| Message ID | 1441626325-20983-1-git-send-email-ivan.ivanov@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Delegated to: | Andy Gross |
| Headers | show |
On Mon, Sep 07, 2015 at 02:45:25PM +0300, Ivan T. Ivanov wrote: > On recent Qualcomm platforms VBUS and ID lines are not routed to > USB PHY LINK controller. Use extcon framework to receive connect > and disconnect ID and VBUS notification. > > Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> I will queue it for next rc1, thanks. Peter > --- > > Changes sice v3 [1]: > > * Migrate to new extcon framework API > * Address comments from Peter Chen. > > Tested DRD role with "qcom,ci-hdrc" and "qcom,usb-8x16-phy" on DB410c > > [1] https://lkml.org/lkml/2015/6/2/333 > > .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 6 + > drivers/usb/chipidea/Kconfig | 1 + > drivers/usb/chipidea/core.c | 125 +++++++++++++++++++++ > drivers/usb/chipidea/otg.c | 39 ++++++- > include/linux/usb/chipidea.h | 23 ++++ > 5 files changed, 193 insertions(+), 1 deletion(-) > > diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > index d71ef07bca5d..aea7d0af5fd6 100644 > --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > @@ -45,6 +45,11 @@ Optional properties: > (4 bytes), This register represents the maximum length of a the burst > in 32-bit words while moving data from the USB bus to system memory, > changing this value takes effect only the SBUSCFG.AHBBRST is 0. > +- extcon: phandles to external connector devices. First phandle should point to > + external connector, which provide "USB" cable events, the second should point > + to external connector device, which provide "USB-HOST" cable events. If one > + of the external connector devices is not required, empty <0> phandle should > + be specified. > > Example: > > @@ -61,4 +66,5 @@ Example: > ahb-burst-config = <0x0>; > tx-burst-size-dword = <0x10>; /* 64 bytes */ > rx-burst-size-dword = <0x10>; > + extcon = <0>, <&usb_id>; > }; > diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig > index 5ce3f1d6a6ed..5619b8ca3bf3 100644 > --- a/drivers/usb/chipidea/Kconfig > +++ b/drivers/usb/chipidea/Kconfig > @@ -1,6 +1,7 @@ > config USB_CHIPIDEA > tristate "ChipIdea Highspeed Dual Role Controller" > depends on ((USB_EHCI_HCD && USB_GADGET) || (USB_EHCI_HCD && !USB_GADGET) || (!USB_EHCI_HCD && USB_GADGET)) && HAS_DMA > + select EXTCON > help > Say Y here if your system has a dual role high speed USB > controller based on ChipIdea silicon IP. Currently, only the > diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c > index 3feebf7f31f0..573c2876b263 100644 > --- a/drivers/usb/chipidea/core.c > +++ b/drivers/usb/chipidea/core.c > @@ -47,6 +47,7 @@ > #include <linux/delay.h> > #include <linux/device.h> > #include <linux/dma-mapping.h> > +#include <linux/extcon.h> > #include <linux/phy/phy.h> > #include <linux/platform_device.h> > #include <linux/module.h> > @@ -602,9 +603,45 @@ static irqreturn_t ci_irq(int irq, void *data) > return ret; > } > > +static int ci_vbus_notifier(struct notifier_block *nb, unsigned long event, > + void *ptr) > +{ > + struct ci_hdrc_cable *vbus = container_of(nb, struct ci_hdrc_cable, nb); > + struct ci_hdrc *ci = vbus->ci; > + > + if (event) > + vbus->state = true; > + else > + vbus->state = false; > + > + vbus->changed = true; > + > + ci_irq(ci->irq, ci); > + return NOTIFY_DONE; > +} > + > +static int ci_id_notifier(struct notifier_block *nb, unsigned long event, > + void *ptr) > +{ > + struct ci_hdrc_cable *id = container_of(nb, struct ci_hdrc_cable, nb); > + struct ci_hdrc *ci = id->ci; > + > + if (event) > + id->state = false; > + else > + id->state = true; > + > + id->changed = true; > + > + ci_irq(ci->irq, ci); > + return NOTIFY_DONE; > +} > + > static int ci_get_platdata(struct device *dev, > struct ci_hdrc_platform_data *platdata) > { > + struct extcon_dev *ext_vbus, *ext_id; > + struct ci_hdrc_cable *cable; > int ret; > > if (!platdata->phy_mode) > @@ -695,9 +732,91 @@ static int ci_get_platdata(struct device *dev, > platdata->flags |= CI_HDRC_OVERRIDE_RX_BURST; > } > > + ext_id = ERR_PTR(-ENODEV); > + ext_vbus = ERR_PTR(-ENODEV); > + if (of_property_read_bool(dev->of_node, "extcon")) { > + /* Each one of them is not mandatory */ > + ext_vbus = extcon_get_edev_by_phandle(dev, 0); > + if (IS_ERR(ext_vbus) && PTR_ERR(ext_vbus) != -ENODEV) > + return PTR_ERR(ext_vbus); > + > + ext_id = extcon_get_edev_by_phandle(dev, 1); > + if (IS_ERR(ext_id) && PTR_ERR(ext_id) != -ENODEV) > + return PTR_ERR(ext_id); > + } > + > + cable = &platdata->vbus_extcon; > + cable->nb.notifier_call = ci_vbus_notifier; > + cable->edev = ext_vbus; > + > + if (!IS_ERR(ext_vbus)) { > + ret = extcon_get_cable_state_(cable->edev, EXTCON_USB); > + if (ret) > + cable->state = true; > + else > + cable->state = false; > + } > + > + cable = &platdata->id_extcon; > + cable->nb.notifier_call = ci_id_notifier; > + cable->edev = ext_id; > + > + if (!IS_ERR(ext_id)) { > + ret = extcon_get_cable_state_(cable->edev, EXTCON_USB_HOST); > + if (ret) > + cable->state = false; > + else > + cable->state = true; > + } > return 0; > } > > +static int ci_extcon_register(struct ci_hdrc *ci) > +{ > + struct ci_hdrc_cable *id, *vbus; > + int ret; > + > + id = &ci->platdata->id_extcon; > + id->ci = ci; > + if (!IS_ERR(id->edev)) { > + ret = extcon_register_notifier(id->edev, EXTCON_USB_HOST, > + &id->nb); > + if (ret < 0) { > + dev_err(ci->dev, "register ID failed\n"); > + return ret; > + } > + } > + > + vbus = &ci->platdata->vbus_extcon; > + vbus->ci = ci; > + if (!IS_ERR(vbus->edev)) { > + ret = extcon_register_notifier(vbus->edev, EXTCON_USB, > + &vbus->nb); > + if (ret < 0) { > + extcon_unregister_notifier(id->edev, EXTCON_USB_HOST, > + &id->nb); > + dev_err(ci->dev, "register VBUS failed\n"); > + return ret; > + } > + } > + > + return 0; > +} > + > +static void ci_extcon_unregister(struct ci_hdrc *ci) > +{ > + struct ci_hdrc_cable *cable; > + > + cable = &ci->platdata->id_extcon; > + if (!IS_ERR(cable->edev)) > + extcon_unregister_notifier(cable->edev, EXTCON_USB_HOST, > + &cable->nb); > + > + cable = &ci->platdata->vbus_extcon; > + if (!IS_ERR(cable->edev)) > + extcon_unregister_notifier(cable->edev, EXTCON_USB, &cable->nb); > +} > + > static DEFINE_IDA(ci_ida); > > struct platform_device *ci_hdrc_add_device(struct device *dev, > @@ -921,6 +1040,10 @@ static int ci_hdrc_probe(struct platform_device *pdev) > if (ret) > goto stop; > > + ret = ci_extcon_register(ci); > + if (ret) > + goto stop; > + > if (ci->supports_runtime_pm) { > pm_runtime_set_active(&pdev->dev); > pm_runtime_enable(&pdev->dev); > @@ -938,6 +1061,7 @@ static int ci_hdrc_probe(struct platform_device *pdev) > if (!ret) > return 0; > > + ci_extcon_unregister(ci); > stop: > ci_role_destroy(ci); > deinit_phy: > @@ -957,6 +1081,7 @@ static int ci_hdrc_remove(struct platform_device *pdev) > } > > dbg_remove_files(ci); > + ci_extcon_unregister(ci); > ci_role_destroy(ci); > ci_hdrc_enter_lpm(ci, true); > ci_usb_phy_exit(ci); > diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c > index ad6c87a4653c..ab4bd0c2d4ef 100644 > --- a/drivers/usb/chipidea/otg.c > +++ b/drivers/usb/chipidea/otg.c > @@ -30,7 +30,44 @@ > */ > u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask) > { > - return hw_read(ci, OP_OTGSC, mask); > + struct ci_hdrc_cable *cable; > + u32 val = hw_read(ci, OP_OTGSC, mask); > + > + /* > + * If using extcon framework for VBUS and/or ID signal > + * detection overwrite OTGSC register value > + */ > + cable = &ci->platdata->vbus_extcon; > + if (!IS_ERR(cable->edev)) { > + if (cable->changed) > + val |= OTGSC_BSVIS; > + else > + val &= ~OTGSC_BSVIS; > + > + cable->changed = false; > + > + if (cable->state) > + val |= OTGSC_BSV; > + else > + val &= ~OTGSC_BSV; > + } > + > + cable = &ci->platdata->id_extcon; > + if (!IS_ERR(cable->edev)) { > + if (cable->changed) > + val |= OTGSC_IDIS; > + else > + val &= ~OTGSC_IDIS; > + > + cable->changed = false; > + > + if (cable->state) > + val |= OTGSC_ID; > + else > + val &= ~OTGSC_ID; > + } > + > + return val; > } > > /** > diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h > index a41833cd184c..c5cddc6901d0 100644 > --- a/include/linux/usb/chipidea.h > +++ b/include/linux/usb/chipidea.h > @@ -5,9 +5,28 @@ > #ifndef __LINUX_USB_CHIPIDEA_H > #define __LINUX_USB_CHIPIDEA_H > > +#include <linux/extcon.h> > #include <linux/usb/otg.h> > > struct ci_hdrc; > + > +/** > + * struct ci_hdrc_cable - structure for external connector cable state tracking > + * @state: current state of the line > + * @changed: set to true when extcon event happen > + * @edev: device which generate events > + * @ci: driver state of the chipidea device > + * @nb: hold event notification callback > + * @conn: used for notification registration > + */ > +struct ci_hdrc_cable { > + bool state; > + bool changed; > + struct extcon_dev *edev; > + struct ci_hdrc *ci; > + struct notifier_block nb; > +}; > + > struct ci_hdrc_platform_data { > const char *name; > /* offset of the capability registers */ > @@ -48,6 +67,10 @@ struct ci_hdrc_platform_data { > u32 ahb_burst_config; > u32 tx_burst_size; > u32 rx_burst_size; > + > + /* VBUS and ID signal state tracking, using extcon framework */ > + struct ci_hdrc_cable vbus_extcon; > + struct ci_hdrc_cable id_extcon; > }; > > /* Default offset of capability registers */ > -- > 1.9.1 >
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index d71ef07bca5d..aea7d0af5fd6 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -45,6 +45,11 @@ Optional properties: (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from the USB bus to system memory, changing this value takes effect only the SBUSCFG.AHBBRST is 0. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. Example: @@ -61,4 +66,5 @@ Example: ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; }; diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig index 5ce3f1d6a6ed..5619b8ca3bf3 100644 --- a/drivers/usb/chipidea/Kconfig +++ b/drivers/usb/chipidea/Kconfig @@ -1,6 +1,7 @@ config USB_CHIPIDEA tristate "ChipIdea Highspeed Dual Role Controller" depends on ((USB_EHCI_HCD && USB_GADGET) || (USB_EHCI_HCD && !USB_GADGET) || (!USB_EHCI_HCD && USB_GADGET)) && HAS_DMA + select EXTCON help Say Y here if your system has a dual role high speed USB controller based on ChipIdea silicon IP. Currently, only the diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index 3feebf7f31f0..573c2876b263 