| Message ID | 1421231446-4776-3-git-send-email-alim.akhtar@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, If you want to enable the hs400 mode, need to add "mmc-hs400-1_8v" or "mmc-hs400-1_2v". But this patch didn't add them. do you have any other plan? On 01/14/2015 07:30 PM, Alim Akhtar wrote: > From: Seungwon Jeon <tgih.jun@samsung.com> > > HS400 timing values are added for SMDK5420, exynos5420-peach-pit > and exynos5800-peach-pi boards. > This also adds RCLK GPIO line, this gpio should be in pull-down > state. > > Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> > [Alim: addressed review comments] > --- > arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +++- > arch/arm/boot/dts/exynos5420-pinctrl.dtsi | 7 +++++++ > arch/arm/boot/dts/exynos5420-smdk5420.dts | 4 +++- > arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +++- > 4 files changed, 16 insertions(+), 3 deletions(-) > > diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts > index 9a050e1..7ffaba8 100644 > --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts > +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts > @@ -569,8 +569,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + samsung,dw-mshc-hs400-timing = <0 2>; > + read-strobe-delay = <90>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; > + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; > bus-width = <8>; > }; > > diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi > index ba686e4..8b15316 100644 > --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi > +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi > @@ -201,6 +201,13 @@ > samsung,pin-drv = <3>; > }; > > + sd0_rclk: sd0-rclk { I know it used to "sd0_rdqs", not "sd0_rclk". Change name. Best Regards, Jaehoon Chung > + samsung,pins = "gpc0-7"; > + samsung,pin-function = <2>; > + samsung,pin-pud = <1>; > + samsung,pin-drv = <3>; > + }; > + > sd1_cmd: sd1-cmd { > samsung,pins = "gpc1-1"; > samsung,pin-function = <2>; > diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts > index 8be3d7b..5290e79 100644 > --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts > +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts > @@ -80,8 +80,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + samsung,dw-mshc-hs400-timing = <0 2>; > + read-strobe-delay = <90>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; > + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; > bus-width = <8>; > cap-mmc-highspeed; > }; > diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts > index e8fdda8..fa1c858 100644 > --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts > +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts > @@ -557,8 +557,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + samsung,dw-mshc-hs400-timing = <0 2>; > + read-strobe-delay = <90>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; > + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; > bus-width = <8>; > }; > >
Hi Jaehoon On Wed, Jan 21, 2015 at 4:32 AM, Jaehoon Chung <jh80.chung@samsung.com> wrote: > Hi, > > If you want to enable the hs400 mode, need to add "mmc-hs400-1_8v" or "mmc-hs400-1_2v". > But this patch didn't add them. do you have any other plan? > Yes, right, plan is to send separate patch to enable hs400, as of now I am not sure if all the 5800-peach-pi boards are populated with emmc5.0 device or not. So I will enable HS400 after confirming this point. > On 01/14/2015 07:30 PM, Alim Akhtar wrote: >> From: Seungwon Jeon <tgih.jun@samsung.com> >> >> HS400 timing values are added for SMDK5420, exynos5420-peach-pit >> and exynos5800-peach-pi boards. >> This also adds RCLK GPIO line, this gpio should be in pull-down >> state. >> >> Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> >> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >> [Alim: addressed review comments] >> --- >> arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +++- >> arch/arm/boot/dts/exynos5420-pinctrl.dtsi | 7 +++++++ >> arch/arm/boot/dts/exynos5420-smdk5420.dts | 4 +++- >> arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +++- >> 4 files changed, 16 insertions(+), 3 deletions(-) >> >> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts >> index 9a050e1..7ffaba8 100644 >> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts >> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts >> @@ -569,8 +569,10 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + samsung,dw-mshc-hs400-timing = <0 2>; >> + read-strobe-delay = <90>; >> pinctrl-names = "default"; >> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >> bus-width = <8>; >> }; >> >> diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >> index ba686e4..8b15316 100644 >> --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >> +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >> @@ -201,6 +201,13 @@ >> samsung,pin-drv = <3>; >> }; >> >> + sd0_rclk: sd0-rclk { > > I know it used to "sd0_rdqs", not "sd0_rclk". > Change name. > Ok, I will change as per UM of 5800/5420, > Best Regards, > Jaehoon