| Message ID | 1445530847-25217-1-git-send-email-afd@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Andrew F. Davis <afd@ti.com> [151022 09:21]: > Using constants for pinctrl allows better readability and removes > redundancy with comments. You should use the include/dt-bindings/pinctrl/omap.h macro AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching the same things again later on. Regards, Tony > Signed-off-by: Andrew F. Davis <afd@ti.com> > --- > arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++----------------- > 1 file changed, 22 insertions(+), 22 deletions(-) > > diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts > index eadbba3..a540a10 100644 > --- a/arch/arm/boot/dts/am335x-boneblack.dts > +++ b/arch/arm/boot/dts/am335x-boneblack.dts > @@ -36,32 +36,32 @@ > &am33xx_pinmux { > nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { > pinctrl-single,pins = < > - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ > - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ > - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ > - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ > - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ > - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ > + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ > + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ > + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ > + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ > + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ > + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ > + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ > + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ > + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ > + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ > + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ > + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ > + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ > + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ > + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ > + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ > + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ > + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ > + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ > + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ > + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ > >; > }; > nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { > pinctrl-single,pins = < > - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ > + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ > >; > }; > }; > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 10/22/2015 04:23 PM, Tony Lindgren wrote: > * Andrew F. Davis <afd@ti.com> [151022 09:21]: >> Using constants for pinctrl allows better readability and removes >> redundancy with comments. > > You should use the include/dt-bindings/pinctrl/omap.h macro > AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching > the same things again later on. > Hmm, I haven't really been following this change, it kind of seems to add some unnecessary abstraction by using physical hardware addresses instead of offsets, then just converting them back to offsets. The offset style DT nodes are already auto-generated with existing tools anyway: https://dev.ti.com/pinmux I'm sure this has been discussed already so if this is a blocker I'll re-spin this. Andrew > Regards, > > Tony > >> Signed-off-by: Andrew F. Davis <afd@ti.com> >> --- >> arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++----------------- >> 1 file changed, 22 insertions(+), 22 deletions(-) >> >> diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts >> index eadbba3..a540a10 100644 >> --- a/arch/arm/boot/dts/am335x-boneblack.dts >> +++ b/arch/arm/boot/dts/am335x-boneblack.dts >> @@ -36,32 +36,32 @@ >> &am33xx_pinmux { >> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { >> pinctrl-single,pins = < >> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ >> - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ >> - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ >> - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ >> - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ >> - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ >> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ >> + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ >> + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ >> + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ >> + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ >> + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ >> + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ >> + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ >> + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ >> + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ >> + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ >> + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ >> + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ >> + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ >> + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ >> + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ >> + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ >> + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ >> + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ >> + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ >> + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ >> >; >> }; >> nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { >> pinctrl-single,pins = < >> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ >> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ >> >; >> }; >> }; >> -- >> 1.9.1 >> -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello Andrew, On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote: > On 10/22/2015 04:23 PM, Tony Lindgren wrote: >> >> * Andrew F. Davis <afd@ti.com> [151022 09:21]: >>> >>> Using constants for pinctrl allows better readability and removes >>> redundancy with comments. >> >> >> You should use the include/dt-bindings/pinctrl/omap.h macro >> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching >> the same things again later on. >> > > Hmm, I haven't really been following this change, it kind of seems to add > some unnecessary abstraction by using physical hardware addresses instead > of offsets, then just converting them back to offsets. The offset style DT > nodes are already auto-generated with existing tools anyway: > https://dev.ti.com/pinmux > > I'm sure this has been discussed already so if this is a blocker I'll > re-spin this. > The good thing about the IOPAD pinmux macros is that matches what is in the TRM so it is easier to read the DTS and verify that is correct. I've on my queue to migrate all the remaining DTS for TI SoCs to use the IOPAD macros but is just that I didn't have time to do it this week. Probably I'll do it at the end of the next week. > Andrew > > >> Regards, >> Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 10/23/2015 09:29 AM, Javier Martinez Canillas wrote: > Hello Andrew, > > On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote: >> On 10/22/2015 04:23 PM, Tony Lindgren wrote: >>> >>> * Andrew F. Davis <afd@ti.com> [151022 09:21]: >>>> >>>> Using constants for pinctrl allows better readability and removes >>>> redundancy with comments. >>> >>> >>> You should use the include/dt-bindings/pinctrl/omap.h macro >>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching >>> the same things again later on. >>> >> >> Hmm, I haven't really been following this change, it kind of seems to add >> some unnecessary abstraction by using physical hardware addresses instead >> of offsets, then just converting them back to offsets. The offset style DT >> nodes are already auto-generated with existing tools anyway: >> https://dev.ti.com/pinmux >> >> I'm sure this has been discussed already so if this is a blocker I'll >> re-spin this. >> > > The good thing about the IOPAD pinmux macros is that matches what is > in the TRM so it is easier to read the DTS and verify that is correct. > > I've on my queue to migrate all the remaining DTS for TI SoCs to use > the IOPAD macros but is just that I didn't have time to do it this > week. Probably I'll do it at the end of the next week. > Then this patch can probably be dropped, hopefully the converted constants in this patch can be of some help for you though. Andrew >> Andrew >> >> >>> Regards, >>> > > Best regards, > Javier > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello Andrew, On Fri, Oct 23, 2015 at 4:36 PM, Andrew F. Davis <afd@ti.com> wrote: > On 10/23/2015 09:29 AM, Javier Martinez Canillas wrote: >> >> Hello Andrew, >> >> On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote: >>> >>> On 10/22/2015 04:23 PM, Tony Lindgren wrote: >>>> >>>> >>>> * Andrew F. Davis <afd@ti.com> [151022 09:21]: >>>>> >>>>> >>>>> Using constants for pinctrl allows better readability and removes >>>>> redundancy with comments. >>>> >>>> >>>> >>>> You should use the include/dt-bindings/pinctrl/omap.h macro >>>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching >>>> the same things again later on. >>>> >>> >>> Hmm, I haven't really been following this change, it kind of seems to add >>> some unnecessary abstraction by using physical hardware addresses instead >>> of offsets, then just converting them back to offsets. The offset style >>> DT >>> nodes are already auto-generated with existing tools anyway: >>> https://dev.ti.com/pinmux >>> >>> I'm sure this has been discussed already so if this is a blocker I'll >>> re-spin this. >>> >> >> The good thing about the IOPAD pinmux macros is that matches what is >> in the TRM so it is easier to read the DTS and verify that is correct. >> >> I've on my queue to migrate all the remaining DTS for TI SoCs to use >> the IOPAD macros but is just that I didn't have time to do it this >> week. Probably I'll do it at the end of the next week. >> > > Then this patch can probably be dropped, hopefully the converted constants > in this patch can be of some help for you though. > Yes they are but feel free to re-spin your patch if you wish, it will be one less DTS to convert :-) But yes, if you don't then I'll do it when changing all DTS. > Andrew > > Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index eadbba3..a540a10 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -36,32 +36,32 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { pinctrl-single,pins = < - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ >; }; nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { pinctrl-single,pins = < - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ >; }; };
Using constants for pinctrl allows better readability and removes redundancy with comments. Signed-off-by: Andrew F. Davis <afd@ti.com> --- arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++----------------- 1 file changed, 22 insertions(+), 22 deletions(-)