diff mbox

[v8,3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

Message ID 1442385864-4368-4-git-send-email-chunfeng.yun@mediatek.com (mailing list archive)
State New, archived
Headers show

Commit Message

Chunfeng Yun Sept. 16, 2015, 6:44 a.m. UTC 
support usb3.0 phy of mt65xx SoCs

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/phy/Kconfig           |   9 +
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 466 insertions(+)
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c

Comments

Kishon Vijay Abraham I Sept. 18, 2015, 6:42 a.m. UTC | #1 
Hi,

On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> support usb3.0 phy of mt65xx SoCs
few nitpicks:

change $subject. This driver is no longer in usb directory.

It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
>  drivers/phy/Kconfig           |   9 +
>  drivers/phy/Makefile          |   1 +
>  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 466 insertions(+)
>  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..ec436c1 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
>  	help
>  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
>  
> +config PHY_MT65XX_USB3
> +	tristate "Mediatek USB3.0 PHY Driver"
> +	depends on ARCH_MEDIATEK && OF
> +	select GENERIC_PHY
> +	help
> +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> +	  for mt65xx SoCs. it supports two usb2.0 ports and
> +	  one usb3.0 port.
> +
>  config PHY_SUN4I_USB
>  	tristate "Allwinner sunxi SoC USB PHY driver"
>  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..a7cc629 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
>  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
>  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
>  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
>  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
>  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> new file mode 100644
> index 0000000..1f00b05
> --- /dev/null
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -0,0 +1,456 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +/*
> + * for sifslv2 register, but exclude port's;
> + * relative to USB3_SIF2_BASE base address
> + */
> +#define SSUSB_SIFSLV_SPLLC		0x0000
> +
> +/* offsets of sub-segment in each port registers */
> +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> +
> +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> +
> +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> +
> +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> +
> +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> +#define PA6_RG_U2_ISO_EN		BIT(31)
> +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> +
> +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> +#define P2C_USB20_GPIO_MODE		BIT(8)
> +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> +
> +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> +
> +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> +#define P2C_FORCE_UART_EN		BIT(26)
> +#define P2C_FORCE_DATAIN		BIT(23)
> +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> +#define P2C_FORCE_XCVRSEL		BIT(19)
> +#define P2C_FORCE_SUSPENDM		BIT(18)
> +#define P2C_FORCE_TERMSEL		BIT(17)
> +#define P2C_RG_DATAIN			GENMASK(13, 10)
> +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> +#define P2C_RG_DMPULLDOWN		BIT(7)
> +#define P2C_RG_DPPULLDOWN		BIT(6)
> +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> +#define P2C_RG_SUSPENDM			BIT(3)
> +#define P2C_RG_TERMSEL			BIT(2)
> +#define P2C_DTM0_PART_MASK \
> +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> +
> +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> +#define P2C_RG_UART_EN			BIT(16)
> +#define P2C_RG_VBUSVALID		BIT(5)
> +#define P2C_RG_SESSEND			BIT(4)
> +#define P2C_RG_AVALID			BIT(2)
> +
> +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> +
> +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> +
> +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> +
> +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> +
> +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> +
> +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> +
> +struct mt65xx_phy_instance {
> +	struct phy *phy;
> +	void __iomem *port_base;
> +	u32 index;
> +	u8 type;
> +};
> +
> +struct mt65xx_u3phy {
> +	struct device *dev;
> +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> +	struct mt65xx_phy_instance **phys;
> +	int nphys;
> +};
> +
> +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	/* switch to USB function. (system register, force ip into usb mode) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~P2C_FORCE_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	tmp = readl(port_base + U3P_U2PHYDTM1);
> +	tmp &= ~P2C_RG_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM1);
> +
> +	if (!index) {
> +		tmp = readl(port_base + U3P_U2PHYACR4);
> +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> +		writel(tmp, port_base + U3P_U2PHYACR4);
> +	}
> +
> +	/* DP/DM BC1.1 path Disable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> +	tmp &= ~P3A_RG_RX_DAC_MUX;
> +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> +
> +	tmp = readl(port_base + U3P_PHYD_CDR1);
> +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> +	writel(tmp, port_base + U3P_PHYD_CDR1);
> +
> +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> +}
> +
> +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	if (!index) {
> +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> +		tmp |= P3A_RG_U3_VUSB10_ON;
> +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> +	}
> +
> +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	/* OTG Enable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	if (!index) {
> +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> +		/* [mt8173]disable Change 100uA current from SSUSB */
> +		tmp = readl(port_base + U3P_USBPHYACR5);
> +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> +		writel(tmp, port_base + U3P_USBPHYACR5);
> +	}
> +	udelay(800);

It's good to document delay values. Is it a recommended value from the
data manual?

