| Message ID | 20161018195605.21145-1-khilman@baylibre.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 18 October 2016 at 21:56, Kevin Hilman <khilman@baylibre.com> wrote: > Initial support for the SD/eMMC controller in the Amlogic S905/GX* > family of SoCs. > > Signed-off-by: Kevin Hilman <khilman@baylibre.com> > --- > Changes from v3: > - better handling of clock error paths > - rename to meson-gx to reflect support for newer SoCs > - has now been tested with SDIO > > .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 33 + Just realize this. You should split the DT doc into a separate patch, such the DT maintainers can ack it. Otherwise this looks good to me! Kind regards Uffe > MAINTAINERS | 1 + > drivers/mmc/host/Kconfig | 10 + > drivers/mmc/host/Makefile | 1 + > drivers/mmc/host/meson-gx.c | 853 +++++++++++++++++++++ > 5 files changed, 898 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt > create mode 100644 drivers/mmc/host/meson-gx.c > > diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt > new file mode 100644 > index 000000000000..a2fa9a1c26ae > --- /dev/null > +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt > @@ -0,0 +1,33 @@ > +Amlogic SD / eMMC controller for S905/GXBB family SoCs > + > +The MMC 5.1 compliant host controller on Amlogic provides the > +interface for SD, eMMC and SDIO devices. > + > +This file documents the properties in addition to those available in > +the MMC core bindings, documented by mmc.txt. > + > +Required properties: > +- compatible : contains one of: > + - "amlogic,meson-gx-mmc" > + - "amlogic,meson-gxbb-mmc" > + - "amlogic,meson-gxl-mmc" > + - "amlogic,meson-gxm-mmc" > +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. > +- clock-names: Should contain the following: > + "core" - Main peripheral bus clock > + "clkin0" - Parent clock of internal mux > + "clkin1" - Other parent clock of internal mux > + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the > + clock rate requested by the MMC core. > + > +Example: > + > + sd_emmc_a: mmc@70000 { > + compatible = "amlogic,meson-gxbb-mmc"; > + reg = <0x0 0x70000 0x0 0x2000>; > + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; > + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; > + clock-names = "core", "clkin0", "clkin1"; > + pinctrl-0 = <&emmc_pins>; > + }; > + > diff --git a/MAINTAINERS b/MAINTAINERS > index 1cd38a7e0064..73e8d64ec28c 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1036,6 +1036,7 @@ F: arch/arm/mach-meson/ > F: arch/arm/boot/dts/meson* > F: arch/arm64/boot/dts/amlogic/ > F: drivers/pinctrl/meson/ > +F: drivers/mmc/host/meson* > N: meson > > ARM/Annapurna Labs ALPINE ARCHITECTURE > diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig > index 5274f503a39a..5cf7ebaf1e8b 100644 > --- a/drivers/mmc/host/Kconfig > +++ b/drivers/mmc/host/Kconfig > @@ -322,6 +322,16 @@ config MMC_SDHCI_IPROC > > If unsure, say N. > > +config MMC_MESON_GX > + tristate "Amlogic S905/GX* SD/MMC Host Controller support" > + depends on ARCH_MESON && MMC > + help > + This selects support for the Amlogic SD/MMC Host Controller > + found on the S905/GX* family of SoCs. This controller is > + MMC 5.1 compliant and supports SD, eMMC and SDIO interfaces. > + > + If you have a controller with this interface, say Y here. > + > config MMC_MOXART > tristate "MOXART SD/MMC Host Controller support" > depends on ARCH_MOXART && MMC > diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile > index e2bdaaf43184..1c4852999ae4 100644 > --- a/drivers/mmc/host/Makefile > +++ b/drivers/mmc/host/Makefile > @@ -53,6 +53,7 @@ obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o > obj-$(CONFIG_MMC_VUB300) += vub300.o > obj-$(CONFIG_MMC_USHC) += ushc.o > obj-$(CONFIG_MMC_WMT) += wmt-sdmmc.o > +obj-$(CONFIG_MMC_MESON_GX) += meson-gx.o > obj-$(CONFIG_MMC_MOXART) += moxart-mmc.o > obj-$(CONFIG_MMC_SUNXI) += sunxi-mmc.o > obj-$(CONFIG_MMC_USDHI6ROL0) += usdhi6rol0.o > diff --git a/drivers/mmc/host/meson-gx.c b/drivers/mmc/host/meson-gx.c > new file mode 100644 > index 000000000000..fd3c40322b2d > --- /dev/null > +++ b/drivers/mmc/host/meson-gx.c > @@ -0,0 +1,853 @@ > +/* > + * Amlogic SD/eMMC driver for the GX/S905 family SoCs > + * > + * Copyright (c) 2016 BayLibre, SAS. > + * Author: Kevin Hilman <khilman@baylibre.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of version 2 of the GNU General Public License as > + * published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, but > + * WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU > + * General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, see <http://www.gnu.org/licenses/>. > + * The full GNU General Public License is included in this distribution > + * in the file called COPYING. > + */ > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/init.h> > +#include <linux/device.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/ioport.h> > +#include <linux/spinlock.h> > +#include <linux/dma-mapping.h> > +#include <linux/mmc/host.h> > +#include <linux/mmc/mmc.h> > +#include <linux/mmc/sdio.h> > +#include <linux/mmc/slot-gpio.h> > +#include <linux/io.h> > +#include <linux/clk.h> > +#include <linux/clk-provider.h> > +#include <linux/regulator/consumer.h> > + > +#define DRIVER_NAME "meson-gxbb-mmc" > + > +#define SD_EMMC_CLOCK 0x0 > +#define CLK_DIV_SHIFT 0 > +#define CLK_DIV_WIDTH 6 > +#define CLK_DIV_MASK 0x3f > +#define CLK_DIV_MAX 63 > +#define CLK_SRC_SHIFT 6 > +#define CLK_SRC_WIDTH 2 > +#define CLK_SRC_MASK 0x3 > +#define CLK_SRC_XTAL 0 /* external crystal */ > +#define CLK_SRC_XTAL_RATE 24000000 > +#define CLK_SRC_PLL 1 /* FCLK_DIV2 */ > +#define CLK_SRC_PLL_RATE 1000000000 > +#define CLK_PHASE_SHIFT 8 > +#define CLK_PHASE_MASK 0x3 > +#define CLK_PHASE_0 0 > +#define CLK_PHASE_90 1 > +#define CLK_PHASE_180 2 > +#define CLK_PHASE_270 3 > +#define CLK_ALWAYS_ON BIT(24) > + > +#define SD_EMMC_DElAY 0x4 > +#define SD_EMMC_ADJUST 0x8 > +#define SD_EMMC_CALOUT 0x10 > +#define SD_EMMC_START 0x40 > +#define START_DESC_INIT BIT(0) > +#define START_DESC_BUSY BIT(1) > +#define START_DESC_ADDR_SHIFT 2 > +#define START_DESC_ADDR_MASK (~0x3) > + > +#define SD_EMMC_CFG 0x44 > +#define CFG_BUS_WIDTH_SHIFT 0 > +#define CFG_BUS_WIDTH_MASK 0x3 > +#define CFG_BUS_WIDTH_1 0x0 > +#define CFG_BUS_WIDTH_4 0x1 > +#define CFG_BUS_WIDTH_8 0x2 > +#define CFG_DDR BIT(2) > +#define CFG_BLK_LEN_SHIFT 4 > +#define CFG_BLK_LEN_MASK 0xf > +#define CFG_RESP_TIMEOUT_SHIFT 8 > +#define CFG_RESP_TIMEOUT_MASK 0xf > +#define CFG_RC_CC_SHIFT 12 > +#define CFG_RC_CC_MASK 0xf > +#define CFG_STOP_CLOCK BIT(22) > +#define CFG_CLK_ALWAYS_ON BIT(18) > +#define CFG_AUTO_CLK BIT(23) > + > +#define SD_EMMC_STATUS 0x48 > +#define STATUS_BUSY BIT(31) > + > +#define SD_EMMC_IRQ_EN 0x4c > +#define IRQ_EN_MASK 0x3fff > +#define IRQ_RXD_ERR_SHIFT 0 > +#define IRQ_RXD_ERR_MASK 0xff > +#define IRQ_TXD_ERR BIT(8) > +#define IRQ_DESC_ERR BIT(9) > +#define IRQ_RESP_ERR BIT(10) > +#define IRQ_RESP_TIMEOUT BIT(11) > +#define IRQ_DESC_TIMEOUT BIT(12) > +#define IRQ_END_OF_CHAIN