| Message ID | 1438931991-17044-3-git-send-email-leilk.liu@mediatek.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | a568231f463225eb31593f71446a267a03ae0528 |
| Headers | show |
Hi Leilk, On Fri, Aug 7, 2015 at 3:19 PM, <leilk.liu@mediatek.com> wrote: > This patch adds basic spi bus for MT8173. > > Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> > > --- > Change in this patch: > 1. change "pad-select" to "mediatek,pad-select". > 2. modify clk relevant implement. > --- > drivers/spi/Kconfig | 9 + > drivers/spi/Makefile | 1 + > drivers/spi/spi-mt65xx.c | 749 +++++++++++++++++++++++++++++++ > include/linux/platform_data/spi-mt65xx.h | 22 + > 4 files changed, 781 insertions(+) > create mode 100644 drivers/spi/spi-mt65xx.c > create mode 100644 include/linux/platform_data/spi-mt65xx.h > > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig > index 0cae169..38ddfba 100644 > --- a/drivers/spi/Kconfig > +++ b/drivers/spi/Kconfig > @@ -326,6 +326,15 @@ config SPI_MESON_SPIFC > This enables master mode support for the SPIFC (SPI flash > controller) available in Amlogic Meson SoCs. > > +config SPI_MT65XX > + tristate "MediaTek SPI controller" > + depends on ARCH_MEDIATEK || COMPILE_TEST > + help > + This selects the MediaTek(R) SPI bus driver. > + If you want to use MediaTek(R) SPI interface, > + say Y or M here.If you are not sure, say N. > + SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs. > + > config SPI_OC_TINY > tristate "OpenCores tiny SPI" > depends on GPIOLIB || COMPILE_TEST > diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile > index 1154dba..9746beb2 100644 > --- a/drivers/spi/Makefile > +++ b/drivers/spi/Makefile > @@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o > obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o > obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o > obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o > +obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o > obj-$(CONFIG_SPI_MXS) += spi-mxs.o > obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o > obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o > diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c > new file mode 100644 > index 0000000..4676b01 > --- /dev/null > +++ b/drivers/spi/spi-mt65xx.c > @@ -0,0 +1,749 @@ > +/* > + * Copyright (c) 2015 MediaTek Inc. > + * Author: Leilk Liu <leilk.liu@mediatek.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/clk.h> > +#include <linux/device.h> > +#include <linux/err.h> > +#include <linux/interrupt.h> Since you are using readl/writel, please import linux/io.h as well (it is implicitly imported by spi/spi.h, but better be safe...) > +#include <linux/ioport.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/platform_data/spi-mt65xx.h> > +#include <linux/pm_runtime.h> > +#include <linux/spi/spi.h> > + > +#define SPI_CFG0_REG 0x0000 > +#define SPI_CFG1_REG 0x0004 > +#define SPI_TX_SRC_REG 0x0008 > +#define SPI_RX_DST_REG 0x000c > +#define SPI_TX_DATA_REG 0x0010 > +#define SPI_RX_DATA_REG 0x0014 > +#define SPI_CMD_REG 0x0018 > +#define SPI_STATUS0_REG 0x001c > +#define SPI_PAD_SEL_REG 0x0024 > + > +#define SPI_CFG0_SCK_HIGH_OFFSET 0 > +#define SPI_CFG0_SCK_LOW_OFFSET 8 > +#define SPI_CFG0_CS_HOLD_OFFSET 16 > +#define SPI_CFG0_CS_SETUP_OFFSET 24 > + > +#define SPI_CFG1_CS_IDLE_OFFSET 0 > +#define SPI_CFG1_PACKET_LOOP_OFFSET 8 > +#define SPI_CFG1_PACKET_LENGTH_OFFSET 16 > +#define SPI_CFG1_GET_TICK_DLY_OFFSET 30 > + > +#define SPI_CFG1_CS_IDLE_MASK 0xff > +#define SPI_CFG1_PACKET_LOOP_MASK 0xff00 > +#define SPI_CFG1_PACKET_LENGTH_MASK 0x3ff0000 > + > +#define SPI_CMD_ACT_OFFSET 0 > +#define SPI_CMD_RESUME_OFFSET 1 > +#define SPI_CMD_CPHA_OFFSET 8 > +#define SPI_CMD_CPOL_OFFSET 9 > +#define SPI_CMD_TXMSBF_OFFSET 12 > +#define SPI_CMD_RXMSBF_OFFSET 13 > +#define SPI_CMD_RX_ENDIAN_OFFSET 14 > +#define SPI_CMD_TX_ENDIAN_OFFSET 15 It feels error-prone that you are defining these offsets here, then redefining the bits just below. Looking at the code, I think it's better if you remove these SPI_CMD_*_OFFSET defines, and only use the BIT(x) defines below. > +#define SPI_CMD_RST BIT(2) > +#define SPI_CMD_PAUSE_EN BIT(4) > +#define SPI_CMD_DEASSERT BIT(5) > +#define SPI_CMD_CPHA BIT(8) > +#define SPI_CMD_CPOL BIT(9) > +#define SPI_CMD_RX_DMA BIT(10) > +#define SPI_CMD_TX_DMA BIT(11) > +#define SPI_CMD_TXMSBF BIT(12) > +#define SPI_CMD_RXMSBF BIT(13) > +#define SPI_CMD_RX_ENDIAN BIT(14) > +#define SPI_CMD_TX_ENDIAN BIT(15) > +#define SPI_CMD_FINISH_IE BIT(16) > +#define SPI_CMD_PAUSE_IE BIT(17) > + > +#define MTK_SPI_QUIRK_PAD_SELECT 1 > +/* Must explicitly send dummy Tx bytes to do Rx only transfer */ > +#define MTK_SPI_QUIRK_MUST_TX 1 > + > +#define MT8173_SPI_MAX_PAD_SEL 3 > + > +#define MTK_SPI_IDLE 0 > +#define MTK_SPI_PAUSED 1 > + > +#define MTK_SPI_MAX_FIFO_SIZE 32 > +#define MTK_SPI_PACKET_SIZE 1024 > + > +struct mtk_spi_compatible { > + u32 need_pad_sel; > + u32 must_tx; Since the quirks are true/false, define these as bool, and remove MTK_SPI_QUIRK_PAD_SELECT/MTK_SPI_QUIRK_MUST_TX. Move the comment here too. > +}; > + > +struct mtk_spi { > + void __iomem *base; > + u32 state; > + u32 pad_sel; > + struct clk *spi_clk, *parent_clk; > + struct spi_transfer *cur_transfer; > + u32 xfer_len; > + struct scatterlist *tx_sgl, *rx_sgl; > + u32 tx_sgl_len, rx_sgl_len; > + const struct mtk_spi_compatible *dev_comp; > +}; > + > +static const struct mtk_spi_compatible mt6589_compat = { > + .need_pad_sel = 0, > + .must_tx = 0, > +}; > + > +static const struct mtk_spi_compatible mt8135_compat = { > + .need_pad_sel = 0, > + .must_tx = 0, > +}; You don't need to set these explicitly to 0/false. > + > +static const struct mtk_spi_compatible mt8173_compat = { > + .need_pad_sel = MTK_SPI_QUIRK_PAD_SELECT, > + .must_tx = MTK_SPI_QUIRK_MUST_TX, Then you can set those as "true". > +}; > + > +/* > + * A piece of default chip info unless the platform > + * supplies it. > + */ > +static const struct mtk_chip_config mtk_default_chip_info = { > + .rx_mlsb = 1, > + .tx_mlsb = 1, > + .tx_endian = 0, > + .rx_endian = 0, > +}; > + > +static const struct of_device_id mtk_spi_of_match[] = { > + { .compatible = "mediatek,mt6589-spi", .data = (void *)&mt6589_compat }, > + { .compatible = "mediatek,mt8135-spi", .data = (void *)&mt8135_compat }, > + { .compatible = "mediatek,mt8173-spi", .data = (void *)&mt8173_compat }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, mtk_spi_of_match); > + > +static void mtk_spi_reset(struct mtk_spi *mdata) > +{ > + u32 reg_val; > + > + /* set the software reset bit in SPI_CMD_REG. */ > + reg_val = readl(mdata->base + SPI_CMD_REG); > + reg_val |= SPI_CMD_RST; > + writel(reg_val, mdata->base + SPI_CMD_REG); > + > + reg_val = readl(mdata->base + SPI_CMD_REG); > + reg_val &= ~SPI_CMD_RST; > + writel(reg_val, mdata->base + SPI_CMD_REG); > +} > + > +static void mtk_spi_config(struct mtk_spi *mdata, > + struct mtk_chip_config *chip_config) > +{ > + u32 reg_val; > + > + reg_val = readl(mdata->base + SPI_CMD_REG); > + > + /* set the mlsbx and mlsbtx */ > + reg_val &= ~(SPI_CMD_TXMSBF | SPI_CMD_RXMSBF); > + reg_val |= (chip_config->tx_mlsb << SPI_CMD_TXMSBF_OFFSET); > + reg_val |= (chip_config->rx_mlsb << SPI_CMD_RXMSBF_OFFSET); > + > + /* set the tx/rx endian */ > + reg_val &= ~(SPI_CMD_TX_ENDIAN | SPI_CMD_RX_ENDIAN); > + reg_val |= (chip_config->tx_endian << SPI_CMD_TX_ENDIAN_OFFSET); > + reg_val |= (chip_config->rx_endian << SPI_CMD_RX_ENDIAN_OFFSET); > + > + /* set finish and pause interrupt always