| Message ID | 1449334629-4715-6-git-send-email-anton.bondarenko.sama@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
On Sat, Dec 05, 2015 at 05:57:03PM +0100, Anton Bondarenko wrote: > Support for ECSPI loopback for IMX51, IMX53 and IMX6Q using TEST register. > > Signed-off-by: Mohsin Kazmi <mohsin_kazmi@mentor.com> > Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> > --- > drivers/spi/spi-imx.c | 19 ++++++++++++++++--- > 1 file changed, 16 insertions(+), 3 deletions(-) > > diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c > index 363276d..3525616 100644 > --- a/drivers/spi/spi-imx.c > +++ b/drivers/spi/spi-imx.c > @@ -246,6 +246,9 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi, > #define MX51_ECSPI_STAT 0x18 > #define MX51_ECSPI_STAT_RR (1 << 3) > > +#define MX51_ECSPI_TEST 0x20 > +#define MX51_ECSPI_LOOP BIT(31) > + > /* MX51 eCSPI */ > static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi, > unsigned int *fres) > @@ -316,6 +319,7 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, > u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0, dma = 0; > u32 tx_wml_cfg, rx_wml_cfg, rxt_wml_cfg; > u32 clk = config->speed_hz, delay; > + u32 lpb = 0; > > /* > * The hardware seems to have a race condition when changing modes. The > @@ -356,6 +360,12 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, > writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL); > writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG); > > + if (config->mode & SPI_LOOP) > + lpb |= MX51_ECSPI_LOOP; > + > + if ((readl(spi_imx->base + MX51_ECSPI_TEST) & MX51_ECSPI_LOOP) != lpb) > + writel(lpb, spi_imx->base + MX51_ECSPI_TEST); > + > /* > * Wait until the changes in the configuration register CONFIGREG > * propagate into the hardware. It takes exactly one tick of the > @@ -1128,6 +1138,9 @@ static int spi_imx_probe(struct platform_device *pdev) > spi_imx = spi_master_get_devdata(master); > spi_imx->bitbang.master = master; > > + spi_imx->devtype_data = of_id ? of_id->data : > + (struct spi_imx_devtype_data *)pdev->id_entry->driver_data; > + > for (i = 0; i < master->num_chipselect; i++) { > int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); > if (!gpio_is_valid(cs_gpio) && mxc_platform_info) > @@ -1154,10 +1167,10 @@ static int spi_imx_probe(struct platform_device *pdev) > spi_imx->bitbang.master->unprepare_message = spi_imx_unprepare_message; > spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; > > - init_completion(&spi_imx->xfer_done); > + if (is_imx51_ecspi(spi_imx)) > + spi_imx->bitbang.master->mode_bits |= SPI_LOOP; > > - spi_imx->devtype_data = of_id ? of_id->data : > - (struct spi_imx_devtype_data *) pdev->id_entry->driver_data; > + init_completion(&spi_imx->xfer_done); Some unrelated lines are moved in these two hunks. Is this necessary or just some leftover from development? Sascha
On 2015-12-07 10:27, Sascha Hauer wrote: > On Sat, Dec 05, 2015 at 05:57:03PM +0100, Anton Bondarenko wrote: >> Support for ECSPI loopback for IMX51, IMX53 and IMX6Q using TEST register. >> >> Signed-off-by: Mohsin Kazmi <mohsin_kazmi@mentor.com> >> Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> >> --- >> drivers/spi/spi-imx.c | 19 ++++++++++++++++--- >> 1 file changed, 16 insertions(+), 3 deletions(-) >> >> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c >> index 363276d..3525616 100644 >> --- a/drivers/spi/spi-imx.c >> +++ b/drivers/spi/spi-imx.c >> @@ -246,6 +246,9 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi, >> #define MX51_ECSPI_STAT 0x18 >> #define MX51_ECSPI_STAT_RR (1 << 3) >> >> +#define MX51_ECSPI_TEST 0x20 >> +#define MX51_ECSPI_LOOP BIT(31) >> + >> /* MX51 eCSPI */ >> static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi, >> unsigned int *fres) >> @@ -316,6 +319,7 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, >> u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0, dma = 0; >> u32 tx_wml_cfg, rx_wml_cfg, rxt_wml_cfg; >> u32 clk = config->speed_hz, delay; >> + u32 lpb = 0; >> >> /* >> * The hardware seems to have a race condition when changing modes. The >> @@ -356,6 +360,12 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, >> writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL); >> writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG); >> >> + if (config->mode & SPI_LOOP) >> + lpb |= MX51_ECSPI_LOOP; >> + >> + if ((readl(spi_imx->base + MX51_ECSPI_TEST) & MX51_ECSPI_LOOP) != lpb) >> + writel(lpb, spi_imx->base + MX51_ECSPI_TEST); >> + >> /* >> * Wait until the changes in the configuration register CONFIGREG >> * propagate into the hardware. It takes exactly one tick of the >> @@ -1128,6 +1138,9 @@ static int spi_imx_probe(struct platform_device *pdev) >> spi_imx = spi_master_get_devdata(master); >> spi_imx->bitbang.master = master; >> >> + spi_imx->devtype_data = of_id ? of_id->data : >> + (struct spi_imx_devtype_data *)pdev->id_entry->driver_data; >> + >> for (i = 0; i < master->num_chipselect; i++) { >> int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); >> if (!gpio_is_valid(cs_gpio) && mxc_platform_info) >> @@ -1154,10 +1167,10 @@ static int spi_imx_probe(struct platform_device *pdev) >> spi_imx->bitbang.master->unprepare_message = spi_imx_unprepare_message; >> spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; >> >> - init_completion(&spi_imx->xfer_done); >> + if (is_imx51_ecspi(spi_imx)) >> + spi_imx->bitbang.master->mode_bits |= SPI_LOOP; >> >> - spi_imx->devtype_data = of_id ? of_id->data : >> - (struct spi_imx_devtype_data *) pdev->id_entry->driver_data; >> + init_completion(&spi_imx->xfer_done); > > Some unrelated lines are moved in these two hunks. Is this necessary or > just some leftover from development? > > Sascha > Sascha, This is necessary because is_imx51_ecspi function is base on content of spi_imx->devtype_data (see previous commit PATCH v5 04/11). I could try to move SPI_LOOP mode bit set to avoid change for completion initialization. Regards, Anton -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index 363276d..3525616 100644 --- a/drivers/spi/spi-imx.c +++ b/drivers/spi/spi-imx.c @@ -246,6 +246,9 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi, #define MX51_ECSPI_STAT 0x18 #define MX51_ECSPI_STAT_RR (1 << 3) +#define MX51_ECSPI_TEST 0x20 +#define MX51_ECSPI_LOOP BIT(31) + /* MX51 eCSPI */ static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi, unsigned int *fres) @@ -316,6 +319,7 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0, dma = 0; u32 tx_wml_cfg, rx_wml_cfg, rxt_wml_cfg; u32 clk = config->speed_hz, delay; + u32 lpb = 0; /* * The hardware seems to have a race condition when changing modes. The @@ -356,6 +360,12 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx, writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL); writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG); + if (config->mode & SPI_LOOP) + lpb |= MX51_ECSPI_LOOP; + + if ((readl(spi_imx->base + MX51_ECSPI_TEST) & MX51_ECSPI_LOOP) != lpb) + writel(lpb, spi_imx->base + MX51_ECSPI_TEST); + /* * Wait until the changes in the configuration register CONFIGREG * propagate into the hardware. It takes exactly one tick of the @@ -1128,6 +1138,9 @@ static int spi_imx_probe(struct platform_device *pdev) spi_imx = spi_master_get_devdata(master); spi_imx->bitbang.master = master; + spi_imx->devtype_data = of_id ? of_id->data : + (struct spi_imx_devtype_data *)pdev->id_entry->driver_data; + for (i = 0; i < master->num_chipselect; i++) { int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); if (!gpio_is_valid(cs_gpio) && mxc_platform_info) @@ -1154,10 +1167,10 @@ static int spi_imx_probe(struct platform_device *pdev) spi_imx->bitbang.master->unprepare_message = spi_imx_unprepare_message; spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; - init_completion(&spi_imx->xfer_done); + if (is_imx51_ecspi(spi_imx)) + spi_imx->bitbang.master->mode_bits |= SPI_LOOP; - spi_imx->devtype_data = of_id ? of_id->data : - (struct spi_imx_devtype_data *) pdev->id_entry->driver_data; + init_completion(&spi_imx->xfer_done); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); spi_imx->base = devm_ioremap_resource(&pdev->dev, res);