| Message ID | 2fa8c45a15acc7fdcf75611d46530a643858115d.1435646447.git.maitysanchayan@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 2015-06-30 08:54, Sanchayan Maity wrote: > Add device tree node for touchscreen support on Colibri VF50. The > touchscreen functionality on VF50 uses the ADC channels of Vybrid > and some GPIOs. Also add pinctrl nodes for proper pinmux. > > Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> > --- > arch/arm/boot/dts/vf500-colibri-eval-v3.dts | 4 +++ > arch/arm/boot/dts/vf500-colibri.dtsi | 46 +++++++++++++++++++++++++++++ > 2 files changed, 50 insertions(+) > > diff --git a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts > b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts > index 7fc782c..c5efb57 100644 > --- a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts > +++ b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts > @@ -15,3 +15,7 @@ > model = "Toradex Colibri VF50 on Colibri Evaluation Board"; > compatible = "toradex,vf500-colibri_vf50-on-eval", > "toradex,vf500-colibri_vf50", "fsl,vf500"; > }; > + > +&touchctrl { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi > b/arch/arm/boot/dts/vf500-colibri.dtsi > index cee34a3..4807a32 100644 > --- a/arch/arm/boot/dts/vf500-colibri.dtsi > +++ b/arch/arm/boot/dts/vf500-colibri.dtsi > @@ -17,4 +17,50 @@ > memory { > reg = <0x80000000 0x8000000>; > }; > + > + touchctrl: vf50_touchctrl { > + compatible = "toradex,vf50-touchctrl"; > + io-channels = <&adc1 0>,<&adc0 0>, > + <&adc0 1>,<&adc1 2>; > + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; > + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; > + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; > + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; > + pen-detect-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; > + pen-pullup-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "idle","default","gpios"; > + pinctrl-0 = <&pinctrl_touchctrl_idle>; > + pinctrl-1 = <&pinctrl_touchctrl_default>; > + pinctrl-2 = <&pinctrl_touchctrl_gpios>; > + status = "disabled"; > + }; > +}; > + > +&iomuxc { > + vf610-colibri { > + pinctrl_touchctrl_idle: touchctrl_idle { > + fsl,pins = < > + VF610_PAD_PTA18__GPIO_8 0x206d I think the detect pin should be in Hi-Z, not be pulled up. Probably the resistance over the plates is much smaller on pen down, hence it doesn't matter too much. > + VF610_PAD_PTA19__GPIO_9 0x206d > + >; > + }; > + > + pinctrl_touchctrl_default: touchctrl_default { > + fsl,pins = < > + VF610_PAD_PTA18__ADC0_SE0 0x2060 > + VF610_PAD_PTA19__ADC0_SE1 0x2060 > + VF610_PAD_PTA16__ADC1_SE0 0x2060 > + VF610_PAD_PTB2__ADC1_SE2 0x2060 > + >; > + }; > + > + pinctrl_touchctrl_gpios: touchctrl_gpios { > + fsl,pins = < > + VF610_PAD_PTA23__GPIO_13 0x22ed > + VF610_PAD_PTB23__GPIO_93 0x22ed > + VF610_PAD_PTA22__GPIO_12 0x22ed > + VF610_PAD_PTA11__GPIO_4 0x22ed > + >; > + }; Hm, those have pull-ups on too, since you set them as output in the drivers open function, I don't think this is necessary. > + }; > }; -- Stefan -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts index 7fc782c..c5efb57 100644 --- a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts +++ b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts @@ -15,3 +15,7 @@ model = "Toradex Colibri VF50 on Colibri Evaluation Board"; compatible = "toradex,vf500-colibri_vf50-on-eval", "toradex,vf500-colibri_vf50", "fsl,vf500"; }; + +&touchctrl { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi index cee34a3..4807a32 100644 --- a/arch/arm/boot/dts/vf500-colibri.dtsi +++ b/arch/arm/boot/dts/vf500-colibri.dtsi @@ -17,4 +17,50 @@ memory { reg = <0x80000000 0x8000000>; }; + + touchctrl: vf50_touchctrl { + compatible = "toradex,vf50-touchctrl"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + pen-detect-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + pen-pullup-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + pinctrl-names = "idle","default","gpios"; + pinctrl-0 = <&pinctrl_touchctrl_idle>; + pinctrl-1 = <&pinctrl_touchctrl_default>; + pinctrl-2 = <&pinctrl_touchctrl_gpios>; + status = "disabled"; + }; +}; + +&iomuxc { + vf610-colibri { + pinctrl_touchctrl_idle: touchctrl_idle { + fsl,pins = < + VF610_PAD_PTA18__GPIO_8 0x206d + VF610_PAD_PTA19__GPIO_9 0x206d + >; + }; + + pinctrl_touchctrl_default: touchctrl_default { + fsl,pins = < + VF610_PAD_PTA18__ADC0_SE0 0x2060 + VF610_PAD_PTA19__ADC0_SE1 0x2060 + VF610_PAD_PTA16__ADC1_SE0 0x2060 + VF610_PAD_PTB2__ADC1_SE2 0x2060 + >; + }; + + pinctrl_touchctrl_gpios: touchctrl_gpios { + fsl,pins = < + VF610_PAD_PTA23__GPIO_13 0x22ed + VF610_PAD_PTB23__GPIO_93 0x22ed + VF610_PAD_PTA22__GPIO_12 0x22ed + VF610_PAD_PTA11__GPIO_4 0x22ed + >; + }; + }; };
Add device tree node for touchscreen support on Colibri VF50. The touchscreen functionality on VF50 uses the ADC channels of Vybrid and some GPIOs. Also add pinctrl nodes for proper pinmux. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> --- arch/arm/boot/dts/vf500-colibri-eval-v3.dts | 4 +++ arch/arm/boot/dts/vf500-colibri.dtsi | 46 +++++++++++++++++++++++++++++ 2 files changed, 50 insertions(+)