enable */ > + reg_val |= SPI_CMD_FINISH_IE | SPI_CMD_PAUSE_EN; > + > + /* disable dma mode */ > + reg_val &= ~(SPI_CMD_TX_DMA | SPI_CMD_RX_DMA); > + > + /* disable deassert mode */ > + reg_val &= ~SPI_CMD_DEASSERT; > + > + writel(reg_val, mdata->base + SPI_CMD_REG); > + > + /* pad select */ > + if (mdata->dev_comp->need_pad_sel) > + writel(mdata->pad_sel, mdata->base + SPI_PAD_SEL_REG); > +} > + > +static int mtk_spi_prepare_hardware(struct spi_master *master) > +{ > + struct spi_transfer *trans; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + struct spi_message *msg = master->cur_msg; > + int ret; > + > + ret = clk_prepare_enable(mdata->spi_clk); > + if (ret < 0) { > + dev_err(&master->dev, "failed to enable clock (%d)\n", ret); > + return ret; > + } > + > + trans = list_first_entry(&msg->transfers, struct spi_transfer, > + transfer_list); > + if (trans->cs_change == 0) { !trans->cs_change > + mdata->state = MTK_SPI_IDLE; > + mtk_spi_reset(mdata); > + } > + > + return ret; > +} > + > +static int mtk_spi_unprepare_hardware(struct spi_master *master) > +{ > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + clk_disable_unprepare(mdata->spi_clk); > + > + return 0; > +} In this case, prepare_hardware/unprepare_hardware is redundant with pm_runtime (apart from the cs_change check, possibly). If PM_RUNTIME is disabled, leave the clock enabled all the time, if not enable/disable in pm_runtime functions (as you already do) See https://git.kernel.org/cgit/linux/kernel/git/broonie/spi.git/commit/?id=db91841b58f9ad0ecbb81ed0fa496c3a1b67fd63 "spi/omap100k: Convert to runtime PM" for an example (it's one of the last driver that used prepare/unprepare calls, and got converted to pm_runtime) > +static int mtk_spi_prepare_message(struct spi_master *master, > + struct spi_message *msg) > +{ > + u32 reg_val; > + u8 cpha, cpol; > + struct mtk_chip_config *chip_config; > + struct spi_device *spi = msg->spi; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + cpha = spi->mode & SPI_CPHA ? 1 : 0; > + cpol = spi->mode & SPI_CPOL ? 1 : 0; > + > + reg_val = readl(mdata->base + SPI_CMD_REG); > + reg_val &= ~(SPI_CMD_CPHA | SPI_CMD_CPOL); > + reg_val |= (cpha << SPI_CMD_CPHA_OFFSET); > + reg_val |= (cpol << SPI_CMD_CPOL_OFFSET); This can actually be simplified a bit by using SPI_CMD_CPHA/SPI_CMD_CPOL instead. > + writel(reg_val, mdata->base + SPI_CMD_REG); > + > + chip_config = spi->controller_data; > + if (!chip_config) { > + chip_config = (void *)&mtk_default_chip_info; > + spi->controller_data = chip_config; > + } > + mtk_spi_config(mdata, chip_config); > + > + return 0; > +} > + > +static void mtk_spi_set_cs(struct spi_device *spi, bool enable) > +{ > + u32 reg_val; > + struct mtk_spi *mdata = spi_master_get_devdata(spi->master); > + > + reg_val = readl(mdata->base + SPI_CMD_REG); > + if (!enable) > + reg_val |= SPI_CMD_PAUSE_EN; > + else > + reg_val &= ~SPI_CMD_PAUSE_EN; > + writel(reg_val, mdata->base + SPI_CMD_REG); > +} > + > +static void mtk_spi_prepare_transfer(struct spi_master *master, > + struct spi_transfer *xfer) > +{ > + u32 spi_clk_hz, div, high_time, low_time, holdtime, > + setuptime, cs_idletime, reg_val = 0; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + spi_clk_hz = clk_get_rate(mdata->spi_clk); > + if (xfer->speed_hz < spi_clk_hz / 2) > + div = DIV_ROUND_UP(spi_clk_hz, xfer->speed_hz); > + else > + div = 1; > + > + high_time = (div + 1) / 2; > + low_time = (div + 1) / 2; > + holdtime = (div + 1) / 2 * 2; > + setuptime = (div + 1) / 2 * 2; > + cs_idletime = (div + 1) / 2 * 2; Why setting variables with the exact same value? Can you do with just 2? > + reg_val |= (((high_time - 1) & 0xff) << SPI_CFG0_SCK_HIGH_OFFSET); > + reg_val |= (((low_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET); > + reg_val |= (((holdtime - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET); > + reg_val |= (((setuptime - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET); Not sure of the details, but can you guarantee this will never overflow? I.e. can div be larger than 256? > + writel(reg_val, mdata->base + SPI_CFG0_REG); > + > + reg_val = readl(mdata->base + SPI_CFG1_REG); > + reg_val &= ~SPI_CFG1_CS_IDLE_MASK; > + reg_val |= (((cs_idletime - 1) & 0xff) << SPI_CFG1_CS_IDLE_OFFSET); > + writel(reg_val, mdata->base + SPI_CFG1_REG); > +} > + > +static void mtk_spi_setup_packet(struct spi_master *master) > +{ > + u32 packet_size, packet_loop, reg_val; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + packet_size = min_t(unsigned, mdata->xfer_len, MTK_SPI_PACKET_SIZE); u32 instead of unsigned. > + packet_loop = mdata->xfer_len / packet_size; > + > + reg_val = readl(mdata->base + SPI_CFG1_REG); > + reg_val &= ~(SPI_CFG1_PACKET_LENGTH_MASK + SPI_CFG1_PACKET_LOOP_MASK); Use |, not +. > + reg_val |= (packet_size - 1) << SPI_CFG1_PACKET_LENGTH_OFFSET; > + reg_val |= (packet_loop - 1) << SPI_CFG1_PACKET_LOOP_OFFSET; Can packet_loop be >256? > + writel(reg_val, mdata->base + SPI_CFG1_REG); > +} > + > +static void mtk_spi_enable_transfer(struct spi_master *master) > +{ > + int cmd; u32 > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + cmd = readl(mdata->base + SPI_CMD_REG); > + if (mdata->state == MTK_SPI_IDLE) > + cmd |= 1 << SPI_CMD_ACT_OFFSET; > + else > + cmd |= 1 << SPI_CMD_RESUME_OFFSET; > + writel(cmd, mdata->base + SPI_CMD_REG); > +} > + > +static int mtk_spi_get_mult_delta(int xfer_len) xfer_len is a u32, so should be mult_delta. > +{ > + int mult_delta; > + > + if (xfer_len > MTK_SPI_PACKET_SIZE) > + mult_delta = xfer_len % MTK_SPI_PACKET_SIZE; > + else > + mult_delta = 0; > + > + return mult_delta; > +} > + > +static void mtk_spi_update_mdata_len(struct spi_master *master) > +{ > + int mult_delta; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + if (mdata->tx_sgl_len && mdata->rx_sgl_len) { > + if (mdata->tx_sgl_len > mdata->rx_sgl_len) { > + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); > + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; > + mdata->rx_sgl_len = mult_delta; > + mdata->tx_sgl_len -= mdata->xfer_len; > + } else { > + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); > + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; > + mdata->tx_sgl_len = mult_delta; > + mdata->rx_sgl_len -= mdata->xfer_len; > + } > + } else if (mdata->tx_sgl_len) { > + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); > + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; > + mdata->tx_sgl_len = mult_delta; > + } else if (mdata->rx_sgl_len) { > + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); > + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; > + mdata->rx_sgl_len = mult_delta; > + } > +} > + > +static void mtk_spi_setup_dma_addr(struct spi_master *master, > + struct spi_transfer *xfer) > +{ > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + if (mdata->tx_sgl) > + writel(cpu_to_le32(xfer->tx_dma), mdata->base + SPI_TX_SRC_REG); > + if (mdata->rx_sgl) > + writel(cpu_to_le32(xfer->rx_dma), mdata->base + SPI_RX_DST_REG); > +} > + > +static int mtk_spi_fifo_transfer(struct spi_master *master, > + struct spi_device *spi, > + struct spi_transfer *xfer) > +{ > + int cnt, i; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + mdata->cur_transfer = xfer; > + mdata->xfer_len = xfer->len; > + mtk_spi_prepare_transfer(master, xfer); > + mtk_spi_setup_packet(master); > + > + if (xfer->len % 4) > + cnt = xfer->len / 4 + 1; > + else > + cnt = xfer->len / 4; > + > + for (i = 0; i < cnt; i++) > + writel(*((u32 *)xfer->tx_buf + i), This will