@@ -9751,6 +9751,13 @@ S: Maintained
F: include/linux/mmc/dw_mmc.h
F: drivers/mmc/host/dw_mmc*
+SYNOPSYS SDHCI COMPLIANT DWC MSHC DRIVER
+M: Prabu Thangamuthu <prabu.t@synopsys.com>
+M: Manjunath M B <manjumb@synopsys.com>
+L: linux-mmc@vger.kernel.org
+S: Maintained
+F: drivers/mmc/host/sdhci-dwc-mshc*
+
SYSTEM TRACE MODULE CLASS
M: Alexander Shishkin <alexander.shishkin@linux.intel.com>
S: Maintained
@@ -9,7 +9,8 @@ obj-$(CONFIG_MMC_MXC) += mxcmmc.o
obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
-sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o
+sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o \
+ sdhci-dwc-mshc-pci.o
obj-$(subst m,y,$(CONFIG_MMC_SDHCI_PCI)) += sdhci-pci-data.o
obj-$(CONFIG_MMC_SDHCI_ACPI) += sdhci-acpi.o
obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
new file mode 100644
@@ -0,0 +1,298 @@
+/*
+ * Copyright (C) 2016 Synopsys, Inc.
+ *
+ * Author: Manjunath M B <manjumb@synopsys.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+
+#include "sdhci.h"
+#include "sdhci-pci.h"
+#include "sdhci-dwc-mshc-pci.h"
+
+/*****************************************************************************\
+ * *
+ * Hardware specific clock handling *
+ * *
+\*****************************************************************************/
+static const struct sdhci_ops *sdhci_ops; /* Low level hw interface */
+
+static void sdhci_set_clock_snps(struct sdhci_host *host,
+ unsigned int clock)
+{
+ int div = 0;
+ int mul = 0;
+ int div_val = 0;
+ int mul_val = 0;
+ int mul_div_val = 0;
+ int reg = 0;
+ u16 clk = 0;
+ u32 vendor_ptr;
+ unsigned long timeout;
+ u32 tx_clk_phase_val = SDHC_DEF_TX_CLK_PH_VAL;
+ u32 rx_clk_phase_val = SDHC_DEF_RX_CLK_PH_VAL;
+
+ /* DWC MSHC Specific clock settings */
+
+ /* if clock is less than 25MHz, divided clock is used.
+ * For divided clock, we can use the standard sdhci_set_clock().
+ * For clock above 25MHz, DRP clock is used
+ * Here, we cannot use sdhci_set_clock(), we need to program
+ * TX RX CLOCK DCM DRP for appropriate clock
+ */
+
+ vendor_ptr = sdhci_readw(host, SDHCI_UHS2_VENDOR);
+
+ if (clock <= 25000000) {
+ /* Then call generic set_clock */
+ sdhci_ops->set_clock(host, clock);
+ } else {
+
+ host->mmc->actual_clock = 0;
+
+ /* Select un-phase shifted clock before reset Tx Tuning DCM*/
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg &= ~SDHC_TX_CLK_SEL_TUNED;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ mdelay(10);
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ /* Lets chose the Mulitplier value to be 0x2 */
+ mul = 0x2;
+ for (div = 1; div <= 32; div++) {
+ if (((host->max_clk * mul) / div)
+ <= clock)
+ break;
+ }
+ /*
+ * Set Programmable Clock Mode in the Clock
+ * Control register.
