| Message ID | 1429898060-51944-1-git-send-email-s-anna@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 04/24/2015 12:54 PM, Suman Anna wrote: > The L3 Error handling on OMAP5 for the most part is very similar > to that of OMAP4, and had leveraged common data structures and > register layout definitions so far. Upon closer inspection, there > are a few minor differences causing an incorrect decoding and > reporting of the master NIU upon an error: > > 1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies > 11 bits on OMAP5 as against 8 bits on OMAP4, with the master > NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR > field. > 2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3 > input sources on OMAP5. The common DEBUGSS source is at a > different input on each SoC. > > Fix the above issues by using a OMAP5-specific compatible property > and using SoC-specific data where there are differences. > > Cc: Nishanth Menon <nm@ti.com> > Signed-off-by: Suman Anna <s-anna@ti.com> > --- > > Some validation traces by adding couple of traces and intentionally > creating L3 errors from DSP & IPU by accessing invalid Timers > > Before Patch: > OMAP4 [Correct] > IPU accessing Timer4 > [ 46.548095] flagmux = 1, err_reg = 0x8000 err_src = 0xf > [ 46.553344] mstaddr = 0x44 mask = 0xfc masterid = 0x11 > [ 46.553955] ------------[ cut here ]------------ > [ 46.563171] WARNING: CPU: 0 PID: 4 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 46.564941] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during > Functional access > > DSP accessing Timer5: > [ 114.018524] flagmux = 0, err_reg = 0x4 err_src = 0x2 > [ 114.023498] mstaddr = 0x20 mask = 0xfc masterid = 0x8 > [ 114.028564] ------------[ cut here ]------------ > [ 114.033233] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 114.042572] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional > access > > OMAP5 [Incorrect] > IPU accessing Timer4: > [ 29.579306] flagmux = 1, err_reg = 0x8000 err_src = 0xf > [ 29.584550] mstaddr = 0x220 mask = 0xfc masterid = 0x8 > [ 29.589705] ------------[ cut here ]------------ > [ 29.594345] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 29.603774] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET L4PER3 (Idle): Data Access in User mode during Functional > access > > DSP accessing Timer5: > [ 21.347105] flagmux = 0, err_reg = 0x4 err_src = 0x2 > [ 21.352091] mstaddr = 0x100 mask = 0xfc masterid = 0x0 > [ 21.357250] ------------[ cut here ]------------ > [ 21.361896] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 21.371242] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET ABE (Idle): Data Access in Supervisor mode during Functional > access > > After Patch: > OMAP4 same as above > > OMAP5 [Corrected] > IPU accessing Timer4 > [ 67.896693] flagmux = 1, err_reg = 0x8000 err_src = 0xf > [ 67.901940] mstaddr = 0x220 mask = 0x7e0 masterid = 0x11 > [ 67.907275] ------------[ cut here ]------------ > [ 67.911924] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 67.921357] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during > Functional access > > DSP accessing Timer5 > [ 24.452565] flagmux = 0, err_reg = 0x4 err_src = 0x2 > [ 24.457552] mstaddr = 0x100 mask = 0x7e0 masterid = 0x8 > [ 24.462798] ------------[ cut here ]------------ > [ 24.467449] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() > [ 24.476795] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional > access > > > .../devicetree/bindings/arm/omap/l3-noc.txt | 1 + > arch/arm/boot/dts/omap5.dtsi | 2 +- > drivers/bus/omap_l3_noc.c | 5 ++- > drivers/bus/omap_l3_noc.h | 52 ++++++++++++++++------ > 4 files changed, 44 insertions(+), 16 