| Message ID | 1498055526-6918-2-git-send-email-amelie.delaunay@st.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | 82a29bf9952acd1be7e76783604686abeb4e5b1d |
| Headers | show |
On 06/21/2017 04:32 PM, Amelie Delaunay wrote: > This patch adds the documentation of device tree bindings > for the STM32 SPI controller. > > Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> > --- > .../devicetree/bindings/spi/spi-stm32.txt | 60 ++++++++++++++++++++++ > 1 file changed, 60 insertions(+) > create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt > > diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt > new file mode 100644 > index 0000000..3958bf6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt > @@ -0,0 +1,60 @@ > +STMicroelectronics STM32 SPI Controller > + > +The STM32 SPI controller is used to communicate with external devices using > +the Serial Peripheral Interface. It supports full-duplex, half-duplex and > +simplex synchronous serial communication with external devices. It supports > +from 4 to 32-bit data size. Although it can be configured as master or slave, > +only master is supported by the driver. > + > +Required properties: > +- compatible: Must be "st,stm32-spi". Hi Amelie, What about the gen1 SPI devices like the F4 ? It should have been better to use SoC specific compatible, or specify the SPI HW gen like gen1 or gen2. Neil > +- reg: Offset and length of the device's register set. > +- interrupts: Must contain the interrupt id. > +- clocks: Must contain an entry for spiclk (which feeds the internal clock > + generator). > +- #address-cells: Number of cells required to define a chip select address. > +- #size-cells: Should be zero. > + > +Optional properties: > +- resets: Must contain the phandle to the reset controller. > +- A pinctrl state named "default" may be defined to set pins in mode of > + operation for SPI transfer. > +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the > + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. > +- dma-names: DMA request names should include "tx" and "rx" if present. > +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, > + Documentation/devicetree/bindings/spi/spi-bus.txt > + > + > +Child nodes represent devices on the SPI bus > + See ../spi/spi-bus.txt > + > +Optional properties: > +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in > + nanoseconds inserted between two consecutive data frames. > + > + > +Example: > + spi2: spi@40003800 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-spi"; > + reg = <0x40003800 0x400>; > + interrupts = <36>; > + clocks = <&rcc SPI2_CK>; > + resets = <&rcc 1166>; > + dmas = <&dmamux1 0 39 0x400 0x01>, > + <&dmamux1 1 40 0x400 0x01>; > + dma-names = "rx", "tx"; > + pinctrl-0 = <&spi2_pins_b>; > + pinctrl-names = "default"; > + status = "okay"; > + cs-gpios = <&gpioa 11 0>; > + > + spidev@0 { > + compatible = "spidev"; > + reg = <0>; > + spi-max-frequency = <4000000>; > + st,spi-midi = <4000>; > + }; > + }; > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 06/21/2017 05:20 PM, Neil Armstrong wrote: > On 06/21/2017 04:32 PM, Amelie Delaunay wrote: >> This patch adds the documentation of device tree bindings >> for the STM32 SPI controller. >> >> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> >> --- >> .../devicetree/bindings/spi/spi-stm32.txt | 60 ++++++++++++++++++++++ >> 1 file changed, 60 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt >> >> diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt >> new file mode 100644 >> index 0000000..3958bf6 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt >> @@ -0,0 +1,60 @@ >> +STMicroelectronics STM32 SPI Controller >> + >> +The STM32 SPI controller is used to communicate with external devices using >> +the Serial Peripheral Interface. It supports full-duplex, half-duplex and >> +simplex synchronous serial communication with external devices. It supports >> +from 4 to 32-bit data size. Although it can be configured as master or slave, >> +only master is supported by the driver. >> + >> +Required properties: >> +- compatible: Must be "st,stm32-spi". > > Hi Amelie, > > What about the gen1 SPI devices like the F4 ? > > It should have been better to use SoC specific compatible, or specify the SPI HW gen like gen1 or gen2. > > Neil > Hi Neil, The gen1 SPI controller embedded on F4/F7 is different from gen2 embedded on H7 and just to illustrate this, there are 5 main registers (16-bit) on gen1 versus 10 main registers on gen2 (32-bit)! Their operating modes are different, fifo management and so on... Moreover, I know that the community is working on an SPI driver for F4. I agree with you on the fact that it would be better to use a SoC specific compatible: I will send a v2 with "st,stm32h7-spi". This way, this will be aligned with what have been done for the I2S part of this controller: https://patchwork.kernel.org/patch/9737799/ By the way, I also noticed that my optional property "st,spi-midi-ns" doesn't fit with the example "st,spi-midi". I will fix that in the v2 and keep "st,spi-midi-ns". Regards, Amelie >> +- reg: Offset and length of the device's register set. >> +- interrupts: Must contain the interrupt id. >> +- clocks: Must contain an entry for spiclk (which feeds the internal clock >> + generator). >> +- #address-cells: Number of cells required to define a chip select address. >> +- #size-cells: Should be zero. >> + >> +Optional properties: >> +- resets: Must contain the phandle to the reset controller. >> +- A pinctrl state named "default" may be defined to set pins in mode of >> + operation for SPI transfer. >> +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the >> + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. >> +- dma-names: DMA request names should include "tx" and "rx" if present. >> +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, >> + Documentation/devicetree/bindings/spi/spi-bus.txt >> + >> + >> +Child nodes represent devices on the SPI bus >> + See ../spi/spi-bus.txt >> + >> +Optional properties: >> +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in >> + nanoseconds inserted between two consecutive data frames. >> + >> + >> +Example: >> + spi2: spi@40003800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-spi"; >> + reg = <0x40003800 0x400>; >> + interrupts = <36>; >> + clocks = <&rcc SPI2_CK>; >> + resets = <&rcc 1166>; >> + dmas = <&dmamux1 0 39 0x400 0x01>, >> + <&dmamux1 1 40 0x400 0x01>; >> + dma-names = "rx", "tx"; >> + pinctrl-0 = <&spi2_pins_b>; >> + pinctrl-names = "default"; >> + status = "okay"; >> + cs-gpios = <&gpioa 11 0>; >> + >> + spidev@0 { >> + compatible = "spidev"; >> + reg = <0>; >> + spi-max-frequency = <4000000>; >> + st,spi-midi = <4000>; >> + }; >> + }; >> > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, Jun 21, 2017 at 04:32:05PM +0200, Amelie Delaunay wrote: > This patch adds the documentation of device tree bindings > for the STM32 SPI controller. > > Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> > --- > .../devicetree/bindings/spi/spi-stm32.txt | 60 ++++++++++++++++++++++ > 1 file changed, 60 insertions(+) > create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt > > diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt > new file mode 100644 > index 0000000..3958bf6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt > @@ -0,0 +1,60 @@ > +STMicroelectronics STM32 SPI Controller > + > +The STM32 SPI controller is used to communicate with external devices using > +the Serial Peripheral Interface. It supports full-duplex, half-duplex and > +simplex synchronous serial communication with external devices. It supports > +from 4 to 32-bit data size. Although it can be configured as master or slave, > +only master is supported by the driver. > + > +Required properties: > +- compatible: Must be "st,stm32-spi". > +- reg: Offset and length of the device's register set. > +- interrupts: Must contain the interrupt id. > +- clocks: Must contain an entry for spiclk (which feeds the internal clock > + generator). > +- #address-cells: Number of cells required to define a chip select address. > +- #size-cells: Should be zero. > + > +Optional properties: > +- resets: Must contain the phandle to the reset controller. > +- A pinctrl state named "default" may be defined to set pins in mode of > + operation for SPI transfer. > +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the > + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. > +- dma-names: DMA request names should include "tx" and "rx" if present. > +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, > + Documentation/devicetree/bindings/spi/spi-bus.txt > + > + > +Child nodes represent devices on the SPI bus > + See ../spi/spi-bus.txt > + > +Optional properties: > +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in > + nanoseconds inserted between two consecutive data frames. > + > + > +Example: > + spi2: spi@40003800 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "st,stm32-spi"; > + reg = <0x40003800 0x400>; > + interrupts = <36>; > + clocks = <&rcc SPI2_CK>; > + resets = <&rcc 1166>; > + dmas = <&dmamux1 0 39 0x400 0x01>, > + <&dmamux1 1 40 0x400 0x01>; > + dma-names = "rx", "tx"; > + pinctrl-0 = <&spi2_pins_b>; > + pinctrl-names = "default"; > + status = "okay"; Don't show status in examples. > + cs-gpios = <&gpioa 11 0>; > + > + spidev@0 { > + compatible = "spidev"; This is not a valid compatible. Pick a real device. Rob -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, On 06/26/2017 08:21 PM, Rob Herring wrote: > On Wed, Jun 21, 2017 at 04:32:05PM +0200, Amelie Delaunay wrote: >> This patch adds the documentation of device