Also now the registers doesn't seem to be shared between the PHYs. But
if it is then all these functions have to be protected with spinlock.

Thanks
Kishon
Chunfeng Yun Sept. 28, 2015, 3:35 a.m. UTC | #2 
hi,
On Fri, 2015-09-18 at 12:12 +0530, Kishon Vijay Abraham I wrote:
> Hi,
> 
> On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> > support usb3.0 phy of mt65xx SoCs
> few nitpicks:
> 
> change $subject. This driver is no longer in usb directory.
> 
> It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
Ok

> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> >  drivers/phy/Kconfig           |   9 +
> >  drivers/phy/Makefile          |   1 +
> >  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 466 insertions(+)
> >  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> > 
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 47da573..ec436c1 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
> >  	help
> >  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
> >  
> > +config PHY_MT65XX_USB3
> > +	tristate "Mediatek USB3.0 PHY Driver"
> > +	depends on ARCH_MEDIATEK && OF
> > +	select GENERIC_PHY
> > +	help
> > +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> > +	  for mt65xx SoCs. it supports two usb2.0 ports and
> > +	  one usb3.0 port.
> > +
> >  config PHY_SUN4I_USB
> >  	tristate "Allwinner sunxi SoC USB PHY driver"
> >  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index a5b18c1..a7cc629 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
> >  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
> >  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> > +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
> >  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
> >  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> > diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> > new file mode 100644
> > index 0000000..1f00b05
> > --- /dev/null
> > +++ b/drivers/phy/phy-mt65xx-usb3.c
> > @@ -0,0 +1,456 @@
> > +/*
> > + * Copyright (c) 2015 MediaTek Inc.
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +
> > +/*
> > + * for sifslv2 register, but exclude port's;
> > + * relative to USB3_SIF2_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_SPLLC		0x0000
> > +
> > +/* offsets of sub-segment in each port registers */
> > +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> > +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> > +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> > +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> > +
> > +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> > +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > +
> > +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> > +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > +
> > +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> > +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> > +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> > +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> > +
> > +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> > +#define PA6_RG_U2_ISO_EN		BIT(31)
> > +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> > +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> > +
> > +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> > +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> > +#define P2C_USB20_GPIO_MODE		BIT(8)
> > +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > +
> > +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> > +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > +
> > +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> > +#define P2C_FORCE_UART_EN		BIT(26)
> > +#define P2C_FORCE_DATAIN		BIT(23)
> > +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> > +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> > +#define P2C_FORCE_XCVRSEL		BIT(19)
> > +#define P2C_FORCE_SUSPENDM		BIT(18)
> > +#define P2C_FORCE_TERMSEL		BIT(17)
> > +#define P2C_RG_DATAIN			GENMASK(13, 10)
> > +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> > +#define P2C_RG_DMPULLDOWN		BIT(7)
> > +#define P2C_RG_DPPULLDOWN		BIT(6)
> > +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> > +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> > +#define P2C_RG_SUSPENDM			BIT(3)
> > +#define P2C_RG_TERMSEL			BIT(2)
> > +#define P2C_DTM0_PART_MASK \
> > +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> > +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> > +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> > +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> > +
> > +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> > +#define P2C_RG_UART_EN			BIT(16)
> > +#define P2C_RG_VBUSVALID		BIT(5)
> > +#define P2C_RG_SESSEND			BIT(4)
> > +#define P2C_RG_AVALID			BIT(2)
> > +
> > +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> > +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> > +
> > +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> > +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> > +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> > +
> > +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> > +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> > +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> > +
> > +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> > +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> > +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> > +
> > +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> > +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> > +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> > +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> > +
> > +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> > +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> > +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> > +
> > +struct mt65xx_phy_instance {
> > +	struct phy *phy;
> > +	void __iomem *port_base;
> > +	u32 index;
> > +	u8 type;
> > +};
> > +
> > +struct mt65xx_u3phy {
> > +	struct device *dev;
> > +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> > +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> > +	struct mt65xx_phy_instance **phys;
> > +	int nphys;
> > +};
> > +
> > +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~P2C_FORCE_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	tmp = readl(port_base + U3P_U2PHYDTM1);
> > +	tmp &= ~P2C_RG_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM1);
> > +
> > +	if (!index) {
> > +		tmp = readl(port_base + U3P_U2PHYACR4);
> > +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> > +		writel(tmp, port_base + U3P_U2PHYACR4);
> > +	}
> > +
> > +	/* DP/DM BC1.1 path Disable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> > +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> > +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> > +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> > +	tmp &= ~P3A_RG_RX_DAC_MUX;
> > +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> > +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> > +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> > +
> > +	tmp = readl(port_base + U3P_PHYD_CDR1);
> > +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> > +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> > +	writel(tmp, port_base + U3P_PHYD_CDR1);
> > +
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> > +		tmp |= P3A_RG_U3_VUSB10_ON;
> > +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> > +	}
> > +
> > +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> > +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	/* OTG Enable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	if (!index) {
> > +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> > +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> > +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> > +		/* [mt8173]disable Change 100uA current from SSUSB */
> > +		tmp = readl(port_base + U3P_USBPHYACR5);
> > +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> > +		writel(tmp, port_base + U3P_USBPHYACR5);
> > +	}
> > +	udelay(800);
> 
> It's good to document delay values. Is it a recommended value from the
> data manual?
> 
I check it with DE, and revise it after many tests.

