| Message ID | 20151224090606.GA4879@panicking (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Sorry I mess up the email ;). Need to resend. Drop this one On Thu, Dec 24, 2015 at 10:06 AM, Michael Trimarchi <michael@amarulasolutions.com> wrote: > www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q > > Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> > --- > Test on top of ARM: dts: imx6q: clean up unused ipu2grp > > Changes in v4: > - update regulator name > - using flat pins,fsl > - move iomuxc > - add X11 license > - better alphabetic order > > Changes in v3: > - add sgtl audio support > - add ethernet gigabit tuning > - use hub reset only in usbhub and not > in otg vbus > > Changes in v2: > - add the board in alphabetic order > - remove cpu operating point > - remove simple-bus and adjust regulaotor > - add gpios to correct pinctrl > - remove no mainline binding of gpc > > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++ > arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++ > 3 files changed, 489 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts > create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index bb8fa02..7e8f29c 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-gw551x.dtb \ > imx6q-gw552x.dtb \ > imx6q-hummingboard.dtb \ > + imx6q-icore-rqs.dtb \ > imx6q-nitrogen6x.dtb \ > imx6q-phytec-pbab01.dtb \ > imx6q-rex-pro.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts > new file mode 100644 > index 0000000..0053188 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts > @@ -0,0 +1,78 @@ > +/* > + * Copyright (C) 2015 Amarula Solutions B.V. > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License > + * version 2 as published by the Free Software Foundation. > + * > + * This file is distributed in the hope that it will be useful > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > + > +#include "imx6q.dtsi" > +#include "imx6qdl-icore-rqs.dtsi" > + > +/ { > + model = "Engicam i.CoreM6 Quad SOM"; > + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q"; > + > + sound { > + compatible = "fsl,imx-audio-sgtl5000"; > + model = "imx-audio-sgtl5000"; > + ssi-controller = <&ssi1>; > + audio-codec = <&codec>; > + audio-routing = > + "MIC_IN", "Mic Jack", > + "Mic Jack", "Mic Bias", > + "Headphone Jack", "HP_OUT"; > + mux-int-port = <1>; > + mux-ext-port = <4>; > + }; > +}; > + > +&i2c3 { > + codec: sgtl5000@0a { > + compatible = "fsl,sgtl5000"; > + reg = <0x0a>; > + clocks = <&clks IMX6QDL_CLK_CKO>; > + VDDA-supply = <®_2p5v>; > + VDDIO-supply = <®_3p3v>; > + VDDD-supply = <®_1p8v>; > + }; > +}; > + > +&sata { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > new file mode 100644 > index 0000000..b984128 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > @@ -0,0 +1,410 @@ > +/* > + * Copyright (C) 2015 Amarula Solutions B.V. > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License > + * version 2 as published by the Free Software Foundation. > + * > + * This file is distributed in the hope that it will be useful > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/clock/imx6qdl-clock.h> > + > +/ { > + memory { > + reg = <0x10000000 0x80000000>; > + }; > + > + reg_1p8v: regulator-1p8v { > + compatible = "regulator-fixed"; > + regulator-name = "1P8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_2p5v: regulator-2p5v { > + compatible = "regulator-fixed"; > + regulator-name = "2P5V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_3p3v: regulator-3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3P3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_sd3_vmmc: sd3-vmmc { > + compatible = "regulator-fixed"; > + regulator-name = "P3V3_SD3_SWITCHED"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>; > + enable-active-high; > + }; > + > + reg_sd4_vmmc: sd4-vmmc { > + compatible = "regulator-fixed"; > + regulator-name = "P3V3_SD4_SWITCHED"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_usb_h1_vbus: usb-h1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_h1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_usb_otg_vbus: usb-otg-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + usb_hub: usb-hub { > + compatible = "smsc,usb3503a"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbhub>; > + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>; > + clock-names = "refclk"; > + }; > +}; > + > +&clks { > + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>; > + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>; > +}; > + > +&audmux { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux>; > + status = "okay"; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet_3>; > + phy-handle = <ð_phy>; > + phy-mode = "rgmii"; > + status = "okay"; > + mdio { > + eth_phy: ethernet-phy { > + rxc-skew-ps = <1140>; > + txc-skew-ps = <1140>; > + txen-skew-ps = <600>; > + rxdv-skew-ps = <240>; > + rxd0-skew-ps = <420>; > + rxd1-skew-ps = <600>; > + rxd2-skew-ps = <420>; > + rxd3-skew-ps = <240>; > + txd0-skew-ps = <60>; > + txd1-skew-ps = <60>; > + txd2-skew-ps = <60>; > + txd3-skew-ps = <240>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1_1>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2_2>; > + status = "okay"; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3_4>; > + status = "okay"; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie>; > + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>; > + status = "okay"; > +}; > + > +&ssi1 { > + fsl,mode = "i2s-slave"; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4_1>; > + status = "okay"; > +}; > + > +&usbh1 { > + vbus-supply = <®_usb_h1_vbus>; > + disable-over-current; > + clocks = <&clks IMX6QDL_CLK_USBOH3>; > + status = "okay"; > +}; > + > +&usbotg { > + vbus-supply = <®_usb_otg_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg_2>; > + disable-over-current; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1_1>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc3_2>; > + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>; > + vmcc-supply = <®_sd3_vmmc>; > + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; > + bus-witdh=<4>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&usdhc4 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc4_1>; > + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>; > + vmcc-supply = <®_sd4_vmmc>; > + bus-witdh=<8>; > + no-1-8-v; > + non-removable; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_audmux: audmux { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0 > + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0 > + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0 > + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0 > + >; > + }; > + > + pinctrl_enet_3: enetgrp-3 { > + fsl,pins = < > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 > + >; > + }; > + > + pinctrl_i2c1_1: i2c1grp-1 { > + fsl,pins = < > + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 > + >; > + }; > + > + pinctrl_i2c2_2: i2c2grp-2 { > + fsl,pins = < > + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 > + >; > + }; > + > + pinctrl_i2c3_4: i2c3grp-4 { > + fsl,pins = < > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 > + >; > + }; > + > + pinctrl_pcie: pciegrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */ > + >; > + }; > + > + pinctrl_uart4_1: uart4grp-1 { > + fsl,pins = < > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 > + >; > + }; > + > + pinctrl_usbhub: usbhubgrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */ > + >; > + }; > + > + pinctrl_usbotg_2: usbotggrp-2 { > + fsl,pins = < > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 > + >; > + }; > + > + pinctrl_usdhc1_1: usdhc1grp-1 { > + fsl,pins = < > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071 > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071 > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071 > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071 > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071 > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071 > + >; > + }; > + > + pinctrl_usdhc3_2: usdhc3grp-2 { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070 > + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */ > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */ > + >; > + }; > + > + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1 > + >; > + }; > + > + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9 > + >; > + }; > + > + pinctrl_usdhc4_1: usdhc4grp-1 { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070 > + >; > + }; > + > + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1 > + >; > + }; > + > + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9 > + >; > + }; > +}; > -- > 2.6.4 > > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++ > arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++ > 3 files changed, 489 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts > create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index bb8fa02..7e8f29c 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-gw551x.dtb \ > imx6q-gw552x.dtb \ > imx6q-hummingboard.dtb \ > + imx6q-icore-rqs.dtb \ > imx6q-nitrogen6x.dtb \ > imx6q-phytec-pbab01.dtb \ > imx6q-rex-pro.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts > new file mode 100644 > index 0000000..0053188 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts > @@ -0,0 +1,78 @@ > +/* > + * Copyright (C) 2015 Amarula Solutions B.V. > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License > + * version 2 as published by the Free Software Foundation. > + * > + * This file is distributed in the hope that it will be useful > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > + > +#include "imx6q.dtsi" > +#include "imx6qdl-icore-rqs.dtsi" > + > +/ { > + model = "Engicam i.CoreM6 Quad SOM"; > + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q"; > + > + sound { > + compatible = "fsl,imx-audio-sgtl5000"; > + model = "imx-audio-sgtl5000"; > + ssi-controller = <&ssi1>; > + audio-codec = <&codec>; > + audio-routing = > + "MIC_IN", "Mic Jack", > + "Mic Jack", "Mic Bias", > + "Headphone Jack", "HP_OUT"; > + mux-int-port = <1>; > + mux-ext-port = <4>; > + }; > +}; > + > +&i2c3 { > + codec: sgtl5000@0a { > + compatible = "fsl,sgtl5000"; > + reg = <0x0a>; > + clocks = <&clks IMX6QDL_CLK_CKO>; > + VDDA-supply = <®_2p5v>; > + VDDIO-supply = <®_3p3v>; > + VDDD-supply = <®_1p8v>; > + }; > +}; > + > +&sata { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > new file mode 100644 > index 0000000..b984128 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi > @@ -0,0 +1,410 @@ > +/* > + * Copyright (C) 2015 Amarula Solutions B.V. > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License > + * version 2 as published by the Free Software Foundation. > + * > + * This file is distributed in the hope that it will be useful > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/clock/imx6qdl-clock.h> > + > +/ { > + memory { > + reg = <0x10000000 0x80000000>; > + }; > + > + reg_1p8v: regulator-1p8v { > + compatible = "regulator-fixed"; > + regulator-name = "1P8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_2p5v: regulator-2p5v { > + compatible = "regulator-fixed"; > + regulator-name = "2P5V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_3p3v: regulator-3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3P3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_sd3_vmmc: sd3-vmmc { > + compatible = "regulator-fixed"; > + regulator-name = "P3V3_SD3_SWITCHED"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>; > + enable-active-high; > + }; > + > + reg_sd4_vmmc: sd4-vmmc { > + compatible = "regulator-fixed"; > + regulator-name = "P3V3_SD4_SWITCHED"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_usb_h1_vbus: usb-h1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_h1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + reg_usb_otg_vbus: usb-otg-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + usb_hub: usb-hub { > + compatible = "smsc,usb3503a"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbhub>; > + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>; > + clock-names = "refclk"; > + }; > +}; > + > +&clks { > + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>; > + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>; > +}; > + > +&audmux { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux>; > + status = "okay"; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet_3>; > + phy-handle = <ð_phy>; > + phy-mode = "rgmii"; > + status = "okay"; > + mdio { > + eth_phy: ethernet-phy { > + rxc-skew-ps = <1140>; > + txc-skew-ps = <1140>; > + txen-skew-ps = <600>; > + rxdv-skew-ps = <240>; > + rxd0-skew-ps = <420>; > + rxd1-skew-ps = <600>; > + rxd2-skew-ps = <420>; > + rxd3-skew-ps = <240>; > + txd0-skew-ps = <60>; > + txd1-skew-ps = <60>; > + txd2-skew-ps = <60>; > + txd3-skew-ps = <240>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1_1>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2_2>; > + status = "okay"; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3_4>; > + status = "okay"; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie>; > + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>; > + status = "okay"; > +}; > + > +&ssi1 { > + fsl,mode = "i2s-slave"; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4_1>; > + status = "okay"; > +}; > + > +&usbh1 { > + vbus-supply = <®_usb_h1_vbus>; > + disable-over-current; > + clocks = <&clks IMX6QDL_CLK_USBOH3>; > + status = "okay"; > +}; > + > +&usbotg { > + vbus-supply = <®_usb_otg_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg_2>; > + disable-over-current; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1_1>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc3_2>; > + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>; > + vmcc-supply = <®_sd3_vmmc>; > + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; > + bus-witdh=<4>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&usdhc4 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc4_1>; > + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>; > + vmcc-supply = <®_sd4_vmmc>; > + bus-witdh=<8>; > + no-1-8-v; > + non-removable; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_audmux: audmux { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0 > + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0 > + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0 > + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0 > + >; > + }; > + > + pinctrl_enet_3: enetgrp-3 { > + fsl,pins = < > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 > + >; > + }; > + > + pinctrl_i2c1_1: i2c1grp-1 { > + fsl,pins = < > + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 > + >; > + }; > + > + pinctrl_i2c2_2: i2c2grp-2 { > + fsl,pins = < > + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 > + >; > + }; > + > + pinctrl_i2c3_4: i2c3grp-4 { > + fsl,pins = < > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 > + >; > + }; > + > + pinctrl_pcie: pciegrp { > + fsl,pins = < > + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */ > + >; > + }; > + > + pinctrl_uart4_1: uart4grp-1 { > + fsl,pins = < > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 > + >; > + }; > + > + pinctrl_usbhub: usbhubgrp { > + fsl,pins = < > + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */ > + >; > + }; > + > + pinctrl_usbotg_2: usbotggrp-2 { > + fsl,pins = < > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 > + >; > + }; > + > + pinctrl_usdhc1_1: usdhc1grp-1 { > + fsl,pins = < > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071 > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071 > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071 > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071 > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071 > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071 > + >; > + }; > + > + pinctrl_usdhc3_2: usdhc3grp-2 { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070 > + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */ > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */ > + >; > + }; > + > + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1 > + >; > + }; > + > + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9 > + >; > + }; > + > + pinctrl_usdhc4_1: usdhc4grp-1 { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070 > + >; > + }; > + > + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1 > + >; > + }; > + > + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz { > + fsl,pins = < > + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9 > + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9 > + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9 > + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9 > + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9 > + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9 > + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9 > + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9 > + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9 > + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9 > + >; > + }; > +}; > -- > 2.6.4 > > -- > | Michael Nazzareno Trimarchi Amarula Solutions BV | > | COO - Founder Cruquiuskade 47 | > | +31(0)851119172 Amsterdam 1018 AM NL | > | [`as] http://www.amarulasolutions.com |
