| Message ID | 20160608010429.19618-3-stefan@agner.ch (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Jun 07, 2016 at 06:04:26PM -0700, Stefan Agner wrote: > The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is, > the differences are: > > + DCDC4 > + Slightly different output voltage/currents > + 32kHz Output > - ADC/Charger capabilities > > Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> > Signed-off-by: Stefan Agner <stefan@agner.ch> > --- > Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++------- > drivers/mfd/Kconfig | 7 +++--- > drivers/mfd/rn5t618.c | 26 +++++++++++++++++------ > include/linux/mfd/rn5t618.h | 12 +++++++++++ > 4 files changed, 46 insertions(+), 18 deletions(-) > > diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt > index 937785a..5b493ed 100644 > --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt > +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt > @@ -1,18 +1,21 @@ > -* Ricoh RN5T618 PMIC > +* Ricoh RN5T567/RN5T618 PMIC > > -Ricoh RN5T618 is a power management IC which integrates 3 step-down > -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, > -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled > -through a I2C interface. > +Ricoh RN5T567/RN5T618 is a power management IC family which integrates > +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and I count 4? Otherwise, for the binding: Acked-by: Rob Herring <robh@kernel.org>
On 2016-06-08 13:22, Rob Herring wrote: > On Tue, Jun 07, 2016 at 06:04:26PM -0700, Stefan Agner wrote: >> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is, >> the differences are: >> >> + DCDC4 >> + Slightly different output voltage/currents >> + 32kHz Output >> - ADC/Charger capabilities >> >> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> >> Signed-off-by: Stefan Agner <stefan@agner.ch> >> --- >> Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++------- >> drivers/mfd/Kconfig | 7 +++--- >> drivers/mfd/rn5t618.c | 26 +++++++++++++++++------ >> include/linux/mfd/rn5t618.h | 12 +++++++++++ >> 4 files changed, 46 insertions(+), 18 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt >> index 937785a..5b493ed 100644 >> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt >> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt >> @@ -1,18 +1,21 @@ >> -* Ricoh RN5T618 PMIC >> +* Ricoh RN5T567/RN5T618 PMIC >> >> -Ricoh RN5T618 is a power management IC which integrates 3 step-down >> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, >> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled >> -through a I2C interface. >> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates >> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and > > I count 4? There is actually a third PMIC in this family RC5T619 which has 5, that is where the number comes from. But that PMIC also has 12 LDO's so the numbers are a bit a mix and much right now... If I have to amend something anyway, I will fix that. Otherwise I look at it as a preparation for the one which adds RC5T619 support :-) -- Stefan
On Tue, 07 Jun 2016, Stefan Agner wrote: > The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is, > the differences are: > > + DCDC4 > + Slightly different output voltage/currents > + 32kHz Output > - ADC/Charger capabilities > > Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> > Signed-off-by: Stefan Agner <stefan@agner.ch> > --- > Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++------- > drivers/mfd/Kconfig | 7 +++--- > drivers/mfd/rn5t618.c | 26 +++++++++++++++++------ > include/linux/mfd/rn5t618.h | 12 +++++++++++ > 4 files changed, 46 insertions(+), 18 deletions(-) > > diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt > index 937785a..5b493ed 100644 > --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt > +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt > @@ -1,18 +1,21 @@ > -* Ricoh RN5T618 PMIC > +* Ricoh RN5T567/RN5T618 PMIC > > -Ricoh RN5T618 is a power management IC which integrates 3 step-down > -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, > -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled > -through a I2C interface. > +Ricoh RN5T567/RN5T618 is a power management IC family which