access past the end of tx_buf if len%4 > 0. > + mdata->base + SPI_TX_DATA_REG); > + > + mtk_spi_enable_transfer(master); > + > + return 1; > +} > + > +static int mtk_spi_dma_transfer(struct spi_master *master, > + struct spi_device *spi, > + struct spi_transfer *xfer) > +{ > + int cmd; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + mdata->tx_sgl = NULL; > + mdata->rx_sgl = NULL; > + mdata->tx_sgl_len = 0; > + mdata->rx_sgl_len = 0; > + mdata->cur_transfer = xfer; > + > + mtk_spi_prepare_transfer(master, xfer); > + > + cmd = readl(mdata->base + SPI_CMD_REG); > + if (xfer->tx_buf) > + cmd |= SPI_CMD_TX_DMA; > + if (xfer->rx_buf) > + cmd |= SPI_CMD_RX_DMA; > + writel(cmd, mdata->base + SPI_CMD_REG); > + > + if (xfer->tx_buf) > + mdata->tx_sgl = xfer->tx_sg.sgl; > + if (xfer->rx_buf) > + mdata->rx_sgl = xfer->rx_sg.sgl; > + > + if (mdata->tx_sgl) { > + xfer->tx_dma = sg_dma_address(mdata->tx_sgl); > + mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl); > + } > + if (mdata->rx_sgl) { > + xfer->rx_dma = sg_dma_address(mdata->rx_sgl); > + mdata->rx_sgl_len = sg_dma_len(mdata->rx_sgl); > + } > + > + mtk_spi_update_mdata_len(master); > + mtk_spi_setup_packet(master); > + mtk_spi_setup_dma_addr(master, xfer); > + mtk_spi_enable_transfer(master); > + > + return 1; > +} > + > +static int mtk_spi_transfer_one(struct spi_master *master, > + struct spi_device *spi, > + struct spi_transfer *xfer) > +{ > + if (master->can_dma(master, spi, xfer)) > + return mtk_spi_dma_transfer(master, spi, xfer); > + else > + return mtk_spi_fifo_transfer(master, spi, xfer); > +} > + > +static bool mtk_spi_can_dma(struct spi_master *master, > + struct spi_device *spi, > + struct spi_transfer *xfer) > +{ > + return xfer->len > MTK_SPI_MAX_FIFO_SIZE; > +} > + > +static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id) > +{ > + u32 cmd, reg_val, i; > + struct spi_master *master = dev_id; > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + struct spi_transfer *trans = mdata->cur_transfer; > + > + reg_val = readl(mdata->base + SPI_STATUS0_REG); > + if (reg_val & 0x2) define 0x2? > + mdata->state = MTK_SPI_PAUSED; > + else > + mdata->state = MTK_SPI_IDLE; > + > + if (!master->can_dma(master, master->cur_msg->spi, trans)) { > + /* xfer len is not N*4 bytes every time in a transfer, > + * but SPI_RX_DATA_REG must reads 4 bytes once, > + * so rx buffer byte by byte. > + */ > + if (trans->rx_buf) { > + for (i = 0; i < mdata->xfer_len; i++) { > + if (i % 4 == 0) > + reg_val = > + readl(mdata->base + SPI_RX_DATA_REG); Strange indentation. Might be better to put readl on the same line, and SPI_RX_DATA_REG on the next one. > + *((u8 *)(trans->rx_buf + i)) = > + (reg_val >> ((i % 4) * 8)) & 0xff; This feels a bit awkward... Also, & 0xff is not needed. > + } > + } > + spi_finalize_current_transfer(master); > + return IRQ_HANDLED; > + } > + > + if (mdata->tx_sgl) > + trans->tx_dma += mdata->xfer_len; > + if (mdata->rx_sgl) > + trans->rx_dma += mdata->xfer_len; > + > + if (mdata->tx_sgl && (mdata->tx_sgl_len == 0)) { > + mdata->tx_sgl = sg_next(mdata->tx_sgl); > + if (mdata->tx_sgl) { > + trans->tx_dma = sg_dma_address(mdata->tx_sgl); > + mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl); > + } > + } > + if (mdata->rx_sgl && (mdata->rx_sgl_len == 0)) { > + mdata->rx_sgl = sg_next(mdata->rx_sgl); > + if (mdata->rx_sgl) { > + trans->rx_dma = sg_dma_address(mdata->rx_sgl); > + mdata->rx_sgl_len = sg_dma_len(mdata->rx_sgl); > + } > + } > + > + if (!mdata->tx_sgl && !mdata->rx_sgl) { > + /* spi disable dma */ > + cmd = readl(mdata->base + SPI_CMD_REG); > + cmd &= ~SPI_CMD_TX_DMA; > + cmd &= ~SPI_CMD_RX_DMA; > + writel(cmd, mdata->base + SPI_CMD_REG); > + > + spi_finalize_current_transfer(master); > + return IRQ_HANDLED; > + } > + > + mtk_spi_update_mdata_len(master); > + mtk_spi_setup_packet(master); > + mtk_spi_setup_dma_addr(master, trans); > + mtk_spi_enable_transfer(master); > + > + return IRQ_HANDLED; > +} > + > +static int mtk_spi_probe(struct platform_device *pdev) > +{ > + struct spi_master *master; > + struct mtk_spi *mdata; > + const struct of_device_id *of_id; > + struct resource *res; > + int irq, ret; Space, not tab, between int and irq. > + > + master = spi_alloc_master(&pdev->dev, sizeof(*mdata)); > + if (!master) { > + dev_err(&pdev->dev, "failed to alloc spi master\n"); > + return -ENOMEM; > + } > + > + master->auto_runtime_pm = true; > + master->dev.of_node = pdev->dev.of_node; > + master->mode_bits = SPI_CPOL | SPI_CPHA; > + > + master->set_cs = mtk_spi_set_cs; > + master->prepare_transfer_hardware = mtk_spi_prepare_hardware; > + master->unprepare_transfer_hardware = mtk_spi_unprepare_hardware; > + master->prepare_message = mtk_spi_prepare_message; > + master->transfer_one = mtk_spi_transfer_one; > + master->can_dma = mtk_spi_can_dma; > + > + of_id = of_match_node(mtk_spi_of_match, pdev->dev.of_node); > + if (!of_id) { > + dev_err(&pdev->dev, "failed to probe of_node\n"); > + ret = -EINVAL; > + goto err_put_master; > + } > + > + mdata = spi_master_get_devdata(master); > + mdata->dev_comp = of_id->data; > + if (mdata->dev_comp->must_tx) > + master->flags = SPI_MASTER_MUST_TX; > + > + if (mdata->dev_comp->need_pad_sel) { > + ret = of_property_read_u32(pdev->dev.of_node, > + "mediatek,pad-select", > + &mdata->pad_sel); > + if (ret) { > + dev_err(&pdev->dev, "failed to read pad select: %d\n", > + ret); > + goto err_put_master; > + } > + > + if (mdata->pad_sel > MT8173_SPI_MAX_PAD_SEL) { > + dev_err(&pdev->dev, "wrong pad-select: %u\n", > + mdata->pad_sel); > + ret = -EINVAL; > + goto err_put_master; > + } > + } > + > + platform_set_drvdata(pdev, master); > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!res) { > + ret = -ENODEV; > + dev_err(&pdev->dev, "failed to determine base address\n"); > + goto err_put_master; > + } > + > + mdata->base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(mdata->base)) { > + ret = PTR_ERR(mdata->base); > + goto err_put_master; > + } > + > + irq = platform_get_irq(pdev, 0); > + if (irq < 0) { > + dev_err(&pdev->dev, "failed to get irq (%d)\n", irq); > + ret = irq; > + goto err_put_master; > + } > + > + if (!pdev->dev.dma_mask) > + pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; > + > + ret = devm_request_irq(&pdev->dev, irq, mtk_spi_interrupt, > + IRQF_TRIGGER_NONE, dev_name(&pdev->dev), master); > + if (ret) { > + dev_err(&pdev->dev, "failed to register irq (%d)\n", ret); > + goto err_put_master; > + } > + > + mdata->spi_clk = devm_clk_get(&pdev->dev, "spi-clk"); > + if (IS_ERR(mdata->spi_clk)) { > + ret = PTR_ERR(mdata->spi_clk); > + dev_err(&pdev->dev, "failed to get spi-clk: %d\n", ret); > + goto err_put_master; > + } > + > + mdata->parent_clk = devm_clk_get(&pdev->dev, "parent-clk"); > + if (IS_ERR(mdata->parent_clk)) { > + ret = PTR_ERR(mdata->parent_clk); > + dev_err(&pdev->dev, "failed to get parent-clk: %d\n", ret); > + goto err_put_master; > + } > + > + ret = clk_prepare_enable(mdata->spi_clk); > + if (ret < 0) { > + dev_err(&pdev->dev, "failed to enable spi_clk (%d)\n", ret); > + goto err_put_master; > + } > + > + ret = clk_set_parent(mdata->spi_clk, mdata->parent_clk); > + if (ret < 0) { > + dev_err(&pdev->dev, "failed to clk_set_parent (%d)\n", ret); > + goto err_disable_clk; > + } > + > + clk_disable_unprepare(mdata->spi_clk); > + > + pm_runtime_enable(&pdev->dev); > + > + ret = devm_spi_register_master(&pdev->dev, master); > + if (ret) { > + dev_err(&pdev->dev, "failed to register master (%d)\n", ret); > + goto err_put_master; > + } > + > + return 