diff mbox

[v3,3/3] arm: omap3: cm-t35: add support for cm-t3730

Message ID 1308086174-3080-3-git-send-email-grinberg@compulab.co.il (mailing list archive)
State Accepted
Commit 685b7a95ba32ef4a79dd64aebe637df584c6dca6
Headers show

Commit Message

Igor Grinberg June 14, 2011, 9:16 p.m. UTC 
cm-t3730 is basically the same board as cm-t35,
but has AM/DM3730 SoC assembled and therefore some changes are required.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mike Rapoport <mike@compulab.co.il>
---
v3:	fix MACH_* selection
	remove completely the use of cpu_is_*
v2:	Add debug uart entry


 arch/arm/mach-omap2/Kconfig                  |    6 ++-
 arch/arm/mach-omap2/board-cm-t35.c           |   77 ++++++++++++++++++++-----
 arch/arm/plat-omap/include/plat/uncompress.h |    1 +
 3 files changed, 67 insertions(+), 17 deletions(-)

Comments

Igor Grinberg June 22, 2011, 2:56 p.m. UTC | #1 
Tony,

Does this one look better?



On 06/15/11 00:16, Igor Grinberg wrote:

> cm-t3730 is basically the same board as cm-t35,
> but has AM/DM3730 SoC assembled and therefore some changes are required.
>
> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
> Acked-by: Mike Rapoport <mike@compulab.co.il>
> ---
> v3:	fix MACH_* selection
> 	remove completely the use of cpu_is_*
> v2:	Add debug uart entry
>
>
>  arch/arm/mach-omap2/Kconfig                  |    6 ++-
>  arch/arm/mach-omap2/board-cm-t35.c           |   77 ++++++++++++++++++++-----
>  arch/arm/plat-omap/include/plat/uncompress.h |    1 +
>  3 files changed, 67 insertions(+), 17 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
> index 19d5891..4ae6257 100644
> --- a/arch/arm/mach-omap2/Kconfig
> +++ b/arch/arm/mach-omap2/Kconfig
> @@ -266,9 +266,10 @@ config MACH_OMAP_ZOOM3
>  	select REGULATOR_FIXED_VOLTAGE
>  
>  config MACH_CM_T35
> -	bool "CompuLab CM-T35 module"
> +	bool "CompuLab CM-T35/CM-T3730 modules"
>  	depends on ARCH_OMAP3
>  	default y
> +	select MACH_CM_T3730
>  	select OMAP_PACKAGE_CUS
>  
>  config MACH_CM_T3517
> @@ -277,6 +278,9 @@ config MACH_CM_T3517
>  	default y
>  	select OMAP_PACKAGE_CBB
>  
> +config MACH_CM_T3730
> +       bool
> +
>  config MACH_IGEP0020
>  	bool "IGEP v2 board"
>  	depends on ARCH_OMAP3
> diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
> index 256b81c..ea31281 100644
> --- a/arch/arm/mach-omap2/board-cm-t35.c
> +++ b/arch/arm/mach-omap2/board-cm-t35.c
> @@ -1,5 +1,5 @@
>  /*
> - * board-cm-t35.c (CompuLab CM-T35 module)
> + * CompuLab CM-T35/CM-T3730 modules support
>   *
>   * Copyright (C) 2009-2011 CompuLab, Ltd.
>   * Authors: Mike Rapoport <mike@compulab.co.il>
> @@ -574,17 +574,11 @@ static struct omap_board_mux board_mux[] __initdata = {
>  	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
>  
> -	/* DSS */
> +	/* common DSS */
>  	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> @@ -597,12 +591,6 @@ static struct omap_board_mux board_mux[] __initdata = {
>  	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
> -	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>  
>  	/* display controls */