integrates > +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and > +a watchdog timer. The RN5T618 provides additionally a Li-ion battery > +charger, fuel gauge and an ADC. It can be controlled through a I2C Nit: s/a I2C/an I2C/ > +interface. > > Required properties: > - - compatible: should be "ricoh,rn5t618" > + - compatible: must be one of > + "ricoh,rn5t567" > + "ricoh,rn5t618" > - reg: the I2C slave address of the device > > Sub-nodes: > - regulators: the node is required if the regulator functionality is > - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, > - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. > + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 > + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. > The common bindings for each individual regulator can be found in: > Documentation/devicetree/bindings/regulator/regulator.txt > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 1bcf601..ff031a7 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -852,13 +852,14 @@ config MFD_RK808 > including interrupts, RTC, LDO & DCDC regulators, and onkey. > > config MFD_RN5T618 > - tristate "Ricoh RN5T5618 PMIC" > + tristate "Ricoh RN5T567/618 PMIC" > depends on I2C > + depends on OF > select MFD_CORE > select REGMAP_I2C > help > - Say yes here to add support for the Ricoh RN5T618 PMIC. This > - driver provides common support for accessing the device, > + Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC. > + This driver provides common support for accessing the device, > additional drivers must be enabled in order to use the > functionality of the device. > > diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c > index 0ad51d7..7607ced 100644 > --- a/drivers/mfd/rn5t618.c > +++ b/drivers/mfd/rn5t618.c > @@ -2,6 +2,7 @@ > * MFD core driver for Ricoh RN5T618 PMIC > * > * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> > + * Copyright (C) 2016 Toradex AG > * > * This program is free software; you can redistribute it and/or > * modify it under the terms of the GNU General Public License > @@ -15,6 +16,7 @@ > #include <linux/mfd/core.h> > #include <linux/mfd/rn5t618.h> > #include <linux/module.h> > +#include <linux/of_device.h> > #include <linux/regmap.h> > > static const struct mfd_cell rn5t618_cells[] = { > @@ -59,12 +61,26 @@ static void rn5t618_power_off(void) > RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF); > } > > +static const struct of_device_id rn5t618_of_match[] = { > + { .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 }, > + { .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, rn5t618_of_match); > + > static int rn5t618_i2c_probe(struct i2c_client *i2c, > const struct i2c_device_id *id) > { > + const struct of_device_id *of_id = > + of_match_device(rn5t618_of_match, &i2c->dev); I'd prefer you did the call *after* the variable declarations. > struct rn5t618 *priv; > int ret; So here -> > + if (!of_id) { > + dev_err(&i2c->dev, "Failed to find matching dt id\n"); s/dt id/DT ID/ > + return -EINVAL; > + } > + > priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL); > if (!priv) > return -ENOMEM; > @@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c, > return ret; > } > > + priv->variant = (long)of_id->data; > + Why here and not directly after the of_id check? > ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells, > ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL); > if (ret) { > @@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c) > return 0; > } > > -static const struct of_device_id rn5t618_of_match[] = { > - { .compatible = "ricoh,rn5t618" }, > - { } > -}; > -MODULE_DEVICE_TABLE(of, rn5t618_of_match); > - > static const struct i2c_device_id rn5t618_i2c_id[] = { > { } > }; > @@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = { > module_i2c_driver(rn5t618_i2c_driver); > > MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); > -MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver"); > +MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver"); > MODULE_LICENSE("GPL v2"); > diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h > index c72d534..54179c2 100644 > --- a/include/linux/mfd/rn5t618.h > +++ b/include/linux/mfd/rn5t618.h > @@ -20,6 +20,7 @@ > #define RN5T618_OTPVER 0x01 > #define RN5T618_IODAC 0x02 > #define RN5T618_VINDAC 0x03 > +#define RN5T618_OUT32KEN 0x05 > #define RN5T618_CPUCNT 0x06 > #define RN5T618_PSWR 0x07 > #define RN5T618_PONHIS 0x09 > @@ -38,6 +39,7 @@ > #define RN5T618_DC1_SLOT 0x16 > #define RN5T618_DC2_SLOT 0x17 > #define RN5T618_DC3_SLOT 0x18 > +#define RN5T618_DC4_SLOT 0x19 > #define RN5T618_LDO1_SLOT 0x1b > #define RN5T618_LDO2_SLOT 0x1c > #define RN5T618_LDO3_SLOT 0x1d > @@ -54,12 +56,16 @@ > #define RN5T618_DC2CTL2 0x2f > #define RN5T618_DC3CTL 0x30 > #define RN5T618_DC3CTL2 0x31 > +#define RN5T618_DC4CTL 0x32 > +#define RN5T618_DC4CTL2 0x33 > #define RN5T618_DC1DAC 0x36 > #define RN5T618_DC2DAC 0x37 > #define RN5T618_DC3DAC 0x38 > +#define RN5T618_DC4DAC 0x39 > #define RN5T618_DC1DAC_SLP 0x3b > #define RN5T618_DC2DAC_SLP 0x3c > #define RN5T618_DC3DAC_SLP 0x3d > +#define RN5T618_DC4DAC_SLP 0x3e > #define RN5T618_DCIREN 0x40 > #define RN5T618_DCIRQ 0x41 > #define RN5T618_DCIRMON 0x42 > @@ -221,8 +227,14 @@ enum { > RN5T618_REG_NUM, > }; > > +enum { > + RN5T567 = 0, > + RN5T618, > +}; > + > struct rn5t618 { > struct regmap *regmap; > + long variant; What do you use this for? > }; > > #endif /* __LINUX_MFD_RN5T618_H */
On 2016-06-16 07:55, Lee Jones wrote: > On Tue, 07 Jun 2016, Stefan Agner wrote: > >> The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is, >> the differences are: >> >> + DCDC4 >> + Slightly different output voltage/currents >> + 32kHz Output >> - ADC/Charger capabilities >> >> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> >> Signed-off-by: Stefan Agner <stefan@agner.ch> >> --- >> Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++------- >> drivers/mfd/Kconfig | 7 +++--- >> drivers/mfd/rn5t618.c | 26 +++++++++++++++++------ >> include/linux/mfd/rn5t618.h | 12 +++++++++++ >> 4 files changed, 46 insertions(+), 18 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt >> index 937785a..5b493ed 100644 >> --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt >> +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt >> @@ -1,18 +1,21 @@ >> -* Ricoh RN5T618 PMIC >> +* Ricoh RN5T567/RN5T618 PMIC >> >> -Ricoh RN5T618 is a power management IC which integrates 3 step-down >> -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, >> -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled >> -through a I2C interface. >> +Ricoh RN5T567/RN5T618 is a power management IC family which integrates >> +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and >> +a watchdog timer. The RN5T618 provides additionally a Li-ion battery >> +charger, fuel gauge and an ADC. It can be controlled through a I2C > > Nit: s/a I2C/an I2C/ > >> +interface. >> >> Required properties: >> - - compatible: should be "ricoh,rn5t618" >> + - compatible: must be one of >> + "ricoh,rn5t567" >> + "ricoh,rn5t618" >> - reg: the I2C slave address of the device >> >> Sub-nodes: >> - regulators: the node is required if the regulator functionality is >> - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, >> - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. >> + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 >> + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. >> The common bindings for each individual regulator can be found in: >> Documentation/devicetree/bindings/regulator/regulator.txt >> >> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig >> index 1bcf601..ff031a7 100644 >> --- a/drivers/mfd/Kconfig >> +++ b/drivers/mfd/Kconfig >> @@ -852,13 +852,14 @@ config MFD_RK808 >> including interrupts, RTC, LDO & DCDC regulators, and onkey. >> >> config MFD_RN5T618 >> - tristate "Ricoh RN5T5618 PMIC" >> + tristate "Ricoh RN5T567/618 PMIC" >> depends on I2C >> + depends on OF >> select MFD_CORE >> select REGMAP_I2C >> help >> - Say yes here to add support for the Ricoh RN5T618 PMIC. This >> - driver provides common support for accessing the device, >> + Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC. >> + This driver provides common support for accessing the device, >> additional drivers must be enabled in order to use the >> functionality of the device. >> >> diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c >> index 0ad51d7..7607ced 