> Also now the registers doesn't seem to be shared between the PHYs. But
> if it is then all these functions have to be protected with spinlock.
> 
I will pay attention to it.

Thanks a lot

> Thanks
> Kishon
diff mbox

Patch

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 47da573..ec436c1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -206,6 +206,15 @@  config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a5b18c1..a7cc629 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -23,6 +23,7 @@  obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
new file mode 100644
index 0000000..1f00b05
--- /dev/null
+++ b/drivers/phy/phy-mt65xx-usb3.c
@@ -0,0 +1,456 @@ 
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+/*
+ * for sifslv2 register, but exclude port's;
+ * relative to USB3_SIF2_BASE base address
+ */
+#define SSUSB_SIFSLV_SPLLC		0x0000
+
+/* offsets of sub-segment in each port registers */
+#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
+#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
+#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
+#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
+
+#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+
+#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
+
+#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
+#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
+#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
+
+#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define PA6_RG_U2_ISO_EN		BIT(31)
+#define PA6_RG_U2_BC11_SW_EN		BIT(23)
+#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+
+#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define P2C_RG_USB20_GPIO_CTL		BIT(9)
+#define P2C_USB20_GPIO_MODE		BIT(8)
+#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+
+#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
+
+#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define P2C_FORCE_UART_EN		BIT(26)
+#define P2C_FORCE_DATAIN		BIT(23)
+#define P2C_FORCE_DM_PULLDOWN		BIT(21)
+#define P2C_FORCE_DP_PULLDOWN		BIT(20)
+#define P2C_FORCE_XCVRSEL		BIT(19)
+#define P2C_FORCE_SUSPENDM		BIT(18)
+#define P2C_FORCE_TERMSEL		BIT(17)
+#define P2C_RG_DATAIN			GENMASK(13, 10)
+#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
+#define P2C_RG_DMPULLDOWN		BIT(7)
+#define P2C_RG_DPPULLDOWN		BIT(6)
+#define P2C_RG_XCVRSEL			GENMASK(5, 4)
+#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
+#define P2C_RG_SUSPENDM			BIT(3)
+#define P2C_RG_TERMSEL			BIT(2)
+#define P2C_DTM0_PART_MASK \
+		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
+		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
+		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
+		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
+
+#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define P2C_RG_UART_EN			BIT(16)
+#define P2C_RG_VBUSVALID		BIT(5)
+#define P2C_RG_SESSEND			BIT(4)
+#define P2C_RG_AVALID			BIT(2)
+
+#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
+#define P3A_RG_U3_VUSB10_ON		BIT(5)
+
+#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
+#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
+#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
+
+#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
+#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
+#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
+
+#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
+#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
+#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
+
+#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
+#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
+#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
+#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
+
+#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
+#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
+#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
+
+struct mt65xx_phy_instance {
+	struct phy *phy;
+	void __iomem *port_base;
+	u32 index;
+	u8 type;
+};
+
+struct mt65xx_u3phy {
+	struct device *dev;
+	void __iomem *sif_base;	/* include sif2, but exclude port's */
+	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	struct mt65xx_phy_instance **phys;
+	int nphys;
+};
+
+static void phy_instance_init(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	/* switch to USB function. (system register, force ip into usb mode) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_FORCE_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~P2C_RG_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U2PHYACR4);
+		tmp &= ~P2C_U2_GPIO_CTR_MSK;
+		writel(tmp, port_base + U3P_U2PHYACR4);
+	}
+
+	/* DP/DM BC1.1 path Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_BC11_SW_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
+	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
+	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG9);
+	tmp &= ~P3A_RG_RX_DAC_MUX;
+	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
+	writel(tmp, port_base + U3P_U3_PHYA_REG9);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG6);
+	tmp &= ~P3A_RG_TX_EIDLE_CM;
+	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
+	writel(tmp, port_base + U3P_U3_PHYA_REG6);