Chung >> + samsung,pins = "gpc0-7"; >> + samsung,pin-function = <2>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <3>; >> + }; >> + >> sd1_cmd: sd1-cmd { >> samsung,pins = "gpc1-1"; >> samsung,pin-function = <2>; >> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts >> index 8be3d7b..5290e79 100644 >> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts >> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts >> @@ -80,8 +80,10 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + samsung,dw-mshc-hs400-timing = <0 2>; >> + read-strobe-delay = <90>; >> pinctrl-names = "default"; >> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >> bus-width = <8>; >> cap-mmc-highspeed; >> }; >> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> index e8fdda8..fa1c858 100644 >> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts >> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> @@ -557,8 +557,10 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + samsung,dw-mshc-hs400-timing = <0 2>; >> + read-strobe-delay = <90>; >> pinctrl-names = "default"; >> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >> bus-width = <8>; >> }; >> >> >
Hi. On 01/21/2015 11:12 PM, Alim Akhtar wrote: > Hi Jaehoon > > On Wed, Jan 21, 2015 at 4:32 AM, Jaehoon Chung <jh80.chung@samsung.com> wrote: >> Hi, >> >> If you want to enable the hs400 mode, need to add "mmc-hs400-1_8v" or "mmc-hs400-1_2v". >> But this patch didn't add them. do you have any other plan? >> > Yes, right, plan is to send separate patch to enable hs400, as of now > I am not sure if all the 5800-peach-pi boards are populated with > emmc5.0 device or not. So I will enable HS400 after confirming this > point. I know if card is not support hs400, then it should be enabled to other bus mode. Best Regards, Jaehoon Chung >> On 01/14/2015 07:30 PM, Alim Akhtar wrote: >>> From: Seungwon Jeon <tgih.jun@samsung.com> >>> >>> HS400 timing values are added for SMDK5420, exynos5420-peach-pit >>> and exynos5800-peach-pi boards. >>> This also adds RCLK GPIO line, this gpio should be in pull-down >>> state. >>> >>> Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> >>> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >>> [Alim: addressed review comments] >>> --- >>> arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +++- >>> arch/arm/boot/dts/exynos5420-pinctrl.dtsi | 7 +++++++ >>> arch/arm/boot/dts/exynos5420-smdk5420.dts | 4 +++- >>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +++- >>> 4 files changed, 16 insertions(+), 3 deletions(-) >>> >>> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts >>> index 9a050e1..7ffaba8 100644 >>> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts >>> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts >>> @@ -569,8 +569,10 @@ >>> samsung,dw-mshc-ciu-div = <3>; >>> samsung,dw-mshc-sdr-timing = <0 4>; >>> samsung,dw-mshc-ddr-timing = <0 2>; >>> + samsung,dw-mshc-hs400-timing = <0 2>; >>> + read-strobe-delay = <90>; >>> pinctrl-names = "default"; >>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>> bus-width = <8>; >>> }; >>> >>> diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>> index ba686e4..8b15316 100644 >>> --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>> +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>> @@ -201,6 +201,13 @@ >>> samsung,pin-drv = <3>; >>> }; >>> >>> + sd0_rclk: sd0-rclk { >> >> I know it used to "sd0_rdqs", not "sd0_rclk". >> Change name. >> > Ok, I will change as per UM of 5800/5420, > >> Best Regards, >> Jaehoon Chung >>> + samsung,pins = "gpc0-7"; >>> + samsung,pin-function = <2>; >>> + samsung,pin-pud = <1>; >>> + samsung,pin-drv = <3>; >>> + }; >>> + >>> sd1_cmd: sd1-cmd { >>> samsung,pins = "gpc1-1"; >>> samsung,pin-function = <2>; >>> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts >>> index 8be3d7b..5290e79 100644 >>> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts >>> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts >>> @@ -80,8 +80,10 @@ >>> samsung,dw-mshc-ciu-div = <3>; >>> samsung,dw-mshc-sdr-timing = <0 4>; >>> samsung,dw-mshc-ddr-timing = <0 2>; >>> + samsung,dw-mshc-hs400-timing = <0 2>; >>> + read-strobe-delay = <90>; >>> pinctrl-names = "default"; >>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>> bus-width = <8>; >>> cap-mmc-highspeed; >>> }; >>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts >>> index e8fdda8..fa1c858 100644 >>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts >>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts >>> @@ -557,8 +557,10 @@ >>> samsung,dw-mshc-ciu-div = <3>; >>> samsung,dw-mshc-sdr-timing = <0 4>; >>> samsung,dw-mshc-ddr-timing = <0 2>; >>> + samsung,dw-mshc-hs400-timing = <0 2>; >>> + read-strobe-delay = <90>; >>> pinctrl-names = "default"; >>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>> bus-width = <8>; >>> }; >>> >>> >> > > >
