@@ -261,6 +261,15 @@ config IR_REDRAT3
To compile this driver as a module, choose M here: the
module will be called redrat3.
+config IR_SPI
+ tristate "SPI connected IR LED"
+ depends on SPI && LIRC
+ ---help---
+ Say Y if you want to use an IR LED connected through SPI bus.
+
+ To compile this driver as a module, choose M here: the module will be
+ called ir-spi.
+
config IR_STREAMZAP
tristate "Streamzap PC Remote IR Receiver"
depends on USB_ARCH_HAS_HCD
@@ -27,6 +27,7 @@ obj-$(CONFIG_IR_NUVOTON) += nuvoton-cir.o
obj-$(CONFIG_IR_ENE) += ene_ir.o
obj-$(CONFIG_IR_REDRAT3) += redrat3.o
obj-$(CONFIG_IR_RX51) += ir-rx51.o
+obj-$(CONFIG_IR_SPI) += ir-spi.o
obj-$(CONFIG_IR_STREAMZAP) += streamzap.o
obj-$(CONFIG_IR_WINBOND_CIR) += winbond-cir.o
obj-$(CONFIG_RC_LOOPBACK) += rc-loopback.o
new file mode 100644
@@ -0,0 +1,221 @@
+/*
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ * Author: Andi Shyti <andi.shyti@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * SPI driven IR LED device driver
+ */
+
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <media/rc-core.h>
+
+#define IR_SPI_DRIVER_NAME "ir-spi"
+
+/* pulse value for different duty cycles */
+#define IR_SPI_PULSE_DC_50 0xff00
+#define IR_SPI_PULSE_DC_60 0xfc00
+#define IR_SPI_PULSE_DC_70 0xf800
+#define IR_SPI_PULSE_DC_75 0xf000
+#define IR_SPI_PULSE_DC_80 0xc000
+#define IR_SPI_PULSE_DC_90 0x8000
+
+/* duty cycles values */
+#define IR_SPI_DUTY_CYCLE_50 50
+#define IR_SPI_DUTY_CYCLE_60 60
+#define IR_SPI_DUTY_CYCLE_70 70
+#define IR_SPI_DUTY_CYCLE_75 75
+#define IR_SPI_DUTY_CYCLE_80 80
+#define IR_SPI_DUTY_CYCLE_90 90
+
+#define IR_SPI_DEFAULT_FREQUENCY 38000
+#define IR_SPI_BIT_PER_WORD 8
+#define IR_SPI_MAX_BUFSIZE 4096
+
+struct ir_spi_data {
+ u32 freq;
+ u8 duty_cycle;
+ bool negated;
+
+ u16 tx_buf[IR_SPI_MAX_BUFSIZE];
+ u16 pulse;
+ u16 space;
+
+ struct rc_dev *rc;
+ struct spi_device *spi;
+ struct regulator *regulator;
+};
+
+static int ir_spi_tx(struct rc_dev *dev, unsigned int *buffer, unsigned int count)
+{
+ int i;
+ int ret;
+ unsigned int len = 0;
+ struct ir_spi_data *idata = dev->priv;
+ struct spi_transfer xfer;
+
+ /* convert the pulse/space signal to raw binary signal */
+ for (i = 0; i < count; i++) {
+ int j;
+ u16 val = ((i+1) % 2) ? idata->pulse : idata->space;
+
+ if (len + buffer[i] >= IR_SPI_MAX_BUFSIZE)
+ return -EINVAL;
+
+ /*
+ * the first value in buffer is a pulse, so that 0, 2, 4, ...
+ * contain a pulse duration. On the contrary, 1, 3, 5, ...
+ * contain a space duration.
