diff mbox

[1/4] pci: iProc: define Broadcom iProc PCIe binding

Message ID 1418169871-19232-2-git-send-email-rjui@broadcom.com (mailing list archive)
State New, archived
Headers show

Commit Message

Ray Jui Dec. 10, 2014, 12:04 a.m. UTC 
Document the PCIe device tree binding for Broadcom iProc family of SoCs

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 .../devicetree/bindings/pci/brcm,iproc-pcie.txt    |   62 ++++++++++++++++++++
 1 file changed, 62 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt

Comments

Lucas Stach Dec. 10, 2014, 10:30 a.m. UTC | #1 
Am Dienstag, den 09.12.2014, 16:04 -0800 schrieb Ray Jui:
> Document the PCIe device tree binding for Broadcom iProc family of SoCs
> 
> Signed-off-by: Ray Jui <rjui@broadcom.com>
> Reviewed-by: Scott Branden <sbranden@broadcom.com>
> ---
>  .../devicetree/bindings/pci/brcm,iproc-pcie.txt    |   62 ++++++++++++++++++++
>  1 file changed, 62 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> 
> diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> new file mode 100644
> index 0000000..2467628
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> @@ -0,0 +1,62 @@
> +* Broadcom iProc PCIe controller
> +
> +Required properties:
> +- compatible: Must be "brcm,iproc-pcie"
> +- reg: base address and length of the PCIe controller and the MDIO interface
> +  that controls the PCIe PHY
> +- interrupts: interrupt IDs
> +- bus-range: PCI bus numbers covered
> +- #address-cells: set to <3>
> +- #size-cells: set to <2>
> +- device_type: set to "pci"
> +- ranges: ranges for the PCI memory and I/O regions
> +- phy-addr: MDC/MDIO adddress of the PCIe PHY
> +- have-msi-inten-reg: Required for legacy iProc PCIe controllers that need the
> +  MSI interrupt enable register to be set explicitly
> +
> +The Broadcom iProc PCie driver adapts the multi-domain structure, i.e., each
> +interface has its own domain and therefore has its own device node
> +Example:
> +
> +SoC specific DT Entry:
> +
> +	pcie0: pcie@18012000 {
> +		compatible = "brcm,iproc-pcie";
> +		reg = <0x18012000 0x1000>,
> +			<0x18002000 0x1000>;
> +		interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 97 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 98 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 99 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 100 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 101 IRQ_TYPE_NONE>;

This is missing the interrupt-map and interrupt-map-mask for the legacy
INTx interrupts. If you add this you don't need to have a special map
function in your driver, but can just use the standard
of_irq_parse_and_map_pci() function.

Regards,
Lucas

> +		bus-range = <0x00 0xFF>;
> +
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +		device_type = "pci";
> +		ranges = <0x81000000 0 0	  0x28000000 0 0x00010000   /* downstream I/O */
> +			  0x82000000 0 0x20000000 0x20000000 0 0x04000000>; /* non-prefetchable memory */
> +		phy-addr = <5>;
> +	};
> +
> +	pcie1: pcie@18013000 {
> +		compatible = "brcm,iproc-pcie";
> +		reg = <0x18013000 0x1000>,
> +			<0x18002000 0x1000>;
> +
> +		interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 103 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 104 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 105 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 106 IRQ_TYPE_NONE>,
> +			     <GIC_SPI 107 IRQ_TYPE_NONE>;
> +		bus-range = <0x00 0xFF>;
> +
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +		device_type = "pci";
> +		ranges = <0x81000000 0 0	  0x48000000 0 0x00010000   /* downstream I/O */
> +			  0x82000000 0 0x40000000 0x40000000 0 0x04000000>; /* non-prefetchable memory */
> +		phy-addr = <6>;
> +	};
Ray Jui Dec. 11, 2014, 1:37 a.m. UTC | #2 
On 12/10/2014 2:30 AM, Lucas Stach wrote:
>> +Example:
>> +
>> +SoC specific DT Entry:
>> +
>> +	pcie0: pcie@18012000 {
>> +		compatible = "brcm,iproc-pcie";
>> +		reg = <0x18012000 0x1000>,
>> +			<0x18002000 0x1000>;
>> +		interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
>> +			     <GIC_SPI 97 IRQ_TYPE_NONE>,
>> +			     <GIC_SPI 98 IRQ_TYPE_NONE>,
>> +			     <GIC_SPI 99 IRQ_TYPE_NONE>,
>> +			     <GIC_SPI 100 IRQ_TYPE_NONE>,
>> +			     <GIC_SPI 101 IRQ_TYPE_NONE>;
>
> This is missing the interrupt-map and interrupt-map-mask for the legacy
> INTx interrupts. If you add this you don't need to have a special map
> function in your driver, but can just use the standard
> of_irq_parse_and_map_pci() function.
>
> Regards,
> Lucas
>
Thanks for pointing this out. I will look into this and try it out.
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
new file mode 100644
index 0000000..2467628
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
@@ -0,0 +1,62 @@ 
+* Broadcom iProc PCIe controller
+
+Required properties:
+- compatible: Must be "brcm,iproc-pcie"
+- reg: base address and length of the PCIe controller and the MDIO interface
+  that controls the PCIe PHY
+- interrupts: interrupt IDs
+- bus-range: PCI bus numbers covered
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- device_type: set to "pci"
+- ranges: ranges for the PCI memory and I/O regions
+- phy-addr: MDC/MDIO adddress of the PCIe PHY
+- have-msi-inten-reg: Required for legacy iProc PCIe controllers that need the
+  MSI interrupt enable register to be set explicitly
+
+The Broadcom iProc PCie driver adapts the multi-domain structure, i.e., each
+interface has its own domain and therefore has its own device node
+Example:
+
+SoC specific DT Entry:
+
+	pcie0: pcie@18012000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18012000 0x1000>,
+			<0x18002000 0x1000>;
+		interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
+			     <GIC_SPI 97 IRQ_TYPE_NONE>,
+			     <GIC_SPI 98 IRQ_TYPE_NONE>,
+			     <GIC_SPI 99 IRQ_TYPE_NONE>,
+			     <GIC_SPI 100 IRQ_TYPE_NONE>,
+			     <GIC_SPI 101 IRQ_TYPE_NONE>;
+		bus-range = <0x00 0xFF>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x81000000 0 0	  0x28000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x20000000 0x20000000 0 0x04000000>; /* non-prefetchable memory */
+		phy-addr = <5>;
+	};
+
+	pcie1: pcie@18013000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18013000 0x1000>,
+			<0x18002000 0x1000>;
+
+		interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
+			     <GIC_SPI 103 IRQ_TYPE_NONE>,
+			     <GIC_SPI 104 IRQ_TYPE_NONE>,
+			     <GIC_SPI 105 IRQ_TYPE_NONE>,
+			     <GIC_SPI 106 IRQ_TYPE_NONE>,
+			     <GIC_SPI 107 IRQ_TYPE_NONE>;
+		bus-range = <0x00 0xFF>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x81000000 0 0	  0x48000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x40000000 0x40000000 0 0x04000000>; /* non-prefetchable memory */
+		phy-addr = <6>;
+	};