@@ -1398,10 +1398,7 @@ static void rockchip_irq_demux(unsigned int irq, struct irq_desc *desc)
{
struct irq_chip *chip = irq_get_chip(irq);
struct rockchip_pin_bank *bank = irq_get_handler_data(irq);
- u32 polarity = 0, data = 0;
u32 pend;
- bool edge_changed = false;
- unsigned long flags;
dev_dbg(bank->drvdata->dev, "got irq for bank %s\n", bank->name);
@@ -1409,12 +1406,6 @@ static void rockchip_irq_demux(unsigned int irq, struct irq_desc *desc)
pend = readl_relaxed(bank->reg_base + GPIO_INT_STATUS);
- if (bank->toggle_edge_mode) {
- polarity = readl_relaxed(bank->reg_base +
- GPIO_INT_POLARITY);
- data = readl_relaxed(bank->reg_base + GPIO_EXT_PORT);
- }
-
while (pend) {
unsigned int virq;
@@ -1434,27 +1425,31 @@ static void rockchip_irq_demux(unsigned int irq, struct irq_desc *desc)
* needs manual intervention.
*/
if (bank->toggle_edge_mode & BIT(irq)) {
- if (data & BIT(irq))
- polarity &= ~BIT(irq);
- else
- polarity |= BIT(irq);
+ u32 data, data_old, polarity;
+ unsigned long flags;
- edge_changed = true;
- }
+ data = readl_relaxed(bank->reg_base + GPIO_EXT_PORT);
+ do {
+ spin_lock_irqsave(&bank->slock, flags);
- generic_handle_irq(virq);
- }
+ polarity = readl_relaxed(bank->reg_base +
+ GPIO_INT_POLARITY);
+ if (data & BIT(irq))
+ polarity &= ~BIT(irq);
+ else
+ polarity |= BIT(irq);
+ writel(polarity,
+ bank->reg_base + GPIO_INT_POLARITY);
- if (bank->toggle_edge_mode && edge_changed) {
- /* Interrupt params should only be set with ints disabled */
- spin_lock_irqsave(&bank->slock, flags);
+ spin_unlock_irqrestore(&bank->slock, flags);
- data = readl_relaxed(bank->reg_base + GPIO_INTEN);
- writel_relaxed(0, bank->reg_base + GPIO_INTEN);
- writel(polarity, bank->reg_base + GPIO_INT_POLARITY);
- writel(data, bank->reg_base + GPIO_INTEN);
+ data_old = data;
+ data = readl_relaxed(bank->reg_base +
+ GPIO_EXT_PORT);
+ } while ((data & BIT(irq)) != (data_old & BIT(irq)));
+ }
- spin_unlock_irqrestore(&bank->slock, flags);
+ generic_handle_irq(virq);
}
chained_irq_exit(chip, desc);
I was seeing cases where I was losing interrupts when inserting and removing SD cards. Sometimes the card would get "stuck" in the inserted state. I believe that the problem was related to the code to handle the case where we needed both rising and falling edges. This code would disable the interrupt as the polarity was switched. If an interrupt came at the wrong time it could be lost. We'll match what the gpio-dwapb.c driver does upstream and change the interrupt polarity without disabling things. Signed-off-by: Doug Anderson <dianders@chromium.org> --- drivers/pinctrl/pinctrl-rockchip.c | 45 +++++++++++++++++--------------------- 1 file changed, 20 insertions(+), 25 deletions(-)