0; > + > +err_disable_clk: > + clk_disable_unprepare(mdata->spi_clk); > +err_put_master: > + spi_master_put(master); > + > + return ret; > +} > + > +static int mtk_spi_remove(struct platform_device *pdev) > +{ > + struct spi_master *master = platform_get_drvdata(pdev); > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + pm_runtime_disable(&pdev->dev); > + > + mtk_spi_reset(mdata); > + clk_disable_unprepare(mdata->spi_clk); > + spi_master_put(master); > + > + return 0; > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int mtk_spi_suspend(struct device *dev) > +{ > + int ret; > + struct spi_master *master = dev_get_drvdata(dev); > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + ret = spi_master_suspend(master); > + if (ret) > + return ret; > + > + if (!pm_runtime_suspended(dev)) > + clk_disable_unprepare(mdata->spi_clk); > + > + return ret; > +} > + > +static int mtk_spi_resume(struct device *dev) > +{ > + int ret; > + struct spi_master *master = dev_get_drvdata(dev); > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + if (!pm_runtime_suspended(dev)) { > + ret = clk_prepare_enable(mdata->spi_clk); > + if (ret < 0) > + return ret; > + } > + > + ret = spi_master_resume(master); > + if (ret < 0) > + clk_disable_unprepare(mdata->spi_clk); > + > + return ret; > +} > +#endif /* CONFIG_PM_SLEEP */ > + > +#ifdef CONFIG_PM > +static int mtk_spi_runtime_suspend(struct device *dev) > +{ > + struct spi_master *master = dev_get_drvdata(dev); > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + clk_disable_unprepare(mdata->spi_clk); > + > + return 0; > +} > + > +static int mtk_spi_runtime_resume(struct device *dev) > +{ > + struct spi_master *master = dev_get_drvdata(dev); > + struct mtk_spi *mdata = spi_master_get_devdata(master); > + > + return clk_prepare_enable(mdata->spi_clk); > +} > +#endif /* CONFIG_PM */ > + > +static const struct dev_pm_ops mtk_spi_pm = { > + SET_SYSTEM_SLEEP_PM_OPS(mtk_spi_suspend, mtk_spi_resume) > + SET_RUNTIME_PM_OPS(mtk_spi_runtime_suspend, > + mtk_spi_runtime_resume, NULL) > +}; > + > +struct platform_driver mtk_spi_driver = { > + .driver = { > + .name = "mtk-spi", > + .pm = &mtk_spi_pm, > + .of_match_table = mtk_spi_of_match, > + }, > + .probe = mtk_spi_probe, > + .remove = mtk_spi_remove, > +}; > + > +module_platform_driver(mtk_spi_driver); > + > +MODULE_DESCRIPTION("MTK SPI Controller driver"); > +MODULE_AUTHOR("Leilk Liu <leilk.liu@mediatek.com>"); > +MODULE_LICENSE("GPL v2"); > +MODULE_ALIAS("platform: mtk_spi"); > diff --git a/include/linux/platform_data/spi-mt65xx.h b/include/linux/platform_data/spi-mt65xx.h > new file mode 100644 > index 0000000..7512255 > --- /dev/null > +++ b/include/linux/platform_data/spi-mt65xx.h > @@ -0,0 +1,22 @@ > +/* > + * MTK SPI bus driver definitions > + * > + * Copyright (c) 2015 MediaTek Inc. > + * Author: Leilk Liu <leilk.liu@mediatek.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#ifndef ____LINUX_PLATFORM_DATA_SPI_MTK_H > +#define ____LINUX_PLATFORM_DATA_SPI_MTK_H > + > +/* Board specific platform_data */ > +struct mtk_chip_config { > + u32 tx_mlsb; > + u32 rx_mlsb; > + u32 tx_endian; > + u32 rx_endian; > +}; > +#endif -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, > > +#include <linux/clk.h> > > +#include <linux/device.h> > > +#include <linux/err.h> > > +#include <linux/interrupt.h> > > Since you are using readl/writel, please import linux/io.h as well (it > is implicitly imported by spi/spi.h, but better be safe...) > OK, I'll fix it. > > +#include <linux/ioport.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > + > > +#define SPI_CMD_ACT_OFFSET 0 > > +#define SPI_CMD_RESUME_OFFSET 1 > > +#define SPI_CMD_CPHA_OFFSET 8 > > +#define SPI_CMD_CPOL_OFFSET 9 > > +#define SPI_CMD_TXMSBF_OFFSET 12 > > +#define SPI_CMD_RXMSBF_OFFSET 13 > > +#define SPI_CMD_RX_ENDIAN_OFFSET 14 > > +#define SPI_CMD_TX_ENDIAN_OFFSET 15 > > It feels error-prone that you are defining these offsets here, then > redefining the bits just below. > > Looking at the code, I think it's better if you remove these > SPI_CMD_*_OFFSET defines, and only use the BIT(x) defines below. > OK, I will remove those defines. > > +#define SPI_CMD_RST BIT(2) > > +#define SPI_CMD_PAUSE_EN BIT(4) > > +#define SPI_CMD_DEASSERT BIT(5) > > +#define SPI_CMD_CPHA BIT(8) > > +#define SPI_CMD_CPOL BIT(9) > > +#define SPI_CMD_RX_DMA BIT(10) > > +#define SPI_CMD_TX_DMA BIT(11) > > +#define SPI_CMD_TXMSBF BIT(12) > > +#define SPI_CMD_RXMSBF BIT(13) > > +#define SPI_CMD_RX_ENDIAN BIT(14) > > +#define SPI_CMD_TX_ENDIAN BIT(15) > > +#define SPI_CMD_FINISH_IE BIT(16) > > +#define SPI_CMD_PAUSE_IE BIT(17) > > + > > + > > +struct mtk_spi_compatible { > > + u32 need_pad_sel; > > + u32 must_tx; > > Since the quirks are true/false, define these as bool, and remove > MTK_SPI_QUIRK_PAD_SELECT/MTK_SPI_QUIRK_MUST_TX. Move the comment here > too. > OK. I will fix it. > > +}; > > + > > +static const struct mtk_spi_compatible mt6589_compat = { > > + .need_pad_sel = 0, > > + .must_tx = 0, > > +}; > > + > > +static const struct mtk_spi_compatible mt8135_compat = { > > + .need_pad_sel = 0, > > + .must_tx = 0, > > +}; > > You don't need to set these explicitly to 0/false. > OK, I will fix it. > > + > > +static const struct mtk_spi_compatible mt8173_compat = { > > + .need_pad_sel = MTK_SPI_QUIRK_PAD_SELECT, > > + .must_tx = MTK_SPI_QUIRK_MUST_TX, > > Then you can set those as "true". > OK, I will fix it. > > +}; > > + > > +/* > > + * A piece of default chip info unless the platform > > + * supplies it. > > + */ > > +static const struct mtk_chip_config mtk_default_chip_info = { > > + .rx_mlsb = 1, > > + .tx_mlsb = 1, > > + .tx_endian = 0, > > + .rx_endian = 0, > > +}; > > + > > + > > + trans = list_first_entry(&msg->transfers, struct spi_transfer, > > + transfer_list); > > + if (trans->cs_change == 0) { > > !trans->cs_change > OK, I will fix it. > > + mdata->state = MTK_SPI_IDLE; > > + mtk_spi_reset(mdata); > > + } > > + > > + return ret; > > +} > > + > > +static int mtk_spi_unprepare_hardware(struct spi_master *master) > > +{ > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + clk_disable_unprepare(mdata->spi_clk); > > + > > + return 0; > > +} > > In this case, prepare_hardware/unprepare_hardware is redundant with > pm_runtime (apart from the cs_change check, possibly). > > If PM_RUNTIME is disabled, leave the clock enabled all the time, if > not enable/disable in pm_runtime functions (as you already do) > > See https://git.kernel.org/cgit/linux/kernel/git/broonie/spi.git/commit/?id=db91841b58f9ad0ecbb81ed0fa496c3a1b67fd63 > "spi/omap100k: Convert to runtime PM" for an example (it's one of the > last driver that used prepare/unprepare calls, and got converted to > pm_runtime) > OK, I'll fix it. > > +static int mtk_spi_prepare_message(struct spi_master *master, > > + struct spi_message *msg) > > +{ > > + u32 reg_val; > > + u8 cpha, cpol; > > + struct mtk_chip_config *chip_config; > > + struct spi_device *spi = msg->spi; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + cpha = spi->mode & SPI_CPHA ? 1 : 0; > > + cpol = spi->mode & SPI_CPOL ? 