new file mode 100644
@@ -0,0 +1,36 @@
+* GSL 1680 touchscreen controller
+
+Required properties:
+- compatible : "silead,gsl1680"
+- reg : I2C slave address of the chip (0x40)
+- interrupt-parent : a phandle pointing to the interrupt controller
+ serving the interrupt for this chip
+- interrupts : interrupt specification for the gsl1680 interrupt
+- power-gpios : Specification for the pin connected to the gsl1680's
+ shutdown input. This needs to be driven high to take the
+ gsl1680 out of its low power state
+- touchscreen-size-x : See touchscreen.txt
+- touchscreen-size-y : See touchscreen.txt
+- touchscreen-max-fingers : See touchscreen.txt
+
+Optional properties:
+- touchscreen-inverted-x : See touchscreen.txt
+- touchscreen-inverted-y : See touchscreen.txt
+- touchscreen-swapped-x-y : See touchscreen.txt
+
+Example:
+
+i2c@00000000 {
+ gsl1680: touchscreen@40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>;
+ power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>;
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+ touchscreen-max-fingers = <5>;
+ touchscreen-inverted-x;
+ touchscreen-swapped-x-y;
+ };
+};
@@ -20,6 +20,8 @@ Optional properties for Touchscreens:
Swapping is done after inverting the axis
- touchscreen-x-mm : horizontal length in mm of the touchscreen
- touchscreen-y-mm : vertical length in mm of the touchscreen
+ - touchscreen-max-fingers : maximum number of fingers the touchscreen
+ can detect
Deprecated properties for Touchscreens:
- x-size : deprecated name for touchscreen-size-x
@@ -1181,4 +1181,17 @@ config TOUCHSCREEN_ROHM_BU21023
To compile this driver as a module, choose M here: the
module will be called bu21023_ts.
+config TOUCHSCREEN_SILEAD
+ tristate "Silead I2C touchscreen"
+ depends on I2C
+ help
+ Say Y here if you have the Silead touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called silead.
+
+
endif
@@ -97,3 +97,4 @@ obj-$(CONFIG_TOUCHSCREEN_TPS6507X) += tps6507x-ts.o
obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o
obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50) += colibri-vf50-ts.o
obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o
+obj-$(CONFIG_TOUCHSCREEN_SILEAD) += silead.o
new file mode 100644
@@ -0,0 +1,572 @@
+/* -------------------------------------------------------------------------
+ * Copyright (C) 2014-2015, Intel Corporation
+ *
+ * Derived from:
+ * gslX68X.c
+ * Copyright (C) 2010-2015, Shanghai Sileadinc Co.Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ * -------------------------------------------------------------------------
+ */
+
+#include <asm/unaligned.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/acpi.h>
+#include <linux/interrupt.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/pm.h>
+#include <linux/irq.h>
+
+#define SILEAD_TS_NAME "silead_ts"
+
+#define SILEAD_REG_RESET 0xE0
+#define SILEAD_REG_DATA 0x80
+#define SILEAD_REG_TOUCH_NR 0x80
+#define SILEAD_REG_POWER 0xBC
+#define SILEAD_REG_CLOCK 0xE4
+#define SILEAD_REG_STATUS 0xB0
+#define SILEAD_REG_ID 0xFC
+#define SILEAD_REG_MEM_CHECK 0xB0
+
+#define SILEAD_STATUS_OK 0x5A5A5A5A
+#define SILEAD_TS_DATA_LEN 44
+#define SILEAD_CLOCK 0x04
+
+#define SILEAD_CMD_RESET 0x88
+#define SILEAD_CMD_START 0x00
+
+#define SILEAD_POINT_DATA_LEN 0x04
+#define SILEAD_POINT_Y_OFF 0x00
+#define SILEAD_POINT_Y_MSB_OFF 0x01
+#define SILEAD_POINT_X_OFF 0x02
+#define SILEAD_POINT_X_MSB_OFF 0x03
+#define SILEAD_TOUCH_ID_MASK 0xF0
+
+#define SILEAD_CMD_SLEEP_MIN 10000
+#define SILEAD_CMD_SLEEP_MAX 20000
+#define SILEAD_POWER_SLEEP 20
+#define SILEAD_STARTUP_SLEEP 30
+
+#define SILEAD_MAX_FINGERS 10
+
+enum silead_ts_power {
+ SILEAD_POWER_ON = 1,
+ SILEAD_POWER_OFF = 0
+};
+
+struct silead_ts_data {
+ struct i2c_client *client;
+ struct gpio_desc *gpio_power;
+ struct input_dev *input;