>  	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
> @@ -615,19 +603,53 @@ static struct omap_board_mux board_mux[] __initdata = {
>  
>  	{ .reg_offset = OMAP_MUX_TERMINATOR },
>  };
> +
> +static void __init cm_t3x_common_dss_mux_init(int mux_mode)
> +{
> +	omap_mux_init_signal("dss_data18", mux_mode);
> +	omap_mux_init_signal("dss_data19", mux_mode);
> +	omap_mux_init_signal("dss_data20", mux_mode);
> +	omap_mux_init_signal("dss_data21", mux_mode);
> +	omap_mux_init_signal("dss_data22", mux_mode);
> +	omap_mux_init_signal("dss_data23", mux_mode);
> +}
> +
> +static void __init cm_t35_init_mux(void)
> +{
> +	omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
> +}
> +
> +static void __init cm_t3730_init_mux(void)
> +{
> +	omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
> +}
> +#else
> +static inline void cm_t35_init_mux(void) {}
> +static inline void cm_t3730_init_mux(void) {}
>  #endif
>  
>  static struct omap_board_config_kernel cm_t35_config[] __initdata = {
>  };
>  
> -static void __init cm_t35_init(void)
> +static void __init cm_t3x_common_init(void)
>  {
>  	omap_board_config = cm_t35_config;
>  	omap_board_config_size = ARRAY_SIZE(cm_t35_config);
>  	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
>  	omap_serial_init();
>  	cm_t35_init_i2c();
> -	cm_t35_init_nand();
>  	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
>  	cm_t35_init_ethernet();
>  	cm_t35_init_led();
> @@ -637,6 +659,19 @@ static void __init cm_t35_init(void)
>  	usbhs_init(&usbhs_bdata);
>  }
>  
> +static void __init cm_t35_init(void)
> +{
> +	cm_t3x_common_init();
> +	cm_t35_init_mux();
> +	cm_t35_init_nand();
> +}
> +
> +static void __init cm_t3730_init(void)
> +{
> +	cm_t3x_common_init();
> +	cm_t3730_init_mux();
> +}
> +
>  MACHINE_START(CM_T35, "Compulab CM-T35")
>  	.boot_params	= 0x80000100,
>  	.reserve	= omap_reserve,
> @@ -646,3 +681,13 @@ MACHINE_START(CM_T35, "Compulab CM-T35")
>  	.init_machine	= cm_t35_init,
>  	.timer		= &omap_timer,
>  MACHINE_END
> +
> +MACHINE_START(CM_T3730, "Compulab CM-T3730")
> +	.boot_params    = 0x80000100,
> +	.reserve        = omap_reserve,
> +	.map_io         = omap3_map_io,
> +	.init_early     = cm_t35_init_early,
> +	.init_irq       = omap_init_irq,
> +	.init_machine   = cm_t3730_init,
> +	.timer          = &omap_timer,
> +MACHINE_END
> diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
> index ac4b60d..a067484 100644
> --- a/arch/arm/plat-omap/include/plat/uncompress.h
> +++ b/arch/arm/plat-omap/include/plat/uncompress.h
> @@ -148,6 +148,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
>  		/* omap3 based boards using UART3 */
>  		DEBUG_LL_OMAP3(3, cm_t35);
>  		DEBUG_LL_OMAP3(3, cm_t3517);
> +		DEBUG_LL_OMAP3(3, cm_t3730);
>  		DEBUG_LL_OMAP3(3, craneboard);
>  		DEBUG_LL_OMAP3(3, devkit8000);
>  		DEBUG_LL_OMAP3(3, igep0020);
Igor Grinberg June 27, 2011, 8:35 a.m. UTC | #2 
Tony,

I'd really like us to decide, because I want my (currently) out of tree port
to be based on one of the patches (v2 or v3).

Can you please, look into this?