100644 >> --- a/drivers/mfd/rn5t618.c >> +++ b/drivers/mfd/rn5t618.c >> @@ -2,6 +2,7 @@ >> * MFD core driver for Ricoh RN5T618 PMIC >> * >> * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> >> + * Copyright (C) 2016 Toradex AG >> * >> * This program is free software; you can redistribute it and/or >> * modify it under the terms of the GNU General Public License >> @@ -15,6 +16,7 @@ >> #include <linux/mfd/core.h> >> #include <linux/mfd/rn5t618.h> >> #include <linux/module.h> >> +#include <linux/of_device.h> >> #include <linux/regmap.h> >> >> static const struct mfd_cell rn5t618_cells[] = { >> @@ -59,12 +61,26 @@ static void rn5t618_power_off(void) >> RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF); >> } >> >> +static const struct of_device_id rn5t618_of_match[] = { >> + { .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 }, >> + { .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, rn5t618_of_match); >> + >> static int rn5t618_i2c_probe(struct i2c_client *i2c, >> const struct i2c_device_id *id) >> { >> + const struct of_device_id *of_id = >> + of_match_device(rn5t618_of_match, &i2c->dev); > > I'd prefer you did the call *after* the variable declarations. > >> struct rn5t618 *priv; >> int ret; > > So here -> >> + if (!of_id) { >> + dev_err(&i2c->dev, "Failed to find matching dt id\n"); > > s/dt id/DT ID/ >> + return -EINVAL; >> + } >> + >> priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL); >> if (!priv) >> return -ENOMEM; >> @@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c, >> return ret; >> } >> >> + priv->variant = (long)of_id->data; >> + > > Why here and not directly after the of_id check? > >> ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells, >> ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL); >> if (ret) { >> @@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c) >> return 0; >> } >> >> -static const struct of_device_id rn5t618_of_match[] = { >> - { .compatible = "ricoh,rn5t618" }, >> - { } >> -}; >> -MODULE_DEVICE_TABLE(of, rn5t618_of_match); >> - >> static const struct i2c_device_id rn5t618_i2c_id[] = { >> { } >> }; >> @@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = { >> module_i2c_driver(rn5t618_i2c_driver); >> >> MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); >> -MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver"); >> +MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver"); >> MODULE_LICENSE("GPL v2"); >> diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h >> index c72d534..54179c2 100644 >> --- a/include/linux/mfd/rn5t618.h >> +++ b/include/linux/mfd/rn5t618.h >> @@ -20,6 +20,7 @@ >> #define RN5T618_OTPVER 0x01 >> #define RN5T618_IODAC 0x02 >> #define RN5T618_VINDAC 0x03 >> +#define RN5T618_OUT32KEN 0x05 >> #define RN5T618_CPUCNT 0x06 >> #define RN5T618_PSWR 0x07 >> #define RN5T618_PONHIS 0x09 >> @@ -38,6 +39,7 @@ >> #define RN5T618_DC1_SLOT 0x16 >> #define RN5T618_DC2_SLOT 0x17 >> #define RN5T618_DC3_SLOT 0x18 >> +#define RN5T618_DC4_SLOT 0x19 >> #define RN5T618_LDO1_SLOT 0x1b >> #define RN5T618_LDO2_SLOT 0x1c >> #define RN5T618_LDO3_SLOT 0x1d >> @@ -54,12 +56,16 @@ >> #define RN5T618_DC2CTL2 0x2f >> #define RN5T618_DC3CTL 0x30 >> #define RN5T618_DC3CTL2 0x31 >> +#define RN5T618_DC4CTL 0x32 >> +#define RN5T618_DC4CTL2 0x33 >> #define RN5T618_DC1DAC 0x36 >> #define RN5T618_DC2DAC 0x37 >> #define RN5T618_DC3DAC 0x38 >> +#define RN5T618_DC4DAC 0x39 >> #define RN5T618_DC1DAC_SLP 0x3b >> #define RN5T618_DC2DAC_SLP 0x3c >> #define RN5T618_DC3DAC_SLP 0x3d >> +#define RN5T618_DC4DAC_SLP 0x3e >> #define RN5T618_DCIREN 0x40 >> #define RN5T618_DCIRQ 0x41 >> #define RN5T618_DCIRMON 0x42 >> @@ -221,8 +227,14 @@ enum { >> RN5T618_REG_NUM, >> }; >> >> +enum { >> + RN5T567 = 0, >> + RN5T618, >> +}; >> + >> struct rn5t618 { >> struct regmap *regmap; >> + long variant; > > What do you use this for? This is used in the regulator driver to detect which variant we are dealing with... Ack on all the other stuff, will send a v3 for this. -- Stefan > >> }; >> >> #endif /* __LINUX_MFD_RN5T618_H */
diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 937785a..5b493ed 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,18 +1,21 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618 is a power management IC family which integrates +3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and +a watchdog timer. The RN5T618 provides additionally a Li-ion battery +charger, fuel gauge and an ADC. It can be controlled through a I2C +interface. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 1bcf601..ff031a7 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -852,13 +852,14 @@ config MFD_RK808 including interrupts, RTC, LDO & DCDC regulators, and onkey. config MFD_RN5T618 - tristate "Ricoh RN5T5618 PMIC" + tristate "Ricoh RN5T567/618 PMIC" depends on I2C + depends on OF select MFD_CORE select REGMAP_I2C help - Say yes here to add support for the Ricoh RN5T618 PMIC. This - driver provides common support for accessing the device, + Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC. + This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c index 0ad51d7..7607ced 100644 --- a/drivers/mfd/rn5t618.c +++ b/drivers/mfd/rn5t618.c @@ -2,6 +2,7 @@ * MFD core driver for Ricoh RN5T618 PMIC * * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> + * Copyright (C) 2016 Toradex AG * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -15,6 +16,7 @@ #include <linux/mfd/core.h> #include <linux/mfd/rn5t618.h> #include <linux/module.h> +#include <linux/of_device.h> #include <linux/regmap.h> static const struct mfd_cell rn5t618_cells[] = { @@ -59,12 +61,26 @@ static void rn5t618_power_off(void) RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF); } +static const struct of_device_id rn5t618_of_match[] = { + { .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 }, + { .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 }, + { } +}; +MODULE_DEVICE_TABLE(of, rn5t618_of_match); + static int rn5t618_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { + const struct of_device_id *of_id = + of_match_device(rn5t618_of_match, &i2c->dev); struct rn5t618 *priv; int ret; + if (!of_id) { + dev_err(&i2c->dev, "Failed to find matching dt id\n"); + return -EINVAL; + } + priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL); if (!priv) return -ENOMEM; @@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c, return ret; } + priv->variant = (long)of_id->data; + ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells, ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL); if (ret) { @@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c) return 0; } -static const struct of_device_id rn5t618_of_match[] = { - { .compatible = "ricoh,rn5t618" }, - { } -}; -MODULE_DEVICE_TABLE(of, rn5t618_of_match); - static const struct i2c_device_id rn5t618_i2c_id[] = { { } }; @@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = { module_i2c_driver(rn5t618_i2c_driver); MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); -MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver"); +MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver"); MODULE_LICENSE("GPL v2"); diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h index c72d534..54179c2 100644 --- a/include/linux/mfd/rn5t618.h +++ b/include/linux/mfd/rn5t618.h @@ -20,6 +20,7 @@ #define RN5T618_OTPVER 0x01 #define RN5T618_IODAC 0x02 #define RN5T618_VINDAC 0x03 +#define RN5T618_OUT32KEN 0x05 #define RN5T618_CPUCNT 0x06 #define RN5T618_PSWR 0x07 #define RN5T618_PONHIS 0x09 @@ -38,6 +39,7 @@ #define RN5T618_DC1_SLOT 0x16 #define RN5T618_DC2_SLOT 0x17 #define RN5T618_DC3_SLOT 0x18 +#define RN5T618_DC4_SLOT 0x19 #define RN5T618_LDO1_SLOT 0x1b #define RN5T618_LDO2_SLOT 0x1c #define RN5T618_LDO3_SLOT 0x1d @@ -54,12 +56,16 @@ #define RN5T618_DC2CTL2 0x2f #define RN5T618_DC3CTL 0x30 #define RN5T618_DC3CTL2 0x31 +#define RN5T618_DC4CTL 0x32 +#define RN5T618_DC4CTL2 0x33 #define RN5T618_DC1DAC 0x36 #define RN5T618_DC2DAC 0x37 #define RN5T618_DC3DAC 0x38 +#define RN5T618_DC4DAC 0x39 #define RN5T618_DC1DAC_SLP 0x3b #define RN5T618_DC2DAC_SLP 0x3c #define RN5T618_DC3DAC_SLP 0x3d +#define RN5T618_DC4DAC_SLP 0x3e #define RN5T618_DCIREN 0x40 #define RN5T618_DCIRQ 0x41 #define RN5T618_DCIRMON 0x42 @@ -221,8 +227,14 @@ enum { RN5T618_REG_NUM, }; +enum { + RN5T567 = 0, + RN5T618, +}; + struct rn5t618 { struct regmap *regmap; + long variant; }; #endif /* __LINUX_MFD_RN5T618_H */