BIT(13) > +#define IRQ_RESP_STATUS BIT(14) > +#define IRQ_SDIO BIT(15) > + > +#define SD_EMMC_CMD_CFG 0x50 > +#define SD_EMMC_CMD_ARG 0x54 > +#define SD_EMMC_CMD_DAT 0x58 > +#define SD_EMMC_CMD_RSP 0x5c > +#define SD_EMMC_CMD_RSP1 0x60 > +#define SD_EMMC_CMD_RSP2 0x64 > +#define SD_EMMC_CMD_RSP3 0x68 > + > +#define SD_EMMC_RXD 0x94 > +#define SD_EMMC_TXD 0x94 > +#define SD_EMMC_LAST_REG SD_EMMC_TXD > + > +#define SD_EMMC_CFG_BLK_SIZE 512 /* internal buffer max: 512 bytes */ > +#define SD_EMMC_CFG_RESP_TIMEOUT 256 /* in clock cycles */ > +#define SD_EMMC_CFG_CMD_GAP 16 /* in clock cycles */ > +#define MUX_CLK_NUM_PARENTS 2 > + > +struct meson_host { > + struct device *dev; > + struct mmc_host *mmc; > + struct mmc_request *mrq; > + struct mmc_command *cmd; > + > + spinlock_t lock; > + void __iomem *regs; > + int irq; > + u32 ocr_mask; > + struct clk *core_clk; > + struct clk_mux mux; > + struct clk *mux_clk; > + struct clk *mux_parent[MUX_CLK_NUM_PARENTS]; > + unsigned long mux_parent_rate[MUX_CLK_NUM_PARENTS]; > + > + struct clk_divider cfg_div; > + struct clk *cfg_div_clk; > + > + unsigned int bounce_buf_size; > + void *bounce_buf; > + dma_addr_t bounce_dma_addr; > + > + bool vqmmc_enabled; > +}; > + > +struct sd_emmc_desc { > + u32 cmd_cfg; > + u32 cmd_arg; > + u32 cmd_data; > + u32 cmd_resp; > +}; > +#define CMD_CFG_LENGTH_SHIFT 0 > +#define CMD_CFG_LENGTH_MASK 0x1ff > +#define CMD_CFG_BLOCK_MODE BIT(9) > +#define CMD_CFG_R1B BIT(10) > +#define CMD_CFG_END_OF_CHAIN BIT(11) > +#define CMD_CFG_TIMEOUT_SHIFT 12 > +#define CMD_CFG_TIMEOUT_MASK 0xf > +#define CMD_CFG_NO_RESP BIT(16) > +#define CMD_CFG_NO_CMD BIT(17) > +#define CMD_CFG_DATA_IO BIT(18) > +#define CMD_CFG_DATA_WR BIT(19) > +#define CMD_CFG_RESP_NOCRC BIT(20) > +#define CMD_CFG_RESP_128 BIT(21) > +#define CMD_CFG_RESP_NUM BIT(22) > +#define CMD_CFG_DATA_NUM BIT(23) > +#define CMD_CFG_CMD_INDEX_SHIFT 24 > +#define CMD_CFG_CMD_INDEX_MASK 0x3f > +#define CMD_CFG_ERROR BIT(30) > +#define CMD_CFG_OWNER BIT(31) > + > +#define CMD_DATA_MASK (~0x3) > +#define CMD_DATA_BIG_ENDIAN BIT(1) > +#define CMD_DATA_SRAM BIT(0) > +#define CMD_RESP_MASK (~0x1) > +#define CMD_RESP_SRAM BIT(0) > + > +static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate) > +{ > + struct mmc_host *mmc = host->mmc; > + int ret = 0; > + u32 cfg; > + > + if (clk_rate) { > + if (WARN_ON(clk_rate > mmc->f_max)) > + clk_rate = mmc->f_max; > + else if (WARN_ON(clk_rate < mmc->f_min)) > + clk_rate = mmc->f_min; > + } > + > + if (clk_rate == mmc->actual_clock) > + return 0; > + > + /* stop clock */ > + cfg = readl(host->regs + SD_EMMC_CFG); > + if (!(cfg & CFG_STOP_CLOCK)) { > + cfg |= CFG_STOP_CLOCK; > + writel(cfg, host->regs + SD_EMMC_CFG); > + } > + > + dev_dbg(host->dev, "change clock rate %u -> %lu\n", > + mmc->actual_clock, clk_rate); > + > + if (clk_rate == 0) { > + mmc->actual_clock = 0; > + return 0; > + } > + > + ret = clk_set_rate(host->cfg_div_clk, clk_rate); > + if (ret) > + dev_warn(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n", > + clk_rate, ret); > + else if (clk_rate && clk_rate != clk_get_rate(host->cfg_div_clk)) > + dev_warn(host->dev, "divider requested rate %lu != actual rate %lu: ret=%d\n", > + clk_rate, clk_get_rate(host->cfg_div_clk), ret); > + else > + mmc->actual_clock = clk_rate; > + > + /* (re)start clock, if non-zero */ > + if (!ret && clk_rate) { > + cfg = readl(host->regs + SD_EMMC_CFG); > + cfg &= ~CFG_STOP_CLOCK; > + writel(cfg, host->regs + SD_EMMC_CFG); > + } > + > + return ret; > +} > + > +/* > + * The SD/eMMC IP block has an internal mux and divider used for > + * generating the MMC clock. Use the clock framework to create and > + * manage these clocks. > + */ > +static int meson_mmc_clk_init(struct meson_host *host) > +{ > + struct clk_init_data init; > + char clk_name[32]; > + int i, ret = 0; > + const char *mux_parent_names[MUX_CLK_NUM_PARENTS]; > + unsigned int mux_parent_count = 0; > + const char *clk_div_parents[1]; > + unsigned int f_min = UINT_MAX; > + u32 clk_reg, cfg; > + > + /* get the mux parents */ > + for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) { > + char name[16]; > + > + snprintf(name, sizeof(name), "clkin%d", i); > + host->mux_parent[i] = devm_clk_get(host->dev, name); > + if (IS_ERR(host->mux_parent[i])) { > + ret = PTR_ERR(host->mux_parent[i]); > + if (PTR_ERR(host->mux_parent[i]) != -EPROBE_DEFER) > + dev_err(host->dev, "Missing clock %s\n", name); > + host->mux_parent[i] = NULL; > + return ret; > + } > + > + host->mux_parent_rate[i] = clk_get_rate(host->mux_parent[i]); > + mux_parent_names[i] = __clk_get_name(host->mux_parent[i]); > + mux_parent_count++; > + if (host->mux_parent_rate[i] < f_min) > + f_min = host->mux_parent_rate[i]; > + } > + > + /* cacluate f_min based on input clocks, and max divider value */ > + if (f_min != UINT_MAX) > + f_min = DIV_ROUND_UP(CLK_SRC_XTAL_RATE, CLK_DIV_MAX); > + else > + f_min = 4000000; /* default min: 400 MHz */ > + host->mmc->f_min = f_min; > + > + /* create the mux */ > + snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev)); > + init.name = clk_name; > + init.ops = &clk_mux_ops; > + init.flags = 0; > + init.parent_names = mux_parent_names; > + init.num_parents = mux_parent_count; > + > + host->mux.reg = host->regs + SD_EMMC_CLOCK; > + host->mux.shift = CLK_SRC_SHIFT; > + host->mux.mask = CLK_SRC_MASK; > + host->mux.flags = 0; > + host->mux.table = NULL; > + host->mux.hw.init = &init; > + > + host->mux_clk = devm_clk_register(host->dev, &host->mux.hw); > + if (WARN_ON(IS_ERR(host->mux_clk))) > + return PTR_ERR(host->mux_clk); > + > + /* create the divider */ > + snprintf(clk_name, sizeof(clk_name), "%s#div", dev_name(host->dev)); > + init.name = devm_kstrdup(host->dev, clk_name, GFP_KERNEL); > + init.ops = &clk_divider_ops; > + init.flags = CLK_SET_RATE_PARENT; > + clk_div_parents[0] = __clk_get_name(host->mux_clk); > + init.parent_names = clk_div_parents; > + init.num_parents = ARRAY_SIZE(clk_div_parents); > + > + host->cfg_div.reg = host->regs + SD_EMMC_CLOCK; > + host->cfg_div.shift = CLK_DIV_SHIFT; > + host->cfg_div.width = CLK_DIV_WIDTH; > + host->cfg_div.hw.init = &init; > + host->cfg_div.flags = CLK_DIVIDER_ONE_BASED | > + CLK_DIVIDER_ROUND_CLOSEST | CLK_DIVIDER_ALLOW_ZERO; > + > + host->cfg_div_clk = devm_clk_register(host->dev, &host->cfg_div.hw); > + if (WARN_ON(PTR_ERR_OR_ZERO(host->cfg_div_clk))) > + return PTR_ERR(host->cfg_div_clk); > + > + /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */ > + clk_reg = 0; > + clk_reg |= CLK_PHASE_180 << CLK_PHASE_SHIFT; > + clk_reg |= CLK_SRC_XTAL << CLK_SRC_SHIFT; > + clk_reg |= CLK_DIV_MAX << CLK_DIV_SHIFT; > + clk_reg &= ~CLK_ALWAYS_ON; > + writel(clk_reg, host->regs + SD_EMMC_CLOCK); > + > + /* Ensure clock starts in "auto" mode, not "always on" */ > + cfg = readl(host->regs + SD_EMMC_CFG); > + cfg &= ~CFG_CLK_ALWAYS_ON; > + cfg |= CFG_AUTO_CLK; > + writel(cfg, host->regs + SD_EMMC_CFG); > + > + ret = clk_prepare_enable(host->cfg_div_clk); > + if (!ret) > + ret = meson_mmc_clk_set(host, f_min); > + > + if (!ret) > + clk_disable_unprepare(host->cfg_div_clk); > + > + return ret; > +} > + > +static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) > +{ > + struct meson_host *host = mmc_priv(mmc); > + u32 bus_width; > + u32 val, orig; > + > + /* > + * GPIO regulator, only controls switching between 1v8 and > + * 3v3, doesn't support MMC_POWER_OFF, MMC_POWER_ON. > + */ > + switch (ios->power_mode) { > + case MMC_POWER_OFF: > + if (!IS_ERR(mmc->supply.vmmc)) > + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); > + > + if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) { > + regulator_disable(mmc->supply.vqmmc); > + host->vqmmc_enabled = false; > + } > + > + break; > + > + case MMC_POWER_UP: > + if (!IS_ERR(mmc->supply.vmmc)) > + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd); > + break; > + > + case MMC_POWER_ON: > + if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) { > + int ret = regulator_enable(mmc->supply.vqmmc); > + > + if (ret < 0) > + dev_err(mmc_dev(mmc), > + "failed to enable vqmmc regulator\n"); > + else > + host->vqmmc_enabled = true; > + } > + > + break; > + } > + > + > + meson_mmc_clk_set(host, ios->clock); > + > + /* Bus width */ > + val = readl(host->regs + SD_EMMC_CFG); > + switch (ios->bus_width) { > + case MMC_BUS_WIDTH_1: > + bus_width = CFG_BUS_WIDTH_1; > + break; > + case MMC_BUS_WIDTH_4: > + bus_width = CFG_BUS_WIDTH_4; > + break; > + case MMC_BUS_WIDTH_8: > + bus_width = CFG_BUS_WIDTH_8; > + break; > + default: > + dev_err(host->dev, "Invalid ios->bus_width: %u. Setting to 4.\n", > + ios->bus_width); > + bus_width = CFG_BUS_WIDTH_4; > + return; > + } > + > + val = readl(host->regs + SD_EMMC_CFG); > + orig = val; > + > + val &= ~(CFG_BUS_WIDTH_MASK << CFG_BUS_WIDTH_SHIFT); > + val |= bus_width << CFG_BUS_WIDTH_SHIFT; > + > + val &= ~(CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); > + val |= ilog2(SD_EMMC_CFG_BLK_SIZE) << CFG_BLK_LEN_SHIFT; > + > + val &= ~(CFG_RESP_TIMEOUT_MASK << CFG_RESP_TIMEOUT_SHIFT); > + val |= ilog2(SD_EMMC_CFG_RESP_TIMEOUT) << CFG_RESP_TIMEOUT_SHIFT; > + > + val &= ~(CFG_RC_CC_MASK << CFG_RC_CC_SHIFT); > + val |= ilog2(SD_EMMC_CFG_CMD_GAP) << CFG_RC_CC_SHIFT; > + > + writel(val, host->regs + SD_EMMC_CFG); > + > + if (val != orig) > + dev_dbg(host->dev, "%s: SD_EMMC_CFG: 0x%08x -> 0x%08x\n", > + __func__, orig, val); > +} > + > +static int meson_mmc_request_done(struct mmc_host *mmc, struct mmc_request *mrq) > +{ > + struct meson_host *host = mmc_priv(mmc); > + > + WARN_ON(host->mrq != mrq); > + > + host->mrq = NULL; > + host->cmd = NULL; > + mmc_request_done(host->mmc, mrq); > + > + return 0; > +} > + > +static void meson_mmc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd) > +{ > + struct meson_host *host = mmc_priv(mmc); > + struct sd_emmc_desc *desc, desc_tmp; > + u32 cfg; > + u8 blk_len, cmd_cfg_timeout; > + unsigned int xfer_bytes = 0; > + > + /* Setup descriptors */ > + dma_rmb(); > + desc = &desc_tmp; > + memset(desc, 0, sizeof(struct sd_emmc_desc)); > + > + desc->cmd_cfg |= (cmd->opcode & CMD_CFG_CMD_INDEX_MASK) << > + CMD_CFG_CMD_INDEX_SHIFT; > + desc->cmd_cfg |= CMD_CFG_OWNER; /* owned by CPU */ > + desc->cmd_arg = cmd->arg; > + > + /* Response */ > + if (cmd->flags & MMC_RSP_PRESENT) { > + desc->cmd_cfg &= ~CMD_CFG_NO_RESP; > + if (cmd->flags & MMC_RSP_136) > + desc->cmd_cfg |= CMD_CFG_RESP_128; > + desc->cmd_cfg |= CMD_CFG_RESP_NUM; > + desc->cmd_resp = 0; > + > + if (!(cmd->flags & MMC_RSP_CRC)) > + desc->cmd_cfg |= CMD_CFG_RESP_NOCRC; > + > + if (cmd->flags & MMC_RSP_BUSY) > + desc->cmd_cfg |= CMD_CFG_R1B; > + } else { > + desc->cmd_cfg |= CMD_CFG_NO_RESP; > + } > + > + /* data? */ > + if (cmd->data) { > + desc->cmd_cfg |= CMD_CFG_DATA_IO; > + if (cmd->data->blocks > 1) { > + desc->cmd_cfg |= CMD_CFG_BLOCK_MODE; > + desc->cmd_cfg |= > + (cmd->data->blocks & CMD_CFG_LENGTH_MASK) << > + CMD_CFG_LENGTH_SHIFT; > + > + /* check if block-size matches, if not update */ > + cfg = readl(host->regs + SD_EMMC_CFG); > + blk_len = cfg & (CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); > + blk_len >>= CFG_BLK_LEN_SHIFT; > + if (blk_len != ilog2(cmd->data->blksz)) { > + dev_warn(host->dev, "%s: update blk_len %d -> %d\n", > + __func__, blk_len, > + ilog2(cmd->data->blksz)); > + blk_len = ilog2(cmd->data->blksz); > + cfg &= ~(CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); > + cfg |= blk_len << CFG_BLK_LEN_SHIFT; > + writel(cfg, host->regs + SD_EMMC_CFG); > + } > + } else { > + desc->cmd_cfg &= ~CMD_CFG_BLOCK_MODE; > + desc->cmd_cfg |= > + (cmd->data->blksz & CMD_CFG_LENGTH_MASK) << > + CMD_CFG_LENGTH_SHIFT; > + } > + > + cmd->data->bytes_xfered = 0; > + xfer_bytes = cmd->data->blksz * cmd->data->blocks; > + if (cmd->data->flags & MMC_DATA_WRITE) { > + desc->cmd_cfg |= CMD_CFG_DATA_WR; > + WARN_ON(xfer_bytes > host->bounce_buf_size); > + sg_copy_to_buffer(cmd->data->sg, cmd->data->sg_len, > + host->bounce_buf, xfer_bytes); > + cmd->data->bytes_xfered = xfer_bytes; > + dma_wmb(); > + } else { > + desc->cmd_cfg &= ~CMD_CFG_DATA_WR; > + } > + > + if (xfer_bytes > 0) { > + desc->cmd_cfg &= ~CMD_CFG_DATA_NUM; > + desc->cmd_data = host->bounce_dma_addr & CMD_DATA_MASK; > + } else { > + /* write data to data_addr */ > + desc->cmd_cfg |= CMD_CFG_DATA_NUM; > + desc->cmd_data = 0; > + } > + > + cmd_cfg_timeout = 12; > + } else { > + desc->cmd_cfg &= ~CMD_CFG_DATA_IO; > + cmd_cfg_timeout = 10; > + } > + desc->cmd_cfg |= (cmd_cfg_timeout & CMD_CFG_TIMEOUT_MASK) << > + CMD_CFG_TIMEOUT_SHIFT; > + > + host->cmd = cmd; > + > + /* Last descriptor */ > + desc->cmd_cfg |= CMD_CFG_END_OF_CHAIN; > + writel(desc->cmd_cfg, host->regs + SD_EMMC_CMD_CFG); > + writel(desc->cmd_data, host->regs + SD_EMMC_CMD_DAT); > + writel(desc->cmd_resp, host->regs + SD_EMMC_CMD_RSP); > + wmb(); /* ensure descriptor is written before kicked */ > + writel(desc->cmd_arg, host->regs + SD_EMMC_CMD_ARG); > +} > + > +static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) > +{ > + struct meson_host *host = mmc_priv(mmc); > + > + WARN_ON(host->mrq != NULL); > + > + /* Stop execution */ > + writel(0, host->regs + SD_EMMC_START); > + > + /* clear, ack, enable all interrupts */ > + writel(0, host->regs + SD_EMMC_IRQ_EN); > + writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); > + writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN); > + > + host->mrq = mrq; > + > + if (mrq->sbc) > + meson_mmc_start_cmd(mmc, mrq->sbc); > + else > + meson_mmc_start_cmd(mmc, mrq->cmd); > +} > + > +static int meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd) > +{ > + struct meson_host *host = mmc_priv(mmc); > + > + if (cmd->flags & MMC_RSP_136) { > + cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP3); > + cmd->resp[1] = readl(host->regs + SD_EMMC_CMD_RSP2); > + cmd->resp[2] = readl(host->regs + SD_EMMC_CMD_RSP1); > + cmd->resp[3] = readl(host->regs + SD_EMMC_CMD_RSP); > + } else if (cmd->flags & MMC_RSP_PRESENT) { > + cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP); > + } > + > + return 