1 : 0; > > + > > + reg_val = readl(mdata->base + SPI_CMD_REG); > > + reg_val &= ~(SPI_CMD_CPHA | SPI_CMD_CPOL); > > + reg_val |= (cpha << SPI_CMD_CPHA_OFFSET); > > + reg_val |= (cpol << SPI_CMD_CPOL_OFFSET); > > This can actually be simplified a bit by using > SPI_CMD_CPHA/SPI_CMD_CPOL instead. > OK, I will fix it. > > + writel(reg_val, mdata->base + SPI_CMD_REG); > > + > > + > > +static void mtk_spi_prepare_transfer(struct spi_master *master, > > + struct spi_transfer *xfer) > > +{ > > + u32 spi_clk_hz, div, high_time, low_time, holdtime, > > + setuptime, cs_idletime, reg_val = 0; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + spi_clk_hz = clk_get_rate(mdata->spi_clk); > > + if (xfer->speed_hz < spi_clk_hz / 2) > > + div = DIV_ROUND_UP(spi_clk_hz, xfer->speed_hz); > > + else > > + div = 1; > > + > > + high_time = (div + 1) / 2; > > + low_time = (div + 1) / 2; > > + holdtime = (div + 1) / 2 * 2; > > + setuptime = (div + 1) / 2 * 2; > > + cs_idletime = (div + 1) / 2 * 2; > > Why setting variables with the exact same value? Can you do with just 2? > OK, I'll fix it. > > + reg_val |= (((high_time - 1) & 0xff) << SPI_CFG0_SCK_HIGH_OFFSET); > > + reg_val |= (((low_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET); > > + reg_val |= (((holdtime - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET); > > + reg_val |= (((setuptime - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET); > > Not sure of the details, but can you guarantee this will never > overflow? I.e. can div be larger than 256? > If xfer->speed_hz is too small, maybe div may be larger than 256, but 0xff will mask div here, so I think it doesn't matter. > > + writel(reg_val, mdata->base + SPI_CFG0_REG); > > + > > + reg_val = readl(mdata->base + SPI_CFG1_REG); > > + reg_val &= ~SPI_CFG1_CS_IDLE_MASK; > > + reg_val |= (((cs_idletime - 1) & 0xff) << SPI_CFG1_CS_IDLE_OFFSET); > > + writel(reg_val, mdata->base + SPI_CFG1_REG); > > +} > > + > > +static void mtk_spi_setup_packet(struct spi_master *master) > > +{ > > + u32 packet_size, packet_loop, reg_val; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + packet_size = min_t(unsigned, mdata->xfer_len, MTK_SPI_PACKET_SIZE); > > u32 instead of unsigned. OK, I will fix it. > > > + packet_loop = mdata->xfer_len / packet_size; > > + > > + reg_val = readl(mdata->base + SPI_CFG1_REG); > > + reg_val &= ~(SPI_CFG1_PACKET_LENGTH_MASK + SPI_CFG1_PACKET_LOOP_MASK); > > Use |, not +. OK, I will fix it. > > > + reg_val |= (packet_size - 1) << SPI_CFG1_PACKET_LENGTH_OFFSET; > > + reg_val |= (packet_loop - 1) << SPI_CFG1_PACKET_LOOP_OFFSET; > > Can packet_loop be >256? > packet_loop can never be >256. If packet_loop=256, the xfer_len will be 256*1024 bytes. It's not possible because packet_loop is from mdata->xfer_len / packet_size, mdata->xfer_len is from sg_dma_len(). > > + writel(reg_val, mdata->base + SPI_CFG1_REG); > > +} > > + > > +static void mtk_spi_enable_transfer(struct spi_master *master) > > +{ > > + int cmd; > > u32 > OK. I will fix it. > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + cmd = readl(mdata->base + SPI_CMD_REG); > > + if (mdata->state == MTK_SPI_IDLE) > > + cmd |= 1 << SPI_CMD_ACT_OFFSET; > > + else > > + cmd |= 1 << SPI_CMD_RESUME_OFFSET; > > + writel(cmd, mdata->base + SPI_CMD_REG); > > +} > > + > > +static int mtk_spi_get_mult_delta(int xfer_len) > > xfer_len is a u32, so should be mult_delta. > OK, I'll fix it. > > +{ > > + int mult_delta; > > + > > + if (xfer_len > MTK_SPI_PACKET_SIZE) > > + mult_delta = xfer_len % MTK_SPI_PACKET_SIZE; > > + else > > + mult_delta = 0; > > + > > + return mult_delta; > > +} > > + > > +static void mtk_spi_update_mdata_len(struct spi_master *master) > > +{ > > + int mult_delta; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + if (mdata->tx_sgl_len && mdata->rx_sgl_len) { > > + if (mdata->tx_sgl_len > mdata->rx_sgl_len) { > > + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); > > + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; > > + mdata->rx_sgl_len = mult_delta; > > + mdata->tx_sgl_len -= mdata->xfer_len; > > + } else { > > + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); > > + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; > > + mdata->tx_sgl_len = mult_delta; > > + mdata->rx_sgl_len -= mdata->xfer_len; > > + } > > + } else if (mdata->tx_sgl_len) { > > + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); > > + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; > > + mdata->tx_sgl_len = mult_delta; > > + } else if (mdata->rx_sgl_len) { > > + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); > > + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; > > + mdata->rx_sgl_len = mult_delta; > > + } > > +} > > + > > +static void mtk_spi_setup_dma_addr(struct spi_master *master, > > + struct spi_transfer *xfer) > > +{ > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + if (mdata->tx_sgl) > > + writel(cpu_to_le32(xfer->tx_dma), mdata->base + SPI_TX_SRC_REG); > > + if (mdata->rx_sgl) > > + writel(cpu_to_le32(xfer->rx_dma), mdata->base + SPI_RX_DST_REG); > > +} > > + > > +static int mtk_spi_fifo_transfer(struct spi_master *master, > > + struct spi_device *spi, > > + struct spi_transfer *xfer) > > +{ > > + int cnt, i; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + mdata->cur_transfer = xfer; > > + mdata->xfer_len = xfer->len; > > + mtk_spi_prepare_transfer(master, xfer); > > + mtk_spi_setup_packet(master); > > + > > + if (xfer->len % 4) > > + cnt = xfer->len / 4 + 1; > > + else > > + cnt = xfer->len / 4; > > + > > + for (i = 0; i < cnt; i++) > > + writel(*((u32 *)xfer->tx_buf + i), > > This will access past the end of tx_buf if len%4 > 0. SPI_TX_DATA_REG requires write 4 bytes once. If len%4 > 0, this just reads more data from dram(xfer->tx_buf) to register, and that spi hw only tranfer length according to xfer->len, so I think it doesn't matter. > > + mdata->base + SPI_TX_DATA_REG); > > + > > + mtk_spi_enable_transfer(master); > > + > > + return 1; > > +} > > + > > +static int mtk_spi_dma_transfer(struct spi_master *master, > > + struct spi_device *spi, > > + struct spi_transfer *xfer) > > +{ > > + int cmd; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + > > + mdata->tx_sgl = NULL; > > + mdata->rx_sgl = NULL; > > + mdata->tx_sgl_len = 0; > > + mdata->rx_sgl_len = 0; > > + mdata->cur_transfer = xfer; > > + > > + mtk_spi_prepare_transfer(master, xfer); > > + > > + cmd = readl(mdata->base + SPI_CMD_REG); > > + if (xfer->tx_buf) > > + cmd |= SPI_CMD_TX_DMA; > > + if (xfer->rx_buf) > > + cmd |= SPI_CMD_RX_DMA; > > + writel(cmd, mdata->base + SPI_CMD_REG); > > + > > + if (xfer->tx_buf) > > + mdata->tx_sgl = xfer->tx_sg.sgl; > > + if (xfer->rx_buf) > > + mdata->rx_sgl = xfer->rx_sg.sgl; > > + > > + if (mdata->tx_sgl) { > > + xfer->tx_dma = sg_dma_address(mdata->tx_sgl); > > + mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl); > > + } > > + if (mdata->rx_sgl) { > > + xfer->rx_dma = sg_dma_address(mdata->rx_sgl); > > + mdata->rx_sgl_len = sg_dma_len(mdata->rx_sgl); > > + } > > + > > + mtk_spi_update_mdata_len(master); > > + mtk_spi_setup_packet(master); > > + mtk_spi_setup_dma_addr(master, xfer); > > + mtk_spi_enable_transfer(master); > > + > > + return 1; > > +} > > + > > +static int mtk_spi_transfer_one(struct spi_master *master, > > + struct spi_device *spi, > > + struct spi_transfer *xfer) > > +{ > > + if (master->can_dma(master, spi, xfer)) > > + return mtk_spi_dma_transfer(master, spi, xfer); > > + else > > + return mtk_spi_fifo_transfer(master, spi, xfer); > > +} > > + > > +static bool mtk_spi_can_dma(struct spi_master *master, > > + struct spi_device *spi, > > + struct spi_transfer *xfer) > > +{ > > + return xfer->len > MTK_SPI_MAX_FIFO_SIZE; > > +} > > + > > +static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id) > > +{ > > + u32 cmd, reg_val, i; > > + struct spi_master *master = dev_id; > > + struct mtk_spi *mdata = spi_master_get_devdata(master); > > + struct spi_transfer *trans = mdata->cur_transfer; > > + > > + reg_val = readl(mdata->base + SPI_STATUS0_REG); > > + if (reg_val & 0x2) > > define 0x2? OK. I will fix it. > > + mdata->state = MTK_SPI_PAUSED; > > + else > > + mdata->state = MTK_SPI_IDLE; > > + > > + if (!master->can_dma(master, master->cur_msg->spi, trans)) { > > + /* xfer len is not N*4 bytes every time in a transfer, > > + * but SPI_RX_DATA_REG must reads 4 bytes once, > > + * so rx buffer byte by byte. > > + */ > > + if (trans->rx_buf) { > > + for (i = 0; i < mdata->xfer_len; i++) { > > + if (i % 4 == 0) > > + reg_val = > > + readl(mdata->base + SPI_RX_DATA_REG); > > Strange indentation. Might be better to put readl on the same line, > and SPI_RX_DATA_REG on the next one. OK. I will fix it. > > + *((u8 *)(trans->rx_buf + i)) = > > + (reg_val >> ((i % 4) * 8)) & 0xff; > > This feels a bit awkward... Also, & 0xff is not needed. > OK, I will fix it. > > + > > +static int mtk_spi_probe(struct platform_device *pdev) > > +{ > > + struct spi_master *master; > > + struct mtk_spi *mdata; > > + const struct of_device_id *of_id; > > + struct resource *res; > > + int irq, ret; > > Space, not tab, between int and irq. > OK. I will fix it. > > + > > + master = spi_alloc_master(&pdev->dev, sizeof(*mdata)); > > + if (!master) { > > + dev_err(&pdev->dev, "failed to alloc spi master\n"); -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 0cae169..38ddfba 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -326,6 +326,15 @@ config SPI_MESON_SPIFC This enables master mode support for the SPIFC (SPI flash controller) available in Amlogic Meson SoCs. +config SPI_MT65XX + tristate "MediaTek SPI controller" + depends on ARCH_MEDIATEK || COMPILE_TEST + help + This selects the MediaTek(R) SPI bus driver. + If you want to use MediaTek(R) SPI interface, + say Y or M here.If you are not sure, say N. + SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs. + config SPI_OC_TINY tristate "OpenCores tiny SPI" depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 1154dba..9746beb2 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o +obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c new file mode 100644 index 0000000..4676b01 --- /dev/null +++ b/drivers/spi/spi-mt65xx.c @@ -0,0 +1,749 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Leilk Liu <leilk.liu@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/platform_data/spi-mt65xx.h> +#include <linux/pm_runtime.h> +#include <linux/spi/spi.h> + +#define SPI_CFG0_REG 0x0000 +#define SPI_CFG1_REG 0x0004 +#define SPI_TX_SRC_REG 0x0008 +#define SPI_RX_DST_REG 0x000c +#define SPI_TX_DATA_REG 0x0010 +#define SPI_RX_DATA_REG 0x0014 +#define SPI_CMD_REG 0x0018 +#define SPI_STATUS0_REG 0x001c +#define SPI_PAD_SEL_REG 0x0024 + +#define SPI_CFG0_SCK_HIGH_OFFSET 0 +#define SPI_CFG0_SCK_LOW_OFFSET 8 +#define SPI_CFG0_CS_HOLD_OFFSET 16 +#define SPI_CFG0_CS_SETUP_OFFSET 24 + +#define SPI_CFG1_CS_IDLE_OFFSET 0 +#define SPI_CFG1_PACKET_LOOP_OFFSET 8 +#define SPI_CFG1_PACKET_LENGTH_OFFSET 16 +#define SPI_CFG1_GET_TICK_DLY_OFFSET 30 + +#define SPI_CFG1_CS_IDLE_MASK 0xff +#define SPI_CFG1_PACKET_LOOP_MASK 0xff00 +#define SPI_CFG1_PACKET_LENGTH_MASK 0x3ff0000 + +#define SPI_CMD_ACT_OFFSET 0 +#define SPI_CMD_RESUME_OFFSET 1 +#define SPI_CMD_CPHA_OFFSET 8 +#define SPI_CMD_CPOL_OFFSET 9 +#define SPI_CMD_TXMSBF_OFFSET 12 +#define SPI_CMD_RXMSBF_OFFSET 13 +#define SPI_CMD_RX_ENDIAN_OFFSET 14 +#define SPI_CMD_TX_ENDIAN_OFFSET 15 + +#define SPI_CMD_RST BIT(2) +#define SPI_CMD_PAUSE_EN BIT(4) +#define SPI_CMD_DEASSERT BIT(5) +#define SPI_CMD_CPHA BIT(8) +#define SPI_CMD_CPOL BIT(9) +#define SPI_CMD_RX_DMA BIT(10) +#define SPI_CMD_TX_DMA BIT(11) +#define SPI_CMD_TXMSBF BIT(12) +#define SPI_CMD_RXMSBF BIT(13) +#define SPI_CMD_RX_ENDIAN BIT(14) +#define SPI_CMD_TX_ENDIAN BIT(15) +#define SPI_CMD_FINISH_IE BIT(16) +#define SPI_CMD_PAUSE_IE BIT(17) + +#define MTK_SPI_QUIRK_PAD_SELECT 1 +/* Must explicitly send dummy Tx bytes to do Rx only transfer */ +#define MTK_SPI_QUIRK_MUST_TX 1 + +#define MT8173_SPI_MAX_PAD_SEL 3 + +#define MTK_SPI_IDLE 0 +#define MTK_SPI_PAUSED 1 + +#define MTK_SPI_MAX_FIFO_SIZE 32 +#define MTK_SPI_PACKET_SIZE 1024 + +struct mtk_spi_compatible { + u32 need_pad_sel; + u32 must_tx; +}; + +struct mtk_spi { + void __iomem *base; + u32 state; + u32 pad_sel; + struct clk *spi_clk, *parent_clk; + struct spi_transfer *cur_transfer; + u32 xfer_len; + struct scatterlist *tx_sgl, *rx_sgl; + u32 tx_sgl_len, rx_sgl_len; + const struct mtk_spi_compatible *dev_comp; +}; + +static const struct mtk_spi_compatible mt6589_compat = { + .need_pad_sel = 0, + .must_tx = 0, +}; + +static const struct mtk_spi_compatible mt8135_compat = { + .need_pad_sel = 0, + .must_tx = 0, +}; + +static const struct mtk_spi_compatible mt8173_compat = { + .need_pad_sel = MTK_SPI_QUIRK_PAD_SELECT, + .must_tx = MTK_SPI_QUIRK_MUST_TX, +}; + +/* + * A piece of default chip info unless the platform + * supplies it. + */ +static const struct mtk_chip_config mtk_default_chip_info = { + .rx_mlsb = 1, + .tx_mlsb = 1, + .tx_endian = 0, + .rx_endian = 0, +}; + +static const struct of_device_id mtk_spi_of_match[] = { + { .compatible = "mediatek,mt6589-spi", .data = (void *)&mt6589_compat }, + { .compatible = "mediatek,mt8135-spi", .data = (void *)&mt8135_compat }, + { .compatible = "mediatek,mt8173-spi", .data = (void *)&mt8173_compat }, + {} +}; +MODULE_DEVICE_TABLE(of, mtk_spi_of_match); + +static void mtk_spi_reset(struct mtk_spi *mdata) +{ + u32 reg_val; + + /* set the software reset bit in SPI_CMD_REG. */ + reg_val = readl(mdata->base + SPI_CMD_REG); + reg_val |= SPI_CMD_RST; + writel(reg_val, mdata->base + SPI_CMD_REG); + + reg_val = readl(mdata->base + SPI_CMD_REG); + reg_val &= ~SPI_CMD_RST; + writel(reg_val, mdata->base + SPI_CMD_REG); +} + +static void mtk_spi_config(struct mtk_spi *mdata, + struct mtk_chip_config *chip_config) +{ + u32 reg_val; + + reg_val = readl(mdata->base + SPI_CMD_REG); + + /* set the mlsbx and mlsbtx */ + reg_val &= ~(SPI_CMD_TXMSBF | SPI_CMD_RXMSBF); + reg_val |= (chip_config->tx_mlsb << SPI_CMD_TXMSBF_OFFSET); + reg_val |= (chip_config->rx_mlsb << SPI_CMD_RXMSBF_OFFSET); + + /* set the tx/rx endian */ + reg_val &= ~(SPI_CMD_TX_ENDIAN | SPI_CMD_RX_ENDIAN); + reg_val |= (chip_config->tx_endian << SPI_CMD_TX_ENDIAN_OFFSET); + reg_val |= (chip_config->rx_endian << SPI_CMD_RX_ENDIAN_OFFSET); + + /* set finish and pause interrupt always enable */ + reg_val |= SPI_CMD_FINISH_IE | SPI_CMD_PAUSE_EN; + + /* disable dma mode */ + reg_val &= ~(SPI_CMD_TX_DMA | SPI_CMD_RX_DMA); + + /* disable deassert mode */ + reg_val &= ~SPI_CMD_DEASSERT; + + writel(reg_val, mdata->base + SPI_CMD_REG); + + /* pad select */ + if (mdata->dev_comp->need_pad_sel) + writel(mdata->pad_sel, mdata->base + SPI_PAD_SEL_REG); +} + +static int mtk_spi_prepare_hardware(struct spi_master *master) +{ + struct spi_transfer *trans; + struct mtk_spi *mdata = spi_master_get_devdata(master); + struct spi_message *msg = master->cur_msg; + int ret; + + ret = clk_prepare_enable(mdata->spi_clk); + if (ret < 0) { + dev_err(&master->dev, "failed to enable clock (%d)\n", ret); + return ret; + } + + trans = list_first_entry(&msg->transfers, struct spi_transfer, + transfer_list); + if (trans->cs_change == 0) { + mdata->state = MTK_SPI_IDLE; + mtk_spi_reset(mdata); + } + + return ret; +} + +static int mtk_spi_unprepare_hardware(struct spi_master *master) +{ + struct mtk_spi *mdata = spi_master_get_devdata(master); + + clk_disable_unprepare(mdata->spi_clk); + + return 0; +} + +static int mtk_spi_prepare_message(struct spi_master *master, + struct spi_message *msg) +{ + u32 reg_val; + u8 cpha, cpol; + struct mtk_chip_config *chip_config; + struct spi_device *spi = msg->spi; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + cpha = spi->mode & SPI_CPHA ? 