@@ -6,12 +6,13 @@ axp202 (X-Powers)
axp209 (X-Powers)
axp221 (X-Powers)
axp223 (X-Powers)
+axp803 (X-Powers)
axp809 (X-Powers)
Required properties:
- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
- "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
- "x-powers,axp809"
+ "x-powers,axp221", "x-powers,axp223", "x-powers,axp803",
+ "x-powers,axp806", "x-powers,axp809"
- reg: The I2C slave address or RSB hardware address for the AXP chip
- interrupt-parent: The parent interrupt controller
- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -86,6 +87,33 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
RTC_LDO : LDO : ips-supply : always on
DRIVEVBUS : Enable output : drivevbus-supply : external regulator
+AXP803 regulators, type, and corresponding input supply names:
+
+Regulator Type Supply Name Notes
+--------- ---- ----------- -----
+DCDC1 : DC-DC buck : vin1-supply
+DCDC2 : DC-DC buck : vin2-supply
+DCDC3 : DC-DC buck : vin3-supply
+DCDC4 : DC-DC buck : vin4-supply
+DCDC5 : DC-DC buck : vin5-supply
+DCDC6 : DC-DC buck : vin6-supply
+ALDO1 : LDO : aldoin-supply : shared supply
+ALDO2 : LDO : aldoin-supply : shared supply
+ALDO3 : LDO : aldoin-supply : shared supply
+DLDO1 : LDO : dldoin-supply : shared supply
+DLDO2 : LDO : dldoin-supply : shared supply
+DLDO3 : LDO : dldoin-supply : shared supply
+DLDO4 : LDO : dldoin-supply : shared supply
+ELDO1 : LDO : eldoin-supply : shared supply
+ELDO2 : LDO : eldoin-supply : shared supply
+ELDO3 : LDO : eldoin-supply : shared supply
+FLDO1 : LDO : fldoin-supply : shared supply
+FLDO2 : LDO : fldoin-supply : shared supply
+RTC_LDO : LDO : ips-supply : always on
+LDO_IO0 : LDO : ips-supply : GPIO 0
+LDO_IO1 : LDO : ips-supply : GPIO 1
+DC1SW : On/Off Switch : : DCDC1 secondary output
+
AXP806 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
@@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
"AXP221",
"AXP223",
"AXP288",
+ "AXP803",
"AXP806",
"AXP809",
};
@@ -739,6 +740,14 @@ static struct mfd_cell axp809_cells[] = {
},
};
+static struct mfd_cell axp803_cells[] = {
+ {
+ .name = "axp20x-pek",
+ .num_resources = ARRAY_SIZE(axp809_pek_resources),
+ .resources = axp809_pek_resources,
+ },
+};
+
static struct axp20x_dev *axp20x_pm_power_off;
static void axp20x_power_off(void)
{
@@ -801,6 +810,10 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
axp20x->regmap_cfg = &axp288_regmap_config;
axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
break;
+ case AXP803_ID:
+ axp20x->cells = axp803_cells;
+ axp20x->nr_cells = ARRAY_SIZE(axp803_cells);
+ break;
case AXP806_ID:
axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
axp20x->cells = axp806_cells;
@@ -21,7 +21,8 @@ obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
obj-$(CONFIG_REGULATOR_ARIZONA) += arizona-micsupp.o arizona-ldo1.o
obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
-obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o axp-regulator.o
+obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o axp-regulator.o \
+ axp803.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
new file mode 100644
@@ -0,0 +1,225 @@
+/*
+ * AXP803 regulator driver
+ *
+ * Copyright (C) 2016 Jean-Francois Moine <moinejf@free.fr>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/regulator/driver.h>
+#include <linux/sunxi-rsb.h>
+
+#include "axp-regulator.h"
+
+enum {
+ AXP803_DLDO1 = 0,
+ AXP803_DLDO2,
+ AXP803_DLDO3,
+ AXP803_DLDO4,
+ AXP803_ELDO1,
+ AXP803_ELDO2,
+ AXP803_ELDO3,
+ AXP803_FLDO1,
+ AXP803_FLDO2,
+ AXP803_DCDC1,
+ AXP803_DCDC2,
+ AXP803_DCDC3,
+ AXP803_DCDC4,
+ AXP803_DCDC5,
+ AXP803_DCDC6,
+ AXP803_ALDO1,
+ AXP803_ALDO2,
+ AXP803_ALDO3,
+ AXP803_LDO_IO0,
+ AXP803_LDO_IO1,
+ AXP803_RTC_LDO,
+ AXP803_DC1SW,
+};
+
+/* AXP803 registers */
+#define AXP803_FLDO1_V_OUT 0x1c
+#define AXP803_FLDO2_V_OUT 0x1d