0; > +} > + > +static irqreturn_t meson_mmc_irq(int irq, void *dev_id) > +{ > + struct meson_host *host = dev_id; > + struct mmc_request *mrq; > + struct mmc_command *cmd = host->cmd; > + u32 irq_en, status, raw_status; > + irqreturn_t ret = IRQ_HANDLED; > + > + if (WARN_ON(!host)) > + return IRQ_NONE; > + > + mrq = host->mrq; > + > + if (WARN_ON(!mrq)) > + return IRQ_NONE; > + > + if (WARN_ON(!cmd)) > + return IRQ_NONE; > + > + spin_lock(&host->lock); > + irq_en = readl(host->regs + SD_EMMC_IRQ_EN); > + raw_status = readl(host->regs + SD_EMMC_STATUS); > + status = raw_status & irq_en; > + > + if (!status) { > + dev_warn(host->dev, "Spurious IRQ! status=0x%08x, irq_en=0x%08x\n", > + raw_status, irq_en); > + ret = IRQ_NONE; > + goto out; > + } > + > + cmd->error = 0; > + if (status & IRQ_RXD_ERR_MASK) { > + dev_dbg(host->dev, "Unhandled IRQ: RXD error\n"); > + cmd->error = -EILSEQ; > + } > + if (status & IRQ_TXD_ERR) { > + dev_dbg(host->dev, "Unhandled IRQ: TXD error\n"); > + cmd->error = -EILSEQ; > + } > + if (status & IRQ_DESC_ERR) > + dev_dbg(host->dev, "Unhandled IRQ: Descriptor error\n"); > + if (status & IRQ_RESP_ERR) { > + dev_dbg(host->dev, "Unhandled IRQ: Response error\n"); > + cmd->error = -EILSEQ; > + } > + if (status & IRQ_RESP_TIMEOUT) { > + dev_dbg(host->dev, "Unhandled IRQ: Response timeout\n"); > + cmd->error = -ETIMEDOUT; > + } > + if (status & IRQ_DESC_TIMEOUT) { > + dev_dbg(host->dev, "Unhandled IRQ: Descriptor timeout\n"); > + cmd->error = -ETIMEDOUT; > + } > + if (status & IRQ_SDIO) > + dev_dbg(host->dev, "Unhandled IRQ: SDIO.\n"); > + > + if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) > + ret = IRQ_WAKE_THREAD; > + else { > + dev_warn(host->dev, "Unknown IRQ! status=0x%04x: MMC CMD%u arg=0x%08x flags=0x%08x stop=%d\n", > + status, cmd->opcode, cmd->arg, > + cmd->flags, mrq->stop ? 1 : 0); > + if (cmd->data) { > + struct mmc_data *data = cmd->data; > + > + dev_warn(host->dev, "\tblksz %u blocks %u flags 0x%08x (%s%s)", > + data->blksz, data->blocks, data->flags, > + data->flags & MMC_DATA_WRITE ? "write" : "", > + data->flags & MMC_DATA_READ ? "read" : ""); > + } > + } > + > +out: > + /* ack all (enabled) interrupts */ > + writel(status, host->regs + SD_EMMC_STATUS); > + > + if (ret == IRQ_HANDLED) { > + meson_mmc_read_resp(host->mmc, cmd); > + meson_mmc_request_done(host->mmc, cmd->mrq); > + } > + > + spin_unlock(&host->lock); > + return ret; > +} > + > +static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id) > +{ > + struct meson_host *host = dev_id; > + struct mmc_request *mrq = host->mrq; > + struct mmc_command *cmd = host->cmd; > + struct mmc_data *data; > + unsigned int xfer_bytes; > + int ret = IRQ_HANDLED; > + > + if (WARN_ON(!mrq)) > + ret = IRQ_NONE; > + > + if (WARN_ON(!cmd)) > + ret = IRQ_NONE; > + > + data = cmd->data; > + if (data) { > + xfer_bytes = data->blksz * data->blocks; > + if (data->flags & MMC_DATA_READ) { > + WARN_ON(xfer_bytes > host->bounce_buf_size); > + sg_copy_from_buffer(data->sg, data->sg_len, > + host->bounce_buf, xfer_bytes); > + data->bytes_xfered = xfer_bytes; > + } > + } > + > + meson_mmc_read_resp(host->mmc, cmd); > + if (!data || !data->stop || mrq->sbc) > + meson_mmc_request_done(host->mmc, mrq); > + else > + meson_mmc_start_cmd(host->mmc, data->stop); > + > + return ret; > +} > + > +/* > + * NOTE: we only need this until the GPIO/pinctrl driver can handle > + * interrupts. For now, the MMC core will use this for polling. > + */ > +static int meson_mmc_get_cd(struct mmc_host *mmc) > +{ > + int status = mmc_gpio_get_cd(mmc); > + > + if (status == -ENOSYS) > + return 1; /* assume present */ > + > + return status; > +} > + > +static const struct mmc_host_ops meson_mmc_ops = { > + .request = meson_mmc_request, > + .set_ios = meson_mmc_set_ios, > + .get_cd = meson_mmc_get_cd, > +}; > + > +static int meson_mmc_probe(struct platform_device *pdev) > +{ > + struct resource *res; > + struct meson_host *host; > + struct mmc_host *mmc; > + int ret; > + > + mmc = mmc_alloc_host(sizeof(struct meson_host), &pdev->dev); > + if (!mmc) > + return -ENOMEM; > + host = mmc_priv(mmc); > + host->mmc = mmc; > + host->dev = &pdev->dev; > + dev_set_drvdata(&pdev->dev, host); > + > + spin_lock_init(&host->lock); > + > + /* Get regulators and the supported OCR mask */ > + host->vqmmc_enabled = false; > + ret = mmc_regulator_get_supply(mmc); > + if (ret == -EPROBE_DEFER) > + goto free_host; > + > + ret = mmc_of_parse(mmc); > + if (ret) { > + dev_warn(&pdev->dev, "error parsing DT: %d\n", ret); > + goto free_host; > + } > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + host->regs = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(host->regs)) { > + ret = PTR_ERR(host->regs); > + goto free_host; > + } > + > + host->irq = platform_get_irq(pdev, 0); > + if (host->irq == 0) { > + dev_err(&pdev->dev, "failed to get interrupt resource.\n"); > + ret = -EINVAL; > + goto free_host; > + } > + > + host->core_clk = devm_clk_get(&pdev->dev, "core"); > + if (IS_ERR(host->core_clk)) { > + ret = PTR_ERR(host->core_clk); > + goto free_host; > + } > + > + ret = clk_prepare_enable(host->core_clk); > + if (ret) > + goto free_host; > + > + ret = meson_mmc_clk_init(host); > + if (ret) > + goto free_host; > + > + /* Stop execution */ > + writel(0, host->regs + SD_EMMC_START); > + > + /* clear, ack, enable all interrupts */ > + writel(0, host->regs + SD_EMMC_IRQ_EN); > + writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); > + > + ret = devm_request_threaded_irq(&pdev->dev, host->irq, > + meson_mmc_irq, meson_mmc_irq_thread, > + IRQF_SHARED, DRIVER_NAME, host); > + if (ret) > + goto free_host; > + > + /* data bounce buffer */ > + host->bounce_buf_size = SZ_512K; > + host->bounce_buf = > + dma_alloc_coherent(host->dev, host->bounce_buf_size, > + &host->bounce_dma_addr, GFP_KERNEL); > + if (host->bounce_buf == NULL) { > + dev_err(host->dev, "Unable to map allocate DMA bounce buffer.\n"); > + ret = -ENOMEM; > + goto free_host; > + } > + > + mmc->ops = &meson_mmc_ops; > + mmc_add_host(mmc); > + > + return 0; > + > +free_host: > + clk_disable_unprepare(host->cfg_div_clk); > + clk_disable_unprepare(host->core_clk); > + mmc_free_host(mmc); > + return ret; > +} > + > +static int meson_mmc_remove(struct platform_device *pdev) > +{ > + struct meson_host *host = dev_get_drvdata(&pdev->dev); > + > + if (WARN_ON(!host)) > + return 0; > + > + if (host->bounce_buf) > + dma_free_coherent(host->dev, host->bounce_buf_size, > + host->bounce_buf, host->bounce_dma_addr); > + > + clk_disable_unprepare(host->cfg_div_clk); > + clk_disable_unprepare(host->core_clk); > + > + mmc_free_host(host->mmc); > + return 0; > +} > + > +static const struct of_device_id meson_mmc_of_match[] = { > + { .compatible = "amlogic,meson-gx-mmc", }, > + { .compatible = "amlogic,meson-gxbb-mmc", }, > + { .compatible = "amlogic,meson-gxl-mmc", }, > + { .compatible = "amlogic,meson-gxm-mmc", }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, meson_mmc_of_match); > + > +static struct platform_driver meson_mmc_driver = { > + .probe = meson_mmc_probe, > + .remove = meson_mmc_remove, > + .driver = { > + .name = DRIVER_NAME, > + .of_match_table = of_match_ptr(meson_mmc_of_match), > + }, > +}; > + > +module_platform_driver(meson_mmc_driver); > + > +MODULE_ALIAS("platform:" DRIVER_NAME); > +MODULE_DESCRIPTION("Amlogic S905/GXBB SD/eMMC driver"); > +MODULE_AUTHOR("Kevin Hilman <khilman@baylibre.com>"); > +MODULE_LICENSE("GPL v2"); > + > -- > 2.9.3 >
