| Message ID | 1439376845-17245-1-git-send-email-vthiagar@qti.qualcomm.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Kalle Valo |
| Headers | show |
Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> writes: > There are three WMI_CHAN_INFO events reported per channel > in QCA99X0 firmware. First one is a notification at the begining > of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0), > second one is a notification at the end of the dwell time with cmd_flag > CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication > with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for > the channel. Since there is a new state before the completion, the handler > is to fixed so that the counts are deducted from the ones reported with > CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE. > Without this fix there will be lots of 0 msecs reported as active > and busy time. > > Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Thanks, both applied.
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c index e6d6b42..38e22e0 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.c +++ b/drivers/net/wireless/ath/ath10k/wmi.c @@ -2412,8 +2412,10 @@ void ath10k_wmi_event_chan_info(struct ath10k *ar, struct sk_buff *skb) ar->ch_info_can_report_survey = true; } - ar->survey_last_rx_clear_count = rx_clear_count; - ar->survey_last_cycle_count = cycle_count; + if (!(cmd_flags & WMI_CHAN_INFO_FLAG_PRE_COMPLETE)) { + ar->survey_last_rx_clear_count = rx_clear_count; + ar->survey_last_cycle_count = cycle_count; + } exit: spin_unlock_bh(&ar->data_lock); diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h index 0d4efc9..5825c5c 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.h +++ b/drivers/net/wireless/ath/ath10k/wmi.h @@ -5585,6 +5585,7 @@ struct wmi_peer_sta_kickout_event { } __packed; #define WMI_CHAN_INFO_FLAG_COMPLETE BIT(0) +#define WMI_CHAN_INFO_FLAG_PRE_COMPLETE BIT(1) /* Beacon filter wmi command info */ #define BCN_FLT_MAX_SUPPORTED_IES 256
There are three WMI_CHAN_INFO events reported per channel in QCA99X0 firmware. First one is a notification at the begining of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0), second one is a notification at the end of the dwell time with cmd_flag CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for the channel. Since there is a new state before the completion, the handler is to fixed so that the counts are deducted from the ones reported with CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE. Without this fix there will be lots of 0 msecs reported as active and busy time. Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> --- drivers/net/wireless/ath/ath10k/wmi.c | 6 ++++-- drivers/net/wireless/ath/ath10k/wmi.h | 1 + 2 files changed, 5 insertions(+), 2 deletions(-)