@@ -22,6 +22,7 @@ Required properties for iomux controller:
- compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
"rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
"rockchip,rk3288-pinctrl", "rockchip,rk3368-pinctrl"
+ "rockchip,rk3399-pinctrl"
- rockchip,grf: phandle referencing a syscon providing the
"general register files"
@@ -64,6 +64,7 @@ enum rockchip_pinctrl_type {
RK3188,
RK3288,
RK3368,
+ RK3399,
};
/**
@@ -86,6 +87,31 @@ struct rockchip_iomux {
};
/**
+ * enum type index corresponding to rockchip_perpin_drv_list arrays index.
+ */
+enum rockchip_pin_drv_type {
+ DRV_TYPE_IO_DEFAULT = 0,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_ONLY,
+ DRV_TYPE_IO_1V8_3V0_AUTO,
+ DRV_TYPE_IO_3V3_ONLY,
+ DRV_TYPE_MAX
+};
+
+/**
+ * @drv_type: drive strength variant using rockchip_perpin_drv_type
+ * @offset: if initialized to -1 it will be autocalculated, by specifying
+ * an initial offset value the relevant source offset can be reset
+ * to a new value for autocalculating the following drive strength
+ * registers. if used chips own cal_drv func instead to calculate
+ * registers offset, the variant could be ignored.
+ */
+struct rockchip_drv {
+ enum rockchip_pin_drv_type drv_type;
+ int offset;
+};
+
+/**
* @reg_base: register base of the gpio bank
* @reg_pull: optional separate register for additional pull settings
* @clk: clock of the gpio bank
@@ -96,6 +122,7 @@ struct rockchip_iomux {
* @name: name of the bank
* @bank_num: number of the bank, to account for holes
* @iomux: array describing the 4 iomux sources of the bank
+ * @drv: array describing the 4 drive strength sources of the bank
* @valid: are all necessary informations present
* @of_node: dt node of this bank
* @drvdata: common pinctrl basedata
@@ -115,6 +142,7 @@ struct rockchip_pin_bank {
char *name;
u8 bank_num;
struct rockchip_iomux iomux[4];
+ struct rockchip_drv drv[4];
bool valid;
struct device_node *of_node;
struct rockchip_pinctrl *drvdata;
@@ -151,6 +179,47 @@ struct rockchip_pin_bank {
}, \
}
+#define PIN_BANK_DRV_FLAGS(id, pins, label, type0, type1, type2, type3) \
+ { \
+ .bank_num = id, \
+ .nr_pins = pins, \
+ .name = label, \
+ .iomux = { \
+ { .offset = -1 }, \
+ { .offset = -1 }, \
+ { .offset = -1 }, \
+ { .offset = -1 }, \
+ }, \
+ .drv = { \
+ { .drv_type = type0, .offset = -1 }, \
+ { .drv_type = type1, .offset = -1 }, \
+ { .drv_type = type2, .offset = -1 }, \
+ { .drv_type = type3, .offset = -1 }, \
+ }, \
+ }
+
+#define PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(id, pins, label, iom0, iom1, \
+ iom2, iom3, drv0, drv1, drv2, \
+ drv3, offset0, offset1, \
+ offset2, offset3) \
+ { \
+ .bank_num = id, \
+ .nr_pins = pins, \
+ .name = label, \
+ .iomux = { \
+ { .type = iom0, .offset = -1 }, \
+ { .type = iom1, .offset = -1 }, \
+ { .type = iom2, .offset = -1 }, \
+ { .type = iom3, .offset = -1 }, \
+ }, \
+ .drv = { \
+ { .drv_type = drv0, .offset = offset0 }, \
+ { .drv_type = drv1, .offset = offset1 }, \
+ { .drv_type = drv2, .offset = offset2 }, \
+ { .drv_type = drv3, .offset = offset3 }, \
+ }, \
+ }
+
/**
*/
struct rockchip_pin_ctrl {
@@ -161,6 +230,9 @@ struct rockchip_pin_ctrl {
enum rockchip_pinctrl_type type;
int grf_mux_offset;
int pmu_mux_offset;
+ int grf_drv_offset;
+ int pmu_drv_offset;
+
void (*pull_calc_reg)(struct rockchip_pin_bank *bank,
int pin_num, struct regmap **regmap,
int *reg, u8 *bit);
@@ -676,7 +748,71 @@ static void rk3368_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
}
}
-static int rockchip_perpin_drv_list[] = { 2, 4, 8, 12 };
+#define RK3399_PULL_GRF_OFFSET 0xe040
+#define RK3399_PULL_PMU_OFFSET 0x40
+#define RK3399_DRV_3BITS_PER_PIN 3
+
+static void rk3399_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ /* The bank0:16 and bank1:32 pins are located in PMU */