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -47,6 +47,7 @@ #include <linux/delay.h> #include <linux/device.h> #include <linux/dma-mapping.h> +#include <linux/extcon.h> #include <linux/phy/phy.h> #include <linux/platform_device.h> #include <linux/module.h> @@ -602,9 +603,45 @@ static irqreturn_t ci_irq(int irq, void *data) return ret; } +static int ci_vbus_notifier(struct notifier_block *nb, unsigned long event, + void *ptr) +{ + struct ci_hdrc_cable *vbus = container_of(nb, struct ci_hdrc_cable, nb); + struct ci_hdrc *ci = vbus->ci; + + if (event) + vbus->state = true; + else + vbus->state = false; + + vbus->changed = true; + + ci_irq(ci->irq, ci); + return NOTIFY_DONE; +} + +static int ci_id_notifier(struct notifier_block *nb, unsigned long event, + void *ptr) +{ + struct ci_hdrc_cable *id = container_of(nb, struct ci_hdrc_cable, nb); + struct ci_hdrc *ci = id->ci; + + if (event) + id->state = false; + else + id->state = true; + + id->changed = true; + + ci_irq(ci->irq, ci); + return NOTIFY_DONE; +} + static int ci_get_platdata(struct device *dev, struct ci_hdrc_platform_data *platdata) { + struct extcon_dev *ext_vbus, *ext_id; + struct ci_hdrc_cable *cable; int ret; if (!platdata->phy_mode) @@ -695,9 +732,91 @@ static int ci_get_platdata(struct device *dev, platdata->flags |= CI_HDRC_OVERRIDE_RX_BURST; } + ext_id = ERR_PTR(-ENODEV); + ext_vbus = ERR_PTR(-ENODEV); + if (of_property_read_bool(dev->of_node, "extcon")) { + /* Each one of them is not mandatory */ + ext_vbus = extcon_get_edev_by_phandle(dev, 0); + if (IS_ERR(ext_vbus) && PTR_ERR(ext_vbus) != -ENODEV) + return PTR_ERR(ext_vbus); + + ext_id = extcon_get_edev_by_phandle(dev, 1); + if (IS_ERR(ext_id) && PTR_ERR(ext_id) != -ENODEV) + return PTR_ERR(ext_id); + } + + cable = &platdata->vbus_extcon; + cable->nb.notifier_call = ci_vbus_notifier; + cable->edev = ext_vbus; + + if (!IS_ERR(ext_vbus)) { + ret = extcon_get_cable_state_(cable->edev, EXTCON_USB); + if (ret) + cable->state = true; + else + cable->state = false; + } + + cable = &platdata->id_extcon; + cable->nb.notifier_call = ci_id_notifier; + cable->edev = ext_id; + + if (!IS_ERR(ext_id)) { + ret = extcon_get_cable_state_(cable->edev, EXTCON_USB_HOST); + if (ret) + cable->state = false; + else + cable->state = true; + } return 0; } +static int ci_extcon_register(struct ci_hdrc *ci) +{ + struct ci_hdrc_cable *id, *vbus; + int ret; + + id = &ci->platdata->id_extcon; + id->ci = ci; + if (!IS_ERR(id->edev)) { + ret = extcon_register_notifier(id->edev, EXTCON_USB_HOST, + &id->nb); + if (ret < 0) { + dev_err(ci->dev, "register ID failed\n"); + return ret; + } + } + + vbus = &ci->platdata->vbus_extcon; + vbus->ci = ci; + if (!IS_ERR(vbus->edev)) { + ret = extcon_register_notifier(vbus->edev, EXTCON_USB, + &vbus->nb); + if (ret < 0) { + extcon_unregister_notifier(id->edev, EXTCON_USB_HOST, + &id->nb); + dev_err(ci->dev, "register VBUS failed\n"); + return ret; + } + } + + return 0; +} + +static void ci_extcon_unregister(struct ci_hdrc *ci) +{ + struct ci_hdrc_cable *cable; + + cable = &ci->platdata->id_extcon; + if (!IS_ERR(cable->edev)) + extcon_unregister_notifier(cable->edev, EXTCON_USB_HOST, + &cable->nb); + + cable = &ci->platdata->vbus_extcon; + if (!IS_ERR(cable->edev)) + extcon_unregister_notifier(cable->edev, EXTCON_USB, &cable->nb); +} + static DEFINE_IDA(ci_ida); struct platform_device *ci_hdrc_add_device(struct device *dev, @@ -921,6 +1040,10 @@ static int ci_hdrc_probe(struct platform_device *pdev) if (ret) goto stop; + ret = ci_extcon_register(ci); + if (ret) + goto stop; + if (ci->supports_runtime_pm) { pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); @@ -938,6 +1061,7 @@ static int ci_hdrc_probe(struct platform_device *pdev) if (!ret) return 0; + ci_extcon_unregister(ci); stop: ci_role_destroy(ci); deinit_phy: @@ -957,6 +1081,7 @@ static int ci_hdrc_remove(struct platform_device *pdev) } dbg_remove_files(ci); + ci_extcon_unregister(ci); ci_role_destroy(ci); ci_hdrc_enter_lpm(ci, true); ci_usb_phy_exit(ci); diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c index ad6c87a4653c..ab4bd0c2d4ef 100644 --- a/drivers/usb/chipidea/otg.c +++ b/drivers/usb/chipidea/otg.c @@ -30,7 +30,44 @@ */ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask) { - return hw_read(ci, OP_OTGSC, mask); + struct ci_hdrc_cable *cable; + u32 val = hw_read(ci, OP_OTGSC, mask); + + /* + * If using extcon framework for VBUS and/or ID signal + * detection overwrite OTGSC register value + */ + cable = &ci->platdata->vbus_extcon; + if (!IS_ERR(cable->edev)) { + if (cable->changed) + val |= OTGSC_BSVIS; + else + val &= ~OTGSC_BSVIS; + + cable->changed = false; + + if (cable->state) + val |= OTGSC_BSV; + else + val &= ~OTGSC_BSV; + } + + cable = &ci->platdata->id_extcon; + if (!IS_ERR(cable->edev)) { + if (cable->changed) + val |= OTGSC_IDIS; + else + val &= ~OTGSC_IDIS; + + cable->changed = false; + + if (cable->state) + val |= OTGSC_ID; + else + val &= ~OTGSC_ID; + } + + return val; } /** diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h index a41833cd184c..c5cddc6901d0 100644 --- a/include/linux/usb/chipidea.h +++ b/include/linux/usb/chipidea.h @@ -5,9 +5,28 @@ #ifndef __LINUX_USB_CHIPIDEA_H #define __LINUX_USB_CHIPIDEA_H +#include <linux/extcon.h> #include <linux/usb/otg.h> struct ci_hdrc; + +/** + * struct ci_hdrc_cable - structure for external connector cable state tracking + * @state: current state of the line + * @changed: set to true when extcon event happen + * @edev: device which generate events + * @ci: driver state of the chipidea device + * @nb: hold event notification callback + * @conn: used for notification registration + */ +struct ci_hdrc_cable { + bool state; + bool changed; + struct extcon_dev *edev; + struct ci_hdrc *ci; + struct notifier_block nb; +}; + struct ci_hdrc_platform_data { const char *name; /* offset of the capability registers */ @@ -48,6 +67,10 @@ struct ci_hdrc_platform_data { u32 ahb_burst_config; u32 tx_burst_size; u32 rx_burst_size; + + /* VBUS and ID signal state tracking, using extcon framework */ + struct ci_hdrc_cable vbus_extcon; + struct ci_hdrc_cable id_extcon; }; /* Default offset of capability registers */
On recent Qualcomm platforms VBUS and ID lines are not routed to USB PHY LINK controller. Use extcon framework to receive connect and disconnect ID and VBUS notification. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> --- Changes sice v3 [1]: * Migrate to new extcon framework API * Address comments from Peter Chen. Tested DRD role with "qcom,ci-hdrc" and "qcom,usb-8x16-phy" on DB410c [1] https://lkml.org/lkml/2015/6/2/333 .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 6 + drivers/usb/chipidea/Kconfig | 1 + drivers/usb/chipidea/core.c | 125 +++++++++++++++++++++ drivers/usb/chipidea/otg.c | 39 ++++++- include/linux/usb/chipidea.h | 23 ++++ 5 files changed, 193 insertions(+), 1 deletion(-) -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html