Thanks

On 06/22/11 17:56, Igor Grinberg wrote:
> Tony,
>
> Does this one look better?
>
>
>
> On 06/15/11 00:16, Igor Grinberg wrote:
>
>> cm-t3730 is basically the same board as cm-t35,
>> but has AM/DM3730 SoC assembled and therefore some changes are required.
>>
>> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
>> Acked-by: Mike Rapoport <mike@compulab.co.il>
>> ---
>> v3:	fix MACH_* selection
>> 	remove completely the use of cpu_is_*
>> v2:	Add debug uart entry
>>
>>
>>  arch/arm/mach-omap2/Kconfig                  |    6 ++-
>>  arch/arm/mach-omap2/board-cm-t35.c           |   77 ++++++++++++++++++++-----
>>  arch/arm/plat-omap/include/plat/uncompress.h |    1 +
>>  3 files changed, 67 insertions(+), 17 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
>> index 19d5891..4ae6257 100644
>> --- a/arch/arm/mach-omap2/Kconfig
>> +++ b/arch/arm/mach-omap2/Kconfig
>> @@ -266,9 +266,10 @@ config MACH_OMAP_ZOOM3
>>  	select REGULATOR_FIXED_VOLTAGE
>>  
>>  config MACH_CM_T35
>> -	bool "CompuLab CM-T35 module"
>> +	bool "CompuLab CM-T35/CM-T3730 modules"
>>  	depends on ARCH_OMAP3
>>  	default y
>> +	select MACH_CM_T3730
>>  	select OMAP_PACKAGE_CUS
>>  
>>  config MACH_CM_T3517
>> @@ -277,6 +278,9 @@ config MACH_CM_T3517
>>  	default y
>>  	select OMAP_PACKAGE_CBB
>>  
>> +config MACH_CM_T3730
>> +       bool
>> +
>>  config MACH_IGEP0020
>>  	bool "IGEP v2 board"
>>  	depends on ARCH_OMAP3
>> diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
>> index 256b81c..ea31281 100644
>> --- a/arch/arm/mach-omap2/board-cm-t35.c
>> +++ b/arch/arm/mach-omap2/board-cm-t35.c
>> @@ -1,5 +1,5 @@
>>  /*
>> - * board-cm-t35.c (CompuLab CM-T35 module)
>> + * CompuLab CM-T35/CM-T3730 modules support
>>   *
>>   * Copyright (C) 2009-2011 CompuLab, Ltd.
>>   * Authors: Mike Rapoport <mike@compulab.co.il>
>> @@ -574,17 +574,11 @@ static struct omap_board_mux board_mux[] __initdata = {
>>  	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
>>  
>> -	/* DSS */
>> +	/* common DSS */
>>  	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> @@ -597,12 +591,6 @@ static struct omap_board_mux board_mux[] __initdata = {
>>  	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>> -	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
>>  
>>  	/* display controls */
>>  	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
>> @@ -615,19 +603,53 @@ static struct omap_board_mux board_mux[] __initdata = {
>>  
>>  	{ .reg_offset = OMAP_MUX_TERMINATOR },
>>  };
>> +
>> +static void __init cm_t3x_common_dss_mux_init(int mux_mode)
>> +{
>> +	omap_mux_init_signal("dss_data18", mux_mode);
>> +	omap_mux_init_signal("dss_data19", mux_mode);
>> +	omap_mux_init_signal("dss_data20", mux_mode);
>> +	omap_mux_init_signal("dss_data21", mux_mode);
