| Message ID | 1441693083-8440-2-git-send-email-chunfeng.yun@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 09/08/2015 01:17 AM, Chunfeng Yun wrote: > add a DT binding documentation of usb3.0 phy for MT65xx > SoCs from Mediatek. > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> One comment, otherwise: Acked-by: Rob Herring <robh@kernel.org> > --- > .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 69 ++++++++++++++++++++++ > 1 file changed, 69 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > > diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > new file mode 100644 > index 0000000..5812d20 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > @@ -0,0 +1,69 @@ > +mt65xx USB3.0 PHY binding > +-------------------------- > + > +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. > + > +Required properties (controller (parent) node): > + - compatible : should be "mediatek,mt8173-u3phy" > + - reg : offset and length of register for phy, exclude port's > + register. > + - clocks : a list of phandle + clock-specifier pairs, one for each > + entry in clock-names > + - clock-names : must contain > + "u3phya_ref": for reference clock of usb3.0 analog phy. > + > +Required nodes : a sub-node is required for each port the controller > + provides. Address range information including the usual > + 'reg' property is used inside these nodes to describe > + the controller's topology. These nodes are translated > + by the driver's .xlate() function. The last sentence is Linux specific. Please remove. > + > +Required properties (port (child) node): > +- reg : address and length of the register set for the port. > +- #phy-cells : should be 1 (See second example) > + cell after port phandle is phy type from: > + - PHY_TYPE_USB2 > + - PHY_TYPE_USB3 > + > +Example: > + > +u3phy: usb-phy@11290000 { > + compatible = "mediatek,mt8173-u3phy"; > + reg = <0 0x11290000 0 0x800>; > + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; > + clock-names = "u3phya_ref"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + status = "okay"; > + > + phy_port0: port@11290800 { > + reg = <0 0x11290800 0 0x800>; > + #phy-cells = <1>; > + status = "okay"; > + }; > + > + phy_port1: port@11291000 { > + reg = <0 0x11291000 0 0x800>; > + #phy-cells = <1>; > + status = "okay"; > + }; > +}; > + > +Specifying phy control of devices > +--------------------------------- > + > +Device nodes should specify the configuration required in their "phys" > +property, containing a phandle to the phy port node and a device type; > +phy-names for each port are optional. > + > +Example: > + > +#include <dt-bindings/phy/phy.h> > + > +usb30: usb@11270000 { > + ... > + phys = <&phy_port0 PHY_TYPE_USB3>; > + phy-names = "usb3-0"; > + ... > +}; >
On 09/08/2015 01:17 AM, Chunfeng Yun wrote: > add a DT binding documentation of usb3.0 phy for MT65xx > SoCs from Mediatek. > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Rob Herring <robh@kernel.org> > --- > .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 69 ++++++++++++++++++++++ > 1 file changed, 69 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > > diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > new file mode 100644 > index 0000000..5812d20 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > @@ -0,0 +1,69 @@ > +mt65xx USB3.0 PHY binding > +-------------------------- > + > +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. > + > +Required properties (controller (parent) node): > + - compatible : should be "mediatek,mt8173-u3phy" > + - reg : offset and length of register for phy, exclude port's > + register. > + - clocks : a list of phandle + clock-specifier pairs, one for each > + entry in clock-names > + - clock-names : must contain > + "u3phya_ref": for reference clock of usb3.0 analog phy. > + > +Required nodes : a sub-node is required for each port the controller > + provides. Address range information including the usual > + 'reg' property is used inside these nodes to describe > + the controller's topology. These nodes are translated > + by the driver's .xlate() function. > + > +Required properties (port (child) node): > +- reg : address and length of the register set for the port. > +- #phy-cells : should be 1 (See second example) > + cell after port phandle is phy type from: > + - PHY_TYPE_USB2 > + - PHY_TYPE_USB3 > + > +Example: > + > +u3phy: usb-phy@11290000 { > + compatible = "mediatek,mt8173-u3phy"; > + reg = <0 0x11290000 0 0x800>; > + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; > + clock-names = "u3phya_ref"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + status = "okay"; > + > + phy_port0: port@11290800 { > + reg = <0 0x11290800 0 0x800>; > + #phy-cells = <1>; > + status = "okay"; > + }; > + > + phy_port1: port@11291000 { > + reg = <0 0x11291000 0 0x800>; > + #phy-cells = <1>; > + status = "okay"; > + }; > +}; > + > +Specifying phy control of devices > +--------------------------------- > + > +Device nodes should specify the configuration required in their "phys" > +property, containing a phandle to the phy port node and a device type; > +phy-names for each port are optional. > + > +Example: > + > +#include <dt-bindings/phy/phy.h> > + > +usb30: usb@11270000 { > + ... > + phys = <&phy_port0 PHY_TYPE_USB3>; > + phy-names = "usb3-0"; > + ... > +}; >
