@@ -95,7 +95,8 @@ dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
bcm958305k.dtb
dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
bcm28155-ap.dtb \
- bcm21664-garnet.dtb
+ bcm21664-garnet.dtb \
+ bcm23550-sparrow.dtb
dtb-$(CONFIG_ARCH_BCM_NSP) += \
bcm958625k.dtb
dtb-$(CONFIG_ARCH_BERLIN) += \
new file mode 100644
@@ -0,0 +1,75 @@
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm23550.dtsi"
+
+/ {
+ model = "BCM23550 Sparrow board";
+ compatible = "brcm,bcm23550-sparrow", "brcm,bcm23550";
+
+ memory {
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+};
+
+&uartb {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&sdio1 {
+ max-frequency = <48000000>;
+ status = "okay";
+};
+
+&sdio2 {
+ non-removable;
+ max-frequency = <48000000>;
+ status = "okay";
+};
+
+&sdio4 {
+ max-frequency = <48000000>;
+ cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,419 @@
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/* BCM23550 and BCM21664 have almost identical clocks */
+#include "dt-bindings/clock/bcm21664.h"
+
+#include "skeleton.dtsi"
+
+/ {
+ model = "BCM23550 SoC";
+ compatible = "brcm,bcm23550";
+ interrupt-parent = <&gic>;
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550-cpu-method";
+ secondary-boot-reg = <0x35004178>;
+ reg = <1>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550-cpu-method";
+ secondary-boot-reg = <0x35004178>;
+ reg = <2>;
+ clock-frequency = <1000000000>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ enable-method = "brcm,bcm23550-cpu-method";
+ secondary-boot-reg = <0x35004178>;
+ reg = <3>;
+ clock-frequency = <1000000000>;
+ };
+ };
+
+ /* Hub bus */
+ hub@34000000 {
+ compatible = "simple-bus";
+ ranges = <0 0x34000000 0x102f83ac>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ smc@4e000 {
+ compatible = "brcm,bcm23550-smc", "brcm,kona-smc";
+ reg = <0x0004e000 0x400>; /* 1 KiB in SRAM */
+ };
+
+ resetmgr: reset-controller@1001f00 {
+ compatible = "brcm,bcm21664-resetmgr";
+ reg = <0x01001f00 0x24>;
+ };
+
+ gpio: gpio@1003000 {
+ compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
+ reg = <0x01003000 0x524>;
+ interrupts =
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+
+ timer@1006000 {
+ compatible = "brcm,kona-timer";
+ reg = <0x01006000 0x1c>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&aon_ccu BCM21664_AON_CCU_HUB_TIMER>;
+ };
+ };
+
+ /* Slaves bus */
+ slaves@3e000000 {
+ compatible = "simple-bus";
+ ranges = <0 0x3e000000 0x0001c070>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uartb: serial@0 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00000000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ uartb2: serial@1000 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00001000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ uartb3: serial@2000 {
+ compatible = "snps,dw-apb-uart";
+ status = "disabled";
+ reg = <0x00002000 0x118>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ bsc1: i2c@16000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00016000 0x70>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC1>;
+ status = "disabled";
+ };
+
+ bsc2: i2c@17000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00017000 0x70>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC2>;
+ status = "disabled";
+ };
+
+ bsc3: i2c@18000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x00018000 0x70>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC3>;
+ status = "disabled";
+ };
+
+ bsc4: i2c@1c000 {
+ compatible = "brcm,kona-i2c";
+ reg = <0x0001c000 0x70>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC4>;
+ status = "disabled";
+ };
+ };
+
+ /* Apps bus */
+ apps@3e300000 {
+ compatible = "simple-bus";
+ ranges = <0 0x3e300000 0x01b77000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usbotg: usb@e20000 {
+ compatible = "snps,dwc2";
+ reg = <0x00e20000 0x10000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_otg_ahb_clk>;
+ clock-names = "otg";
+ phys = <&usbphy>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ usbphy: usb-phy@e30000 {
+ compatible = "brcm,kona-usb2-phy";
+ reg = <0x00e30000 0x28>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ sdio1: sdio@e80000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00e80000 0x801c>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO1>;
+ status = "disabled";
+ };
+
+ sdio2: sdio@e90000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00e90000 0x801c>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO2>;
+ status = "disabled";
+ };
+
+ sdio3: sdio@ea0000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00ea0000 0x801c>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO3>;
+ status = "disabled";
+ };
+
+ sdio4: sdio@eb0000 {
+ compatible = "brcm,kona-sdhci";
+ reg = <0x00eb0000 0x801c>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
+ status = "disabled";
+ };
+
+ cdc: cdc@1b0e000 {
+ compatible = "brcm,bcm23550-cdc";
+ reg = <0x01b0e000 0x78>;
+ };
+
+ gic: interrupt-controller@1b21000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x01b21000 0x1000>,
+ <0x01b22000 0x1000>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /*
+ * Fixed clocks are defined before CCUs whose
+ * clocks may depend on them.
+ */
+
+ ref_32k_clk: ref_32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ bbl_32k_clk: bbl_32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ ref_13m_clk: ref_13m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ };
+
+ var_13m_clk: var_13m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ };
+
+ dft_19_5m_clk: dft_19_5m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <19500000>;
+ };
+
+ ref_crystal_clk: ref_crystal {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ };
+
+ ref_52m_clk: ref_52m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ var_52m_clk: var_52m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ usb_otg_ahb_clk: usb_otg_ahb {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <52000000>;
+ };
+
+ ref_96m_clk: ref_96m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <96000000>;
+ };
+
+ var_96m_clk: var_96m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <96000000>;
+ };
+
+ ref_104m_clk: ref_104m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <104000000>;
+ };
+
+ var_104m_clk: var_104m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <104000000>;
+ };
+
+ ref_156m_clk: ref_156m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <156000000>;
+ };
+
+ var_156m_clk: var_156m {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <156000000>;
+ };
+
+ root_ccu: root_ccu {
+ compatible = BCM21664_DT_ROOT_CCU_COMPAT;
+ reg = <0x35001000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "frac_1m";
+ };
+
+ aon_ccu: aon_ccu {
+ compatible = BCM21664_DT_AON_CCU_COMPAT;
+ reg = <0x35002000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "hub_timer";
+ };
+
+ slave_ccu: slave_ccu {
+ compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
+ reg = <0x3e011000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "uartb",
+ "uartb2",
+ "uartb3",
+ "bsc1",
+ "bsc2",
+ "bsc3",
+ "bsc4";
+ };
+
+ master_ccu: master_ccu {
+ compatible = BCM21664_DT_MASTER_CCU_COMPAT;
+ reg = <0x3f001000 0x0f00>;
+ #clock-cells = <1>;
+ clock-output-names = "sdio1",
+ "sdio2",
+ "sdio3",
+ "sdio4",
+ "sdio1_sleep",
+ "sdio2_sleep",
+ "sdio3_sleep",
+ "sdio4_sleep";
+ };
+ };
+};
Add device tree files for the Broadcom BCM23550 SoC and the Broadcom Sparrow board. Signed-off-by: Chris Brand <chris.brand@broadcom.com> --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/bcm23550-sparrow.dts | 75 ++++++ arch/arm/boot/dts/bcm23550.dtsi | 419 +++++++++++++++++++++++++++++++++ 3 files changed, 496 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/bcm23550-sparrow.dts create mode 100644 arch/arm/boot/dts/bcm23550.dtsi