diff mbox

[4/5] ARM: dts: qcom-apq8064: Collapse usb support into one node

Message ID 20170127004728.22490-5-stephen.boyd@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Stephen Boyd Jan. 27, 2017, 12:47 a.m. UTC 
We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse the three nodes into one USB device
node, reflecting the true nature of the hardware.

Since we're here, we also mark the irq trigger flags correctly,
as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts |  49 +++----
 arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts |  21 +--
 arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts        |  54 ++++---
 arch/arm/boot/dts/qcom-apq8064-ifc6410.dts         |  54 ++++---
 .../arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts |  16 +--
 arch/arm/boot/dts/qcom-apq8064.dtsi                | 156 ++++++++++++---------
 6 files changed, 170 insertions(+), 180 deletions(-)

Comments

John Stultz Feb. 28, 2017, 11:50 p.m. UTC | #1 
On Thu, Jan 26, 2017 at 4:47 PM, Stephen Boyd <stephen.boyd@linaro.org> wrote:
> We currently have three device nodes for the same USB hardware
> block, as evident by the reuse of the same reg address multiple
> times. Now that the chipidea driver fully supports OTG with the
> MSM wrapper we can collapse the three nodes into one USB device
> node, reflecting the true nature of the hardware.
>
> Since we're here, we also mark the irq trigger flags correctly,
> as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
> Cc: John Stultz <john.stultz@linaro.org>
> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>


Applies with noise now, but I was able to get USB working with this
and some changes to my config.

Hotplug still doesn't work, but that was the same situation before as
well, so I need to dig on that.

So..
Tested-by: John Stultz <john.stultz@linaro.org>

thanks
-john
diff mbox

Patch

diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index 39ae2bc8cb08..eb2d0402c0f8 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -290,44 +290,37 @@ 
 			target-supply	= <&pm8921_lvs7>;
 		};
 
-		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			dr_mode		= "peripheral";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "peripheral";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		usb@12520000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		usb@12530000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index e39440a86739..e5fef32342da 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -320,22 +320,15 @@ 
 			};
 		};
 
-		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-			dr_mode		= "otg";
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index 35f1d46edded..d7362033a91b 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -149,43 +149,37 @@ 
 			};
 		};
 
-		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "ok";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "ok";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		/* on board fixed 3.3v supply */
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index 3d37cab3b9a9..ec0b16fc48a1 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -262,43 +262,37 @@ 
 			target-supply	= <&pm8921_s4>;
 		};
 
-		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		pci@1b500000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
index ebd675ca94b4..e9083542d383 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
@@ -349,15 +349,15 @@ 
 			};
 		};
 
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		gadget@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		gsbi@1a200000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 268bd470c865..07b41b41f9ce 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -179,7 +179,7 @@ 
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
@@ -191,7 +191,7 @@ 
 			clock-frequency = <27000000>;
 		};
 
-		sleep_clk {
+		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
@@ -848,81 +848,97 @@ 
 			};
 		};
 
-		usb1_phy: phy@12500000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-
-			clocks		= <&gcc USB_HS1_XCVR_CLK>,
-					  <&gcc USB_HS1_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS1_RESET>;
-			reset-names	= "link";
-		};
-
-		usb3_phy: phy@12520000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS3_XCVR_CLK>,
-					  <&gcc USB_HS3_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS3_RESET>;
-			reset-names	= "link";
-		};
-
-		usb4_phy: phy@12530000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS4_XCVR_CLK>,
-					  <&gcc USB_HS4_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS4_RESET>;
-			reset-names	= "link";
-		};
-
-		gadget1: gadget@12500000 {
-			compatible	= "qcom,ci-hdrc";
-			reg		= <0x12500000 0x400>;
-			status		= "disabled";
-			dr_mode		= "peripheral";
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			usb-phy		= <&usb1_phy>;
-		};
-
 		usb1: usb@12500000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb1_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb3: usb@12520000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb3_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12520000 0x200>,
+			      <0x12520200 0x200>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS3_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs3_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs3_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb3 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb4: usb@12530000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb4_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12530000 0x200>,
+			      <0x12530200 0x200>;
+			interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS4_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs4_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs4_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb4 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		sata_phy0: phy@1b400000 {