Ulf Hansson <ulf.hansson@linaro.org> writes: > On 18 October 2016 at 21:56, Kevin Hilman <khilman@baylibre.com> wrote: >> Initial support for the SD/eMMC controller in the Amlogic S905/GX* >> family of SoCs. >> >> Signed-off-by: Kevin Hilman <khilman@baylibre.com> >> --- >> Changes from v3: >> - better handling of clock error paths >> - rename to meson-gx to reflect support for newer SoCs >> - has now been tested with SDIO >> >> .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 33 + > > Just realize this. You should split the DT doc into a separate patch, > such the DT maintainers can ack it. OK, I separated out the binding and sent a v5. > Otherwise this looks good to me! Thanks for the review! Kevin
Hello Kevin, On Tue, Oct 18, 2016 at 4:56 PM, Kevin Hilman <khilman@baylibre.com> wrote: > Initial support for the SD/eMMC controller in the Amlogic S905/GX* > family of SoCs. > > Signed-off-by: Kevin Hilman <khilman@baylibre.com> [snip] > + > +MODULE_ALIAS("platform:" DRIVER_NAME); Why is this module alias needed? I thought that the Amlogic was a DT-only platform and so devices will always be registered from OF (and the OF modalias used). I've seen platform module aliases in other Meson drivers too (i.e: meson-rng and meson-pwm), so the same question applies to those. Best regards, Javier
Javier Martinez Canillas <javier@dowhile0.org> writes: > Hello Kevin, > > On Tue, Oct 18, 2016 at 4:56 PM, Kevin Hilman <khilman@baylibre.com> wrote: >> Initial support for the SD/eMMC controller in the Amlogic S905/GX* >> family of SoCs. >> >> Signed-off-by: Kevin Hilman <khilman@baylibre.com> > > [snip] > >> + >> +MODULE_ALIAS("platform:" DRIVER_NAME); > > Why is this module alias needed? I thought that the Amlogic was a > DT-only platform and so devices will always be registered from OF (and > the OF modalias used). You're right, I probably copy/pasted it from another driver. Testing without it also made me realize that the module filename (meson_gx) isn't really useful when listed in lsmod, so I 'll respin to have mmc in the filename so the module name also shows mmc. Kevin
diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt new file mode 100644 index 000000000000..a2fa9a1c26ae --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt @@ -0,0 +1,33 @@ +Amlogic SD / eMMC controller for S905/GXBB family SoCs + +The MMC 5.1 compliant host controller on Amlogic provides the +interface for SD, eMMC and SDIO devices. + +This file documents the properties in addition to those available in +the MMC core bindings, documented by mmc.txt. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gx-mmc" + - "amlogic,meson-gxbb-mmc" + - "amlogic,meson-gxl-mmc" + - "amlogic,meson-gxm-mmc" +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "core" - Main peripheral bus clock + "clkin0" - Parent clock of internal mux + "clkin1" - Other parent clock of internal mux + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the + clock rate requested by the MMC core. + +Example: + + sd_emmc_a: mmc@70000 { + compatible = "amlogic,meson-gxbb-mmc"; + reg = <0x0 0x70000 0x0 0x2000>; + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + pinctrl-0 = <&emmc_pins>; + }; + diff --git a/MAINTAINERS b/MAINTAINERS index 1cd38a7e0064..73e8d64ec28c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1036,6 +1036,7 @@ F: arch/arm/mach-meson/ F: arch/arm/boot/dts/meson* F: arch/arm64/boot/dts/amlogic/ F: drivers/pinctrl/meson/ +F: drivers/mmc/host/meson* N: meson ARM/Annapurna Labs ALPINE ARCHITECTURE diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 5274f503a39a..5cf7ebaf1e8b 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -322,6 +322,16 @@ config MMC_SDHCI_IPROC If unsure, say N. +config MMC_MESON_GX + tristate "Amlogic S905/GX* SD/MMC Host Controller support" + depends on ARCH_MESON && MMC + help + This selects support for the Amlogic SD/MMC Host Controller + found on the S905/GX* family of SoCs. This controller is + MMC 5.1 compliant and supports SD, eMMC and SDIO interfaces. + + If you have a controller with this interface, say Y here. + config MMC_MOXART tristate "MOXART SD/MMC Host Controller support" depends on ARCH_MOXART && MMC diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index e2bdaaf43184..1c4852999ae4 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -53,6 +53,7 @@ obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o obj-$(CONFIG_MMC_VUB300) += vub300.o obj-$(CONFIG_MMC_USHC) += ushc.o obj-$(CONFIG_MMC_WMT) += wmt-sdmmc.o +obj-$(CONFIG_MMC_MESON_GX) += meson-gx.o obj-$(CONFIG_MMC_MOXART) += moxart-mmc.o obj-$(CONFIG_MMC_SUNXI) += sunxi-mmc.o obj-$(CONFIG_MMC_USDHI6ROL0) += usdhi6rol0.o diff --git a/drivers/mmc/host/meson-gx.c b/drivers/mmc/host/meson-gx.c new file mode 100644 index 000000000000..fd3c40322b2d --- /dev/null +++ b/drivers/mmc/host/meson-gx.c @@ -0,0 +1,853 @@ +/* + * Amlogic SD/eMMC driver for the GX/S905 family SoCs + * + * Copyright (c) 2016 BayLibre, SAS. + * Author: Kevin Hilman <khilman@baylibre.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see <http://www.gnu.org/licenses/>. + * The full GNU General Public License is included in this distribution + * in the file called COPYING. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/ioport.h> +#include <linux/spinlock.h> +#include <linux/dma-mapping.h> +#include <linux/mmc/host.h> +#include <linux/mmc/mmc.h> +#include <linux/mmc/sdio.h> +#include <linux/mmc/slot-gpio.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/regulator/consumer.h> + +#define DRIVER_NAME "meson-gxbb-mmc" + +#define SD_EMMC_CLOCK 0x0 +#define CLK_DIV_SHIFT 0 +#define CLK_DIV_WIDTH 6 +#define CLK_DIV_MASK 0x3f +#define CLK_DIV_MAX 63 +#define CLK_SRC_SHIFT 6 +#define CLK_SRC_WIDTH 2 +#define CLK_SRC_MASK 0x3 +#define CLK_SRC_XTAL 0 /* external crystal */ +#define CLK_SRC_XTAL_RATE 24000000 +#define CLK_SRC_PLL 1 /* FCLK_DIV2 */ +#define CLK_SRC_PLL_RATE 1000000000 +#define CLK_PHASE_SHIFT 8 +#define CLK_PHASE_MASK 0x3 +#define CLK_PHASE_0 0 +#define CLK_PHASE_90 1 +#define CLK_PHASE_180 2 +#define CLK_PHASE_270 3 +#define CLK_ALWAYS_ON BIT(24) + +#define SD_EMMC_DElAY 0x4 +#define SD_EMMC_ADJUST 0x8 +#define SD_EMMC_CALOUT 0x10 +#define SD_EMMC_START 0x40 +#define START_DESC_INIT BIT(0) +#define START_DESC_BUSY BIT(1) +#define START_DESC_ADDR_SHIFT 2 +#define START_DESC_ADDR_MASK (~0x3) + +#define SD_EMMC_CFG 0x44 +#define CFG_BUS_WIDTH_SHIFT 0 +#define CFG_BUS_WIDTH_MASK 0x3 +#define CFG_BUS_WIDTH_1 0x0 +#define CFG_BUS_WIDTH_4 0x1 +#define CFG_BUS_WIDTH_8 0x2 +#define CFG_DDR BIT(2) +#define CFG_BLK_LEN_SHIFT 4 +#define