@@ -43,6 +43,7 @@
#include <linux/sh_intc.h>
#include <linux/tca6416_keypad.h>
#include <linux/usb/r8a66597.h>
+#include <linux/usb/renesas_usbhs.h>
#include <video/sh_mobile_hdmi.h>
#include <video/sh_mobile_lcdc.h>
@@ -143,7 +144,30 @@
* open | external VBUS | Function
*
* *1
- * CN31 is used as Host in Linux.
+ * CN31 is used as
+ * CONFIG_USB_R8A66597_HCD Host
+ * CONFIG_USB_RENESAS_USBHS Function
+ *
+ * CAUTION
+ *
+ * renesas_usbhs driver can use external interrupt mode
+ * (which come from USB-PHY) or autonomy mode (it use own interrupt)
+ * for detecting connection/disconnection when Function.
+ * USB will be power OFF while it has been disconnecting
+ * if external interrupt mode, and it is always power ON if autonomy mode,
+ *
+ * mackerel can not use external interrupt (IRQ7-PORT167) mode on "USB0",
+ * because Touchscreen is using IRQ7-PORT40.
+ * It is impossible to use IRQ7 demux on this board.
+ *
+ * We can use external interrupt mode USB-Function on "USB1".
+ * USB1 can become Host by r8a66597, and become Function by renesas_usbhs.
+ * But don't select both drivers in same time.
+ * These uses same IRQ number for request_irq(), and aren't supporting
+ * IRQF_SHARD / IORESOURCE_IRQ_SHAREABLE.
+ *
+ * Actually these are old/new version of USB driver.
+ * This mean its register will be broken if it supports SHARD IRQ,
*/
/*
@@ -185,6 +209,7 @@
* FIXME !!
*
* gpio_no_direction
+ * gpio_pull_down
* are quick_hack.
*
* current gpio frame work doesn't have
@@ -196,6 +221,16 @@ static void __init gpio_no_direction(u32 addr)
__raw_writeb(0x00, addr);
}
+static void __init gpio_pull_down(u32 addr)
+{
+ u8 data = __raw_readb(addr);
+
+ data &= 0x0F;
+ data |= 0xA0;
+
+ __raw_writeb(data, addr);
+}
+
/* MTD */
static struct mtd_partition nor_flash_partitions[] = {
{
@@ -509,6 +544,157 @@ static struct platform_device usb1_host_device = {
.resource = usb1_host_resources,
};
+/* USB1 (Function) */
+#define USB_PHY_MODE (1 << 4)
+#define USB_PHY_INT_EN ((1 << 3) | (1 << 2))
+#define USB_PHY_ON (1 << 1)
+#define USB_PHY_OFF (1 << 0)
+#define USB_PHY_INT_CLR (USB_PHY_ON | USB_PHY_OFF)
+
+struct usbhs_private {
+ unsigned int irq;
+ unsigned int usbphyaddr;
+ unsigned int usbcrcaddr;
+ struct renesas_usbhs_platform_info info;
+};
+
+#define usbhs_get_priv(pdev) \
+ container_of(renesas_usbhs_get_info(pdev), \
+ struct usbhs_private, info)
+
+#define usbhs_is_connected(priv) \
+ (!((1 << 7) & __raw_readw(priv->usbcrcaddr)))
+
+static int usbhs1_get_id(struct platform_device *pdev)
+{
+ return USBHS_GADGET;
+}
+
+static int usbhs1_get_vbus(struct platform_device *pdev)
+{
+ return usbhs_is_connected(usbhs_get_priv(pdev));
+}
+
+static irqreturn_t usbhs1_interrupt(int irq, void *data)
+{
+ struct platform_device *pdev = data;
+ struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+ dev_dbg(&pdev->dev, "%s\n", __func__);
+
+ renesas_usbhs_call_notify_hotplug(pdev);
+
+ /* clear status */
+ __raw_writew(__raw_readw(priv->usbphyaddr) | USB_PHY_INT_CLR,
+ priv->usbphyaddr);
+
+ return IRQ_HANDLED;
+}
+
+static int usbhs1_hardware_init(struct platform_device *pdev)
+{
+ struct usbhs_private *priv = usbhs_get_priv(pdev);
+ int ret;
+
+ irq_set_irq_type(priv->irq, IRQ_TYPE_LEVEL_HIGH);
+
+ /* clear interrupt status */
+ __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->usbphyaddr);
+
+ ret = request_irq(priv->irq, usbhs1_interrupt, 0,
+ dev_name(&pdev->dev), pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "request_irq err\n");
+ return ret;
+ }
+
+ /* enable USB phy interrupt */
+ __raw_writew(USB_PHY_MODE | USB_PHY_INT_EN, priv->usbphyaddr);
+
+ return 0;
+}
+
+static void usbhs1_hardware_exit(struct platform_device *pdev)
+{
+ struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+ /* clear interrupt status */
+ __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->usbphyaddr);
+
+ free_irq(priv->irq, pdev);
+}
+
+static void usbhs1_phy_reset(struct platform_device *pdev)
+{
+ struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+ /* init phy */
+ __raw_writew(0x8a0a, priv->usbcrcaddr);
+}
+
+static u32 usbhs1_pipe_cfg[] = {
+ USB_ENDPOINT_XFER_CONTROL,
+ USB_ENDPOINT_XFER_ISOC,
+ USB_ENDPOINT_XFER_ISOC,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_INT,
+ USB_ENDPOINT_XFER_INT,
+ USB_ENDPOINT_XFER_INT,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+ USB_ENDPOINT_XFER_BULK,
+};
+
+static struct usbhs_private usbhs1_private = {
+ .irq = evt2irq(0x0300), /* IRQ8 */
+ .usbphyaddr = 0xE60581E2, /* USBPHY1INTAP */
+ .usbcrcaddr = 0xE6058130, /* USBCR4 */
+ .info = {
+ .platform_callback = {
+ .hardware_init = usbhs1_hardware_init,
+ .hardware_exit = usbhs1_hardware_exit,
+ .phy_reset = usbhs1_phy_reset,
+ .get_id = usbhs1_get_id,
+ .get_vbus = usbhs1_get_vbus,
+ },
+ .driver_param = {
+ .buswait_bwait = 4,
+ .pipe_type = usbhs1_pipe_cfg,
+ .pipe_size = ARRAY_SIZE(usbhs1_pipe_cfg),
+ },
+ },
+};
+
+static struct resource usbhs1_resources[] = {
+ [0] = {
+ .name = "USBHS",
+ .start = 0xE68B0000,
+ .end = 0xE68B00E6 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = evt2irq(0x1ce0) /* USB1_USB1I0 */,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device usbhs1_device = {
+ .name = "renesas_usbhs",
+ .id = 1,
+ .dev = {
+ .platform_data = &usbhs1_private.info,
+ },
+ .num_resources = ARRAY_SIZE(usbhs1_resources),
+ .resource = usbhs1_resources,
+};
+
+
/* LED */
static struct gpio_led mackerel_leds[] = {
{
@@ -949,6 +1135,7 @@ static struct platform_device *mackerel_devices[] __initdata = {
&smc911x_device,
&lcdc_device,
&usb1_host_device,
+ &usbhs1_device,
&leds_device,
&fsi_device,
&fsi_ak4643_device,
@@ -1044,6 +1231,7 @@ static void __init mackerel_map_io(void)
#define GPIO_PORT9CR 0xE6051009
#define GPIO_PORT10CR 0xE605100A
+#define GPIO_PORT168CR 0xE60520A8
#define SRCR4 0xe61580bc
#define USCCR1 0xE6058144
static void __init mackerel_init(void)
@@ -1102,6 +1290,7 @@ static void __init mackerel_init(void)
gpio_request(GPIO_FN_OVCN_1_114, NULL);
gpio_request(GPIO_FN_EXTLP_1, NULL);
gpio_request(GPIO_FN_OVCN2_1, NULL);
+ gpio_pull_down(GPIO_PORT168CR);
/* setup USB phy */
__raw_writew(0x8a0a, 0xE6058130); /* USBCR4 */
renesas_usbhs driver can use external interrupt mode (which come from USB-PHY) or autonomy mode (it use own interrupt) for detecting connection/disconnection when Function. And it will be power OFF while it has been disconnecting if external interrupt mode is selected. mackerel board has 2 USB ports. But we can not use external interrupt mode on CN22 USB0 port which is only for USB Function. IRQ7-PORT40 is already used by Touchscreen, and USB-PHY needs IRQ7-PORT167. It is impossible to use IRQ7 demux on mackerel. We can use external interrupt mode USB-Function on "USB1". USB1 can become Host by r8a66597, and become Function by renesas_usbhs. But don't select both drivers in same time. These 2 drivers are not supporting IRQ SHARD. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> --- v1 -> v2 - modify documente for git - add documente to comment out - remove #ifdef/#error arch/arm/mach-shmobile/board-mackerel.c | 191 ++++++++++++++++++++++++++++++- 1 files changed, 190 insertions(+), 1 deletions(-)