+ char fw_name[64];
+ struct touchscreen_properties prop;
+ u32 max_fingers;
+ u32 chip_id;
+ struct input_mt_pos pos[SILEAD_MAX_FINGERS];
+ int slots[SILEAD_MAX_FINGERS];
+ int id[SILEAD_MAX_FINGERS];
+};
+
+struct silead_fw_data {
+ u32 offset;
+ u32 val;
+};
+
+static int silead_ts_request_input_dev(struct silead_ts_data *data)
+{
+ struct device *dev = &data->client->dev;
+ int error;
+
+ data->input = devm_input_allocate_device(dev);
+ if (!data->input) {
+ dev_err(dev,
+ "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ input_set_abs_params(data->input, ABS_MT_POSITION_X, 0, 4095, 0, 0);
+ input_set_abs_params(data->input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
+ touchscreen_parse_properties(data->input, true, &data->prop);
+
+ input_mt_init_slots(data->input, data->max_fingers,
+ INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED |
+ INPUT_MT_TRACK);
+
+ data->input->name = SILEAD_TS_NAME;
+ data->input->phys = "input/ts";
+ data->input->id.bustype = BUS_I2C;
+
+ error = input_register_device(data->input);
+ if (error) {
+ dev_err(dev, "Failed to register input device: %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static void silead_ts_set_power(struct i2c_client *client,
+ enum silead_ts_power state)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+
+ if (data->gpio_power) {
+ gpiod_set_value_cansleep(data->gpio_power, state);
+ msleep(SILEAD_POWER_SLEEP);
+ }
+}
+
+static void silead_ts_read_data(struct i2c_client *client)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ struct input_dev *input = data->input;
+ struct device *dev = &client->dev;
+ u8 *bufp, buf[SILEAD_TS_DATA_LEN];
+ int touch_nr, error, i;
+
+ error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_DATA,
+ SILEAD_TS_DATA_LEN, buf);
+ if (error < 0) {
+ dev_err(dev, "Data read error %d\n", error);
+ return;
+ }
+
+ touch_nr = buf[0];
+ if (touch_nr < 0)
+ return;
+
+ if (touch_nr > data->max_fingers) {
+ dev_warn(dev, "More touches reported then supported %d > %d\n",
+ touch_nr, data->max_fingers);
+ touch_nr = data->max_fingers;
+ }
+
+ bufp = buf + SILEAD_POINT_DATA_LEN;
+ for (i = 0; i < touch_nr; i++, bufp += SILEAD_POINT_DATA_LEN) {
+ /* Bits 4-7 are the touch id */
+ data->id[i] = (bufp[SILEAD_POINT_X_MSB_OFF] &
+ SILEAD_TOUCH_ID_MASK) >> 4;
+ touchscreen_set_mt_pos(&data->pos[i], &data->prop,
+ get_unaligned_le16(&bufp[SILEAD_POINT_X_OFF]) & 0xfff,
+ get_unaligned_le16(&bufp[SILEAD_POINT_Y_OFF]) & 0xfff);
+ }
+
+ input_mt_assign_slots(input, data->slots, data->pos, touch_nr, 0);
+
+ for (i = 0; i < touch_nr; i++) {
+ input_mt_slot(input, data->slots[i]);
+ input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+ input_report_abs(input, ABS_MT_POSITION_X, data->pos[i].x);
+ input_report_abs(input, ABS_MT_POSITION_Y, data->pos[i].y);
+
+ dev_dbg(dev, "x=%d y=%d hw_id=%d sw_id=%d\n", data->pos[i].x,
+ data->pos[i].y, data->id[i], data->slots[i]);
+ }
+
+ input_mt_sync_frame(input);
+ input_sync(input);
+}
+
+static int silead_ts_init(struct i2c_client *client)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ int error;
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+ SILEAD_CMD_RESET);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_TOUCH_NR,
+ data->max_fingers);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_CLOCK,
+ SILEAD_CLOCK);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+ SILEAD_CMD_START);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ return 0;
+
+i2c_write_err:
+ dev_err(&client->dev, "Registers clear error %d\n", error);
+ return error;
+}
+
+static int silead_ts_reset(struct i2c_client *client)
+{
+ int error;
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+ SILEAD_CMD_RESET);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_CLOCK,