>> +	omap_mux_init_signal("dss_data22", mux_mode);
>> +	omap_mux_init_signal("dss_data23", mux_mode);
>> +}
>> +
>> +static void __init cm_t35_init_mux(void)
>> +{
>> +	omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
>> +}
>> +
>> +static void __init cm_t3730_init_mux(void)
>> +{
>> +	omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
>> +}
>> +#else
>> +static inline void cm_t35_init_mux(void) {}
>> +static inline void cm_t3730_init_mux(void) {}
>>  #endif
>>  
>>  static struct omap_board_config_kernel cm_t35_config[] __initdata = {
>>  };
>>  
>> -static void __init cm_t35_init(void)
>> +static void __init cm_t3x_common_init(void)
>>  {
>>  	omap_board_config = cm_t35_config;
>>  	omap_board_config_size = ARRAY_SIZE(cm_t35_config);
>>  	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
>>  	omap_serial_init();
>>  	cm_t35_init_i2c();
>> -	cm_t35_init_nand();
>>  	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
>>  	cm_t35_init_ethernet();
>>  	cm_t35_init_led();
>> @@ -637,6 +659,19 @@ static void __init cm_t35_init(void)
>>  	usbhs_init(&usbhs_bdata);
>>  }
>>  
>> +static void __init cm_t35_init(void)
>> +{
>> +	cm_t3x_common_init();
>> +	cm_t35_init_mux();
>> +	cm_t35_init_nand();
>> +}
>> +
>> +static void __init cm_t3730_init(void)
>> +{
>> +	cm_t3x_common_init();
>> +	cm_t3730_init_mux();
>> +}
>> +
>>  MACHINE_START(CM_T35, "Compulab CM-T35")
>>  	.boot_params	= 0x80000100,
>>  	.reserve	= omap_reserve,
>> @@ -646,3 +681,13 @@ MACHINE_START(CM_T35, "Compulab CM-T35")
>>  	.init_machine	= cm_t35_init,
>>  	.timer		= &omap_timer,
>>  MACHINE_END
>> +
>> +MACHINE_START(CM_T3730, "Compulab CM-T3730")
>> +	.boot_params    = 0x80000100,
>> +	.reserve        = omap_reserve,
>> +	.map_io         = omap3_map_io,
>> +	.init_early     = cm_t35_init_early,
>> +	.init_irq       = omap_init_irq,
>> +	.init_machine   = cm_t3730_init,
>> +	.timer          = &omap_timer,
>> +MACHINE_END
>> diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
>> index ac4b60d..a067484 100644
>> --- a/arch/arm/plat-omap/include/plat/uncompress.h
>> +++ b/arch/arm/plat-omap/include/plat/uncompress.h
>> @@ -148,6 +148,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
>>  		/* omap3 based boards using UART3 */
>>  		DEBUG_LL_OMAP3(3, cm_t35);
>>  		DEBUG_LL_OMAP3(3, cm_t3517);
>> +		DEBUG_LL_OMAP3(3, cm_t3730);
>>  		DEBUG_LL_OMAP3(3, craneboard);
>>  		DEBUG_LL_OMAP3(3, devkit8000);
>>  		DEBUG_LL_OMAP3(3, igep0020);
Tony Lindgren June 27, 2011, 10:21 a.m. UTC | #3 
* Igor Grinberg <grinberg@compulab.co.il> [110627 01:31]:
> Tony,
> 
> I'd really like us to decide, because I want my (currently) out of tree port
> to be based on one of the patches (v2 or v3).
> 
> Can you please, look into this?