deletions(-) > > diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt > index 974624ea68f6..161448da959d 100644 > --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt > +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt > @@ -6,6 +6,7 @@ provided by Arteris. > Required properties: > - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family > Should be "ti,omap4-l3-noc" for OMAP4 family > + Should be "ti,omap5-l3-noc" for OMAP5 family > Should be "ti,dra7-l3-noc" for DRA7 family > Should be "ti,am4372-l3-noc" for AM43 family > - reg: Contains L3 register address range for each noc domain. > diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi > index efe5f737f39b..7d24ae0306b5 100644 > --- a/arch/arm/boot/dts/omap5.dtsi > +++ b/arch/arm/boot/dts/omap5.dtsi > @@ -128,7 +128,7 @@ > * hierarchy. > */ > ocp { > - compatible = "ti,omap4-l3-noc", "simple-bus"; > + compatible = "ti,omap5-l3-noc", "simple-bus"; > #address-cells = <1>; > #size-cells = <1>; > ranges; > diff --git a/drivers/bus/omap_l3_noc.c b/drivers/bus/omap_l3_noc.c > index 11f7982cbdb3..ebee57d715d2 100644 > --- a/drivers/bus/omap_l3_noc.c > +++ b/drivers/bus/omap_l3_noc.c > @@ -1,7 +1,7 @@ > /* > * OMAP L3 Interconnect error handling driver > * > - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ > + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ > * Santosh Shilimkar <santosh.shilimkar@ti.com> > * Sricharan <r.sricharan@ti.com> > * > @@ -233,7 +233,8 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3) > } > > static const struct of_device_id l3_noc_match[] = { > - {.compatible = "ti,omap4-l3-noc", .data = &omap_l3_data}, > + {.compatible = "ti,omap4-l3-noc", .data = &omap4_l3_data}, > + {.compatible = "ti,omap5-l3-noc", .data = &omap5_l3_data}, > {.compatible = "ti,dra7-l3-noc", .data = &dra_l3_data}, > {.compatible = "ti,am4372-l3-noc", .data = &am4372_l3_data}, > {}, > diff --git a/drivers/bus/omap_l3_noc.h b/drivers/bus/omap_l3_noc.h > index 95254585db86..3ba40db7380b 100644 > --- a/drivers/bus/omap_l3_noc.h > +++ b/drivers/bus/omap_l3_noc.h > @@ -1,7 +1,7 @@ > /* > * OMAP L3 Interconnect error handling driver header > * > - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ > + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ > * Santosh Shilimkar <santosh.shilimkar@ti.com> > * sricharan <r.sricharan@ti.com> > * > @@ -175,16 +175,14 @@ static struct l3_flagmux_data omap_l3_flagmux_clk2 = { > }; > > > -static struct l3_target_data omap_l3_target_data_clk3[] = { > - {0x0100, "EMUSS",}, > - {0x0300, "DEBUG SOURCE",}, > - {0x0, "HOST CLK3",}, > +static struct l3_target_data omap4_l3_target_data_clk3[] = { > + {0x0100, "DEBUGSS",}, > }; > > -static struct l3_flagmux_data omap_l3_flagmux_clk3 = { > +static struct l3_flagmux_data omap4_l3_flagmux_clk3 = { > .offset = 0x0200, > - .l3_targ = omap_l3_target_data_clk3, > - .num_targ_data = ARRAY_SIZE(omap_l3_target_data_clk3), > + .l3_targ = omap4_l3_target_data_clk3, > + .num_targ_data = ARRAY_SIZE(omap4_l3_target_data_clk3), > }; > > static struct l3_masters_data omap_l3_masters[] = { > @@ -215,21 +213,49 @@ static struct l3_masters_data omap_l3_masters[] = { > { 0x32, "USBHOSTFS"} > }; > > -static struct l3_flagmux_data *omap_l3_flagmux[] = { > +static struct l3_flagmux_data *omap4_l3_flagmux[] = { > &omap_l3_flagmux_clk1, > &omap_l3_flagmux_clk2, > - &omap_l3_flagmux_clk3, > + &omap4_l3_flagmux_clk3, > }; > > -static const struct omap_l3 omap_l3_data = { > - .l3_flagmux = omap_l3_flagmux, > - .num_modules = ARRAY_SIZE(omap_l3_flagmux), > +static const struct omap_l3 omap4_l3_data = { > + .l3_flagmux = omap4_l3_flagmux, > + .num_modules = ARRAY_SIZE(omap4_l3_flagmux), > .l3_masters = omap_l3_masters, > .num_masters = ARRAY_SIZE(omap_l3_masters), > /* The 6 MSBs of register field used to distinguish initiator */ > .mst_addr_mask = 0xFC, > }; > > +/* OMAP5 data */ > +static struct l3_target_data omap5_l3_target_data_clk3[] = { > + {0x0100, "L3INSTR",}, > + {0x0300, "DEBUGSS",}, > + {0x0, "HOSTCLK3",}, "HOST CLK" > +}; > + > +static struct l3_flagmux_data omap5_l3_flagmux_clk3 = { > + .offset = 0x0200, > + .l3_targ = omap5_l3_target_data_clk3, > + .num_targ_data = ARRAY_SIZE(omap5_l3_target_data_clk3), > +}; > + > +static struct l3_flagmux_data *omap5_l3_flagmux[] = { > + &omap_l3_flagmux_clk1, > + &omap_l3_flagmux_clk2, > + &omap5_l3_flagmux_clk3, > +}; > + > +static const struct omap_l3 omap5_l3_data = { > + .l3_flagmux = omap5_l3_flagmux, > + .num_modules = ARRAY_SIZE(omap5_l3_flagmux), > + .l3_masters = omap_l3_masters, > + .num_masters = ARRAY_SIZE(omap_l3_masters), > + /* The 6 MSBs of register field used to distinguish initiator */ > + .mst_addr_mask = 0x7E0, > +}; > + > /* DRA7 data */ > static struct l3_target_data dra_l3_target_data_clk1[] = { > {0x2a00, "AES1",}, > If tony does not mind dts+driver patch, then except for the above comment: Acked-by: Nishanth Menon <nm@ti.com>
On 04/24/2015 01:33 PM, Nishanth Menon wrote: > On 04/24/2015 12:54 PM, Suman Anna wrote: >> The L3 Error handling on OMAP5 for the most part is very similar >> to that of OMAP4, and had leveraged common data structures and >> register layout definitions so far. Upon closer inspection, there >> are a few minor differences causing an incorrect decoding and >> reporting of the master NIU upon an error: >> >> 1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies >> 11 bits on OMAP5 as against 8 bits on OMAP4, with the master >> NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR >> field. >> 2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3 >> input sources on OMAP5. The common DEBUGSS source is at a >> different input on each SoC. >> >> Fix the above issues by using a OMAP5-specific compatible property >> and using SoC-specific data where there are differences. >> >> Cc: Nishanth Menon <nm@ti.com> >> Signed-off-by: Suman Anna <s-anna@ti.com> >> --- >> >> Some validation traces by adding couple of traces and intentionally >> creating L3 errors from DSP & IPU by accessing invalid Timers >> >> Before Patch: >> OMAP4 [Correct] >> IPU accessing Timer4 >> [ 46.548095] flagmux = 1, err_reg = 0x8000 err_src = 0xf >> [ 46.553344] mstaddr = 0x44 mask = 0xfc masterid = 0x11 >> [ 46.553955] ------------[ cut here ]------------ >> [ 46.563171] WARNING: CPU: 0 PID: 4 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 46.564941] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during >> Functional access >> >> DSP accessing Timer5: >> [ 114.018524] flagmux = 0, err_reg = 0x4 err_src = 0x2 >> [ 114.023498] mstaddr = 0x20 mask = 0xfc masterid = 0x8 >> [ 114.028564] ------------[ cut here ]------------ >> [ 114.033233] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 114.042572] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional >> access >> >> OMAP5 [Incorrect] >> IPU accessing Timer4: >> [ 29.579306] flagmux = 1, err_reg = 0x8000 err_src = 0xf >> [ 29.584550] mstaddr = 0x220 mask = 0xfc masterid = 0x8 >> [ 29.589705] ------------[ cut here ]------------ >> [ 29.594345] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 29.603774] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET L4PER3 (Idle): Data Access in User mode during Functional >> access >> >> DSP accessing Timer5: >> [ 21.347105] flagmux = 0, err_reg = 0x4 err_src = 0x2 >> [ 21.352091] mstaddr = 0x100 mask = 0xfc masterid = 0x0 >> [ 21.357250] ------------[ cut here ]------------ >> [ 