Hi Jaehoon, Thanks for review. On Thu, Jan 22, 2015 at 11:28 AM, Jaehoon Chung <jh80.chung@samsung.com> wrote: > Hi. > > On 01/21/2015 11:12 PM, Alim Akhtar wrote: >> Hi Jaehoon >> >> On Wed, Jan 21, 2015 at 4:32 AM, Jaehoon Chung <jh80.chung@samsung.com> wrote: >>> Hi, >>> >>> If you want to enable the hs400 mode, need to add "mmc-hs400-1_8v" or "mmc-hs400-1_2v". >>> But this patch didn't add them. do you have any other plan? >>> >> Yes, right, plan is to send separate patch to enable hs400, as of now >> I am not sure if all the 5800-peach-pi boards are populated with >> emmc5.0 device or not. So I will enable HS400 after confirming this >> point. > > I know if card is not support hs400, then it should be enabled to other bus mode. > hmm...mmc-hs{200/400}-1_8v are host capabilities, so host should first support this, then we can enable it. ok, I will enable HS400 for peach-pi in this series. Also I checked UMs for 5420/5800, in UM, strobe signal is named as RCLK, so going to keep the same name as UM. Will resend the patches after modification shortly. > Best Regards, > Jaehoon Chung > >>> On 01/14/2015 07:30 PM, Alim Akhtar wrote: >>>> From: Seungwon Jeon <tgih.jun@samsung.com> >>>> >>>> HS400 timing values are added for SMDK5420, exynos5420-peach-pit >>>> and exynos5800-peach-pi boards. >>>> This also adds RCLK GPIO line, this gpio should be in pull-down >>>> state. >>>> >>>> Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> >>>> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >>>> [Alim: addressed review comments] >>>> --- >>>> arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +++- >>>> arch/arm/boot/dts/exynos5420-pinctrl.dtsi | 7 +++++++ >>>> arch/arm/boot/dts/exynos5420-smdk5420.dts | 4 +++- >>>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +++- >>>> 4 files changed, 16 insertions(+), 3 deletions(-) >>>> >>>> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts >>>> index 9a050e1..7ffaba8 100644 >>>> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts >>>> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts >>>> @@ -569,8 +569,10 @@ >>>> samsung,dw-mshc-ciu-div = <3>; >>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>> + samsung,dw-mshc-hs400-timing = <0 2>; >>>> + read-strobe-delay = <90>; >>>> pinctrl-names = "default"; >>>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>>> bus-width = <8>; >>>> }; >>>> >>>> diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>>> index ba686e4..8b15316 100644 >>>> --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>>> +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi >>>> @@ -201,6 +201,13 @@ >>>> samsung,pin-drv = <3>; >>>> }; >>>> >>>> + sd0_rclk: sd0-rclk { >>> >>> I know it used to "sd0_rdqs", not "sd0_rclk". >>> Change name. >>> >> Ok, I will change as per UM of 5800/5420, >> >>> Best Regards, >>> Jaehoon Chung >>>> + samsung,pins = "gpc0-7"; >>>> + samsung,pin-function = <2>; >>>> + samsung,pin-pud = <1>; >>>> + samsung,pin-drv = <3>; >>>> + }; >>>> + >>>> sd1_cmd: sd1-cmd { >>>> samsung,pins = "gpc1-1"; >>>> samsung,pin-function = <2>; >>>> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts >>>> index 8be3d7b..5290e79 100644 >>>> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts >>>> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts >>>> @@ -80,8 +80,10 @@ >>>> samsung,dw-mshc-ciu-div = <3>; >>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>> + samsung,dw-mshc-hs400-timing = <0 2>; >>>> + read-strobe-delay = <90>; >>>> pinctrl-names = "default"; >>>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>>> bus-width = <8>; >>>> cap-mmc-highspeed; >>>> }; >>>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts >>>> index e8fdda8..fa1c858 100644 >>>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts >>>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts >>>> @@ -557,8 +557,10 @@ >>>> samsung,dw-mshc-ciu-div = <3>; >>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>> + samsung,dw-mshc-hs400-timing = <0 2>; >>>> + read-strobe-delay = <90>; >>>> pinctrl-names = "default"; >>>> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; >>>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; >>>> bus-width = <8>; >>>> }; >>>> >>>> >>> >> >> >> >
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 9a050e1..7ffaba8 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -569,8 +569,10 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi index ba686e4..8b15316 100644 --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi @@ -201,6 +201,13 @@ samsung,pin-drv = <3>; }; + sd0_rclk: sd0-rclk { + samsung,pins = "gpc0-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <1>; + samsung,pin-drv = <3>; + }; + sd1_cmd: sd1-cmd { samsung,pins = "gpc1-1"; samsung,pin-function = <2>; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index 8be3d7b..5290e79 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -80,8 +80,10 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; bus-width = <8>; cap-mmc-highspeed; }; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index e8fdda8..fa1c858 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -557,8 +557,10 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8 &sd0_rclk>; bus-width = <8>; };