| Message ID | 1462957929-20105-2-git-send-email-henryc.chen@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Henry, On Wed, May 11, 2016 at 5:12 PM, Henry Chen <henryc.chen@mediatek.com> wrote: > > Some regulators support their operating mode to be changed by > consumers for module specific purpose. > > This patch adds support to parse those properties and fill the > regulator constraints so the regulator core can call the > regualtor_set_mode to change the modes. > > Signed-off-by: Henry Chen <henryc.chen@mediatek.com> > --- > Documentation/devicetree/bindings/regulator/regulator.txt | 10 ++++++++++ > drivers/regulator/of_regulator.c | 14 ++++++++++++++ > 2 files changed, 24 insertions(+) > > diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt > index ecfc593..88f98f0 100644 > --- a/Documentation/devicetree/bindings/regulator/regulator.txt > +++ b/Documentation/devicetree/bindings/regulator/regulator.txt > @@ -49,6 +49,16 @@ Optional properties: > 0: Disable active discharge. > 1: Enable active discharge. > Absence of this property will leave configuration to default. > +- regulator-allow-change-mode: allow the regulator mode to be configured As mentioned by broonie earlier, the explicit 'allow' property is redundant, if regulator-supported-modes is present, then set REGULATOR_CHANGE_MODE invalid_ops_mask , else leave it clear. > +- regulator-supported-modes: Regulators can run in a variety of different operating > + modes depending on output load. This allows further system power savings by > + selecting the best (and most efficient) regulator mode for a desired load. > + The definition for each of these operation is defined at > + include/linux/regulator/consumer.h > + 0: FAST. > + 1: NORMAL. > + 2: IDLE. > + 3: STANDBY. > > Deprecated properties: > - regulator-compatible: If a regulator chip contains multiple > diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c > index 6b0aa80..12fe8c8 100644 > --- a/drivers/regulator/of_regulator.c > +++ b/drivers/regulator/of_regulator.c Also, I thought binding document changes are generally in a separate patch from their implementation. -Dan > @@ -167,6 +167,20 @@ static void of_get_regulation_constraints(struct device_node *np, > suspend_state = NULL; > suspend_np = NULL; > } > + > + if (of_property_read_bool(np, "regulator-allow-change-mode")) > + constraints->valid_ops_mask |= REGULATOR_CHANGE_MODE; > + > + ret = of_property_count_elems_of_size(np, > + "regulator-supported-modes", > + sizeof(u32)); > + for (i = 0; i < ret; i++) { > + u32 mode; > + > + of_property_read_u32_index(np, "regulator-supported-modes", > + i, &mode); > + constraints->valid_modes_mask |= (1 << mode); > + } > } > > /** > -- > 1.8.1.1.dirty >
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc593..88f98f0 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -49,6 +49,16 @@ Optional properties: 0: Disable active discharge. 1: Enable active discharge. Absence of this property will leave configuration to default. +- regulator-allow-change-mode: allow the regulator mode to be configured +- regulator-supported-modes: Regulators can run in a variety of different operating + modes depending on output load. This allows further system power savings by + selecting the best (and most efficient) regulator mode for a desired load. + The definition for each of these operation is defined at + include/linux/regulator/consumer.h + 0: FAST. + 1: NORMAL. + 2: IDLE. + 3: STANDBY. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index 6b0aa80..12fe8c8 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -167,6 +167,20 @@ static void of_get_regulation_constraints(struct device_node *np, suspend_state = NULL; suspend_np = NULL; } + + if (of_property_read_bool(np, "regulator-allow-change-mode")) + constraints->valid_ops_mask |= REGULATOR_CHANGE_MODE; + + ret = of_property_count_elems_of_size(np, + "regulator-supported-modes", + sizeof(u32)); + for (i = 0; i < ret; i++) { + u32 mode; + + of_property_read_u32_index(np, "regulator-supported-modes", + i, &mode); + constraints->valid_modes_mask |= (1 << mode); + } } /**
Some regulators support their operating mode to be changed by consumers for module specific purpose. This patch adds support to parse those properties and fill the regulator constraints so the regulator core can call the regualtor_set_mode to change the modes. Signed-off-by: Henry Chen <henryc.chen@mediatek.com> --- Documentation/devicetree/bindings/regulator/regulator.txt | 10 ++++++++++ drivers/regulator/of_regulator.c | 14 ++++++++++++++ 2 files changed, 24 insertions(+)