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bb8fa02..7e8f29c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-hummingboard.dtb \ + imx6q-icore-rqs.dtb \ imx6q-nitrogen6x.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts new file mode 100644 index 0000000..0053188 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts @@ -0,0 +1,78 @@ +/* + * Copyright (C) 2015 Amarula Solutions B.V. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "imx6q.dtsi" +#include "imx6qdl-icore-rqs.dtsi" + +/ { + model = "Engicam i.CoreM6 Quad SOM"; + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q"; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "imx-audio-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&i2c3 { + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks IMX6QDL_CLK_CKO>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + VDDD-supply = <®_1p8v>; + }; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi new file mode 100644 index 0000000..b984128 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi @@ -0,0 +1,410 @@ +/* + * Copyright (C) 2015 Amarula Solutions B.V. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clock/imx6qdl-clock.h> + +/ { + memory { + reg = <0x10000000 0x80000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sd3_vmmc: sd3-vmmc { + compatible = "regulator-fixed"; + regulator-name = "P3V3_SD3_SWITCHED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>; + enable-active-high; + }; + + reg_sd4_vmmc: sd4-vmmc { + compatible = "regulator-fixed"; + regulator-name = "P3V3_SD4_SWITCHED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_usb_h1_vbus: usb-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_usb_otg_vbus: usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + usb_hub: usb-hub { + compatible = "smsc,usb3503a"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbhub>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>; + clock-names = "refclk"; + }; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_3>; + phy-handle = <ð_phy>; + phy-mode = "rgmii"; + status = "okay"; + mdio { + eth_phy: ethernet-phy { + rxc-skew-ps = <1140>; + txc-skew-ps = <1140>; + txen-skew-ps = <600>; + rxdv-skew-ps = <240>; + rxd0-skew-ps = <420>; + rxd1-skew-ps = <600>; + rxd2-skew-ps = <420>; + rxd3-skew-ps = <240>; + txd0-skew-ps = <60>; + txd1-skew-ps = <60>; + txd2-skew-ps = <60>; + txd3-skew-ps = <240>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_2>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_4>; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + disable-over-current; + clocks = <&clks IMX6QDL_CLK_USBOH3>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_2>; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1_1>; + no-1-8-v; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3_2>; + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>; + vmcc-supply = <®_sd3_vmmc>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + bus-witdh=<4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc4_1>; + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>; + vmcc-supply = <®_sd4_vmmc>; + bus-witdh=<8>; + no-1-8-v; + non-removable; + status = "okay"; +}; + +&iomuxc { + pinctrl_audmux: audmux { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0 + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0 + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0 + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0 + >; + }; + + pinctrl_enet_3: enetgrp-3 { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + >; + }; + + pinctrl_i2c1_1: i2c1grp-1 { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2_2: i2c2grp-2 { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_4: i2c3grp-4 { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */ + >; + }; + + pinctrl_uart4_1: uart4grp-1 { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbhub: usbhubgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */ + >; + }; + + pinctrl_usbotg_2: usbotggrp-2 { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc1_1: usdhc1grp-1 { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071 + >; + }; + + pinctrl_usdhc3_2: usdhc3grp-2 { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */ + >; + }; + + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1 + >; + }; + + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9 + >; + }; + + pinctrl_usdhc4_1: usdhc4grp-1 { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070 + >; + }; + + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1 + >; + }; + + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9 + >; + }; +}; -- 2.6.4 arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++ arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++ 3 files changed, 489 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bb8fa02..7e8f29c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-hummingboard.dtb \ + imx6q-icore-rqs.dtb \ imx6q-nitrogen6x.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts new file mode 100644 index 0000000..0053188 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts @@ -0,0 +1,78 @@ +/* + * Copyright (C) 2015 Amarula Solutions B.V. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "imx6q.dtsi" +#include "imx6qdl-icore-rqs.dtsi" + +/ { + model = "Engicam i.CoreM6 Quad SOM"; + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q"; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "imx-audio-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&i2c3 { + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks IMX6QDL_CLK_CKO>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + VDDD-supply = <®_1p8v>; + }; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi new file mode 100644 index 0000000..b984128 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi @@ -0,0 +1,410 @@ +/* + * Copyright (C) 2015 Amarula Solutions B.V. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clock/imx6qdl-clock.h> + +/ { + memory { + reg = <0x10000000 0x80000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sd3_vmmc: sd3-vmmc { + compatible = "regulator-fixed"; + regulator-name = "P3V3_SD3_SWITCHED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>; + enable-active-high; + }; + + reg_sd4_vmmc: sd4-vmmc { + compatible = "regulator-fixed"; + regulator-name = "P3V3_SD4_SWITCHED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_usb_h1_vbus: usb-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_usb_otg_vbus: usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + usb_hub: usb-hub { + compatible = "smsc,usb3503a"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbhub>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>; + clock-names = "refclk"; + }; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_3>; + phy-handle = <ð_phy>; + phy-mode = "rgmii"; + status = "okay"; + mdio { + eth_phy: ethernet-phy { + rxc-skew-ps = <1140>; + txc-skew-ps = <1140>; + txen-skew-ps = <600>; + rxdv-skew-ps = <240>; + rxd0-skew-ps = <420>; + rxd1-skew-ps = <600>; + rxd2-skew-ps = <420>; + rxd3-skew-ps = <240>; + txd0-skew-ps = <60>; + txd1-skew-ps = <60>; + txd2-skew-ps = <60>; + txd3-skew-ps = <240>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_2>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_4>; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_1>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + disable-over-current; + clocks = <&clks IMX6QDL_CLK_USBOH3>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_2>; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1_1>; + no-1-8-v; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3_2>; + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>; + vmcc-supply = <®_sd3_vmmc>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + bus-witdh=<4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc4_1>; + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>; + vmcc-supply = <®_sd4_vmmc>; + bus-witdh=<8>; + no-1-8-v; + non-removable; + status = "okay"; +}; + +&iomuxc { + pinctrl_audmux: audmux { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0 + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0 + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0 + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0 + >; + }; + + pinctrl_enet_3: enetgrp-3 { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + >; + }; + + pinctrl_i2c1_1: i2c1grp-1 { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2_2: i2c2grp-2 { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_4: i2c3grp-4 { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */ + >; + }; + + pinctrl_uart4_1: uart4grp-1 { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbhub: usbhubgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1f059 /* HUB USB Reset */ + >; + }; + + pinctrl_usbotg_2: usbotggrp-2 { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc1_1: usdhc1grp-1 { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071 + >; + }; + + pinctrl_usdhc3_2: usdhc3grp-2 { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17070 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10070 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1f059 /* CD */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f059 /* PWR */ + >; + }; + + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B1 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B1 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1 + >; + }; + + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9 + >; + }; + + pinctrl_usdhc4_1: usdhc4grp-1 { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070 + >; + }; + + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170B1 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100B1 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1 + >; + }; + + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x170F9 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x100F9 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9 + >; + }; +};
www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> --- Test on top of ARM: dts: imx6q: clean up unused ipu2grp Changes in v4: - update regulator name - using flat pins,fsl - move iomuxc - add X11 license - better alphabetic order Changes in v3: - add sgtl audio support - add ethernet gigabit tuning - use hub reset only in usbhub and not in otg vbus Changes in v2: - add the board in alphabetic order - remove cpu operating point - remove simple-bus and adjust regulaotor - add gpios to correct pinctrl - remove no mainline binding of gpc arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-icore-rqs.dts | 78 ++++++ arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++ 3 files changed, 489 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi