvell,pins = "mpp42"; > + marvell,function = "gpio"; > + }; > + pmx_led_internet_amber: pmx-led-internet-amber { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + pmx_led_5g: pmx-led-5g { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + pmx_led_status_blue: pmx-led-status-blue { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + pmx_led_wps: pmx-led-wps { > + marvell,pins = "mpp47"; > + marvell,function = "gpio"; > + }; > + pmx_led_status_amber: pmx-led-status-amber { > + marvell,pins = "mpp48"; > + marvell,function = "gpio"; > + }; > + pmx_led_24g: pmx-led-24g { > + marvell,pins = "mpp49"; > + marvell,function = "gpio"; > + }; > + pmx_btn_restart: pmx-btn-restart { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + pmx_btn_wps: pmx-btn-wps { > + marvell,pins = "mpp46"; > + marvell,function = "gpio"; > + }; > + }; > + > + spi@10600 { > + status = "okay"; > + m25p80@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "mxicy,mx25l12805d"; > + spi-max-frequency = <50000000>; > + reg = <0>; > + > + partition@0 { > + label = "uboot"; > + reg = <0x0 0x30000>; > + read-only; > + }; > + > + partition@30000 { > + label = "nvram"; > + reg = <0x30000 0x10000>; > + read-only; > + }; > + > + partition@40000 { > + label = "kernel"; > + reg = <0x40000 0x180000>; > + }; > + > + partition@1c0000 { > + label = "rootfs"; > + reg = <0x1c0000 0xe00000>; > + }; > + > + cal_data: partition@fc0000 { > + label = "cal_data"; > + reg = <0xfc0000 0x10000>; > + read-only; > + }; > + > + partition@fd0000 { > + label = "lang_pack"; > + reg = <0xfd0000 0x30000>; > + read-only; > + }; > + }; > + }; > + > + serial@12000 { > + status = "okay"; > + }; > + > + i2c@11000 { > + status = "okay"; > + }; > + > + ehci@50000 { > + status = "okay"; > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + > + blue-usb { > + label = "dir665:blue:usb"; > + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + }; > + blue-internet { > + /* Can only be turned on if the Internet > + * Ethernet port has Link > + */ > + label = "dir665:blue:internet"; > + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > + }; > + amber-internet { > + label = "dir665:amber:internet"; > + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; > + }; > + blue-wifi5g { > + label = "dir665:blue:5g"; > + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; > + }; > + blue-status { > + label = "dir665:blue:status"; > + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + blue-wps { > + label = "dir665:blue:wps"; > + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + }; > + amber-status { > + label = "dir665:amber:status"; > + gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; > + }; > + blue-24g { > + label = "dir665:blue:24g"; > + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reset { > + label = "reset"; > + linux,code = <KEY_RESTART>; > + gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; > + }; > + wps { > + label = "wps"; > + linux,code = <KEY_WPS_BUTTON>; > + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; > + > +&mdio { > + status = "okay"; > +}; > + > +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set > + * fixed speed and duplex. */ > +ð0 { > + status = "okay"; > + > + ethernet0-port@0 { > + speed = <1000>; > + duplex = <1>; > + }; > +}; > + > +/* eth1 is connected to the switch as well. However DSA only supports a > + * single CPU port. So leave this port disabled to avoid confusion. */ > + > +ð1 { > + status = "disabled"; > +}; > + > +/* There is no battery on the boards, so the RTC does not keep time > + * when there is now power, making it useless. */ Wow... so much for accurate logging. At any rate, s/now/no/. I'll fix it up when I pull it in if there's nothing else. thx, Jason. > +&rtc { > + status = "disabled"; > +}; > -- > 2.1.1 >
> > +/* There is no battery on the boards, so the RTC does not keep time > > + * when there is now power, making it useless. */ > > Wow... so much for accurate logging. At any rate, s/now/no/. I'll fix > it up when I pull it in if there's nothing else. Hi Jason I assume the firmware use NTP, But strangely, there does appear to be a crystal, at least i assume there is since there is no error message at boot time about the clock not ticking. So it probably does keep time so long as the power is on. I did wonder if my board has a flat battery, but i cannot find a battery... Andrew