21.361896] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 21.371242] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET ABE (Idle): Data Access in Supervisor mode during Functional >> access >> >> After Patch: >> OMAP4 same as above >> >> OMAP5 [Corrected] >> IPU accessing Timer4 >> [ 67.896693] flagmux = 1, err_reg = 0x8000 err_src = 0xf >> [ 67.901940] mstaddr = 0x220 mask = 0x7e0 masterid = 0x11 >> [ 67.907275] ------------[ cut here ]------------ >> [ 67.911924] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 67.921357] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during >> Functional access >> >> DSP accessing Timer5 >> [ 24.452565] flagmux = 0, err_reg = 0x4 err_src = 0x2 >> [ 24.457552] mstaddr = 0x100 mask = 0x7e0 masterid = 0x8 >> [ 24.462798] ------------[ cut here ]------------ >> [ 24.467449] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() >> [ 24.476795] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional >> access >> >> >> .../devicetree/bindings/arm/omap/l3-noc.txt | 1 + >> arch/arm/boot/dts/omap5.dtsi | 2 +- >> drivers/bus/omap_l3_noc.c | 5 ++- >> drivers/bus/omap_l3_noc.h | 52 ++++++++++++++++------ >> 4 files changed, 44 insertions(+), 16 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt >> index 974624ea68f6..161448da959d 100644 >> --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt >> +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt >> @@ -6,6 +6,7 @@ provided by Arteris. >> Required properties: >> - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family >> Should be "ti,omap4-l3-noc" for OMAP4 family >> + Should be "ti,omap5-l3-noc" for OMAP5 family >> Should be "ti,dra7-l3-noc" for DRA7 family >> Should be "ti,am4372-l3-noc" for AM43 family >> - reg: Contains L3 register address range for each noc domain. >> diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi >> index efe5f737f39b..7d24ae0306b5 100644 >> --- a/arch/arm/boot/dts/omap5.dtsi >> +++ b/arch/arm/boot/dts/omap5.dtsi >> @@ -128,7 +128,7 @@ >> * hierarchy. >> */ >> ocp { >> - compatible = "ti,omap4-l3-noc", "simple-bus"; >> + compatible = "ti,omap5-l3-noc", "simple-bus"; >> #address-cells = <1>; >> #size-cells = <1>; >> ranges; >> diff --git a/drivers/bus/omap_l3_noc.c b/drivers/bus/omap_l3_noc.c >> index 11f7982cbdb3..ebee57d715d2 100644 >> --- a/drivers/bus/omap_l3_noc.c >> +++ b/drivers/bus/omap_l3_noc.c >> @@ -1,7 +1,7 @@ >> /* >> * OMAP L3 Interconnect error handling driver >> * >> - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ >> + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ >> * Santosh Shilimkar <santosh.shilimkar@ti.com> >> * Sricharan <r.sricharan@ti.com> >> * >> @@ -233,7 +233,8 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3) >> } >> >> static const struct of_device_id l3_noc_match[] = { >> - {.compatible = "ti,omap4-l3-noc", .data = &omap_l3_data}, >> + {.compatible = "ti,omap4-l3-noc", .data = &omap4_l3_data}, >> + {.compatible = "ti,omap5-l3-noc", .data = &omap5_l3_data}, >> {.compatible = "ti,dra7-l3-noc", .data = &dra_l3_data}, >> {.compatible = "ti,am4372-l3-noc", .data = &am4372_l3_data}, >> {}, >> diff --git a/drivers/bus/omap_l3_noc.h b/drivers/bus/omap_l3_noc.h >> index 95254585db86..3ba40db7380b 100644 >> --- a/drivers/bus/omap_l3_noc.h >> +++ b/drivers/bus/omap_l3_noc.h >> @@ -1,7 +1,7 @@ >> /* >> * OMAP L3 Interconnect error handling driver header >> * >> - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ >> + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ >> * Santosh Shilimkar <santosh.shilimkar@ti.com> >> * sricharan <r.sricharan@ti.com> >> * >> @@ -175,16 +175,14 @@ static struct l3_flagmux_data omap_l3_flagmux_clk2 = { >> }; >> >> >> -static struct l3_target_data