+ */
+ div_val = div - 1;
+ mul_val = mul - 1;
+
+ host->mmc->actual_clock = (host->max_clk * mul) / div;
+ /* Program the DCM DRP */
+ /* Step 1: Assert DCM Reset */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | SDHC_CARD_TX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+
+ /* Step 2: Program the mul and div values in DRP */
+ mul_div_val = (mul_val << 8) | div_val;
+ sdhci_writew(host, mul_div_val, TXRX_CLK_DCM_MUL_DIV_DRP);
+
+ /* Step 3: issue a dummy read from DRP base 0x00 as per
+ * www.xilinx.com/support/documentation/user_guides/ug191.pdf
+ */
+ reg = sdhci_readw(host, TXRX_CLK_DCM_DRP_BASE_51);
+
+ /* Step 4: De-Assert reset to DCM */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg &= ~SDHC_CARD_TX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+
+ clk |= SDHCI_PROG_CLOCK_MODE | SDHCI_CLOCK_INT_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ /* Wait max 20 ms */
+ timeout = 20;
+ while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
+ & SDHCI_CLOCK_INT_STABLE)) {
+ if (timeout == 0) {
+ pr_err("%s: Internal clock never stabilised\n",
+ mmc_hostname(host->mmc));
+ return;
+ }
+ timeout--;
+ mdelay(1);
+ }
+
+ clk |= SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ /* For some bit-files we may have to do phase shifting for
+ * Tx Clock; Let's do it here
+ */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | SDHC_TUNING_TX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ mdelay(10);
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg &= ~SDHC_TUNING_TX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+
+ /* Select working phase value if clock is <= 50MHz */
+ if (clock <= 50000000) {
+ /*Change the Phase value here */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | (SDHC_TUNING_TX_CLK_SEL_MASK &
+ (tx_clk_phase_val << SDHC_TUNING_TX_CLK_SEL_SHIFT));
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ mdelay(10);
+
+ /* Program to select phase shifted clock */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | SDHC_TX_CLK_SEL_TUNED;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ mdelay(10);
+ }
+
+ /* This Clock might have affected the RX CLOCK DCM
+ * used for Phase control; Reset this DCM for proper clock
+ */
+
+ /* Program the DCM DRP */
+ /* Step 1: Reset the DCM */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | SDHC_TUNING_RX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ mdelay(10);
+ /* Step 2: De-Assert reset to DCM */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg &= ~SDHC_TUNING_RX_CLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+
+ /* For 50Mhz, tuning is not possible.. Lets fix the sampling
+ * Phase of Rx Clock here
+ */
+ if (clock <= 50000000) {
+ /*Change the Phase value here */
+ reg = sdhci_readl(host, (SDHC_DBOUNCE + vendor_ptr));
+ reg &= ~SDHC_TUNING_RX_CLK_SEL_MASK;
+ reg = reg | (SDHC_TUNING_RX_CLK_SEL_MASK &
+ rx_clk_phase_val);
+ sdhci_writew(host, reg, (SDHC_DBOUNCE + vendor_ptr));
+ }
+ mdelay(10);
+ }
+}
+
+static int sdhci_pci_enable_dma_snps(struct sdhci_host *host)
+{