+#define AXP803_DCDC1_V_OUT 0x20
+#define AXP803_DCDC2_V_OUT 0x21
+#define AXP803_DCDC3_V_OUT 0x22
+#define AXP803_DCDC4_V_OUT 0x23
+#define AXP803_DCDC5_V_OUT 0x24
+#define AXP803_DCDC6_V_OUT 0x25
+
+static const struct regulator_linear_range axp803_dldo2_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0, 26, 100000),
+ REGULATOR_LINEAR_RANGE(3400000, 27, 31, 200000),
+};
+
+static const struct regulator_linear_range axp803_dcdc2_4_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 71, 10000),
+ REGULATOR_LINEAR_RANGE(1220000, 72, 76, 20000),
+};
+
+static const struct regulator_linear_range axp803_dcdc5_ranges[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0, 33, 10000),
+ REGULATOR_LINEAR_RANGE(1140000, 34, 69, 20000),
+};
+
+static const struct regulator_linear_range axp803_dcdc6_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0, 51, 10000),
+ REGULATOR_LINEAR_RANGE(1120000, 52, 72, 20000),
+};
+
+static const struct regulator_desc axp803_regulators[] = {
+ AXP_DESC(AXP803, DLDO1, "dldo1", "dldoin", 700, 3300, 100,
+ AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(3)),
+ AXP_DESC_RANGES(AXP803, DLDO2, "dldo2", "dldoin", axp803_dldo2_ranges,
+ 31, AXP22X_DLDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
+ BIT(4)),
+ AXP_DESC(AXP803, DLDO3, "dldo3", "dldoin", 700, 3300, 100,
+ AXP22X_DLDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
+ AXP_DESC(AXP803, DLDO4, "dldo4", "dldoin", 700, 3300, 100,
+ AXP22X_DLDO4_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(6)),
+ AXP_DESC(AXP803, ELDO1, "eldo1", "eldoin", 700, 1900, 50,
+ AXP22X_ELDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(0)),
+ AXP_DESC(AXP803, ELDO2, "eldo2", "eldoin", 700, 1900, 50,
+ AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)),
+ AXP_DESC(AXP803, ELDO3, "eldo3", "eldoin", 700, 1900, 50,
+ AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)),
+ AXP_DESC(AXP803, FLDO1, "fldo1", "fldoin", 700, 1450, 50,
+ AXP803_FLDO1_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(2)),
+ AXP_DESC(AXP803, FLDO2, "fldo2", "fldoin", 700, 1450, 50,
+ AXP803_FLDO2_V_OUT, 0x0f, AXP22X_PWR_OUT_CTRL3, BIT(3)),
+ AXP_DESC(AXP803, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
+ AXP803_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(0)),
+ AXP_DESC_RANGES(AXP803, DCDC2, "dcdc2", "vin2", axp803_dcdc2_4_ranges,
+ 76, AXP803_DCDC2_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
+ BIT(1)),
+ AXP_DESC_RANGES(AXP803, DCDC3, "dcdc3", "vin3", axp803_dcdc2_4_ranges,
+ 76, AXP803_DCDC3_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
+ BIT(2)),
+ AXP_DESC_RANGES(AXP803, DCDC4, "dcdc4", "vin4", axp803_dcdc2_4_ranges,
+ 76, AXP803_DCDC4_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
+ BIT(3)),
+ AXP_DESC_RANGES(AXP803, DCDC5, "dcdc5", "vin5", axp803_dcdc5_ranges,
+ 69, AXP803_DCDC5_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
+ BIT(4)),
+ AXP_DESC_RANGES(AXP803, DCDC6, "dcdc6", "vin6", axp803_dcdc6_ranges,
+ 72, AXP803_DCDC6_V_OUT, 0x7f, AXP22X_PWR_OUT_CTRL1,
+ BIT(5)),
+ AXP_DESC(AXP803, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
+ AXP22X_ALDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(5)),
+ AXP_DESC(AXP803, ALDO2, "aldo2", "aldoin", 700, 3300, 100,
+ AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(6)),
+ AXP_DESC(AXP803, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
+ AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL3, BIT(7)),
+ AXP_DESC_IO(AXP803, LDO_IO0, "ldo_io0", "ips", 700, 3300, 100,
+ AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07,
+ AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
+ AXP_DESC_IO(AXP803, LDO_IO1, "ldo_io1", "ips", 700, 3300, 100,
+ AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07,
+ AXP22X_IO_ENABLED, AXP22X_IO_DISABLED),