omap_l3_target_data_clk3[] = { >> - {0x0100, "EMUSS",}, >> - {0x0300, "DEBUG SOURCE",}, >> - {0x0, "HOST CLK3",}, >> +static struct l3_target_data omap4_l3_target_data_clk3[] = { >> + {0x0100, "DEBUGSS",}, >> }; >> >> -static struct l3_flagmux_data omap_l3_flagmux_clk3 = { >> +static struct l3_flagmux_data omap4_l3_flagmux_clk3 = { >> .offset = 0x0200, >> - .l3_targ = omap_l3_target_data_clk3, >> - .num_targ_data = ARRAY_SIZE(omap_l3_target_data_clk3), >> + .l3_targ = omap4_l3_target_data_clk3, >> + .num_targ_data = ARRAY_SIZE(omap4_l3_target_data_clk3), >> }; >> >> static struct l3_masters_data omap_l3_masters[] = { >> @@ -215,21 +213,49 @@ static struct l3_masters_data omap_l3_masters[] = { >> { 0x32, "USBHOSTFS"} >> }; >> >> -static struct l3_flagmux_data *omap_l3_flagmux[] = { >> +static struct l3_flagmux_data *omap4_l3_flagmux[] = { >> &omap_l3_flagmux_clk1, >> &omap_l3_flagmux_clk2, >> - &omap_l3_flagmux_clk3, >> + &omap4_l3_flagmux_clk3, >> }; >> >> -static const struct omap_l3 omap_l3_data = { >> - .l3_flagmux = omap_l3_flagmux, >> - .num_modules = ARRAY_SIZE(omap_l3_flagmux), >> +static const struct omap_l3 omap4_l3_data = { >> + .l3_flagmux = omap4_l3_flagmux, >> + .num_modules = ARRAY_SIZE(omap4_l3_flagmux), >> .l3_masters = omap_l3_masters, >> .num_masters = ARRAY_SIZE(omap_l3_masters), >> /* The 6 MSBs of register field used to distinguish initiator */ >> .mst_addr_mask = 0xFC, >> }; >> >> +/* OMAP5 data */ >> +static struct l3_target_data omap5_l3_target_data_clk3[] = { >> + {0x0100, "L3INSTR",}, >> + {0x0300, "DEBUGSS",}, >> + {0x0, "HOSTCLK3",}, > > "HOST CLK" Why? I followed the convention used for the other two HOST CLKs for the OMAP4/5 data, see omap_l3_target_data_clk1 and omap_l3_target_data_clk2. The TRM name used is HOST_CLK3 (Table 14-31 Interconnect Flag Mapping, Section 14.2.3.9.3 of OMAP543x_ES2.0_Public_TRM_vX.pdf), but the code doesn't use the underscores. regards Suman > >> +}; >> + >> +static struct l3_flagmux_data omap5_l3_flagmux_clk3 = { >> + .offset = 0x0200, >> + .l3_targ = omap5_l3_target_data_clk3, >> + .num_targ_data = ARRAY_SIZE(omap5_l3_target_data_clk3), >> +}; >> + >> +static struct l3_flagmux_data *omap5_l3_flagmux[] = { >> + &omap_l3_flagmux_clk1, >> + &omap_l3_flagmux_clk2, >> + &omap5_l3_flagmux_clk3, >> +}; >> + >> +static const struct omap_l3 omap5_l3_data = { >> + .l3_flagmux = omap5_l3_flagmux, >> + .num_modules = ARRAY_SIZE(omap5_l3_flagmux), >> + .l3_masters = omap_l3_masters, >> + .num_masters = ARRAY_SIZE(omap_l3_masters), >> + /* The 6 MSBs of register field used to distinguish initiator */ >> + .mst_addr_mask = 0x7E0, >> +}; >> + >> /* DRA7 data */ >> static struct l3_target_data dra_l3_target_data_clk1[] = { >> {0x2a00, "AES1",}, >> > > If tony does not mind dts+driver patch, then except for the above comment: > > Acked-by: Nishanth Menon <nm@ti.com> > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Apr 24, 2015 at 2:10 PM, Suman Anna <s-anna@ti.com> wrote: > On 04/24/2015 01:33 PM, Nishanth Menon wrote: >> On 04/24/2015 12:54 PM, Suman Anna wrote: ... >>> -static struct l3_target_data omap_l3_target_data_clk3[] = { >>> - {0x0100, "EMUSS",}, >>> - {0x0300, "DEBUG SOURCE",}, >>> - {0x0, "HOST CLK3",}, ^^ this was HOST CLK3 .. >>> >>> +/* OMAP5 data */ >>> +static struct l3_target_data omap5_l3_target_data_clk3[] = { >>> + {0x0100, "L3INSTR",}, >>> + {0x0300, "DEBUGSS",}, >>> + {0x0, "HOSTCLK3",}, >> >> "HOST CLK" > > Why? I followed the convention used for the other two HOST CLKs for the so asked, if it should be HOST<space>CLK3 -- Regards, Nishanth Menon -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04/24/2015 02:38 PM, Nishanth Menon wrote: > On Fri, Apr 24, 2015 at 2:10 PM, Suman