tree bindings >> for the STM32 SPI controller. >> >> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> >> --- >> .../devicetree/bindings/spi/spi-stm32.txt | 60 ++++++++++++++++++++++ >> 1 file changed, 60 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt >> >> diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt >> new file mode 100644 >> index 0000000..3958bf6 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt >> @@ -0,0 +1,60 @@ >> +STMicroelectronics STM32 SPI Controller >> + >> +The STM32 SPI controller is used to communicate with external devices using >> +the Serial Peripheral Interface. It supports full-duplex, half-duplex and >> +simplex synchronous serial communication with external devices. It supports >> +from 4 to 32-bit data size. Although it can be configured as master or slave, >> +only master is supported by the driver. >> + >> +Required properties: >> +- compatible: Must be "st,stm32-spi". >> +- reg: Offset and length of the device's register set. >> +- interrupts: Must contain the interrupt id. >> +- clocks: Must contain an entry for spiclk (which feeds the internal clock >> + generator). >> +- #address-cells: Number of cells required to define a chip select address. >> +- #size-cells: Should be zero. >> + >> +Optional properties: >> +- resets: Must contain the phandle to the reset controller. >> +- A pinctrl state named "default" may be defined to set pins in mode of >> + operation for SPI transfer. >> +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the >> + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. >> +- dma-names: DMA request names should include "tx" and "rx" if present. >> +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, >> + Documentation/devicetree/bindings/spi/spi-bus.txt >> + >> + >> +Child nodes represent devices on the SPI bus >> + See ../spi/spi-bus.txt >> + >> +Optional properties: >> +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in >> + nanoseconds inserted between two consecutive data frames. >> + >> + >> +Example: >> + spi2: spi@40003800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-spi"; >> + reg = <0x40003800 0x400>; >> + interrupts = <36>; >> + clocks = <&rcc SPI2_CK>; >> + resets = <&rcc 1166>; >> + dmas = <&dmamux1 0 39 0x400 0x01>, >> + <&dmamux1 1 40 0x400 0x01>; >> + dma-names = "rx", "tx"; >> + pinctrl-0 = <&spi2_pins_b>; >> + pinctrl-names = "default"; >> + status = "okay"; > > Don't show status in examples. > Ok. >> + cs-gpios = <&gpioa 11 0>; >> + >> + spidev@0 { >> + compatible = "spidev"; > > This is not a valid compatible. Pick a real device. Ok this was just to illustrate the optional property st,spi-midi-ns. > > Rob > I will send a new patch to fix these issues. Thanks, Amelie -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt new file mode 100644 index 0000000..3958bf6 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt @@ -0,0 +1,60 @@ +STMicroelectronics STM32 SPI Controller + +The STM32 SPI controller is used to communicate with external devices using +the Serial Peripheral Interface. It supports full-duplex, half-duplex and +simplex synchronous serial communication with external devices. It supports +from 4 to 32-bit data size. Although it can be configured as master or slave, +only master is supported by the driver. + +Required properties: +- compatible: Must be "st,stm32-spi". +- reg: Offset and length of the device's register set. +- interrupts: Must contain the interrupt id. +- clocks: Must contain an entry for spiclk (which feeds the internal clock + generator). +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- resets: Must contain the phandle to the reset controller. +- A pinctrl state named "default" may be defined to set pins in mode of + operation for SPI transfer. +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. +- dma-names: DMA request names should include "tx" and "rx" if present. +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Optional properties: +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in + nanoseconds inserted between two consecutive data frames. + + +Example: + spi2: spi@40003800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-spi"; + reg = <0x40003800 0x400>; + interrupts = <36>; + clocks = <&rcc SPI2_CK>; + resets = <&rcc 1166>; + dmas = <&dmamux1 0 39 0x400 0x01>, + <&dmamux1 1 40 0x400 0x01>; + dma-names = "rx", "tx"; + pinctrl-0 = <&spi2_pins_b>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&gpioa 11 0>; + + spidev@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <4000000>; + st,spi-midi = <4000>; + }; + };
This patch adds the documentation of device tree bindings for the STM32 SPI controller. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> --- .../devicetree/bindings/spi/spi-stm32.txt | 60 ++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32.txt