| Message ID | 1471848557-27278-8-git-send-email-wenyou.yang@atmel.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
Hi, On Mon, Aug 22, 2016 at 02:49:17PM +0800, Wenyou Yang wrote: > Due the driver improvements, update the properties, > - Remove "active-semi,check-battery-temperature" property. > - Add the properties, "active-semi,irq_gpio" > and "active-semi,lbo-gpios". > > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> > Acked-by: Rob Herring <robh@kernel.org> I wonder if it's too late to slightly break the DT API by introducing a proper sub-device for the charger and having all those charger specific details described there. Not being able to use the devm_ functions because all properties are assigned to the parent device is not very nice. We could easily support reading timeouts and threshold information from the both (parent and sub-device) and just mark the parent binding deprecated. The only real API break would be "active-semi,chglev-gpios", which is currently broken anyways in the driver as far as I can see (I should have reviewed this more carefully previously). In other words I suggest the following: pmic@5b { compatible = "active-semi,act8945a"; reg = <0x5b>; status = "okay"; /* the following 3 are deprecated, but still supported */ //active-semi,input-voltage-threshold-microvolt = <6600>; //active-semi,precondition-timeout = <40>; //active-semi,total-timeout = <3>; /* no longer supported, never worked properly */ //active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; /* this is new, mfd should register charger sub-dev independently * of the subnode for backwards compatibility. Then optional * gpios/irqs are not available. But those either never worked * or did not exist before this update. */ charger { active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; interrupt-parent = <&pioA>; interrupts = <45 GPIO_ACTIVE_LOW> active-semi,input-voltage-threshold-microvolt = <6600>; active-semi,precondition-timeout = <40>; active-semi,total-timeout = <3>; }; }; -- Sebastian
diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt index bea254c..f9866c4 100644 --- a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -4,10 +4,15 @@ Required properties: - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. - active-semi,chglev-gpios: charge current level phandle with args as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. + - interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. Optional properties: - - active-semi,check-battery-temperature: boolean to check the battery - temperature or not. - active-semi,input-voltage-threshold-microvolt: unit: mV; Specifies the charger's input over-voltage threshold value; The value can be: 6600, 7000, 7500, 8000; default: 6600 @@ -27,9 +32,14 @@ Example: status = "okay"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_chglev>; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; active-semi,input-voltage-threshold-microvolt = <6600>; active-semi,precondition-timeout = <40>; active-semi,total-timeout = <3>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + };