diff mbox

[v2] arm64: dts: ls1088a: Add TMU device tree support

Message ID 1494563596-48185-1-git-send-email-andy.tang@nxp.com (mailing list archive)
State New, archived
Headers show

Commit Message

Andy Tang May 12, 2017, 4:33 a.m. UTC 
Add nodes and properties for thermal management support.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
---
v2:
	- put tmu node in ip block address order

 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 88 ++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)

Comments

Shawn Guo May 15, 2017, 2:25 a.m. UTC | #1 
On Fri, May 12, 2017 at 12:33:16PM +0800, Yuantian Tang wrote:
> Add nodes and properties for thermal management support.
> 
> Signed-off-by: Tang Yuantian <andy.tang@nxp.com>

Applied, thanks.
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index caecd14..c4109fb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -44,6 +44,7 @@ 
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	compatible = "fsl,ls1088a";
@@ -61,6 +62,7 @@ 
 			compatible = "arm,cortex-a53";
 			reg = <0x0>;
 			clocks = <&clockgen 1 0>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
@@ -89,6 +91,7 @@ 
 			compatible = "arm,cortex-a53";
 			reg = <0x100>;
 			clocks = <&clockgen 1 1>;
+			#cooling-cells = <2>;
 		};
 
 		cpu5: cpu@101 {
@@ -153,6 +156,91 @@ 
 			clocks = <&sysclk>;
 		};
 
+		tmu: tmu@1f80000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f80000 0x0 0x10000>;
+			interrupts = <0 23 0x4>;
+			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+			fsl,tmu-calibration =
+				/* Calibration data group 1 */
+				<0x00000000 0x00000026
+				0x00000001 0x0000002d
+				0x00000002 0x00000032
+				0x00000003 0x00000039
+				0x00000004 0x0000003f
+				0x00000005 0x00000046
+				0x00000006 0x0000004d
+				0x00000007 0x00000054
+				0x00000008 0x0000005a
+				0x00000009 0x00000061
+				0x0000000a 0x0000006a
+				0x0000000b 0x00000071
+				/* Calibration data group 2 */
+				0x00010000 0x00000025
+				0x00010001 0x0000002c
+				0x00010002 0x00000035
+				0x00010003 0x0000003d
+				0x00010004 0x00000045
+				0x00010005 0x0000004e
+				0x00010006 0x00000057
+				0x00010007 0x00000061
+				0x00010008 0x0000006b
+				0x00010009 0x00000076
+				/* Calibration data group 3 */
+				0x00020000 0x00000029
+				0x00020001 0x00000033
+				0x00020002 0x0000003d
+				0x00020003 0x00000049
+				0x00020004 0x00000056
+				0x00020005 0x00000061
+				0x00020006 0x0000006d
+				/* Calibration data group 4 */
+				0x00030000 0x00000021
+				0x00030001 0x0000002a
+				0x00030002 0x0000003c
+				0x00030003 0x0000004e>;
+			little-endian;
+			#thermal-sensor-cells = <1>;
+		};
+
+		thermal-zones {
+			cpu_thermal: cpu-thermal {
+				polling-delay-passive = <1000>;
+				polling-delay = <5000>;
+				thermal-sensors = <&tmu 0>;
+
+				trips {
+					cpu_alert: cpu-alert {
+						temperature = <85000>;
+						hysteresis = <2000>;
+						type = "passive";
+					};
+
+					cpu_crit: cpu-crit {
+						temperature = <95000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+
+				cooling-maps {
+					map0 {
+						trip = <&cpu_alert>;
+						cooling-device =
+							<&cpu0 THERMAL_NO_LIMIT
+							THERMAL_NO_LIMIT>;
+					};
+
+					map1 {
+						trip = <&cpu_alert>;
+						cooling-device =
+							<&cpu4 THERMAL_NO_LIMIT
+							THERMAL_NO_LIMIT>;
+					};
+				};
+			};
+		};
+
 		duart0: serial@21c0500 {
 			compatible = "fsl,ns16550", "ns16550a";
 			reg = <0x0 0x21c0500 0x0 0x100>;