+ /* DWC MSHC Specific Dma Enabling */
+
+ /* Call generic emable_dma */
+ return sdhci_ops->enable_dma(host);
+}
+
+static void sdhci_pci_set_bus_width_snps(struct sdhci_host *host, int width)
+{
+ /* DWC MSHC Specific Bus Width Setting */
+
+ /* Call generic set_bus_width */
+ sdhci_ops->set_bus_width(host, width);
+}
+
+static void sdhci_reset_snps(struct sdhci_host *host, u8 mask)
+{
+ /* DWC MSHC Specific hci reset */
+
+ /* Call generic reset */
+ sdhci_ops->reset(host, mask);
+}
+static void sdhci_set_uhs_signaling_snps(struct sdhci_host *host,
+ unsigned int timing)
+{
+ /* DWC MSHC Specific UHS-I Signaling */
+
+ /* Call generic UHS-I signaling */
+ sdhci_ops->set_uhs_signaling(host, timing);
+}
+static void sdhci_pci_hw_reset_snps(struct sdhci_host *host)
+{
+ /* DWC MSHC Specific hw reset */
+
+ /* Call generic hw_reset */
+ if (host->ops && host->ops->hw_reset)
+ sdhci_ops->hw_reset(host);
+}
+static const struct sdhci_ops sdhci_pci_ops_snps = {
+ .set_clock = sdhci_set_clock_snps,
+ .enable_dma = sdhci_pci_enable_dma_snps,
+ .set_bus_width = sdhci_pci_set_bus_width_snps,
+ .reset = sdhci_reset_snps,
+ .set_uhs_signaling = sdhci_set_uhs_signaling_snps,
+ .hw_reset = sdhci_pci_hw_reset_snps,
+};
+
+static int snps_init_clock(struct sdhci_host *host)
+{
+ int div = 0;
+ int mul = 0;
+ int div_val = 0;
+ int mul_val = 0;
+ int mul_div_val = 0;
+ int reg = 0;
+ u32 vendor_ptr;
+
+ vendor_ptr = sdhci_readw(host, SDHCI_UHS2_VENDOR);
+
+ /* Configure the BCLK DRP to get 100 MHZ Clock */
+
+ /* To get 100MHz from 100MHz input freq,
+ * mul=2 and div=2
+ * Formula: output_clock = (input clock * mul) / div
+ */
+ mul = 2;
+ div = 2;
+ mul_val = mul - 1;
+ div_val = div - 1;
+ /* Program the DCM DRP */
+ /* Step 1: Reset the DCM */
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg = reg | SDHC_BCLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+ /* Step 2: Program the mul and div values in DRP */
+ mul_div_val = (mul_val << 8) | div_val;
+ sdhci_writew(host, mul_div_val, BCLK_DCM_MUL_DIV_DRP);
+ /* Step 3: issue a dummy read from DRP base 0x00 as per
+ * http://www.xilinx.com/support/documentation/user_guides/ug191.pdf
+ */
+ reg = sdhci_readw(host, BCLK_DCM_DRP_BASE_51);
+ /* Step 4: De-Assert reset to DCM */
+ /* de assert reset*/
+ reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
+ reg &= ~SDHC_BCLK_DCM_RST;
+ sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
+
+ /* By Default Clocks to MSHC are off..
+ * Before stack applies reset; we need to turn on the clock
+ */
+ sdhci_writew(host, SDHCI_CLOCK_INT_EN, SDHCI_CLOCK_CONTROL);
+
+ return 0;
+
+}
+
+int sdhci_pci_probe_slot_snps(struct sdhci_pci_slot *slot)
+{
+ int ret = 0;
+ struct sdhci_host *host;
+
+ host = slot->host;
+ sdhci_ops = host->ops;
+ host->ops = &sdhci_pci_ops_snps;
+
+ /* Board specific clock initialization */
+ ret = snps_init_clock(host);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(sdhci_pci_probe_slot_snps);
new file mode 100644
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2016 Synopsys, Inc.