Sorry for the delay, yes that looks good to me. Will add to devel-board branch.

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Igor Grinberg June 27, 2011, 12:31 p.m. UTC | #4 
On 06/27/11 13:21, Tony Lindgren wrote:

> * Igor Grinberg <grinberg@compulab.co.il> [110627 01:31]:
>> Tony,
>>
>> I'd really like us to decide, because I want my (currently) out of tree port
>> to be based on one of the patches (v2 or v3).
>>
>> Can you please, look into this?
> Sorry for the delay, yes that looks good to me. Will add to devel-board branch.

Thanks,

please also, don't forget the 1/3 and 2/3 trivial patches.
diff mbox

Patch

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 19d5891..4ae6257 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -266,9 +266,10 @@  config MACH_OMAP_ZOOM3
 	select REGULATOR_FIXED_VOLTAGE
 
 config MACH_CM_T35
-	bool "CompuLab CM-T35 module"
+	bool "CompuLab CM-T35/CM-T3730 modules"
 	depends on ARCH_OMAP3
 	default y
+	select MACH_CM_T3730
 	select OMAP_PACKAGE_CUS
 
 config MACH_CM_T3517
@@ -277,6 +278,9 @@  config MACH_CM_T3517
 	default y
 	select OMAP_PACKAGE_CBB
 
+config MACH_CM_T3730
+       bool
+
 config MACH_IGEP0020
 	bool "IGEP v2 board"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 256b81c..ea31281 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -1,5 +1,5 @@ 
 /*
- * board-cm-t35.c (CompuLab CM-T35 module)
+ * CompuLab CM-T35/CM-T3730 modules support
  *
  * Copyright (C) 2009-2011 CompuLab, Ltd.
  * Authors: Mike Rapoport <mike@compulab.co.il>
@@ -574,17 +574,11 @@  static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
 
-	/* DSS */
+	/* common DSS */
 	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
@@ -597,12 +591,6 @@  static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 
 	/* display controls */
 	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
@@ -615,19 +603,53 @@  static struct omap_board_mux board_mux[] __initdata = {
 
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
+
+static void __init cm_t3x_common_dss_mux_init(int mux_mode)
+{
+	omap_mux_init_signal("dss_data18", mux_mode);
+	omap_mux_init_signal("dss_data19", mux_mode);
+	omap_mux_init_signal("dss_data20", mux_mode);
+	omap_mux_init_signal("dss_data21", mux_mode);
+	omap_mux_init_signal("dss_data22", mux_mode);
+	omap_mux_init_signal("dss_data23", mux_mode);
+}
+
+static void __init cm_t35_init_mux(void)
+{
+	omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+}
+
+static void __init cm_t3730_init_mux(void)
+{
+	omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+	cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+}
+#else
+static inline void cm_t35_init_mux(void) {}
+static inline void cm_t3730_init_mux(void) {}
 #endif
 
 static struct omap_board_config_kernel cm_t35_config[] __initdata = {
 };
 
-static void __init cm_t35_init(void)
+static void __init cm_t3x_common_init(void)
 {
 	omap_board_config = cm_t35_config;
 	omap_board_config_size = ARRAY_SIZE(cm_t35_config);
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
 	omap_serial_init();
 	cm_t35_init_i2c();
-	cm_t35_init_nand();
 	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
 	cm_t35_init_ethernet();
 	cm_t35_init_led();
@@ -637,6 +659,19 @@  static void __init cm_t35_init(void)
 	usbhs_init(&usbhs_bdata);
 }
 
+static void __init cm_t35_init(void)
+{
+	cm_t3x_common_init();
+	cm_t35_init_mux();
+	cm_t35_init_nand();
+}
+
+static void __init cm_t3730_init(void)
+{
+	cm_t3x_common_init();
+	cm_t3730_init_mux();
+}
+
 MACHINE_START(CM_T35, "Compulab CM-T35")
 	.boot_params	= 0x80000100,
 	.reserve	= omap_reserve,
@@ -646,3 +681,13 @@  MACHINE_START(CM_T35, "Compulab CM-T35")
 	.init_machine	= cm_t35_init,
 	.timer		= &omap_timer,
 MACHINE_END
+
+MACHINE_START(CM_T3730, "Compulab CM-T3730")
+	.boot_params    = 0x80000100,
+	.reserve        = omap_reserve,
+	.map_io         = omap3_map_io,
+	.init_early     = cm_t35_init_early,
+	.init_irq       = omap_init_irq,
+	.init_machine   = cm_t3730_init,
+	.timer          = &omap_timer,
+MACHINE_END
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index ac4b60d..a067484 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -148,6 +148,7 @@  static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap3 based boards using UART3 */
 		DEBUG_LL_OMAP3(3, cm_t35);
 		DEBUG_LL_OMAP3(3, cm_t3517);
+		DEBUG_LL_OMAP3(3, cm_t3730);
 		DEBUG_LL_OMAP3(3, craneboard);
 		DEBUG_LL_OMAP3(3, devkit8000);
 		DEBUG_LL_OMAP3(3, igep0020);