+ SILEAD_CLOCK);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_POWER,
+ SILEAD_CMD_START);
+ if (error)
+ goto i2c_write_err;
+ usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+ return 0;
+
+i2c_write_err:
+ dev_err(&client->dev, "Chip reset error %d\n", error);
+ return error;
+}
+
+static int silead_ts_startup(struct i2c_client *client)
+{
+ int error;
+
+ error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET, 0x00);
+ if (error) {
+ dev_err(&client->dev, "Startup error %d\n", error);
+ return error;
+ }
+ msleep(SILEAD_STARTUP_SLEEP);
+
+ return 0;
+}
+
+static int silead_ts_load_fw(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ unsigned int fw_size, i;
+ const struct firmware *fw;
+ struct silead_fw_data *fw_data;
+ int error;
+
+ dev_dbg(dev, "Firmware file name: %s", data->fw_name);
+
+ error = request_firmware(&fw, data->fw_name, dev);
+ if (error) {
+ dev_err(dev, "Firmware request error %d\n", error);
+ return error;
+ }
+
+ fw_size = fw->size / sizeof(*fw_data);
+ fw_data = (struct silead_fw_data *)fw->data;
+
+ for (i = 0; i < fw_size; i++) {
+ error = i2c_smbus_write_i2c_block_data(client,
+ fw_data[i].offset,
+ 4,
+ (u8 *)&fw_data[i].val);
+ if (error) {
+ dev_err(dev, "Firmware load error %d\n", error);
+ goto release_fw_err;
+ }
+ }
+
+ release_firmware(fw);
+ return 0;
+
+release_fw_err:
+ release_firmware(fw);
+ return error;
+}
+
+static u32 silead_ts_get_status(struct i2c_client *client)
+{
+ int error;
+ u32 status;
+
+ error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_STATUS, 4,
+ (u8 *)&status);
+ if (error < 0) {
+ dev_err(&client->dev, "Status read error %d\n", error);
+ return error;
+ }
+
+ return le32_to_cpu(status);
+}
+
+static int silead_ts_get_id(struct i2c_client *client)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ int error;
+
+ error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_ID, 4,
+ (u8 *)&data->chip_id);
+
+ data->chip_id = le32_to_cpu(data->chip_id);
+
+ if (error < 0) {
+ dev_err(&client->dev, "Chip ID read error %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int silead_ts_setup(struct i2c_client *client)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ struct device *dev = &client->dev;
+ int error;
+ u32 status;
+
+ silead_ts_set_power(client, SILEAD_POWER_OFF);
+ silead_ts_set_power(client, SILEAD_POWER_ON);
+
+ error = silead_ts_get_id(client);
+ if (error)
+ return error;
+ dev_info(dev, "Silead chip ID: 0x%8X", data->chip_id);
+
+ error = silead_ts_init(client);
+ if (error)
+ return error;
+
+ error = silead_ts_reset(client);
+ if (error)
+ return error;
+
+ error = silead_ts_load_fw(client);
+ if (error)
+ return error;
+
+ error = silead_ts_startup(client);
+ if (error)
+ return error;
+
+ status = silead_ts_get_status(client);
+ if (status != SILEAD_STATUS_OK) {
+ dev_err(dev, "Initialization error, status: 0x%X\n", status);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static irqreturn_t silead_ts_threaded_irq_handler(int irq, void *id)
+{
+ struct silead_ts_data *data = id;
+ struct i2c_client *client = data->client;
+
+ silead_ts_read_data(client);
+
+ return IRQ_HANDLED;
+}
+
+static void silead_ts_read_props(struct i2c_client *client)
+{
+ struct silead_ts_data *data = i2c_get_clientdata(client);
+ struct device *dev = &client->dev;
+ const char *str;
+ int error;
+
+ error = device_property_read_u32(dev, "touchscreen-max-fingers",
+ &data->max_fingers);
+ if (error) {
+ dev_dbg(dev, "Max fingers read error %d\n", error);
+ data->max_fingers = 5; /* Most devices handle up-to 5 fingers */
+ }
+
+ error = device_property_read_string(dev, "touchscreen-fw-name", &str);
+ if (!error)
+ snprintf(data->fw_name, sizeof(data->fw_name), "%s", str);
+ else
+ dev_dbg(dev, "Firmware file name read error. Using default.");
+}
+
+#ifdef CONFIG_ACPI