+ AXP_DESC_FIXED(AXP803, RTC_LDO, "rtc_ldo", "ips", 1800),
+ /* secondary switchable output of DCDC1 */
+ AXP_DESC_SW(AXP803, DC1SW, "dc1sw", NULL, AXP22X_PWR_OUT_CTRL2,
+ BIT(7)),
+};
+
+static const struct regmap_range axp803_writeable_ranges[] = {
+ regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
+ regmap_reg_range(AXP20X_DCDC_MODE, AXP22X_BATLOW_THRES1),
+};
+
+static const struct regmap_range axp803_volatile_ranges[] = {
+ regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP20X_PWR_OP_MODE),
+ regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ5_STATE),
+ regmap_reg_range(AXP22X_GPIO_STATE, AXP22X_GPIO_STATE),
+ regmap_reg_range(AXP20X_FG_RES, AXP20X_FG_RES),
+};
+
+static const struct regmap_access_table axp803_writeable_table = {
+ .yes_ranges = axp803_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp803_writeable_ranges),
+};
+
+static const struct regmap_access_table axp803_volatile_table = {
+ .yes_ranges = axp803_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp803_volatile_ranges),
+};
+
+static const struct regmap_config axp803_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .wr_table = &axp803_writeable_table,
+ .volatile_table = &axp803_volatile_table,
+ .max_register = AXP22X_BATLOW_THRES1,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+#define INIT_REGMAP_IRQ(_irq, _off, _bit) \
+ [AXP809_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_bit) }
+
+static const struct regmap_irq axp803_regmap_irqs[] = {
+ INIT_REGMAP_IRQ(PEK_RIS_EDGE, 4, 6),
+ INIT_REGMAP_IRQ(PEK_FAL_EDGE, 4, 5),
+ INIT_REGMAP_IRQ(PEK_SHORT, 4, 4),
+ INIT_REGMAP_IRQ(PEK_LONG, 4, 3),
+ INIT_REGMAP_IRQ(PEK_OVER_OFF, 4, 2),
+ INIT_REGMAP_IRQ(GPIO1_INPUT, 4, 1),
+ INIT_REGMAP_IRQ(GPIO0_INPUT, 4, 0),
+};
+
+static const struct regmap_irq_chip axp803_regmap_irq_chip = {
+ .name = "axp803",
+ .status_base = AXP20X_IRQ1_STATE,
+ .ack_base = AXP20X_IRQ1_STATE,
+ .mask_base = AXP20X_IRQ1_EN,
+ .mask_invert = true,
+ .init_ack_masked = true,
+ .irqs = axp803_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(axp803_regmap_irqs),
+ .num_regs = 6,
+};
+
+static const struct axp_cfg axp803_cfg = {
+ .regulators = axp803_regulators,
+ .nregulators= ARRAY_SIZE(axp803_regulators),
+ .dcdc1_ix = AXP803_DCDC1,
+ .dcdc5_ix = -1,
+ .dc1sw_ix = AXP803_DC1SW,
+ .dc5ldo_ix = -1,
+};
+
+static struct axp20x_dev axp803_dev = {
+ .regmap_cfg = &axp803_regmap_config,
+ .regmap_irq_chip = &axp803_regmap_irq_chip,
+};
+
+static int axp803_rsb_probe(struct sunxi_rsb_device *rdev)
+{
+ return axp_rsb_probe(rdev, &axp803_dev, &axp803_cfg);
+}
+
+static const struct of_device_id axp803_of_match[] = {
+ { .compatible = "x-powers,axp803", .data = (void *) AXP803_ID },
+ { },
+};
+MODULE_DEVICE_TABLE(of, axp803_of_match);
+
+static struct sunxi_rsb_driver axp803_rsb_driver = {
+ .driver = {
+ .name = "axp803-rsb",
+ .of_match_table = of_match_ptr(axp803_of_match),
+ },
+ .probe = axp803_rsb_probe,
+ .remove = axp_rsb_remove,
+};
+module_sunxi_rsb_driver(axp803_rsb_driver);
+
+MODULE_DESCRIPTION("AXP803 RSB driver");
+MODULE_AUTHOR("Jean-Francois Moine <moinejf@free.fr>");
+MODULE_LICENSE("GPL v2");
@@ -20,6 +20,7 @@ enum {
AXP221_ID,
AXP223_ID,
AXP288_ID,
+ AXP803_ID,
AXP806_ID,
AXP809_ID,
NR_AXP20X_VARIANTS,
The X-Powers AXP803 PMIC is close to the AXP809 with more outputs. It is used in some Allwinner boards as the Sinovoip BananaPi M64 and the Pine A64. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> --- not tested --- Documentation/devicetree/bindings/mfd/axp20x.txt | 32 +++- drivers/mfd/axp20x.c | 13 ++ drivers/regulator/Makefile | 3 +- drivers/regulator/axp803.c | 225 +++++++++++++++++++++++ include/linux/mfd/axp20x.h | 1 + 5 files changed, 271 insertions(+), 3 deletions(-) create mode 100644 drivers/regulator/axp803.c