| Message ID | 1497601068-181656-1-git-send-email-shawn.lin@rock-chips.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Kishon, On 2017/6/16 16:17, Shawn Lin wrote: > phy_mode was added for switching USB mode purposely as > well as phy_set_mode API. However other types of PHY could > also have some miscellaneous setting/modes need to be > handled. This patch is gonna support this callback for > phy-rockchip-pcie and do some power-saving work there. > Note that we just stuff in some other values other that the > existing phy_mode and convert it in the coressponding driver > instead, otherwise we should extend the phy_mode again which > it doesn't make sense to add in new driver's specificed value. > Overall it looks fine to me as the controller's driver and the > phy's driver are paired so that the caller and the consumer should > be able to keep the value(mode) in consistent. > Any chance for you to have a look at this patch? :) > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > --- > > drivers/phy/rockchip/phy-rockchip-pcie.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/drivers/phy/rockchip/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c > index 6904633..9ffad15 100644 > --- a/drivers/phy/rockchip/phy-rockchip-pcie.c > +++ b/drivers/phy/rockchip/phy-rockchip-pcie.c > @@ -255,11 +255,33 @@ static int rockchip_pcie_phy_exit(struct phy *phy) > return 0; > } > > +static int rockchip_pcie_phy_set_mode(struct phy *phy, enum phy_mode mode) > +{ > + struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy); > + u8 map = (u8)mode; > + int i; > + > + for (i = 0; i < PHY_MAX_LANE_NUM; i++) { > + if (map & BIT(i)) > + continue; > + > + dev_dbg(&phy->dev, "idling lane %d\n", i); > + regmap_write(rk_phy->reg_base, > + rk_phy->phy_data->pcie_laneoff, > + HIWORD_UPDATE(PHY_LANE_IDLE_OFF, > + PHY_LANE_IDLE_MASK, > + PHY_LANE_IDLE_A_SHIFT + i)); > + } > + > + return 0; > +} > + > static const struct phy_ops ops = { > .init = rockchip_pcie_phy_init, > .exit = rockchip_pcie_phy_exit, > .power_on = rockchip_pcie_phy_power_on, > .power_off = rockchip_pcie_phy_power_off, > + .set_mode = rockchip_pcie_phy_set_mode, > .owner = THIS_MODULE, > }; > >
On Fri, Jun 16, 2017 at 04:17:47PM +0800, Shawn Lin wrote: > phy_mode was added for switching USB mode purposely as > well as phy_set_mode API. However other types of PHY could > also have some miscellaneous setting/modes need to be > handled. This patch is gonna support this callback for > phy-rockchip-pcie and do some power-saving work there. > Note that we just stuff in some other values other that the > existing phy_mode and convert it in the coressponding driver > instead, otherwise we should extend the phy_mode again which > it doesn't make sense to add in new driver's specificed value. > Overall it looks fine to me as the controller's driver and the > phy's driver are paired so that the caller and the consumer should > be able to keep the value(mode) in consistent. s/coressponding/corresponding/ s/specificed/specified/ s/in consistent/consistent/ > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > --- > > drivers/phy/rockchip/phy-rockchip-pcie.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/drivers/phy/rockchip/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c > index 6904633..9ffad15 100644 > --- a/drivers/phy/rockchip/phy-rockchip-pcie.c > +++ b/drivers/phy/rockchip/phy-rockchip-pcie.c > @@ -255,11 +255,33 @@ static int rockchip_pcie_phy_exit(struct phy *phy) > return 0; > } > > +static int rockchip_pcie_phy_set_mode(struct phy *phy, enum phy_mode mode) > +{ > + struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy); > + u8 map = (u8)mode; > + int i; > + > + for (i = 0; i < PHY_MAX_LANE_NUM; i++) { > + if (map & BIT(i)) > + continue; phy_mode is defined as: enum phy_mode { PHY_MODE_INVALID, PHY_MODE_USB_HOST, PHY_MODE_USB_DEVICE, PHY_MODE_USB_OTG, }; You're using phy_mode as something entirely different -- a bitmap of which lanes you want to keep active. I understand you're trying to avoid extending phy_mode again, but I just want to point out that there are no other places that subvert phy_mode as you're doing. It's probably worth a comment here about why we're not using the standard enum values. I see you already have one at the caller. I'm not the PHY guy, so I'd like Kishon's ack before going down this road. > + > + dev_dbg(&phy->dev, "idling lane %d\n", i); > + regmap_write(rk_phy->reg_base, > + rk_phy->phy_data->pcie_laneoff, > + HIWORD_UPDATE(PHY_LANE_IDLE_OFF, > + PHY_LANE_IDLE_MASK, > + PHY_LANE_IDLE_A_SHIFT + i)); > + } > + > + return 0; > +} > + > static const struct phy_ops ops = { > .init = rockchip_pcie_phy_init, > .exit = rockchip_pcie_phy_exit, > .power_on = rockchip_pcie_phy_power_on, > .power_off = rockchip_pcie_phy_power_off, > + .set_mode = rockchip_pcie_phy_set_mode, > .owner = THIS_MODULE, > }; > > -- > 1.9.1 > >
Hi, On Friday 16 June 2017 01:47 PM, Shawn Lin wrote: > phy_mode was added for switching USB mode purposely as > well as phy_set_mode API. However other types of PHY could > also have some miscellaneous setting/modes need to be > handled. This patch is gonna support this callback for > phy-rockchip-pcie and do some power-saving work there. > Note that we just stuff in some other values other that the > existing phy_mode and convert it in the coressponding driver > instead, otherwise we should extend the phy_mode again which > it doesn't make sense to add in new driver's specificed value. > Overall it looks fine to me as the controller's driver and the > phy's driver are paired so that the caller and the consumer should > be able to keep the value(mode) in consistent. I really don't prefer using an API other that what it is intended for. We have to come up with a better way for handling this. IIUC this patch sets unused lanes in idle mode? If yes, then can't we model each lane as a separate phy, so that we can power-on/power-off each lane independently. Thanks Kishon > > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > --- > > drivers/phy/rockchip/phy-rockchip-pcie.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/drivers/phy/rockchip/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c > index 6904633..9ffad15 100644 > --- a/drivers/phy/rockchip/phy-rockchip-pcie.c > +++ b/drivers/phy/rockchip/phy-rockchip-pcie.c > @@ -255,11 +255,33 @@ static int rockchip_pcie_phy_exit(struct phy *phy) > return 0; > } > > +static int rockchip_pcie_phy_set_mode(struct phy *phy, enum phy_mode mode) > +{ > + struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy); > + u8 map = (u8)mode; > + int i; > + > + for (i = 0; i < PHY_MAX_LANE_NUM; i++) { > + if (map & BIT(i)) > + continue; > + > + dev_dbg(&phy->dev, "idling lane %d\n", i); > + regmap_write(rk_phy->reg_base, > + rk_phy->phy_data->pcie_laneoff, > + HIWORD_UPDATE(PHY_LANE_IDLE_OFF, > + PHY_LANE_IDLE_MASK, > + PHY_LANE_IDLE_A_SHIFT + i)); > + } > + > + return 0; > +} > + > static const struct phy_ops ops = { > .init = rockchip_pcie_phy_init, > .exit = rockchip_pcie_phy_exit, > .power_on = rockchip_pcie_phy_power_on, > .power_off = rockchip_pcie_phy_power_off, > + .set_mode = rockchip_pcie_phy_set_mode, > .owner = THIS_MODULE, > }; > >
Hi Kishon, On Mon, Jul 10, 2017 at 9:45 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote: > On Friday 16 June 2017 01:47 PM, Shawn Lin wrote: > > phy_mode was added for switching USB mode purposely as > > well as phy_set_mode API. However other types of PHY could > > also have some miscellaneous setting/modes need to be > > handled. This patch is gonna support this callback for > > phy-rockchip-pcie and do some power-saving work there. > > Note that we just stuff in some other values other that the > > existing phy_mode and convert it in the coressponding driver > > instead, otherwise we should extend the phy_mode again which > > it doesn't make sense to add in new driver's specificed value. > > Overall it looks fine to me as the controller's driver and the > > phy's driver are paired so that the caller and the consumer should > > be able to keep the value(mode) in consistent. > > I really don't prefer using an API other that what it is intended for. We have > to come up with a better way for handling this. > > IIUC this patch sets unused lanes in idle mode? If yes, then can't we model > each lane as a separate phy, so that we can power-on/power-off each lane > independently. I suggested the same to Shawn previously. I'm interested in seeing his response. But personally I'm still not sure if that's the most accurate way to describe this