+ if ((bank->bank_num == 0) || (bank->bank_num == 1)) {
+ *regmap = info->regmap_pmu;
+ *reg = RK3399_PULL_PMU_OFFSET;
+
+ *reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
+
+ *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
+ *bit = pin_num % RK3188_PULL_PINS_PER_REG;
+ *bit *= RK3188_PULL_BITS_PER_PIN;
+ } else {
+ *regmap = info->regmap_base;
+ *reg = RK3399_PULL_GRF_OFFSET;
+
+ /* correct the offset, as we're starting with the 3rd bank */
+ *reg -= 0x20;
+ *reg += bank->bank_num * RK3188_PULL_BANK_STRIDE;
+ *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4);
+
+ *bit = (pin_num % RK3188_PULL_PINS_PER_REG);
+ *bit *= RK3188_PULL_BITS_PER_PIN;
+ }
+}
+
+static void rk3399_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+ int drv_num = (pin_num / 8);
+
+ /* The bank0:16 and bank1:32 pins are located in PMU */
+ if ((bank->bank_num == 0) || (bank->bank_num == 1))
+ *regmap = info->regmap_pmu;
+ else
+ *regmap = info->regmap_base;
+
+ *reg = bank->drv[drv_num].offset;
+ if ((bank->drv[drv_num].drv_type == DRV_TYPE_IO_1V8_3V0_AUTO) ||
+ (bank->drv[drv_num].drv_type == DRV_TYPE_IO_3V3_ONLY)) {
+ if ((pin_num % 8) >= 6)
+ *reg += 0x4;
+ *bit = ((pin_num % 8) * 3) % 16;
+ } else {
+ *bit = (pin_num % 8) * 2;
+ }
+}
+
+static int rockchip_perpin_drv_list[DRV_TYPE_MAX][8] = {
+ { 2, 4, 8, 12, -1, -1, -1, -1 },
+ { 3, 6, 9, 12, -1, -1, -1, -1 },
+ { 5, 10, 15, 20, -1, -1, -1, -1 },
+ { 4, 6, 8, 10, 12, 14, 16, 18 },
+ { 4, 7, 10, 13, 16, 19, 22, 26 }
+};
static int rockchip_get_drive_perpin(struct rockchip_pin_bank *bank,
int pin_num)
@@ -685,19 +821,60 @@ static int rockchip_get_drive_perpin(struct rockchip_pin_bank *bank,
struct rockchip_pin_ctrl *ctrl = info->ctrl;
struct regmap *regmap;
int reg, ret;
- u32 data;
+ u32 data, temp, rmask_bits;
u8 bit;
+ int drv_type = bank->drv[pin_num / 8].drv_type;
ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit);
+ switch (drv_type) {
+ case DRV_TYPE_IO_1V8_3V0_AUTO:
+ case DRV_TYPE_IO_3V3_ONLY:
+ if (RK3399_DRV_3BITS_PER_PIN + bit >= 16) {
+ /* need to read regs twice */
+ ret = regmap_read(regmap, reg, &temp);
+ if (ret)
+ return ret;
+
+ temp >>= bit;
+ rmask_bits = 16 - bit;
+ temp &= (1 << rmask_bits) - 1;
+
+ reg = reg + 0x4;
+ ret = regmap_read(regmap, reg, &data);
+ if (ret)
+ return ret;
+
+ rmask_bits = RK3399_DRV_3BITS_PER_PIN
+ + bit - 16;
+ data &= (1 << rmask_bits) - 1;
+ data <<= 16 - bit;
+ data |= temp;
+
+ return rockchip_perpin_drv_list[drv_type][data];
+ }
+
+ rmask_bits = RK3399_DRV_3BITS_PER_PIN;
+ break;
+ case DRV_TYPE_IO_DEFAULT:
+ case DRV_TYPE_IO_1V8_OR_3V0:
+ case DRV_TYPE_IO_1V8_ONLY:
+ rmask_bits = RK3288_DRV_BITS_PER_PIN;
+ break;
+ default:
+ dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
+ drv_type);
+ return -EINVAL;
+ }
+
ret = regmap_read(regmap, reg, &data);
if (ret)
return ret;
data >>= bit;
- data &= (1 << RK3288_DRV_BITS_PER_PIN) - 1;
+ data &= (1 << rmask_bits) - 1;
- return rockchip_perpin_drv_list[data];
+ return rockchip_perpin_drv_list[drv_type][data];
}
static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
@@ -708,16 +885,23 @@ static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
struct regmap *regmap;
unsigned long flags;
int reg, ret, i;
- u32 data, rmask;
+ u32 data, rmask, rmask_bits;
u8 bit;
+ int drv_type = bank->drv[pin_num / 8].drv_type;
+
+ dev_dbg(info->dev, "setting drive of GPIO%d-%d to %d\n",
+ bank->bank_num, pin_num, strength);
ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit);
ret = -EINVAL;
- for (i = 0; i < ARRAY_SIZE(rockchip_perpin_drv_list); i++) {
- if (rockchip_perpin_drv_list[i] == strength) {
+ for (i = 0; i < ARRAY_SIZE(rockchip_perpin_drv_list[drv_type]); i++) {
+ if (rockchip_perpin_drv_list[drv_type][i] == strength) {
ret = i;
break;
+ } else if (rockchip_perpin_drv_list[drv_type][i] < 0) {
+ ret = rockchip_perpin_drv_list[drv_type][i];
+ break;
}
}
@@ -729,8 +913,44 @@ static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
spin_lock_irqsave(&bank->slock, flags);
+ switch (drv_type) {
+ case DRV_TYPE_IO_1V8_3V0_AUTO:
+ case DRV_TYPE_IO_3V3_ONLY:
+ if (RK3399_DRV_3BITS_PER_PIN + bit >= 16) {
+ /* need to write regs twice */
+ rmask_bits = 16 - bit;
+ /* enable the write to the equivalent lower bits */
+ data = ((1 << rmask_bits) - 1) << (bit + 16);
+ rmask = data | (data >> 16);
+ ret &= (1 << rmask_bits) - 1;
+ data |= (ret << bit);
+
+ ret = regmap_update_bits(regmap, reg, rmask, data);
+ if (ret)
+ return ret;
+
+ ret = i >> rmask_bits;
+ rmask_bits = RK3399_DRV_3BITS_PER_PIN + bit - 16;
+ reg = reg + 0x4;
+ bit = 0;
+ } else {
+ rmask_bits = RK3399_DRV_3BITS_PER_PIN;
+ }
+ break;
+ case DRV_TYPE_IO_DEFAULT:
+ case DRV_TYPE_IO_1V8_OR_3V0:
+ case DRV_TYPE_IO_1V8_ONLY:
+ rmask_bits = RK3288_DRV_BITS_PER_PIN;
+ break;
+ default:
+ dev_err(info->dev, "unsupported pinctrl drive type: %d\n",
+ drv_type);
+ return -EINVAL;
+
+ }
+
/* enable the write to the equivalent lower bits */
- data = ((1 << RK3288_DRV_BITS_PER_PIN) - 1) << (bit + 16);
+ data = ((1 << rmask_bits) - 1) << (bit + 16);
rmask = data | (data >> 16);
data |= (ret << bit);
@@ -767,6 +987,7 @@ static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num)
case RK3188:
case RK3288:
case RK3368:
+ case RK3399:
data >>= bit;
data &= (1 << RK3188_PULL_BITS_PER_PIN) - 1;
@@ -823,6 +1044,7 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
case RK3188:
case RK3288:
case RK3368:
+ case RK3399:
spin_lock_irqsave(&bank->slock, flags);
/* enable the write to the equivalent lower bits */
@@ -1003,6 +1225,7 @@ static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl,
case RK3188:
case RK3288:
case RK3368:
+ case RK3399:
return (pull != PIN_CONFIG_BIAS_PULL_PIN_DEFAULT);
}
@@ -1860,7 +2083,7 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
struct device_node *np;
struct rockchip_pin_ctrl *ctrl;
struct rockchip_pin_bank *bank;
- int grf_offs, pmu_offs, i, j;
+ int grf_offs, pmu_offs, drv_grf_offs, drv_pmu_offs, i, j;
match = of_match_node(rockchip_pinctrl_dt_match, node);
ctrl = (struct rockchip_pin_ctrl *)match->data;
@@ -1884,6 +2107,8 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
grf_offs = ctrl->grf_mux_offset;
pmu_offs = ctrl->pmu_mux_offset;
+ drv_pmu_offs = ctrl->pmu_drv_offset;
+ drv_grf_offs = ctrl->grf_drv_offset;
bank = ctrl->pin_banks;
for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
int bank_pins = 0;
@@ -1893,15 +2118,16 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
bank->pin_base = ctrl->nr_pins;
ctrl->nr_pins += bank->nr_pins;
- /* calculate iomux offsets */
+ /* calculate iomux and drv offsets */
for (j = 0; j < 4; j++) {
struct rockchip_iomux *iom = &bank->iomux[j];
+ struct rockchip_drv *drv = &bank->drv[j];
int inc;
if (bank_pins >= bank->nr_pins)
break;
- /* preset offset value, set new start value */
+ /* preset iomux offset value, set new start value */
if (iom->offset >= 0) {
if (iom->type & IOMUX_SOURCE_PMU)
pmu_offs = iom->offset;
@@ -1912,8 +2138,19 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
pmu_offs : grf_offs;
}
- dev_dbg(d->dev, "bank %d, iomux %d has offset 0x%x\n",
- i, j, iom->offset);
+ /* preset drv offset value, set new start value */
+ if (drv->offset >= 0) {
+ if (iom->type & IOMUX_SOURCE_PMU)
+ drv_pmu_offs = drv->offset;
+ else
+ drv_grf_offs = drv->offset;
+ } else { /* set current drv offset */
+ drv->offset = (iom->type & IOMUX_SOURCE_PMU) ?
+ drv_pmu_offs : drv_grf_offs;
+ }
+
+ dev_dbg(d->dev, "bank %d, iomux %d has iom_offset 0x%x drv_offset 0x%x\n",
+ i, j, iom->offset, drv->offset);
/*
* Increase offset according to iomux width.
@@ -1925,6 +2162,21 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
else
grf_offs += inc;
+ /*
+ * Increase offset according to drv width.
+ * 3bit drive-strenth'es are spread over two registers.
+ */
+ if ((drv->drv_type == DRV_TYPE_IO_1V8_3V0_AUTO) ||
+ (drv->drv_type == DRV_TYPE_IO_3V3_ONLY))
+ inc = 8;
+ else
+ inc = 4;
+
+ if (iom->type & IOMUX_SOURCE_PMU)
+ drv_pmu_offs += inc;
+ else
+ drv_grf_offs += inc;
+
bank_pins += 8;
}
}
@@ -2208,6 +2460,62 @@ static struct rockchip_pin_ctrl rk3368_pin_ctrl = {
.drv_calc_reg = rk3368_calc_drv_reg_and_bit,
};
+static struct rockchip_pin_bank rk3399_pin_banks[] = {
+ PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(0, 32, "gpio0", IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ DRV_TYPE_IO_1V8_ONLY,
+ DRV_TYPE_IO_1V8_ONLY,
+ 0,
+ 0,
+ 0x0,
+ 0x8,
+ -1,
+ -1
+ ),
+ PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(1, 32, "gpio1", IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ IOMUX_SOURCE_PMU,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ 0x20,
+ 0x28,
+ 0x30,
+ 0x38
+ ),
+ PIN_BANK_DRV_FLAGS(2, 32, "gpio2", DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_ONLY,
+ DRV_TYPE_IO_1V8_ONLY
+ ),
+ PIN_BANK_DRV_FLAGS(3, 32, "gpio3", DRV_TYPE_IO_3V3_ONLY,
+ DRV_TYPE_IO_3V3_ONLY,
+ DRV_TYPE_IO_3V3_ONLY,
+ DRV_TYPE_IO_1V8_OR_3V0
+ ),
+ PIN_BANK_DRV_FLAGS(4, 32, "gpio4", DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_3V0_AUTO,
+ DRV_TYPE_IO_1V8_OR_3V0,
+ DRV_TYPE_IO_1V8_OR_3V0
+ ),
+};
+
+static struct rockchip_pin_ctrl rk3399_pin_ctrl = {
+ .pin_banks = rk3399_pin_banks,
+ .nr_banks = ARRAY_SIZE(rk3399_pin_banks),
+ .label = "RK3399-GPIO",
+ .type = RK3399,
+ .grf_mux_offset = 0xe000,
+ .pmu_mux_offset = 0x0,
+ .grf_drv_offset = 0xe100,
+ .pmu_drv_offset = 0x80,
+ .pull_calc_reg = rk3399_calc_pull_reg_and_bit,
+ .drv_calc_reg = rk3399_calc_drv_reg_and_bit,
+};
static const struct of_device_id rockchip_pinctrl_dt_match[] = {
{ .compatible = "rockchip,rk2928-pinctrl",
@@ -2224,6 +2532,8 @@ static const struct of_device_id rockchip_pinctrl_dt_match[] = {
.data = (void *)&rk3288_pin_ctrl },
{ .compatible = "rockchip,rk3368-pinctrl",
.data = (void *)&rk3368_pin_ctrl },
+ { .compatible = "rockchip,rk3399-pinctrl",
+ .data = (void *)&rk3399_pin_ctrl },
{},
};
MODULE_DEVICE_TABLE(of, rockchip_pinctrl_dt_match);