CFG_BLK_LEN_MASK 0xf +#define CFG_RESP_TIMEOUT_SHIFT 8 +#define CFG_RESP_TIMEOUT_MASK 0xf +#define CFG_RC_CC_SHIFT 12 +#define CFG_RC_CC_MASK 0xf +#define CFG_STOP_CLOCK BIT(22) +#define CFG_CLK_ALWAYS_ON BIT(18) +#define CFG_AUTO_CLK BIT(23) + +#define SD_EMMC_STATUS 0x48 +#define STATUS_BUSY BIT(31) + +#define SD_EMMC_IRQ_EN 0x4c +#define IRQ_EN_MASK 0x3fff +#define IRQ_RXD_ERR_SHIFT 0 +#define IRQ_RXD_ERR_MASK 0xff +#define IRQ_TXD_ERR BIT(8) +#define IRQ_DESC_ERR BIT(9) +#define IRQ_RESP_ERR BIT(10) +#define IRQ_RESP_TIMEOUT BIT(11) +#define IRQ_DESC_TIMEOUT BIT(12) +#define IRQ_END_OF_CHAIN BIT(13) +#define IRQ_RESP_STATUS BIT(14) +#define IRQ_SDIO BIT(15) + +#define SD_EMMC_CMD_CFG 0x50 +#define SD_EMMC_CMD_ARG 0x54 +#define SD_EMMC_CMD_DAT 0x58 +#define SD_EMMC_CMD_RSP 0x5c +#define SD_EMMC_CMD_RSP1 0x60 +#define SD_EMMC_CMD_RSP2 0x64 +#define SD_EMMC_CMD_RSP3 0x68 + +#define SD_EMMC_RXD 0x94 +#define SD_EMMC_TXD 0x94 +#define SD_EMMC_LAST_REG SD_EMMC_TXD + +#define SD_EMMC_CFG_BLK_SIZE 512 /* internal buffer max: 512 bytes */ +#define SD_EMMC_CFG_RESP_TIMEOUT 256 /* in clock cycles */ +#define SD_EMMC_CFG_CMD_GAP 16 /* in clock cycles */ +#define MUX_CLK_NUM_PARENTS 2 + +struct meson_host { + struct device *dev; + struct mmc_host *mmc; + struct mmc_request *mrq; + struct mmc_command *cmd; + + spinlock_t lock; + void __iomem *regs; + int irq; + u32 ocr_mask; + struct clk *core_clk; + struct clk_mux mux; + struct clk *mux_clk; + struct clk *mux_parent[MUX_CLK_NUM_PARENTS]; + unsigned long mux_parent_rate[MUX_CLK_NUM_PARENTS]; + + struct clk_divider cfg_div; + struct clk *cfg_div_clk; + + unsigned int bounce_buf_size; + void *bounce_buf; + dma_addr_t bounce_dma_addr; + + bool vqmmc_enabled; +}; + +struct sd_emmc_desc { + u32 cmd_cfg; + u32 cmd_arg; + u32 cmd_data; + u32 cmd_resp; +}; +#define CMD_CFG_LENGTH_SHIFT 0 +#define CMD_CFG_LENGTH_MASK 0x1ff +#define CMD_CFG_BLOCK_MODE BIT(9) +#define CMD_CFG_R1B BIT(10) +#define CMD_CFG_END_OF_CHAIN BIT(11) +#define CMD_CFG_TIMEOUT_SHIFT 12 +#define CMD_CFG_TIMEOUT_MASK 0xf +#define CMD_CFG_NO_RESP BIT(16) +#define CMD_CFG_NO_CMD BIT(17) +#define CMD_CFG_DATA_IO BIT(18) +#define CMD_CFG_DATA_WR BIT(19) +#define CMD_CFG_RESP_NOCRC BIT(20) +#define CMD_CFG_RESP_128 BIT(21) +#define CMD_CFG_RESP_NUM BIT(22) +#define CMD_CFG_DATA_NUM BIT(23) +#define CMD_CFG_CMD_INDEX_SHIFT 24 +#define CMD_CFG_CMD_INDEX_MASK 0x3f +#define CMD_CFG_ERROR BIT(30) +#define CMD_CFG_OWNER BIT(31) + +#define CMD_DATA_MASK (~0x3) +#define CMD_DATA_BIG_ENDIAN BIT(1) +#define CMD_DATA_SRAM BIT(0) +#define CMD_RESP_MASK (~0x1) +#define CMD_RESP_SRAM BIT(0) + +static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate) +{ + struct mmc_host *mmc = host->mmc; + int ret = 0; + u32 cfg; + + if (clk_rate) { + if (WARN_ON(clk_rate > mmc->f_max)) + clk_rate = mmc->f_max; + else if (WARN_ON(clk_rate < mmc->f_min)) + clk_rate = mmc->f_min; + } + + if (clk_rate == mmc->actual_clock) + return 0; + + /* stop clock */ + cfg = readl(host->regs + SD_EMMC_CFG); + if (!(cfg & CFG_STOP_CLOCK)) { + cfg |= CFG_STOP_CLOCK; + writel(cfg, host->regs + SD_EMMC_CFG); + } + + dev_dbg(host->dev, "change clock rate %u -> %lu\n", + mmc->actual_clock, clk_rate); + + if (clk_rate == 0) { + mmc->actual_clock = 0; + return 0; + } + + ret = clk_set_rate(host->cfg_div_clk, clk_rate); + if (ret) + dev_warn(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n", + clk_rate, ret); + else if (clk_rate && clk_rate != clk_get_rate(host->cfg_div_clk)) + dev_warn(host->dev, "divider requested rate %lu != actual rate %lu: ret=%d\n", + clk_rate, clk_get_rate(host->cfg_div_clk), ret); + else + mmc->actual_clock = clk_rate; + + /* (re)start clock, if non-zero */ + if (!ret && clk_rate) { + cfg = readl(host->regs + SD_EMMC_CFG); + cfg &= ~CFG_STOP_CLOCK; + writel(cfg, host->regs + SD_EMMC_CFG); + } + + return ret; +} + +/* + * The SD/eMMC IP block has an internal mux and divider used for + * generating the MMC clock. Use the clock framework to create and + * manage these clocks. + */ +static int meson_mmc_clk_init(struct meson_host *host) +{ + struct clk_init_data init; + char clk_name[32]; + int i, ret = 0; + const char *mux_parent_names[MUX_CLK_NUM_PARENTS]; + unsigned int mux_parent_count = 0; + const char *clk_div_parents[1]; + unsigned int f_min = UINT_MAX; + u32 clk_reg, cfg; + + /* get the mux parents */ + for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) { + char name[16]; + + snprintf(name, sizeof(name), "clkin%d", i); + host->mux_parent[i] = devm_clk_get(host->dev, name); + if (IS_ERR(host->mux_parent[i])) { + ret = PTR_ERR(host->mux_parent[i]); + if (PTR_ERR(host->mux_parent[i]) != -EPROBE_DEFER) + dev_err(host->dev, "Missing clock %s\n", name); + host->mux_parent[i] = NULL; + return ret; + } + + host->mux_parent_rate[i] = clk_get_rate(host->mux_parent[i]); + mux_parent_names[i] = __clk_get_name(host->mux_parent[i]); + mux_parent_count++; + if (host->mux_parent_rate[i] < f_min) + f_min = host->mux_parent_rate[i]; + } + + /* cacluate f_min based on input clocks, and max divider value */ + if (f_min != UINT_MAX) + f_min = DIV_ROUND_UP(CLK_SRC_XTAL_RATE, CLK_DIV_MAX); + else + f_min = 4000000; /* default min: 400 MHz */ + host->mmc->f_min = f_min; + + /* create the mux */ + snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev)); + init.name = clk_name; + init.ops = &clk_mux_ops; + init.flags = 0; + init.parent_names = mux_parent_names; + init.num_parents = mux_parent_count; + + host->mux.reg = host->regs + SD_EMMC_CLOCK; + host->mux.shift = CLK_SRC_SHIFT; + host->mux.mask = CLK_SRC_MASK; + host->mux.flags = 0; + host->mux.table = NULL; + host->mux.hw.init = &init; + + host->mux_clk = devm_clk_register(host->dev, &host->mux.hw); + if (WARN_ON(IS_ERR(host->mux_clk))) + return PTR_ERR(host->mux_clk); + + /* create the divider */ + snprintf(clk_name, sizeof(clk_name), "%s#div", dev_name(host->dev)); + init.name = devm_kstrdup(host->dev, clk_name, GFP_KERNEL); + init.ops = &clk_divider_ops; + init.flags = CLK_SET_RATE_PARENT; + clk_div_parents[0] = __clk_get_name(host->mux_clk); + init.parent_names = clk_div_parents; + init.num_parents = ARRAY_SIZE(clk_div_parents); + + host->cfg_div.reg = host->regs + SD_EMMC_CLOCK; + host->cfg_div.shift = CLK_DIV_SHIFT; + host->cfg_div.width = CLK_DIV_WIDTH; + host->cfg_div.hw.init = &init; + host->cfg_div.flags = CLK_DIVIDER_ONE_BASED | + CLK_DIVIDER_ROUND_CLOSEST | CLK_DIVIDER_ALLOW_ZERO; + + host->cfg_div_clk = devm_clk_register(host->dev, &host->cfg_div.hw); + if (WARN_ON(PTR_ERR_OR_ZERO(host->cfg_div_clk))) + return PTR_ERR(host->cfg_div_clk); + + /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */ + clk_reg = 0; + clk_reg |= CLK_PHASE_180 << CLK_PHASE_SHIFT; + clk_reg |= CLK_SRC_XTAL << CLK_SRC_SHIFT; + clk_reg |= CLK_DIV_MAX << CLK_DIV_SHIFT; + clk_reg &= ~CLK_ALWAYS_ON; + writel(clk_reg, host->regs + SD_EMMC_CLOCK); + + /* Ensure clock starts in "auto" mode, not "always on" */ + cfg = readl(host->regs + SD_EMMC_CFG); + cfg &= ~CFG_CLK_ALWAYS_ON; + cfg |= CFG_AUTO_CLK; + writel(cfg, host->regs + SD_EMMC_CFG); + + ret = clk_prepare_enable(host->cfg_div_clk); + if (!ret) + ret = meson_mmc_clk_set(host, f_min); + + if (!ret) + clk_disable_unprepare(host->cfg_div_clk); + + return ret; +} + +static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct meson_host *host = mmc_priv(mmc); + u32 bus_width; + u32 val, orig; + + /* + * GPIO regulator, only controls switching between 1v8 and + * 3v3, doesn't support MMC_POWER_OFF, MMC_POWER_ON. + */ + switch (ios->power_mode) { + case MMC_POWER_OFF: + if (!IS_ERR(mmc->supply.vmmc)) + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); + + if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) { + regulator_disable(mmc->supply.vqmmc); + host->vqmmc_enabled = false; + } + + break; + + case MMC_POWER_UP: + if (!IS_ERR(mmc->supply.vmmc)) + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd); + break; + + case MMC_POWER_ON: + if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) { + int ret = regulator_enable(mmc->supply.vqmmc); + + if (ret < 0) + dev_err(mmc_dev(mmc), + "failed to enable vqmmc regulator\n"); + else + host->vqmmc_enabled = true; + } + + break; + } + + + meson_mmc_clk_set(host, ios->clock); + + /* Bus width */ + val = readl(host->regs + SD_EMMC_CFG); + switch (ios->bus_width) { + case MMC_BUS_WIDTH_1: + bus_width = CFG_BUS_WIDTH_1; + break; + case MMC_BUS_WIDTH_4: + bus_width = CFG_BUS_WIDTH_4; + break; + case MMC_BUS_WIDTH_8: + bus_width = CFG_BUS_WIDTH_8; + break; + default: + dev_err(host->dev, "Invalid ios->bus_width: %u. Setting to 4.\n", + ios->bus_width); + bus_width = CFG_BUS_WIDTH_4; + return; + } + + val = readl(host->regs + SD_EMMC_CFG); + orig = val; + + val &= ~(CFG_BUS_WIDTH_MASK << CFG_BUS_WIDTH_SHIFT); + val |= bus_width << CFG_BUS_WIDTH_SHIFT; + + val &= ~(CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); + val |= ilog2(SD_EMMC_CFG_BLK_SIZE) << CFG_BLK_LEN_SHIFT; + + val &= ~(CFG_RESP_TIMEOUT_MASK << CFG_RESP_TIMEOUT_SHIFT); + val |= ilog2(SD_EMMC_CFG_RESP_TIMEOUT) << CFG_RESP_TIMEOUT_SHIFT; + + val &= ~(CFG_RC_CC_MASK << CFG_RC_CC_SHIFT); + val |= ilog2(SD_EMMC_CFG_CMD_GAP) << CFG_RC_CC_SHIFT; + + writel(val, host->regs + SD_EMMC_CFG); + + if (val != orig) + dev_dbg(host->dev, "%s: SD_EMMC_CFG: 0x%08x -> 0x%08x\n", + __func__, orig, val); +} + +static int meson_mmc_request_done(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct meson_host *host = mmc_priv(mmc); + + WARN_ON(host->mrq != mrq); + + host->mrq = NULL; + host->cmd = NULL; + mmc_request_done(host->mmc, mrq); + + return 0; +} + +static void meson_mmc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd) +{ + struct meson_host *host = mmc_priv(mmc); + struct sd_emmc_desc *desc, desc_tmp; + u32 cfg; + u8 blk_len, cmd_cfg_timeout; + unsigned int xfer_bytes = 0; + + /* Setup descriptors */ + dma_rmb(); + desc = &desc_tmp; + memset(desc, 0, sizeof(struct sd_emmc_desc)); + + desc->cmd_cfg |= (cmd->opcode & CMD_CFG_CMD_INDEX_MASK) << + CMD_CFG_CMD_INDEX_SHIFT; + desc->cmd_cfg |= CMD_CFG_OWNER; /* owned by CPU */ + desc->cmd_arg = cmd->arg; + + /* Response */ + if (cmd->flags & MMC_RSP_PRESENT) { + desc->cmd_cfg &= ~CMD_CFG_NO_RESP; + if (cmd->flags & MMC_RSP_136) + desc->cmd_cfg |= CMD_CFG_RESP_128; + desc->cmd_cfg |= CMD_CFG_RESP_NUM; + desc->cmd_resp = 0; + + if (!(cmd->flags & MMC_RSP_CRC)) + desc->cmd_cfg |= CMD_CFG_RESP_NOCRC; + + if (cmd->flags & MMC_RSP_BUSY) + desc->cmd_cfg |= CMD_CFG_R1B; + } else { + desc->cmd_cfg |= CMD_CFG_NO_RESP; + } + + /* data? */ + if (cmd->data) { + desc->cmd_cfg |= CMD_CFG_DATA_IO; + if (cmd->data->blocks > 1) { + desc->cmd_cfg |= CMD_CFG_BLOCK_MODE; + desc->cmd_cfg |= + (cmd->data->blocks & CMD_CFG_LENGTH_MASK) << + CMD_CFG_LENGTH_SHIFT; + + /* check if block-size matches, if not update */ + cfg = readl(host->regs + SD_EMMC_CFG); + blk_len = cfg & (CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); + blk_len >>= CFG_BLK_LEN_SHIFT; + if (blk_len != ilog2(cmd->data->blksz)) { + dev_warn(host->dev, "%s: update blk_len %d -> %d\n", + __func__, blk_len, + ilog2(cmd->data->blksz)); + blk_len = ilog2(cmd->data->blksz); + cfg &= ~(CFG_BLK_LEN_MASK << CFG_BLK_LEN_SHIFT); + cfg |= blk_len << CFG_BLK_LEN_SHIFT; + writel(cfg, host->regs + SD_EMMC_CFG); + } + } else { + desc->cmd_cfg &= ~CMD_CFG_BLOCK_MODE; + desc->cmd_cfg |= + (cmd->data->blksz & CMD_CFG_LENGTH_MASK) << + CMD_CFG_LENGTH_SHIFT; + } + + cmd->data->bytes_xfered = 0; + xfer_bytes = cmd->data->blksz * cmd->data->blocks; + if (cmd->data->flags & MMC_DATA_WRITE) { + desc->cmd_cfg |= CMD_CFG_DATA_WR; + WARN_ON(xfer_bytes > host->bounce_buf_size); + sg_copy_to_buffer(cmd->data->sg, cmd->data->sg_len, + host->bounce_buf, xfer_bytes); + cmd->data->bytes_xfered = xfer_bytes; + dma_wmb(); + } else { + desc->cmd_cfg &= ~CMD_CFG_DATA_WR; + } + + if (xfer_bytes > 0) { + desc->cmd_cfg &= ~CMD_CFG_DATA_NUM; + desc->cmd_data = host->bounce_dma_addr & CMD_DATA_MASK; + } else { + /* write data to data_addr */ + desc->cmd_cfg |= CMD_CFG_DATA_NUM; + desc->cmd_data = 0; + } + + cmd_cfg_timeout = 12; + } else { + desc->cmd_cfg &= ~CMD_CFG_DATA_IO; + cmd_cfg_timeout = 10; + } + desc->cmd_cfg |= (cmd_cfg_timeout & CMD_CFG_TIMEOUT_MASK) << + CMD_CFG_TIMEOUT_SHIFT; + + host->cmd = cmd; + + /* Last descriptor */ + desc->cmd_cfg |= CMD_CFG_END_OF_CHAIN; + writel(desc->cmd_cfg, host->regs + SD_EMMC_CMD_CFG); + writel(desc->cmd_data, host->regs + SD_EMMC_CMD_DAT); + writel(desc->cmd_resp, host->regs + SD_EMMC_CMD_RSP); + wmb(); /* ensure descriptor is written before kicked */ + writel(desc->cmd_arg, host->regs + SD_EMMC_CMD_ARG); +} + +static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct meson_host *host = mmc_priv(mmc); + + WARN_ON(host->mrq != NULL); + + /* Stop execution */ + writel(0, host->regs + SD_EMMC_START); + + /* clear, ack, enable all interrupts */ + writel(0, host->regs + SD_EMMC_IRQ_EN); + writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); + writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN); + + host->mrq = mrq; + + if (mrq->sbc) + meson_mmc_start_cmd(mmc, mrq->sbc); + else + meson_mmc_start_cmd(mmc, mrq->cmd); +} + +static int meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd) +{ + struct meson_host *host = mmc_priv(mmc); + + if (cmd->flags & MMC_RSP_136) { + cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP3); + cmd->resp[1] = readl(host->regs + SD_EMMC_CMD_RSP2); + cmd->resp[2] = readl(host->regs + SD_EMMC_CMD_RSP1); + cmd->resp[3] = readl(host->regs + SD_EMMC_CMD_RSP); + } else if (cmd->flags & MMC_RSP_PRESENT) { + cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP); + } + + return 0; +} + +static irqreturn_t meson_mmc_irq(int irq, void *dev_id) +{ + struct meson_host *host = dev_id; + struct mmc_request *mrq; + struct mmc_command *cmd = host->cmd; + u32 irq_en, status, raw_status; + irqreturn_t ret = IRQ_HANDLED; + + if (WARN_ON(!host)) + return IRQ_NONE; + + mrq = host->mrq; + + if (WARN_ON(!mrq)) + return IRQ_NONE; + + if (WARN_ON(!cmd)) + return IRQ_NONE; + + spin_lock(&host->lock); + irq_en = readl(host->regs + SD_EMMC_IRQ_EN); + raw_status = readl(host->regs + SD_EMMC_STATUS); + status = raw_status & irq_en; + + if (!status) { + dev_warn(host->dev, "Spurious IRQ! status=0x%08x, irq_en=0x%08x\n", + raw_status, irq_en); + ret = IRQ_NONE; + goto out; + } + + cmd->error = 0; + if (status & IRQ_RXD_ERR_MASK) { + dev_dbg(host->dev, "Unhandled IRQ: RXD error\n"); + cmd->error = -EILSEQ; + } + if (status & IRQ_TXD_ERR) { + dev_dbg(host->dev, "Unhandled IRQ: TXD error\n"); + cmd->error = -EILSEQ; + } + if (status & IRQ_DESC_ERR) + dev_dbg(host->dev, "Unhandled IRQ: Descriptor error\n"); + if (status & IRQ_RESP_ERR) { + dev_dbg(host->dev, "Unhandled IRQ: Response error\n"); + cmd->error = -EILSEQ; + } + if (status & IRQ_RESP_TIMEOUT) { + dev_dbg(host->dev, "Unhandled IRQ: Response timeout\n"); + cmd->error = -ETIMEDOUT; + } + if (status & IRQ_DESC_TIMEOUT) { + dev_dbg(host->dev, "Unhandled IRQ: Descriptor timeout\n"); + cmd->error = -ETIMEDOUT; + } + if (status & IRQ_SDIO) + dev_dbg(host->dev, "Unhandled IRQ: SDIO.\n"); + + if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) + ret = IRQ_WAKE_THREAD; + else { + dev_warn(host->dev, "Unknown IRQ! status=0x%04x: MMC CMD%u arg=0x%08x flags=0x%08x stop=%d\n", + status, cmd->opcode, cmd->arg, + cmd->flags, mrq->stop ? 1 : 0); + if (cmd->data) { + struct mmc_data *data = cmd->data; + + dev_warn(host->dev, "\tblksz %u blocks %u flags 0x%08x (%s%s)", + data->blksz, data->blocks, data->flags, + data->flags & MMC_DATA_WRITE ? "write" : "", + data->flags & MMC_DATA_READ ? "read" : ""); + } + } + +out: + /* ack all (enabled) interrupts */ + writel(status, host->regs + SD_EMMC_STATUS); + + if (ret == IRQ_HANDLED) { + meson_mmc_read_resp(host->mmc, cmd); + meson_mmc_request_done(host->mmc, cmd->mrq); + } + + spin_unlock(&host->lock); + return ret; +} + +static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id) +{ + struct meson_host *host = dev_id; + struct mmc_request *mrq = host->mrq; + struct mmc_command *cmd = host->cmd; + struct mmc_data *data; + unsigned int xfer_bytes; + int ret = IRQ_HANDLED; + + if (WARN_ON(!mrq)) + ret = IRQ_NONE; + + if (WARN_ON(!cmd)) + ret = IRQ_NONE; + + data = cmd->data; + if (data) { + xfer_bytes = data->blksz * data->blocks; + if (data->flags & MMC_DATA_READ) { + WARN_ON(xfer_bytes > host->bounce_buf_size); + sg_copy_from_buffer(data->sg, data->sg_len, + host->bounce_buf, xfer_bytes); + data->bytes_xfered = xfer_bytes; + } + } + + meson_mmc_read_resp(host->mmc, cmd); + if (!data || !data->stop || mrq->sbc) + meson_mmc_request_done(host->mmc, mrq); + else + meson_mmc_start_cmd(host->mmc, data->stop); + + return ret; +} + +/* + * NOTE: we only need this until the GPIO/pinctrl driver can handle + * interrupts. For now, the MMC core will use this for polling. + */ +static int meson_mmc_get_cd(struct mmc_host *mmc) +{ + int status = mmc_gpio_get_cd(mmc); + + if (status == -ENOSYS) + return 1; /* assume present */ + + return status; +} + +static const struct mmc_host_ops meson_mmc_ops = { + .request = meson_mmc_request, + .set_ios = meson_mmc_set_ios, + .get_cd = meson_mmc_get_cd, +}; + +static int meson_mmc_probe(struct platform_device *pdev) +{ + struct resource *res; + struct meson_host *host; + struct mmc_host *mmc; + int ret; + + mmc = mmc_alloc_host(sizeof(struct meson_host), &pdev->dev); + if (!mmc) + return -ENOMEM; + host = mmc_priv(mmc); + host->mmc = mmc; + host->dev = &pdev->dev; + dev_set_drvdata(&pdev->dev, host); + + spin_lock_init(&host->lock); + + /* Get regulators and the supported OCR mask */ + host->vqmmc_enabled = false; + ret = mmc_regulator_get_supply(mmc); + if (ret == -EPROBE_DEFER) + goto free_host; + + ret = mmc_of_parse(mmc); + if (ret) { + dev_warn(&pdev->dev, "error parsing DT: %d\n", ret); + goto free_host; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->regs)) { + ret = PTR_ERR(host->regs); + goto free_host; + } + + host->irq = platform_get_irq(pdev, 0); + if (host->irq == 0) { + dev_err(&pdev->dev, "failed to get interrupt resource.\n"); + ret = -EINVAL; + goto free_host; + } + + host->core_clk = devm_clk_get(&pdev->dev, "core"); + if (IS_ERR(host->core_clk)) { + ret = PTR_ERR(host->core_clk); + goto free_host; + } + + ret = clk_prepare_enable(host->core_clk); + if (ret) + goto free_host; + + ret = meson_mmc_clk_init(host); + if (ret) + goto free_host; + + /* Stop execution */ + writel(0, host->regs + SD_EMMC_START); + + /* clear, ack, enable all interrupts */ + writel(0, host->regs + SD_EMMC_IRQ_EN); + writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS); + + ret = devm_request_threaded_irq(&pdev->dev, host->irq, + meson_mmc_irq, meson_mmc_irq_thread, + IRQF_SHARED, DRIVER_NAME, host); + if (ret) + goto free_host; + + /* data bounce buffer */ + host->bounce_buf_size = SZ_512K; + host->bounce_buf = + dma_alloc_coherent(host->dev, host->bounce_buf_size, + &host->bounce_dma_addr, GFP_KERNEL); + if (host->bounce_buf == NULL) { + dev_err(host->dev, "Unable to map allocate DMA bounce buffer.\n"); + ret = -ENOMEM; + goto free_host; + } + + mmc->ops = &meson_mmc_ops; + mmc_add_host(mmc); + + return 0; + +free_host: + clk_disable_unprepare(host->cfg_div_clk); + clk_disable_unprepare(host->core_clk); + mmc_free_host(mmc); + return ret; +} + +static int meson_mmc_remove(struct platform_device *pdev) +{ + struct meson_host *host = dev_get_drvdata(&pdev->dev); + + if (WARN_ON(!host)) + return 0; + + if (host->bounce_buf) + dma_free_coherent(host->dev, host->bounce_buf_size, + host->bounce_buf, host->bounce_dma_addr); + + clk_disable_unprepare(host->cfg_div_clk); + clk_disable_unprepare(host->core_clk); + + mmc_free_host(host->mmc); + return 0; +} + +static const struct of_device_id meson_mmc_of_match[] = { + { .compatible = "amlogic,meson-gx-mmc", }, + { .compatible = "amlogic,meson-gxbb-mmc", }, + { .compatible = "amlogic,meson-gxl-mmc", }, + { .compatible = "amlogic,meson-gxm-mmc", }, + {} +}; +MODULE_DEVICE_TABLE(of, meson_mmc_of_match); + +static struct platform_driver meson_mmc_driver = { + .probe = meson_mmc_probe, + .remove = meson_mmc_remove, + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(meson_mmc_of_match), + }, +}; + +module_platform_driver(meson_mmc_driver); + +MODULE_ALIAS("platform:" DRIVER_NAME); +MODULE_DESCRIPTION("Amlogic S905/GXBB SD/eMMC driver"); +MODULE_AUTHOR("Kevin Hilman <khilman@baylibre.com>"); +MODULE_LICENSE("GPL v2"); +
Initial support for the SD/eMMC controller in the Amlogic S905/GX* family of SoCs. Signed-off-by: Kevin Hilman <khilman@baylibre.com> --- Changes from v3: - better handling of clock error paths - rename to meson-gx to reflect support for newer SoCs - has now been tested with SDIO .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 33 + MAINTAINERS | 1 + drivers/mmc/host/Kconfig | 10 + drivers/mmc/host/Makefile | 1 + drivers/mmc/host/meson-gx.c | 853 +++++++++++++++++++++ 5 files changed, 898 insertions(+) create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt create mode 100644 drivers/mmc/host/meson-gx.c