@@ -24,15 +24,20 @@
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/opp.h>
+#include <linux/i2c.h>
+#include <linux/mm.h>
+#include <linux/videodev2.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/mmc/host.h>
-
+#include <linux/gpio.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
+#include <media/mt9p031.h>
+
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -47,12 +52,18 @@
#include <plat/nand.h>
#include <plat/usb.h>
#include <plat/omap_device.h>
+#include <plat/i2c.h>
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
#include "pm.h"
+#include "devices.h"
+#include "../../../drivers/media/video/omap3isp/isp.h"
+#include "../../../drivers/media/video/omap3isp/ispreg.h"
+#define MT9P031_RESET_GPIO 98
+#define MT9P031_XCLK ISP_XCLK_A
#define NAND_BLOCK_SIZE SZ_128K
/*
@@ -273,6 +284,44 @@ static struct regulator_consumer_supply beagle_vsim_supply = {
static struct gpio_led gpio_leds[];
+static struct regulator_consumer_supply beagle_vaux3_supply = {
+ .supply = "cam_1v8",
+};
+
+static struct regulator_consumer_supply beagle_vaux4_supply = {
+ .supply = "cam_2v8",
+};
+
+/* VAUX3 for CAM_1V8 */
+static struct regulator_init_data beagle_vaux3 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &beagle_vaux3_supply,
+};
+
+/* VAUX4 for CAM_2V8 */
+static struct regulator_init_data beagle_vaux4 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &beagle_vaux4_supply,
+};
+
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -309,6 +358,15 @@ static int beagle_twl_gpio_setup(struct device *dev,
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
+ if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+ /*
+ * Power on camera interface - only on pre-production, not
+ * needed on production boards
+ */
+ gpio_request(gpio + 2, "CAM_EN");
+ gpio_direction_output(gpio + 2, 1);
+ }
+
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
@@ -451,6 +509,8 @@ static struct twl4030_platform_data beagle_twldata = {
.vsim = &beagle_vsim,
.vdac = &beagle_vdac,
.vpll2 = &beagle_vpll2,
+ .vaux3 = &beagle_vaux3,
+ .vaux4 = &beagle_vaux4,
};
static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
@@ -463,15 +523,16 @@ static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
};
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
- {
- I2C_BOARD_INFO("eeprom", 0x50),
- },
+ {
+ I2C_BOARD_INFO("eeprom", 0x50),
+ },
};
static int __init omap3_beagle_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
ARRAY_SIZE(beagle_i2c_boardinfo));
+ omap_register_i2c_bus(2, 100, NULL, 0); /* Enable I2C2 for camera */
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
@@ -654,6 +715,62 @@ static void __init beagle_opp_init(void)
return;
}
+extern struct platform_device omap3isp_device;
+
+static int beagle_cam_set_xclk(struct v4l2_subdev *subdev, int hz)
+{
+ struct isp_device *isp = platform_get_drvdata(&omap3isp_device);
+ int ret;
+
+ ret = isp->platform_cb.set_xclk(isp, hz, MT9P031_XCLK);
+ return 0;
+}
+
+static int beagle_cam_reset(struct v4l2_subdev *subdev, int active)
+{
+ /* Set RESET_BAR to !active */
+ gpio_set_value(MT9P031_RESET_GPIO, !active);
+
+ return 0;
+}
+
+static struct mt9p031_platform_data beagle_mt9p031_platform_data = {
+ .set_xclk = beagle_cam_set_xclk,
+ .reset = beagle_cam_reset,
+};
+
+static struct i2c_board_info mt9p031_camera_i2c_device = {
+ I2C_BOARD_INFO("mt9p031", 0x48),
+ .platform_data = &beagle_mt9p031_platform_data,
+};
+
+static struct isp_subdev_i2c_board_info mt9p031_camera_subdevs[] = {
+ {
+ .board_info = &mt9p031_camera_i2c_device,
+ .i2c_adapter_id = 2,
+ },
+ { NULL, 0, },
+};
+
+static struct isp_v4l2_subdevs_group beagle_camera_subdevs[] = {
+ {
+ .subdevs = mt9p031_camera_subdevs,
+ .interface = ISP_INTERFACE_PARALLEL,
+ .bus = {
+ .parallel = {
+ .data_lane_shift = 0,
+ .clk_pol = 1,
+ .bridge = ISPCTRL_PAR_BRIDGE_DISABLE,
+ }
+ },
+ },
+ { },
+};
+
+static struct isp_platform_data beagle_isp_platform_data = {
+ .subdevs = beagle_camera_subdevs,
+};
+
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -679,6 +796,11 @@ static void __init omap3_beagle_init(void)
beagle_display_init();
beagle_opp_init();
+
+ /* Enable camera */
+ gpio_request(MT9P031_RESET_GPIO, "cam_rst");
+ gpio_direction_output(MT9P031_RESET_GPIO, 0);
+ omap3_init_camera(&beagle_isp_platform_data);
}
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
@@ -200,7 +200,7 @@ static struct resource omap3isp_resources[] = {
}
};
-static struct platform_device omap3isp_device = {
+struct platform_device omap3isp_device = {
.name = "omap3isp",
.id = -1,
.num_resources = ARRAY_SIZE(omap3isp_resources),
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> --- arch/arm/mach-omap2/board-omap3beagle.c | 130 ++++++++++++++++++++++++++++++- arch/arm/mach-omap2/devices.c | 2 +- 2 files changed, 127 insertions(+), 5 deletions(-)