+static int silead_ts_set_default_fw_name(struct silead_ts_data *data,
+ const struct i2c_device_id *id)
+{
+ const struct acpi_device_id *acpi_id;
+ struct device *dev = &data->client->dev;
+ int i;
+
+ if (ACPI_HANDLE(dev)) {
+ acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev);
+ if (!acpi_id)
+ return -ENODEV;
+
+ snprintf(data->fw_name, sizeof(data->fw_name), "%s.fw",
+ acpi_id->id);
+
+ for (i = 0; i < strlen(data->fw_name); i++)
+ data->fw_name[i] = tolower(data->fw_name[i]);
+ } else {
+ snprintf(data->fw_name, sizeof(data->fw_name), "%s.fw",
+ id->name);
+ }
+
+ return 0;
+}
+#else
+static int silead_ts_set_default_fw_name(struct silead_ts_data *data,
+ const struct i2c_device_id *id)
+{
+ snprintf(data->fw_name, sizeof(data->fw_name), "%s.fw", id->name);
+ return 0;
+}
+#endif
+
+static int silead_ts_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct silead_ts_data *data;
+ struct device *dev = &client->dev;
+ int error;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_I2C |
+ I2C_FUNC_SMBUS_READ_I2C_BLOCK |
+ I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+ dev_err(dev, "I2C functionality check failed\n");
+ return -ENXIO;
+ }
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, data);
+ data->client = client;
+
+ error = silead_ts_set_default_fw_name(data, id);
+ if (error)
+ return error;
+
+ silead_ts_read_props(client);
+
+ /* We must have the IRQ provided by DT or ACPI subsytem */
+ if (client->irq <= 0)
+ return -ENODEV;
+
+ /* Power GPIO pin */
+ data->gpio_power = gpiod_get_optional(dev, "power", GPIOD_OUT_LOW);
+ if (IS_ERR(data->gpio_power)) {
+ if (PTR_ERR(data->gpio_power) != -EPROBE_DEFER)
+ dev_err(dev, "Shutdown GPIO request failed\n");
+ return PTR_ERR(data->gpio_power);
+ }
+
+ error = silead_ts_setup(client);
+ if (error)
+ return error;
+
+ error = silead_ts_request_input_dev(data);
+ if (error)
+ return error;
+
+ error = devm_request_threaded_irq(dev, client->irq, NULL,
+ silead_ts_threaded_irq_handler, IRQF_ONESHOT,
+ client->name, data);
+ if (error) {
+ if (error != -EPROBE_DEFER)
+ dev_err(dev, "IRQ request failed %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int __maybe_unused silead_ts_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+
+ silead_ts_set_power(client, SILEAD_POWER_OFF);
+ return 0;
+}
+
+static int __maybe_unused silead_ts_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ int error, status;
+
+ silead_ts_set_power(client, SILEAD_POWER_ON);
+
+ error = silead_ts_reset(client);
+ if (error)
+ return error;
+
+ error = silead_ts_startup(client);
+ if (error)
+ return error;
+
+ status = silead_ts_get_status(client);
+ if (status != SILEAD_STATUS_OK) {
+ dev_err(dev, "Resume error, status: 0x%02x\n", status);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(silead_ts_pm, silead_ts_suspend, silead_ts_resume);
+
+static const struct i2c_device_id silead_ts_id[] = {
+ { "gsl1680", 0 },
+ { "gsl1688", 0 },
+ { "gsl3670", 0 },
+ { "gsl3675", 0 },
+ { "gsl3692", 0 },
+ { "mssl1680", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, silead_ts_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id silead_ts_acpi_match[] = {
+ { "GSL1680", 0 },
+ { "GSL1688", 0 },
+ { "GSL3670", 0 },
+ { "GSL3675", 0 },
+ { "GSL3692", 0 },
+ { "MSSL1680", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, silead_ts_acpi_match);
+#endif
+
+static struct i2c_driver silead_ts_driver = {
+ .probe = silead_ts_probe,
+ .id_table = silead_ts_id,
+ .driver = {
+ .name = SILEAD_TS_NAME,
+ .owner = THIS_MODULE,
+ .acpi_match_table = ACPI_PTR(silead_ts_acpi_match),
+ .pm = &silead_ts_pm,
+ },
+};
+module_i2c_driver(silead_ts_driver);
+
+MODULE_AUTHOR("Robert Dolca <robert.dolca@intel.com>");
+MODULE_DESCRIPTION("Silead I2C touchscreen driver");
+MODULE_LICENSE("GPL");