Hi, On Tue, 2015-09-08 at 19:16 -0500, Rob Herring wrote: > On 09/08/2015 01:17 AM, Chunfeng Yun wrote: > > add a DT binding documentation of usb3.0 phy for MT65xx > > SoCs from Mediatek. > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > One comment, otherwise: > > Acked-by: Rob Herring <robh@kernel.org> > > > --- > > .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 69 ++++++++++++++++++++++ > > 1 file changed, 69 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > > > > diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > > new file mode 100644 > > index 0000000..5812d20 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt > > @@ -0,0 +1,69 @@ > > +mt65xx USB3.0 PHY binding > > +-------------------------- > > + > > +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. > > + > > +Required properties (controller (parent) node): > > + - compatible : should be "mediatek,mt8173-u3phy" > > + - reg : offset and length of register for phy, exclude port's > > + register. > > + - clocks : a list of phandle + clock-specifier pairs, one for each > > + entry in clock-names > > + - clock-names : must contain > > + "u3phya_ref": for reference clock of usb3.0 analog phy. > > + > > +Required nodes : a sub-node is required for each port the controller > > + provides. Address range information including the usual > > + 'reg' property is used inside these nodes to describe > > + the controller's topology. These nodes are translated > > + by the driver's .xlate() function. > > The last sentence is Linux specific. Please remove. > Ok, I will remove it later. Thanks > > + > > +Required properties (port (child) node): > > +- reg : address and length of the register set for the port. > > +- #phy-cells : should be 1 (See second example) > > + cell after port phandle is phy type from: > > + - PHY_TYPE_USB2 > > + - PHY_TYPE_USB3 > > + > > +Example: > > + > > +u3phy: usb-phy@11290000 { > > + compatible = "mediatek,mt8173-u3phy"; > > + reg = <0 0x11290000 0 0x800>; > > + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; > > + clock-names = "u3phya_ref"; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + status = "okay"; > > + > > + phy_port0: port@11290800 { > > + reg = <0 0x11290800 0 0x800>; > > + #phy-cells = <1>; > > + status = "okay"; > > + }; > > + > > + phy_port1: port@11291000 { > > + reg = <0 0x11291000 0 0x800>; > > + #phy-cells = <1>; > > + status = "okay"; > > + }; > > +}; > > + > > +Specifying phy control of devices > > +--------------------------------- > > + > > +Device nodes should specify the configuration required in their "phys" > > +property, containing a phandle to the phy port node and a device type; > > +phy-names for each port are optional. > > + > > +Example: > > + > > +#include <dt-bindings/phy/phy.h> > > + > > +usb30: usb@11270000 { > > + ... > > + phys = <&phy_port0 PHY_TYPE_USB3>; > > + phy-names = "usb3-0"; > > + ... > > +}; > > >
diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file mode 100644 index 0000000..5812d20 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -0,0 +1,69 @@ +mt65xx USB3.0 PHY binding +-------------------------- + +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,mt8173-u3phy" + - reg : offset and length of register for phy, exclude port's + register. + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "u3phya_ref": for reference clock of usb3.0 analog phy. + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. These nodes are translated + by the driver's .xlate() function. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- #phy-cells : should be 1 (See second example) + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +Example: + +u3phy: usb-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0 0x11290000 0 0x800>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "u3phya_ref"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "okay"; + + phy_port0: port@11290800 { + reg = <0 0x11290800 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; + + phy_port1: port@11291000 { + reg = <0 0x11291000 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; +}; + +Specifying phy control of devices +--------------------------------- + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type; +phy-names for each port are optional. + +Example: + +#include <dt-bindings/phy/phy.h> + +usb30: usb@11270000 { + ... + phys = <&phy_port0 PHY_TYPE_USB3>; + phy-names = "usb3-0"; + ... +};
add a DT binding documentation of usb3.0 phy for MT65xx SoCs from Mediatek. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 69 ++++++++++++++++++++++ 1 file changed, 69 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt