| Message ID | 1449249057-12975-1-git-send-email-yrdreddy@broadcom.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, Dec 04, 2015 at 12:10:57PM -0500, Yendapally Reddy Dhananjaya Reddy wrote: > Device tree binding documentation for Broadcom NSP GPIO-a > > Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com> Acked-by: Rob Herring <robh@kernel.org> > --- > .../devicetree/bindings/pinctrl/brcm,nsp-gpio.txt | 80 ++++++++++++++++++++++ > 1 file changed, 80 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt > > diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt > new file mode 100644 > index 0000000..0844168 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt > @@ -0,0 +1,80 @@ > +Broadcom Northstar plus (NSP) GPIO/PINCONF Controller > + > +Required properties: > +- compatible: > + Must be "brcm,nsp-gpio-a" > + > +- reg: > + Should contain the register physical address and length for each of > + GPIO base, IO control registers > + > +- #gpio-cells: > + Must be two. The first cell is the GPIO pin number (within the > + controller's pin space) and the second cell is used for the following: > + bit[0]: polarity (0 for active high and 1 for active low) > + > +- gpio-controller: > + Specifies that the node is a GPIO controller > + > +- ngpios: > + Number of gpios supported (58x25 supports 32 and 58x23 supports 24) > + > +Optional properties: > +- interrupts: > + Interrupt ID > + > +- interrupt-controller: > + Specifies that the node is an interrupt controller > + > +- gpio-ranges: > + Specifies the mapping between gpio controller and pin-controllers pins. > + This requires 4 fields in cells defined as - > + 1. Phandle of pin-controller. > + 2. GPIO base pin offset. > + 3 Pin-control base pin offset. > + 4. number of gpio pins which are linearly mapped from pin base. > + > +Supported generic PINCONF properties in child nodes: > +- pins: > + The list of pins (within the controller's own pin space) that properties > + in the node apply to. Pin names are "gpio-<pin>" > + > +- bias-disable: > + Disable pin bias > + > +- bias-pull-up: > + Enable internal pull up resistor > + > +- bias-pull-down: > + Enable internal pull down resistor > + > +- drive-strength: > + Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA) > + > +Example: > + > + gpioa: gpio@18000020 { > + compatible = "brcm,nsp-gpio-a"; > + reg = <0x18000020 0x100>, > + <0x1803f1c4 0x1c>; > + #gpio-cells = <2>; > + gpio-controller; > + ngpios = <32>; > + gpio-ranges = <&pinctrl 0 0 31>; > + interrupt-controller; > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > + > + /* Hog a few default settings */ > + pinctrl-names = "default"; > + pinctrl-0 = <&led>; > + led: led { > + pins = "gpio-1"; > + bias-pull-up; > + }; > + > + pwr: pwr { > + gpio-hog; > + gpios = <3 1>; > + output-high; > + }; > + }; > -- > 2.1.0 >
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt new file mode 100644 index 0000000..0844168 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt @@ -0,0 +1,80 @@ +Broadcom Northstar plus (NSP) GPIO/PINCONF Controller + +Required properties: +- compatible: + Must be "brcm,nsp-gpio-a" + +- reg: + Should contain the register physical address and length for each of + GPIO base, IO control registers + +- #gpio-cells: + Must be two. The first cell is the GPIO pin number (within the + controller's pin space) and the second cell is used for the following: + bit[0]: polarity (0 for active high and 1 for active low) + +- gpio-controller: + Specifies that the node is a GPIO controller + +- ngpios: + Number of gpios supported (58x25 supports 32 and 58x23 supports 24) + +Optional properties: +- interrupts: + Interrupt ID + +- interrupt-controller: + Specifies that the node is an interrupt controller + +- gpio-ranges: + Specifies the mapping between gpio controller and pin-controllers pins. + This requires 4 fields in cells defined as - + 1. Phandle of pin-controller. + 2. GPIO base pin offset. + 3 Pin-control base pin offset. + 4. number of gpio pins which are linearly mapped from pin base. + +Supported generic PINCONF properties in child nodes: +- pins: + The list of pins (within the controller's own pin space) that properties + in the node apply to. Pin names are "gpio-<pin>" + +- bias-disable: + Disable pin bias + +- bias-pull-up: + Enable internal pull up resistor + +- bias-pull-down: + Enable internal pull down resistor + +- drive-strength: + Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA) + +Example: + + gpioa: gpio@18000020 { + compatible = "brcm,nsp-gpio-a"; + reg = <0x18000020 0x100>, + <0x1803f1c4 0x1c>; + #gpio-cells = <2>; + gpio-controller; + ngpios = <32>; + gpio-ranges = <&pinctrl 0 0 31>; + interrupt-controller; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + + /* Hog a few default settings */ + pinctrl-names = "default"; + pinctrl-0 = <&led>; + led: led { + pins = "gpio-1"; + bias-pull-up; + }; + + pwr: pwr { + gpio-hog; + gpios = <3 1>; + output-high; + }; + };
Device tree binding documentation for Broadcom NSP GPIO-a Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com> --- .../devicetree/bindings/pinctrl/brcm,nsp-gpio.txt | 80 ++++++++++++++++++++++ 1 file changed, 80 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,nsp-gpio.txt