+
+	tmp = readl(port_base + U3P_PHYD_CDR1);
+	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
+	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
+	writel(tmp, port_base + U3P_PHYD_CDR1);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (!index) {
+		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp |= P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
+	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Enable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
+		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+		/* [mt8173]disable Change 100uA current from SSUSB */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
+	tmp &= ~P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+	/* USB 2.0 slew rate calibration */
+	tmp = readl(port_base + U3P_USBPHYACR5);
+	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
+	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
+	writel(tmp, port_base + U3P_USBPHYACR5);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
+	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
+	tmp |= P2C_FORCE_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+	if (!index) {
+		/* (also disable)Change 100uA current switch to USB2.0 */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	/* let suspendm=0, set utmi into analog power down */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_RG_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+	udelay(1);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
+	tmp |= P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static int mt65xx_phy_init(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	ret = clk_prepare_enable(u3phy->u3phya_ref);
+	if (ret) {
+		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
+		return ret;
+	}
+
+	phy_instance_init(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_on(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_on(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_off(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_off(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_exit(struct phy *phy)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	clk_disable_unprepare(u3phy->u3phya_ref);
+	return 0;
+}
+
+static struct phy *mt65xx_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
+	struct mt65xx_phy_instance *instance = NULL;
+	struct device_node *phy_np = args->np;
+	int index;
+
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < u3phy->nphys; index++)
+		if (phy_np == u3phy->phys[index]->phy->dev.of_node) {
+			instance = u3phy->phys[index];
+			break;
+		}
+
+	if (!instance) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	instance->type = args->args[0];
+
+	if (!(instance->type == PHY_TYPE_USB2 ||
+	      instance->type == PHY_TYPE_USB3)) {
+		dev_err(dev, "unsupported device type: %d\n", instance->type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return instance->phy;
+}
+
+static struct phy_ops mt65xx_u3phy_ops = {
+	.init		= mt65xx_phy_init,
+	.exit		= mt65xx_phy_exit,
+	.power_on	= mt65xx_phy_power_on,
+	.power_off	= mt65xx_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mt65xx_u3phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct resource *sif_res;
+	struct mt65xx_u3phy *u3phy;
+	struct resource res;
+	int port;
+
+	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+	if (!u3phy)
+		return -ENOMEM;
+
+	u3phy->nphys = of_get_child_count(np);
+	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
+				       sizeof(*u3phy->phys), GFP_KERNEL);
+	if (!u3phy->phys)
+		return -ENOMEM;
+
+	u3phy->dev = dev;
+	platform_set_drvdata(pdev, u3phy);
+
+	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+	if (IS_ERR(u3phy->sif_base)) {
+		dev_err(dev, "failed to remap sif regs\n");
+		return PTR_ERR(u3phy->sif_base);
+	}
+
+	u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref");
+	if (IS_ERR(u3phy->u3phya_ref)) {
+		dev_err(dev, "error to get u3phya_ref\n");
+		return PTR_ERR(u3phy->u3phya_ref);
+	}
+
+	port = 0;
+	for_each_child_of_node(np, child_np) {
+		struct mt65xx_phy_instance *instance;
+		struct phy *phy;
+		int retval;
+
+		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
+		if (!instance)
+			return -ENOMEM;
+
+		u3phy->phys[port] = instance;
+
+		phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			return PTR_ERR(phy);
+		}
+
+		retval = of_address_to_resource(child_np, 0, &res);
+		if (retval) {
+			dev_err(dev, "failed to get address resource(id-%d)\n",
+				port);
+			return retval;
+		}
+
+		instance->port_base = devm_ioremap_resource(&phy->dev, &res);
+		if (IS_ERR(instance->port_base)) {
+			dev_err(dev, "failed to remap phy regs\n");
+			return PTR_ERR(instance->port_base);
+		}
+
+		instance->phy = phy;
+		instance->index = port;
+		phy_set_drvdata(phy, instance);
+		port++;
+	}
+
+	provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt8173-u3phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
+static struct platform_driver mt65xx_u3phy_driver = {
+	.probe		= mt65xx_u3phy_probe,
+	.driver		= {
+		.name	= "mt65xx-u3phy",
+		.of_match_table = mt65xx_u3phy_id_table,
+	},
+};
+
+module_platform_driver(mt65xx_u3phy_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("mt65xx USB PHY driver");
+MODULE_LICENSE("GPL v2");