+ *
+ * Author: Manjunath M B <manjumb@synopsys.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __SDHCI_DWC_MSHC_PCI_H__
+#define __SDHCI_DWC_MSHC_PCI_H__
+
+#include "sdhci-pci.h"
+
+#define SDHCI_UHS2_VENDOR 0xE8
+
+#define DRIVER_NAME "sdhci_snps"
+#define SDHC_DEF_TX_CLK_PH_VAL 4
+#define SDHC_DEF_RX_CLK_PH_VAL 4
+
+/* Synopsys Vendor Specific Registers */
+#define SDHC_DBOUNCE 0x08
+#define SDHC_TUNING_RX_CLK_SEL_MASK 0x000000FF
+#define SDHC_GPIO_OUT 0x34
+/* HAPS 51 Based implementation */
+#define SDHC_BCLK_DCM_RST 0x00000001
+#define SDHC_CARD_TX_CLK_DCM_RST 0x00000002
+#define SDHC_TUNING_RX_CLK_DCM_RST 0x00000004
+#define SDHC_TUNING_TX_CLK_DCM_RST 0x00000008
+#define SDHC_TUNING_TX_CLK_SEL_MASK 0x00000070
+#define SDHC_TUNING_TX_CLK_SEL_SHIFT 4
+#define SDHC_TX_CLK_SEL_TUNED 0x00000080
+
+/* Offset of BCLK DCM DRP Attributes */
+/* Every attribute is of 16 bit wide */
+#define BCLK_DCM_DRP_BASE_51 0x1000
+
+#define BCLK_DCM_MUL_DIV_DRP 0x1050
+#define MUL_MASK_DRP 0xFF00
+#define DIV_MASK_DRP 0x00FF
+
+/* Offset of TX and RX CLK DCM DRP */
+#define TXRX_CLK_DCM_DRP_BASE_51 0x2000
+#define TXRX_CLK_DCM_MUL_DIV_DRP 0x2050
+
+int sdhci_pci_probe_snps(struct sdhci_pci_chip *chip);
+int sdhci_pci_probe_slot_snps(struct sdhci_pci_slot *slot);
+int sdhci_pci_resume_snps(struct sdhci_pci_chip *chip);
+int sdhci_pci_suspend_snps(struct sdhci_pci_chip *chip);
+
+#endif
@@ -31,6 +31,7 @@
#include "sdhci.h"
#include "sdhci-pci.h"
#include "sdhci-pci-o2micro.h"
+#include "sdhci-dwc-mshc-pci.h"
/*****************************************************************************\
* *
@@ -70,6 +71,11 @@ static int ricoh_mmc_resume(struct sdhci_pci_chip *chip)
msleep(500);
return 0;
}
+/* Synopsys DWC MSHC Controller based SDHCI-PCI */
+static const struct sdhci_pci_fixes sdhci_snps = {
+ .probe_slot = sdhci_pci_probe_slot_snps,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
+};
static const struct sdhci_pci_fixes sdhci_ricoh = {
.probe = ricoh_probe,
@@ -797,6 +803,14 @@ static const struct sdhci_pci_fixes sdhci_amd = {
static const struct pci_device_id pci_ids[] = {
{
+ .vendor = PCI_VENDOR_ID_SYNOPSYS,
+ .device = PCI_DEVICE_ID_MSHC_HAPS51,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = (kernel_ulong_t)&sdhci_snps,
+ },
+
+ {
.vendor = PCI_VENDOR_ID_RICOH,
.device = PCI_DEVICE_ID_RICOH_R5C822,
.subvendor = PCI_ANY_ID,
@@ -2318,6 +2318,9 @@
#define PCI_DEVICE_ID_CENATEK_IDE 0x0001
#define PCI_VENDOR_ID_SYNOPSYS 0x16c3
+#define PCI_DEVICE_ID_MOBSTOR_HAPS51 0xc101
+#define PCI_DEVICE_ID_MSHC_HAPS51 0xc201
+#define PCI_DEVICE_ID_MSHC_HAPSDX 0xc202
#define PCI_VENDOR_ID_VITESSE 0x1725
#define PCI_DEVICE_ID_VITESSE_VSC7174 0x7174
Synopsys released SD Host Controller Standard Specification compliant IP called as DWC_MSHC. This patch is to support DWC_MSHC controller with PCI interface. Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com> --- MAINTAINERS | 7 + drivers/mmc/host/Makefile | 3 +- drivers/mmc/host/sdhci-dwc-mshc-pci.c | 298 ++++++++++++++++++++++++++++++++++ drivers/mmc/host/sdhci-dwc-mshc-pci.h | 58 +++++++ drivers/mmc/host/sdhci-pci-core.c | 14 ++ include/linux/pci_ids.h | 3 + 6 files changed, 382 insertions(+), 1 deletion(-) create mode 100644 drivers/mmc/host/sdhci-dwc-mshc-pci.c create mode 100644 drivers/mmc/host/sdhci-dwc-mshc-pci.h