+ */
+ val = (i % 2) ? idata->space : idata->pulse;
+ for (j = 0; j < buffer[i]; j++)
+ idata->tx_buf[len++] = val;
+ }
+
+ pr_info("from %u data, we originated %u raw data\n", count, len);
+
+ memset(&xfer, 0, sizeof(xfer));
+
+ xfer.speed_hz = idata->freq;
+ xfer.len = len * sizeof(*idata->tx_buf);
+ xfer.tx_buf = idata->tx_buf;
+
+ ret = regulator_enable(idata->regulator);
+ if (ret)
+ return ret;
+
+ ret = spi_sync_transfer(idata->spi, &xfer, 1);
+ if (ret)
+ dev_err(&idata->spi->dev, "unable to deliver the signal\n");
+
+ regulator_disable(idata->regulator);
+
+ return ret ? ret : len;
+}
+
+static int ir_spi_set_tx_carrier(struct rc_dev *dev, u32 carrier)
+{
+ struct ir_spi_data *idata = dev->priv;
+
+ if (!carrier)
+ return -EINVAL;
+
+ idata->freq = carrier;
+
+ return 0;
+}
+
+static int ir_spi_set_duty_cycle(struct rc_dev *dev, u32 duty_cycle)
+{
+ struct ir_spi_data *idata = dev->priv;
+
+ switch (duty_cycle) {
+ case IR_SPI_DUTY_CYCLE_90:
+ idata->pulse = IR_SPI_PULSE_DC_90;
+ break;
+ case IR_SPI_DUTY_CYCLE_80:
+ idata->pulse = IR_SPI_PULSE_DC_80;
+ break;
+ case IR_SPI_DUTY_CYCLE_75:
+ idata->pulse = IR_SPI_PULSE_DC_75;
+ break;
+ case IR_SPI_DUTY_CYCLE_70:
+ idata->pulse = IR_SPI_PULSE_DC_70;
+ break;
+ case IR_SPI_DUTY_CYCLE_60:
+ idata->pulse = IR_SPI_PULSE_DC_60;
+ break;
+ case IR_SPI_DUTY_CYCLE_50:
+ default:
+ idata->pulse = IR_SPI_PULSE_DC_50;
+ }
+
+ if (idata->negated) {
+ idata->pulse = ~idata->pulse;
+ idata->space = 0xffff;
+ } else {
+ idata->space = 0;
+ }
+
+ return 0;
+}
+
+static int ir_spi_probe(struct spi_device *spi)
+{
+ int ret;
+ u8 dc;
+ struct ir_spi_data *idata;
+
+ idata = devm_kzalloc(&spi->dev, sizeof(*idata), GFP_KERNEL);
+ if (!idata)
+ return -ENOMEM;
+
+ idata->regulator = devm_regulator_get(&spi->dev, "irda_regulator");
+ if (IS_ERR(idata->regulator))
+ return PTR_ERR(idata->regulator);
+
+ idata->rc = rc_allocate_device(RC_DRIVER_IR_RAW_TX);
+ if (!idata->rc)
+ return -ENOMEM;
+
+ idata->rc->tx_ir = ir_spi_tx;
+ idata->rc->s_tx_carrier = ir_spi_set_tx_carrier;
+ idata->rc->s_tx_duty_cycle = ir_spi_set_duty_cycle;
+ idata->rc->driver_name = IR_SPI_DRIVER_NAME;
+ idata->rc->priv = idata;
+ idata->spi = spi;
+
+ idata->negated = of_property_read_bool(spi->dev.of_node, "negated");
+ ret = of_property_read_u8(spi->dev.of_node, "duty-cycle", &dc);
+ if (ret)
+ dc = IR_SPI_DUTY_CYCLE_50;
+
+ ret = ir_spi_set_duty_cycle(idata->rc, dc);
+ if (ret)
+ return ret;
+
+ idata->freq = IR_SPI_DEFAULT_FREQUENCY;
+
+ ret = rc_register_device(idata->rc);
+ if (ret)
+ rc_unregister_device(idata->rc);
+
+ return ret;
+}
+
+static int ir_spi_remove(struct spi_device *spi)
+{
+ struct ir_spi_data *idata = spi_get_drvdata(spi);
+
+ rc_unregister_device(idata->rc);
+
+ return 0;
+}
+
+static const struct of_device_id ir_spi_of_match[] = {
+ { .compatible = "ir-spi" },
+ {},
+};
+
+static struct spi_driver ir_spi_driver = {
+ .probe = ir_spi_probe,
+ .remove = ir_spi_remove,
+ .driver = {
+ .name = IR_SPI_DRIVER_NAME,
+ .of_match_table = ir_spi_of_match,
+ },
+};
+
+module_spi_driver(ir_spi_driver);
+
+MODULE_AUTHOR("Andi Shyti <andi.shyti@samsung.com>");
+MODULE_DESCRIPTION("SPI IR LED");
+MODULE_LICENSE("GPL v2");
The ir-spi is a simple device driver which supports the connection between an IR LED and the MOSI line of an SPI device. The driver, indeed, uses the SPI framework to stream the raw data provided by userspace through an rc character device. The chardev is handled by the LIRC framework and its functionality basically provides: - write: the driver gets a pulse/space signal and translates it to a binary signal that will be streamed to the IR led through the SPI framework. - set frequency: sets the frequency whith which the data should be sent. This is handle with ioctl with the LIRC_SET_SEND_CARRIER flag (as per lirc documentation) - set duty cycle: this is also handled with ioctl with the LIRC_SET_SEND_DUTY_CYCLE flag. The driver handles duty cycles of 50%, 60%, 70%, 75%, 80% and 90%, calculated on 16bit data. The character device is created under /dev/lircX name, where X is and ID assigned by the LIRC framework. Example of usage: fd = open("/dev/lirc0", O_RDWR); if (fd < 0) return -1; val = 608000; ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val); if (ret < 0) return -1; val = 60; ret = ioctl(fd, LIRC_SET_SEND_DUTY_CYCLE, &val); if (ret < 0) return -1; n = write(fd, buffer, BUF_LEN); if (n < 0 || n != BUF_LEN) ret = -1; close(fd); Signed-off-by: Andi Shyti <andi.shyti@samsung.com> --- drivers/media/rc/Kconfig | 9 ++ drivers/media/rc/Makefile | 1 + drivers/media/rc/ir-spi.c | 221 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 231 insertions(+) create mode 100644 drivers/media/rc/ir-spi.c