On Sat, Nov 01, 2014 at 09:11:39PM +0100, Andrew Lunn wrote: > > > +/* There is no battery on the boards, so the RTC does not keep time > > > + * when there is now power, making it useless. */ > > > > Wow... so much for accurate logging. At any rate, s/now/no/. I'll fix > > it up when I pull it in if there's nothing else. > > Hi Jason > > I assume the firmware use NTP, But strangely, there does appear to be > a crystal, at least i assume there is since there is no error message > at boot time about the clock not ticking. So it probably does keep > time so long as the power is on. I did wonder if my board has a flat > battery, but i cannot find a battery... supercap? thx, Jason.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 38c89cafa1ab..31529ccc67a0 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -104,6 +104,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \ kirkwood-d2net.dtb \ kirkwood-db-88f6281.dtb \ kirkwood-db-88f6282.dtb \ + kirkwood-dir665.dtb \ kirkwood-dns320.dtb \ kirkwood-dns325.dtb \ kirkwood-dockstar.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/kirkwood-dir665.dts new file mode 100644 index 000000000000..ac945ea49940 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-dir665.dts @@ -0,0 +1,233 @@ +/* + * Copyright (C) 2014 Claudio Leite <leitec@staticky.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "D-Link DIR-665"; + compatible = "dlink,dir-665", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; /* 128 MB */ + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-0 =< &pmx_led_usb + &pmx_led_internet_blue + &pmx_led_internet_amber + &pmx_led_5g &pmx_led_status_blue + &pmx_led_wps &pmx_led_status_amber + &pmx_led_24g + &pmx_btn_restart &pmx_btn_wps>; + pinctrl-names = "default"; + + pmx_led_usb: pmx-led-usb { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + pmx_led_internet_blue: pmx-led-internet-blue { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + pmx_led_internet_amber: pmx-led-internet-amber { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + pmx_led_5g: pmx-led-5g { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + pmx_led_status_blue: pmx-led-status-blue { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + pmx_led_wps: pmx-led-wps { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + pmx_led_status_amber: pmx-led-status-amber { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + pmx_led_24g: pmx-led-24g { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + pmx_btn_restart: pmx-btn-restart { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + pmx_btn_wps: pmx-btn-wps { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + }; + + spi@10600 { + status = "okay"; + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mxicy,mx25l12805d"; + spi-max-frequency = <50000000>; + reg = <0>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "nvram"; + reg = <0x30000 0x10000>; + read-only; + }; + + partition@40000 { + label = "kernel"; + reg = <0x40000 0x180000>; + }; + + partition@1c0000 { + label = "rootfs"; + reg = <0x1c0000 0xe00000>; + }; + + cal_data: partition@fc0000 { + label = "cal_data"; + reg = <0xfc0000 0x10000>; + read-only; + }; + + partition@fd0000 { + label = "lang_pack"; + reg = <0xfd0000 0x30000>; + read-only; + }; + }; + }; + + serial@12000 { + status = "okay"; + }; + + i2c@11000 { + status = "okay"; + }; + + ehci@50000 { + status = "okay"; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + blue-usb { + label = "dir665:blue:usb"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + blue-internet { + /* Can only be turned on if the Internet + * Ethernet port has Link + */ + label = "dir665:blue:internet"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + amber-internet { + label = "dir665:amber:internet"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + }; + blue-wifi5g { + label = "dir665:blue:5g"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + blue-status { + label = "dir665:blue:status"; + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + blue-wps { + label = "dir665:blue:wps"; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + amber-status { + label = "dir665:amber:status"; + gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + }; + blue-24g { + label = "dir665:blue:24g"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; + }; + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&mdio { + status = "okay"; +}; + +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set + * fixed speed and duplex. */ +ð0 { + status = "okay"; + + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* eth1 is connected to the switch as well. However DSA only supports a + * single CPU port. So leave this port disabled to avoid confusion. */ + +ð1 { + status = "disabled"; +}; + +/* There is no battery on the boards, so the RTC does not keep time + * when there is now power, making it useless. */ +&rtc { + status = "disabled"; +};