1 : 0; + cpol = spi->mode & SPI_CPOL ? 1 : 0; + + reg_val = readl(mdata->base + SPI_CMD_REG); + reg_val &= ~(SPI_CMD_CPHA | SPI_CMD_CPOL); + reg_val |= (cpha << SPI_CMD_CPHA_OFFSET); + reg_val |= (cpol << SPI_CMD_CPOL_OFFSET); + writel(reg_val, mdata->base + SPI_CMD_REG); + + chip_config = spi->controller_data; + if (!chip_config) { + chip_config = (void *)&mtk_default_chip_info; + spi->controller_data = chip_config; + } + mtk_spi_config(mdata, chip_config); + + return 0; +} + +static void mtk_spi_set_cs(struct spi_device *spi, bool enable) +{ + u32 reg_val; + struct mtk_spi *mdata = spi_master_get_devdata(spi->master); + + reg_val = readl(mdata->base + SPI_CMD_REG); + if (!enable) + reg_val |= SPI_CMD_PAUSE_EN; + else + reg_val &= ~SPI_CMD_PAUSE_EN; + writel(reg_val, mdata->base + SPI_CMD_REG); +} + +static void mtk_spi_prepare_transfer(struct spi_master *master, + struct spi_transfer *xfer) +{ + u32 spi_clk_hz, div, high_time, low_time, holdtime, + setuptime, cs_idletime, reg_val = 0; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + spi_clk_hz = clk_get_rate(mdata->spi_clk); + if (xfer->speed_hz < spi_clk_hz / 2) + div = DIV_ROUND_UP(spi_clk_hz, xfer->speed_hz); + else + div = 1; + + high_time = (div + 1) / 2; + low_time = (div + 1) / 2; + holdtime = (div + 1) / 2 * 2; + setuptime = (div + 1) / 2 * 2; + cs_idletime = (div + 1) / 2 * 2; + + reg_val |= (((high_time - 1) & 0xff) << SPI_CFG0_SCK_HIGH_OFFSET); + reg_val |= (((low_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET); + reg_val |= (((holdtime - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET); + reg_val |= (((setuptime - 1) & 0xff) << SPI_CFG0_CS_SETUP_OFFSET); + writel(reg_val, mdata->base + SPI_CFG0_REG); + + reg_val = readl(mdata->base + SPI_CFG1_REG); + reg_val &= ~SPI_CFG1_CS_IDLE_MASK; + reg_val |= (((cs_idletime - 1) & 0xff) << SPI_CFG1_CS_IDLE_OFFSET); + writel(reg_val, mdata->base + SPI_CFG1_REG); +} + +static void mtk_spi_setup_packet(struct spi_master *master) +{ + u32 packet_size, packet_loop, reg_val; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + packet_size = min_t(unsigned, mdata->xfer_len, MTK_SPI_PACKET_SIZE); + packet_loop = mdata->xfer_len / packet_size; + + reg_val = readl(mdata->base + SPI_CFG1_REG); + reg_val &= ~(SPI_CFG1_PACKET_LENGTH_MASK + SPI_CFG1_PACKET_LOOP_MASK); + reg_val |= (packet_size - 1) << SPI_CFG1_PACKET_LENGTH_OFFSET; + reg_val |= (packet_loop - 1) << SPI_CFG1_PACKET_LOOP_OFFSET; + writel(reg_val, mdata->base + SPI_CFG1_REG); +} + +static void mtk_spi_enable_transfer(struct spi_master *master) +{ + int cmd; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + cmd = readl(mdata->base + SPI_CMD_REG); + if (mdata->state == MTK_SPI_IDLE) + cmd |= 1 << SPI_CMD_ACT_OFFSET; + else + cmd |= 1 << SPI_CMD_RESUME_OFFSET; + writel(cmd, mdata->base + SPI_CMD_REG); +} + +static int mtk_spi_get_mult_delta(int xfer_len) +{ + int mult_delta; + + if (xfer_len > MTK_SPI_PACKET_SIZE) + mult_delta = xfer_len % MTK_SPI_PACKET_SIZE; + else + mult_delta = 0; + + return mult_delta; +} + +static void mtk_spi_update_mdata_len(struct spi_master *master) +{ + int mult_delta; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + if (mdata->tx_sgl_len && mdata->rx_sgl_len) { + if (mdata->tx_sgl_len > mdata->rx_sgl_len) { + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; + mdata->rx_sgl_len = mult_delta; + mdata->tx_sgl_len -= mdata->xfer_len; + } else { + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; + mdata->tx_sgl_len = mult_delta; + mdata->rx_sgl_len -= mdata->xfer_len; + } + } else if (mdata->tx_sgl_len) { + mult_delta = mtk_spi_get_mult_delta(mdata->tx_sgl_len); + mdata->xfer_len = mdata->tx_sgl_len - mult_delta; + mdata->tx_sgl_len = mult_delta; + } else if (mdata->rx_sgl_len) { + mult_delta = mtk_spi_get_mult_delta(mdata->rx_sgl_len); + mdata->xfer_len = mdata->rx_sgl_len - mult_delta; + mdata->rx_sgl_len = mult_delta; + } +} + +static void mtk_spi_setup_dma_addr(struct spi_master *master, + struct spi_transfer *xfer) +{ + struct mtk_spi *mdata = spi_master_get_devdata(master); + + if (mdata->tx_sgl) + writel(cpu_to_le32(xfer->tx_dma), mdata->base + SPI_TX_SRC_REG); + if (mdata->rx_sgl) + writel(cpu_to_le32(xfer->rx_dma), mdata->base + SPI_RX_DST_REG); +} + +static int mtk_spi_fifo_transfer(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer) +{ + int cnt, i; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + mdata->cur_transfer = xfer; + mdata->xfer_len = xfer->len; + mtk_spi_prepare_transfer(master, xfer); + mtk_spi_setup_packet(master); + + if (xfer->len % 4) + cnt = xfer->len / 4 + 1; + else + cnt = xfer->len / 4; + + for (i = 0; i < cnt; i++) + writel(*((u32 *)xfer->tx_buf + i), + mdata->base + SPI_TX_DATA_REG); + + mtk_spi_enable_transfer(master); + + return 1; +} + +static int mtk_spi_dma_transfer(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer) +{ + int cmd; + struct mtk_spi *mdata = spi_master_get_devdata(master); + + mdata->tx_sgl = NULL; + mdata->rx_sgl = NULL; + mdata->tx_sgl_len = 0; + mdata->rx_sgl_len = 0; + mdata->cur_transfer = xfer; + + mtk_spi_prepare_transfer(master, xfer); + + cmd = readl(mdata->base + SPI_CMD_REG); + if (xfer->tx_buf) + cmd |= SPI_CMD_TX_DMA; + if (xfer->rx_buf) + cmd |= SPI_CMD_RX_DMA; + writel(cmd, mdata->base + SPI_CMD_REG); + + if (xfer->tx_buf) + mdata->tx_sgl = xfer->tx_sg.sgl; + if (xfer->rx_buf) + mdata->rx_sgl = xfer->rx_sg.sgl; + + if (mdata->tx_sgl) { + xfer->tx_dma = sg_dma_address(mdata->tx_sgl); + mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl); + } + if (mdata->rx_sgl) { + xfer->rx_dma = sg_dma_address(mdata->rx_sgl); + mdata->rx_sgl_len = sg_dma_len(mdata->rx_sgl); + } + + mtk_spi_update_mdata_len(master); + mtk_spi_setup_packet(master); + mtk_spi_setup_dma_addr(master, xfer); + mtk_spi_enable_transfer(master); + + return 1; +} + +static int mtk_spi_transfer_one(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer) +{ + if (master->can_dma(master, spi, xfer)) + return mtk_spi_dma_transfer(master, spi, xfer); + else + return mtk_spi_fifo_transfer(master, spi, xfer); +} + +static bool mtk_spi_can_dma(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer) +{ + return xfer->len > MTK_SPI_MAX_FIFO_SIZE; +} + +static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id) +{ + u32 cmd, reg_val, i; + struct spi_master *master = dev_id; + struct mtk_spi *mdata = spi_master_get_devdata(master); + struct spi_transfer *trans = mdata->cur_transfer; + + reg_val = readl(mdata->base + SPI_STATUS0_REG); + if (reg_val & 0x2) + mdata->state = MTK_SPI_PAUSED; + else + mdata->state = MTK_SPI_IDLE; + + if (!master->can_dma(master, master->cur_msg->spi, trans)) { + /* xfer len is not N*4 bytes every time in a transfer, + * but SPI_RX_DATA_REG must reads 4 bytes once, + * so rx buffer byte by byte. + */ + if (trans->rx_buf) { + for (i = 0; i < mdata->xfer_len; i++) { + if (i % 4 == 0) + reg_val = + readl(mdata->base + SPI_RX_DATA_REG); + *((u8 *)(trans->rx_buf + i)) = + (reg_val >> ((i % 4) * 8)) & 0xff; + } + } + spi_finalize_current_transfer(master); + return IRQ_HANDLED; + } + + if (mdata->tx_sgl) + trans->tx_dma += mdata->xfer_len; + if (mdata->rx_sgl) + trans->rx_dma += mdata->xfer_len; + + if (mdata->tx_sgl && (mdata->tx_sgl_len == 0)) { + mdata->tx_sgl = sg_next(mdata->tx_sgl); + if (mdata->tx_sgl) { + trans->tx_dma = sg_dma_address(mdata->tx_sgl); + mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl); + } + } + if (mdata->rx_sgl && (mdata->rx_sgl_len == 0)) { + mdata->rx_sgl = sg_next(mdata->rx_sgl); + if (mdata->rx_sgl) { + trans->rx_dma = sg_dma_address(mdata->rx_sgl); + mdata->rx_sgl_len = sg_dma_len(mdata->rx_sgl); + } + } + + if (!mdata->tx_sgl && !mdata->rx_sgl) { + /* spi disable dma */ + cmd = readl(mdata->base + SPI_CMD_REG); + cmd &= ~SPI_CMD_TX_DMA; + cmd &= ~SPI_CMD_RX_DMA; + writel(cmd, mdata->base + SPI_CMD_REG); + + spi_finalize_current_transfer(master); + return IRQ_HANDLED; + } + + mtk_spi_update_mdata_len(master); + mtk_spi_setup_packet(master); + mtk_spi_setup_dma_addr(master, trans); + mtk_spi_enable_transfer(master); + + return IRQ_HANDLED; +} + +static int mtk_spi_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct mtk_spi *mdata; + const struct of_device_id *of_id; + struct resource *res; + int irq, ret; + + master = spi_alloc_master(&pdev->dev, sizeof(*mdata)); + if (!master) { + dev_err(&pdev->dev, "failed to alloc spi master\n"); + return -ENOMEM; + } + + master->auto_runtime_pm = true; + master->dev.of_node = pdev->dev.of_node; + master->mode_bits = SPI_CPOL | SPI_CPHA; + + master->set_cs = mtk_spi_set_cs; + master->prepare_transfer_hardware = mtk_spi_prepare_hardware; + master->unprepare_transfer_hardware = mtk_spi_unprepare_hardware; + master->prepare_message = mtk_spi_prepare_message; + master->transfer_one = mtk_spi_transfer_one; + master->can_dma = mtk_spi_can_dma; + + of_id = of_match_node(mtk_spi_of_match, pdev->dev.of_node); + if (!of_id) { + dev_err(&pdev->dev, "failed to probe of_node\n"); + ret = -EINVAL; + goto err_put_master; + } + + mdata = spi_master_get_devdata(master); + mdata->dev_comp = of_id->data; + if (mdata->dev_comp->must_tx) + master->flags = SPI_MASTER_MUST_TX; + + if (mdata->dev_comp->need_pad_sel) { + ret = of_property_read_u32(pdev->dev.of_node, + "mediatek,pad-select", + &mdata->pad_sel); + if (ret) { + dev_err(&pdev->dev, "failed to read pad select: %d\n", + ret); + goto err_put_master; + } + + if (mdata->pad_sel > MT8173_SPI_MAX_PAD_SEL) { + dev_err(&pdev->dev, "wrong pad-select: %u\n", + mdata->pad_sel); + ret = -EINVAL; + goto err_put_master; + } + } + + platform_set_drvdata(pdev, master); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + ret = -ENODEV; + dev_err(&pdev->dev, "failed to determine base address\n"); + goto err_put_master; + } + + mdata->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(mdata->base)) { + ret = PTR_ERR(mdata->base); + goto err_put_master; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "failed to get irq (%d)\n", irq); + ret = irq; + goto err_put_master; + } + + if (!pdev->dev.dma_mask) + pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; + + ret = devm_request_irq(&pdev->dev, irq, mtk_spi_interrupt, + IRQF_TRIGGER_NONE, dev_name(&pdev->dev), master); + if (ret) { + dev_err(&pdev->dev, "failed to register irq (%d)\n", ret); + goto err_put_master; + } + + mdata->spi_clk = devm_clk_get(&pdev->dev, "spi-clk"); + if (IS_ERR(mdata->spi_clk)) { + ret = PTR_ERR(mdata->spi_clk); + dev_err(&pdev->dev, "failed to get spi-clk: %d\n", ret); + goto err_put_master; + } + + mdata->parent_clk = devm_clk_get(&pdev->dev, "parent-clk"); + if (IS_ERR(mdata->parent_clk)) { + ret = PTR_ERR(mdata->parent_clk); + dev_err(&pdev->dev, "failed to get parent-clk: %d\n", ret); + goto err_put_master; + } + + ret = clk_prepare_enable(mdata->spi_clk); + if (ret < 0) { + dev_err(&pdev->dev, "failed to enable spi_clk (%d)\n", ret); + goto err_put_master; + } + + ret = clk_set_parent(mdata->spi_clk, mdata->parent_clk); + if (ret < 0) { + dev_err(&pdev->dev, "failed to clk_set_parent (%d)\n", ret); + goto err_disable_clk; + } + + clk_disable_unprepare(mdata->spi_clk); + + pm_runtime_enable(&pdev->dev); + + ret = devm_spi_register_master(&pdev->dev, master); + if (ret) { + dev_err(&pdev->dev, "failed to register master (%d)\n", ret); + goto err_put_master; + } + + return 0; + +err_disable_clk: + clk_disable_unprepare(mdata->spi_clk); +err_put_master: + spi_master_put(master); + + return ret; +} + +static int mtk_spi_remove(struct platform_device *pdev) +{ + struct spi_master *master = platform_get_drvdata(pdev); + struct mtk_spi *mdata = spi_master_get_devdata(master); + + pm_runtime_disable(&pdev->dev); + + mtk_spi_reset(mdata); + clk_disable_unprepare(mdata->spi_clk); + spi_master_put(master); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int mtk_spi_suspend(struct device *dev) +{ + int ret; + struct spi_master *master = dev_get_drvdata(dev); + struct mtk_spi *mdata = spi_master_get_devdata(master); + + ret = spi_master_suspend(master); + if (ret) + return ret; + + if (!pm_runtime_suspended(dev)) + clk_disable_unprepare(mdata->spi_clk); + + return ret; +} + +static int mtk_spi_resume(struct device *dev) +{ + int ret; + struct spi_master *master = dev_get_drvdata(dev); + struct mtk_spi *mdata = spi_master_get_devdata(master); + + if (!pm_runtime_suspended(dev)) { + ret = clk_prepare_enable(mdata->spi_clk); + if (ret < 0) + return ret; + } + + ret = spi_master_resume(master); + if (ret < 0) + clk_disable_unprepare(mdata->spi_clk); + + return ret; +} +#endif /* CONFIG_PM_SLEEP */ + +#ifdef CONFIG_PM +static int mtk_spi_runtime_suspend(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct mtk_spi *mdata = spi_master_get_devdata(master); + + clk_disable_unprepare(mdata->spi_clk); + + return 0; +} + +static int mtk_spi_runtime_resume(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct mtk_spi *mdata = spi_master_get_devdata(master); + + return clk_prepare_enable(mdata->spi_clk); +} +#endif /* CONFIG_PM */ + +static const struct dev_pm_ops mtk_spi_pm = { + SET_SYSTEM_SLEEP_PM_OPS(mtk_spi_suspend, mtk_spi_resume) + SET_RUNTIME_PM_OPS(mtk_spi_runtime_suspend, + mtk_spi_runtime_resume, NULL) +}; + +struct platform_driver mtk_spi_driver = { + .driver = { + .name = "mtk-spi", + .pm = &mtk_spi_pm, + .of_match_table = mtk_spi_of_match, + }, + .probe = mtk_spi_probe, + .remove = mtk_spi_remove, +}; + +module_platform_driver(mtk_spi_driver); + +MODULE_DESCRIPTION("MTK SPI Controller driver"); +MODULE_AUTHOR("Leilk Liu <leilk.liu@mediatek.com>"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform: mtk_spi"); diff --git a/include/linux/platform_data/spi-mt65xx.h b/include/linux/platform_data/spi-mt65xx.h new file mode 100644 index 0000000..7512255 --- /dev/null +++ b/include/linux/platform_data/spi-mt65xx.h @@ -0,0 +1,22 @@ +/* + * MTK SPI bus driver definitions + * + * Copyright (c) 2015 MediaTek Inc. + * Author: Leilk Liu <leilk.liu@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef ____LINUX_PLATFORM_DATA_SPI_MTK_H +#define ____LINUX_PLATFORM_DATA_SPI_MTK_H + +/* Board specific platform_data */ +struct mtk_chip_config { + u32 tx_mlsb; + u32 rx_mlsb; + u32 tx_endian; + u32 rx_endian; +}; +#endif
This patch adds basic spi bus for MT8173. Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> --- Change in this patch: 1. change "pad-select" to "mediatek,pad-select". 2. modify clk relevant implement. --- drivers/spi/Kconfig | 9 + drivers/spi/Makefile | 1 + drivers/spi/spi-mt65xx.c | 749 +++++++++++++++++++++++++++++++ include/linux/platform_data/spi-mt65xx.h | 22 + 4 files changed, 781 insertions(+) create mode 100644 drivers/spi/spi-mt65xx.c create mode 100644 include/linux/platform_data/spi-mt65xx.h