Anna <s-anna@ti.com> wrote: >> On 04/24/2015 01:33 PM, Nishanth Menon wrote: >>> On 04/24/2015 12:54 PM, Suman Anna wrote: > > ... >>>> -static struct l3_target_data omap_l3_target_data_clk3[] = { >>>> - {0x0100, "EMUSS",}, >>>> - {0x0300, "DEBUG SOURCE",}, >>>> - {0x0, "HOST CLK3",}, > ^^ this was HOST CLK3 > .. >>>> >>>> +/* OMAP5 data */ >>>> +static struct l3_target_data omap5_l3_target_data_clk3[] = { >>>> + {0x0100, "L3INSTR",}, >>>> + {0x0300, "DEBUGSS",}, >>>> + {0x0, "HOSTCLK3",}, >>> >>> "HOST CLK" >> >> Why? I followed the convention used for the other two HOST CLKs for the > > so asked, if it should be HOST<space>CLK3 Aah ok, you missed the trailing number before. In anycase, this was intentional to match HOSTCLK1 and HOSTCLK2 on OMAP4/5. Overall, the names are somewhat non-standard, some use underscores and some others strip out the underscore and do not use any spaces in between either. "HOST CLK3" would be the only one to use a space for OMAP4, so I got rid of it, so hope that's ok with you. regards Suman -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04/24/2015 02:54 PM, Suman Anna wrote: > On 04/24/2015 02:38 PM, Nishanth Menon wrote: >> On Fri, Apr 24, 2015 at 2:10 PM, Suman Anna <s-anna@ti.com> wrote: >>> On 04/24/2015 01:33 PM, Nishanth Menon wrote: >>>> On 04/24/2015 12:54 PM, Suman Anna wrote: >> >> ... >>>>> -static struct l3_target_data omap_l3_target_data_clk3[] = { >>>>> - {0x0100, "EMUSS",}, >>>>> - {0x0300, "DEBUG SOURCE",}, >>>>> - {0x0, "HOST CLK3",}, >> ^^ this was HOST CLK3 >> .. >>>>> >>>>> +/* OMAP5 data */ >>>>> +static struct l3_target_data omap5_l3_target_data_clk3[] = { >>>>> + {0x0100, "L3INSTR",}, >>>>> + {0x0300, "DEBUGSS",}, >>>>> + {0x0, "HOSTCLK3",}, >>>> >>>> "HOST CLK" >>> >>> Why? I followed the convention used for the other two HOST CLKs for the >> >> so asked, if it should be HOST<space>CLK3 > > Aah ok, you missed the trailing number before. In anycase, this was Sorry about that.. > intentional to match HOSTCLK1 and HOSTCLK2 on OMAP4/5. Overall, the > names are somewhat non-standard, some use underscores and some others > strip out the underscore and do not use any spaces in between either. > "HOST CLK3" would be the only one to use a space for OMAP4, so I got rid > of it, so hope that's ok with you. would have been nice to cover that in commit message. no biggie for me.
* Nishanth Menon <nm@ti.com> [150424 11:34]: > On 04/24/2015 12:54 PM, Suman Anna wrote: > > The L3 Error handling on OMAP5 for the most part is very similar > > to that of OMAP4, and had leveraged common data structures and > > register layout definitions so far. Upon closer inspection, there > > are a few minor differences causing an incorrect decoding and > > reporting of the master NIU upon an error: > > > > 1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies > > 11 bits on OMAP5 as against 8 bits on OMAP4, with the master > > NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR > > field. > > 2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3 > > input sources on OMAP5. The common DEBUGSS source is at a > > different input on each SoC. > > > > Fix the above issues by using a OMAP5-specific compatible property > > and using SoC-specific data where there are differences. > > > > Cc: Nishanth Menon <nm@ti.com> > > Signed-off-by: Suman Anna <s-anna@ti.com> ... > If tony does not mind dts+driver patch, then except for the above comment: > > Acked-by: Nishanth Menon <nm@ti.com> Looks OK to me for a fix. In general we want to have the .dts changes separated from the driver changes though. Applying into omap-for-v4.1/fixes. Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 974624ea68f6..161448da959d 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,omap5-l3-noc" for OMAP5 family Should be "ti,dra7-l3-noc" for DRA7 family Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index efe5f737f39b..7d24ae0306b5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -128,7 +128,7 @@ * hierarchy. */ ocp { - compatible = "ti,omap4-l3-noc", "simple-bus"; + compatible = "ti,omap5-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; diff --git a/drivers/bus/omap_l3_noc.c b/drivers/bus/omap_l3_noc.c index 11f7982cbdb3..ebee57d715d2 100644 --- a/drivers/bus/omap_l3_noc.c +++ b/drivers/bus/omap_l3_noc.c @@ -1,7 +1,7 @@ /* * OMAP L3 Interconnect error handling driver * - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ * Santosh Shilimkar <santosh.shilimkar@ti.com> * Sricharan <r.sricharan@ti.com> * @@ -233,7 +233,8 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3) } static const struct of_device_id l3_noc_match[] = { - {.compatible = "ti,omap4-l3-noc", .data = &omap_l3_data}, + {.compatible = "ti,omap4-l3-noc", .data = &omap4_l3_data}, + {.compatible = "ti,omap5-l3-noc", .data = &omap5_l3_data}, {.compatible = "ti,dra7-l3-noc", .data = &dra_l3_data}, {.compatible = "ti,am4372-l3-noc", .data = &am4372_l3_data}, {}, diff --git a/drivers/bus/omap_l3_noc.h b/drivers/bus/omap_l3_noc.h index 95254585db86..3ba40db7380b 100644 --- a/drivers/bus/omap_l3_noc.h +++ b/drivers/bus/omap_l3_noc.h @@ -1,7 +1,7 @@ /* * OMAP L3 Interconnect error handling driver header * - * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/ * Santosh Shilimkar <santosh.shilimkar@ti.com> * sricharan <r.sricharan@ti.com> * @@ -175,16 +175,14 @@ static struct l3_flagmux_data omap_l3_flagmux_clk2 = { }; -static struct l3_target_data omap_l3_target_data_clk3[] = { - {0x0100, "EMUSS",}, - {0x0300, "DEBUG SOURCE",}, - {0x0, "HOST CLK3",}, +static struct l3_target_data omap4_l3_target_data_clk3[] = { + {0x0100, "DEBUGSS",}, }; -static struct l3_flagmux_data omap_l3_flagmux_clk3 = { +static struct l3_flagmux_data omap4_l3_flagmux_clk3 = { .offset = 0x0200, - .l3_targ = omap_l3_target_data_clk3, - .num_targ_data = ARRAY_SIZE(omap_l3_target_data_clk3), + .l3_targ = omap4_l3_target_data_clk3, + .num_targ_data = ARRAY_SIZE(omap4_l3_target_data_clk3), }; static struct l3_masters_data omap_l3_masters[] = { @@ -215,21 +213,49 @@ static struct l3_masters_data omap_l3_masters[] = { { 0x32, "USBHOSTFS"} }; -static struct l3_flagmux_data *omap_l3_flagmux[] = { +static struct l3_flagmux_data *omap4_l3_flagmux[] = { &omap_l3_flagmux_clk1, &omap_l3_flagmux_clk2, - &omap_l3_flagmux_clk3, + &omap4_l3_flagmux_clk3, }; -static const struct omap_l3 omap_l3_data = { - .l3_flagmux = omap_l3_flagmux, - .num_modules = ARRAY_SIZE(omap_l3_flagmux), +static const struct omap_l3 omap4_l3_data = { + .l3_flagmux = omap4_l3_flagmux, + .num_modules = ARRAY_SIZE(omap4_l3_flagmux), .l3_masters = omap_l3_masters, .num_masters = ARRAY_SIZE(omap_l3_masters), /* The 6 MSBs of register field used to distinguish initiator */ .mst_addr_mask = 0xFC, }; +/* OMAP5 data */ +static struct l3_target_data omap5_l3_target_data_clk3[] = { + {0x0100, "L3INSTR",}, + {0x0300, "DEBUGSS",}, + {0x0, "HOSTCLK3",}, +}; + +static struct l3_flagmux_data omap5_l3_flagmux_clk3 = { + .offset = 0x0200, + .l3_targ = omap5_l3_target_data_clk3, + .num_targ_data = ARRAY_SIZE(omap5_l3_target_data_clk3), +}; + +static struct l3_flagmux_data *omap5_l3_flagmux[] = { + &omap_l3_flagmux_clk1, + &omap_l3_flagmux_clk2, + &omap5_l3_flagmux_clk3, +}; + +static const struct omap_l3 omap5_l3_data = { + .l3_flagmux = omap5_l3_flagmux, + .num_modules = ARRAY_SIZE(omap5_l3_flagmux), + .l3_masters = omap_l3_masters, + .num_masters = ARRAY_SIZE(omap_l3_masters), + /* The 6 MSBs of register field used to distinguish initiator */ + .mst_addr_mask = 0x7E0, +}; + /* DRA7 data */ static struct l3_target_data dra_l3_target_data_clk1[] = { {0x2a00, "AES1",},