PHY, except for the fact that inevitably, most device tree bindings get molded to match the related kernel APIs, rather than the other way around. What if instead, we added an enum mode entry that represents "finished link training", at which point the PHY would then know it can power down the unused lanes (that's assuming the PHY can figure that part out)? Or if we did re-model this PHY, how are we supposed to handle backward compatibility? Can the same PHY driver support 2 different of_xlate methods? I guess we'd have to provide an implementation that sets the driver up to behave completely differently based on the number of #phy-cells? Brian
Hi Kishon, On 2017/7/11 12:45, Kishon Vijay Abraham I wrote: > Hi, > > On Friday 16 June 2017 01:47 PM, Shawn Lin wrote: >> phy_mode was added for switching USB mode purposely as >> well as phy_set_mode API. However other types of PHY could >> also have some miscellaneous setting/modes need to be >> handled. This patch is gonna support this callback for >> phy-rockchip-pcie and do some power-saving work there. >> Note that we just stuff in some other values other that the >> existing phy_mode and convert it in the coressponding driver >> instead, otherwise we should extend the phy_mode again which >> it doesn't make sense to add in new driver's specificed value. >> Overall it looks fine to me as the controller's driver and the >> phy's driver are paired so that the caller and the consumer should >> be able to keep the value(mode) in consistent. > > I really don't prefer using an API other that what it is intended for. We have > to come up with a better way for handling this. okay. > > IIUC this patch sets unused lanes in idle mode? If yes, then can't we model > each lane as a separate phy, so that we can power-on/power-off each lane > independently. I will have a try and see how far I will go. Thanks. > > Thanks > Kishon >> >> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> >> --- >> >> drivers/phy/rockchip/phy-rockchip-pcie.c | 22 ++++++++++++++++++++++ >> 1 file changed, 22 insertions(+) >> >> diff --git a/drivers/phy/rockchip/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c >> index 6904633..9ffad15 100644 >> --- a/drivers/phy/rockchip/phy-rockchip-pcie.c >> +++ b/drivers/phy/rockchip/phy-rockchip-pcie.c >> @@ -255,11 +255,33 @@ static int rockchip_pcie_phy_exit(struct phy *phy) >> return 0; >> } >> >> +static int rockchip_pcie_phy_set_mode(struct phy *phy, enum phy_mode mode) >> +{ >> + struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy); >> + u8 map = (u8)mode; >> + int i; >> + >> + for (i = 0; i < PHY_MAX_LANE_NUM; i++) { >> + if (map & BIT(i)) >> + continue; >> + >> + dev_dbg(&phy->dev, "idling lane %d\n", i); >> + regmap_write(rk_phy->reg_base, >> + rk_phy->phy_data->pcie_laneoff, >> + HIWORD_UPDATE(PHY_LANE_IDLE_OFF, >> + PHY_LANE_IDLE_MASK, >> + PHY_LANE_IDLE_A_SHIFT + i)); >> + } >> + >> + return 0; >> +} >> + >> static const struct phy_ops ops = { >> .init = rockchip_pcie_phy_init, >> .exit = rockchip_pcie_phy_exit, >> .power_on = rockchip_pcie_phy_power_on, >> .power_off = rockchip_pcie_phy_power_off, >> + .set_mode = rockchip_pcie_phy_set_mode, >> .owner = THIS_MODULE, >> }; >> >> > > >
On Mon, Jul 10, 2017 at 10:20:32PM -0700, Brian Norris wrote: > Hi Kishon, Hi again Kishon, I didn't get a response from you, but Shawn is continuing to send several versions of a patchset implementing one of these suggestions. I'd like to ping back here, in the hopes of getting an answer. > On Mon, Jul 10, 2017 at 9:45 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote: > > On Friday 16 June 2017 01:47 PM, Shawn Lin wrote: > > > phy_mode was added for switching USB mode purposely as > > > well as phy_set_mode API. However other types of PHY could > > > also have some miscellaneous setting/modes need to be > > > handled. This patch is gonna support this callback for > > > phy-rockchip-pcie and do some power-saving work there. > > > Note that we just stuff in some other values other that the > > > existing phy_mode and convert it in the coressponding driver > > > instead, otherwise we should extend the phy_mode again which > > > it doesn't make sense to add in new driver's specificed value. > > > Overall it looks fine to me as the controller's driver and the > > > phy's driver are paired so that the caller and the consumer should > > > be able to keep the value(mode) in consistent. > > > > I really don't prefer using an API other that what it is intended for. We have > > to come up with a better way for handling this. > > > > IIUC this patch sets unused lanes in idle mode? If yes, then can't we model > > each lane as a separate phy, so that we can power-on/power-off each lane > > independently. > > I suggested the same to Shawn previously. I'm interested in seeing his response. Judging by Shawn's subsequent patches, I guess he saw no problem with this. I'm still not so sure. > But personally I'm still not sure if that's the most accurate way to > describe this PHY, except for the fact that inevitably, most device > tree bindings get molded to match the related kernel APIs, rather than > the other way around. What if instead, we added an enum mode entry > that represents "finished link training", at which point the PHY would > then know it can power down the unused lanes (that's assuming the PHY > can figure that part out)? Can I get an answer here? Is it possible that we extend the PHY API with either a new 'phy_mode', or with some other PCIe-specific extension? As I said above, it doesn't actually seem like a natural description of the hardware to say that there are 4 PHYs here, instead of just 1. And then it puts more burden on the provider/consumer drivers to do a lot of weird accounting, just so that this single piece of hardware can fit the current limited set of APIs. This is not the first time that some concept isn't so easy to fit into the existing framework. I think it would be prudent to consider ways to better extend the API to support modes specific to device classes. You've already done that for some USB pieces, and I think it would make sense to extend this to PCIe. For instance, we could have the PHY export things like "number of PCIe lanes", and support callbacks for "disable unused lanes". > Or if we did re-model this PHY, how are we supposed to handle backward > compatibility? Can the same PHY driver support 2 different of_xlate > methods? I guess we'd have to provide an implementation that sets the > driver up to behave completely differently based on the number of > #phy-cells? I guess Shawn was able to work out some of this. But all the extra state-tracking and reference counting appears to be hard to get right... Brian
diff --git a/drivers/phy/rockchip/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c index 6904633..9ffad15 100644 --- a/drivers/phy/rockchip/phy-rockchip-pcie.c +++ b/drivers/phy/rockchip/phy-rockchip-pcie.c @@ -255,11 +255,33 @@ static int rockchip_pcie_phy_exit(struct phy *phy) return 0; } +static int rockchip_pcie_phy_set_mode(struct phy *phy, enum phy_mode mode) +{ + struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy); + u8 map = (u8)mode; + int i; + + for (i = 0; i < PHY_MAX_LANE_NUM; i++) { + if (map & BIT(i)) + continue; + + dev_dbg(&phy->dev, "idling lane %d\n", i); + regmap_write(rk_phy->reg_base, + rk_phy->phy_data->pcie_laneoff, + HIWORD_UPDATE(PHY_LANE_IDLE_OFF, + PHY_LANE_IDLE_MASK, + PHY_LANE_IDLE_A_SHIFT + i)); + } + + return 0; +} + static const struct phy_ops ops = { .init = rockchip_pcie_phy_init, .exit = rockchip_pcie_phy_exit, .power_on = rockchip_pcie_phy_power_on, .power_off = rockchip_pcie_phy_power_off, + .set_mode = rockchip_pcie_phy_set_mode, .owner = THIS_MODULE, };
phy_mode was added for switching USB mode purposely as well as phy_set_mode API. However other types of PHY could also have some miscellaneous setting/modes need to be handled. This patch is gonna support this callback for phy-rockchip-pcie and do some power-saving work there. Note that we just stuff in some other values other that the existing phy_mode and convert it in the coressponding driver instead, otherwise we should extend the phy_mode again which it doesn't make sense to add in new driver's specificed value. Overall it looks fine to me as the controller's driver and the phy's driver are paired so that the caller and the consumer should be able to keep the value(mode) in consistent. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> --- drivers/phy/rockchip/phy-rockchip-pcie.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)