The L3 Error handling on OMAP5 for the most part is very similar to that of OMAP4, and had leveraged common data structures and register layout definitions so far. Upon closer inspection, there are a few minor differences causing an incorrect decoding and reporting of the master NIU upon an error: 1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies 11 bits on OMAP5 as against 8 bits on OMAP4, with the master NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR field. 2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3 input sources on OMAP5. The common DEBUGSS source is at a different input on each SoC. Fix the above issues by using a OMAP5-specific compatible property and using SoC-specific data where there are differences. Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> --- Some validation traces by adding couple of traces and intentionally creating L3 errors from DSP & IPU by accessing invalid Timers Before Patch: OMAP4 [Correct] IPU accessing Timer4 [ 46.548095] flagmux = 1, err_reg = 0x8000 err_src = 0xf [ 46.553344] mstaddr = 0x44 mask = 0xfc masterid = 0x11 [ 46.553955] ------------[ cut here ]------------ [ 46.563171] WARNING: CPU: 0 PID: 4 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 46.564941] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during Functional access DSP accessing Timer5: [ 114.018524] flagmux = 0, err_reg = 0x4 err_src = 0x2 [ 114.023498] mstaddr = 0x20 mask = 0xfc masterid = 0x8 [ 114.028564] ------------[ cut here ]------------ [ 114.033233] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 114.042572] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional access OMAP5 [Incorrect] IPU accessing Timer4: [ 29.579306] flagmux = 1, err_reg = 0x8000 err_src = 0xf [ 29.584550] mstaddr = 0x220 mask = 0xfc masterid = 0x8 [ 29.589705] ------------[ cut here ]------------ [ 29.594345] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 29.603774] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET L4PER3 (Idle): Data Access in User mode during Functional access DSP accessing Timer5: [ 21.347105] flagmux = 0, err_reg = 0x4 err_src = 0x2 [ 21.352091] mstaddr = 0x100 mask = 0xfc masterid = 0x0 [ 21.357250] ------------[ cut here ]------------ [ 21.361896] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 21.371242] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET ABE (Idle): Data Access in Supervisor mode during Functional access After Patch: OMAP4 same as above OMAP5 [Corrected] IPU accessing Timer4 [ 67.896693] flagmux = 1, err_reg = 0x8000 err_src = 0xf [ 67.901940] mstaddr = 0x220 mask = 0x7e0 masterid = 0x11 [ 67.907275] ------------[ cut here ]------------ [ 67.911924] WARNING: CPU: 0 PID: 61 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 67.921357] 44000000.ocp:L3 Custom Error: MASTER DucatiM3 TARGET L4PER3 (Idle): Data Access in User mode during Functional access DSP accessing Timer5 [ 24.452565] flagmux = 0, err_reg = 0x4 err_src = 0x2 [ 24.457552] mstaddr = 0x100 mask = 0x7e0 masterid = 0x8 [ 24.462798] ------------[ cut here ]------------ [ 24.467449] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:149 l3_interrupt_handler+0x280/0x388() [ 24.476795] 44000000.ocp:L3 Custom Error: MASTER DSP TARGET ABE (Idle): Data Access in Supervisor mode during Functional access .../devicetree/bindings/arm/omap/l3-noc.txt | 1 + arch/arm/boot/dts/omap5.dtsi | 2 +- drivers/bus/omap_l3_noc.c | 5 ++- drivers/bus/omap_l3_noc.h | 52 ++++++++++++++++------ 4 files changed, 44 insertions(+), 16 deletions(-)