| Message ID | 1309879568-25837-4-git-send-email-shawn.guo@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Jul 05, 2011 at 11:54:34AM -0600, Grant Likely wrote: > On Tue, Jul 5, 2011 at 9:26 AM, Shawn Guo <shawn.guo@linaro.org> wrote: > > The patch adds device tree probe support for sdhci-esdhc-imx driver. > > > > Signed-off-by: Shawn Guo <shawn.guo@linaro.org> > > Cc: Wolfram Sang <w.sang@pengutronix.de> > > Cc: Chris Ball <cjb@laptop.org> > > Cc: Grant Likely <grant.likely@secretlab.ca> > > --- > > .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 40 ++++++++ > > drivers/mmc/host/sdhci-esdhc-imx.c | 102 +++++++++++++++++++- > > 2 files changed, 137 insertions(+), 5 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > > > diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > new file mode 100644 > > index 0000000..351d239 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > @@ -0,0 +1,40 @@ > > +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX > > + > > +The Enhanced Secure Digital Host Controller on Freescale i.MX family > > +provides an interface for MMC, SD, and SDIO types of memory cards. > > + > > +Required properties: > > +- compatible : Should be "fsl,<chip>-esdhc" > > +- reg : Should contain eSDHC registers location and length > > +- interrupts : Should contain eSDHC interrupt > > +- cd-type : String, card detection (CD) method. Supported values are: > > + "none" : No CD > > + "controller" : Uses eSDHC controller internal CD signal > > + "gpio" : Uses GPIO pin for CD > > + "permanent" : No CD because card is permanently wired to host > > +- wp-type : String, write protection (WP) method. Supported values are: > > + "none" : No WP > > + "controller" : Uses eSDHC controller internal WP signal > > + "gpio" : Uses GPIO pin for WP > > +- gpios : Should specify GPIOs in this order: CD GPIO, WP GPIO, if > > + properties cd-type and wp-type are "gpio". > > Again, be explicit in your gpios property names. Create a different > property for each gpio: cd-gpios and wp-gpios. > Sorry. I fixed the example below. But this one got missed. > As for wp-type and cd-type, I think you can drop them. Default to > internal controller CD and WP pins. Use gpio if cd-gpios or wp-gpios > is present, and define specific properties for the no-wp, no-cd and > fixed-card cases. (can you tell that I'm not a fan of the "*-type" > binding for this driver?) :-) > Ok, I'm getting to know you. > > + > > +Examples: > > + > > +esdhc@70004000 { > > + compatible = "fsl,imx51-esdhc"; > > + reg = <0x70004000 0x4000>; > > + interrupts = <1>; > > + fsl,cd-type = "controller"; > > + fsl,wp-type = "controller"; > > +}; > > + > > +esdhc@70008000 { > > + compatible = "fsl,imx51-esdhc"; > > + reg = <0x70008000 0x4000>; > > + interrupts = <2>; > > + fsl,cd-type = "gpio"; > > + fsl,wp-type = "gpio"; > > + cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ > > + wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ > > +}; > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c > > index 1edda29..593d6b9 100644 > > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > > @@ -20,6 +20,9 @@ > > #include <linux/mmc/host.h> > > #include <linux/mmc/mmc.h> > > #include <linux/mmc/sdio.h> > > +#include <linux/of.h> > > +#include <linux/of_device.h> > > +#include <linux/of_gpio.h> > > #include <mach/esdhc.h> > > #include "sdhci-pltfm.h" > > #include "sdhci-esdhc.h" > > @@ -72,6 +75,14 @@ static struct platform_device_id imx_esdhc_devtype[] = { > > } > > }; > > > > +static const struct of_device_id imx_esdhc_dt_ids[] = { > > + { .compatible = "fsl,imx25-esdhc", .data = &imx_esdhc_devtype[IMX25_ESDHC], }, > > + { .compatible = "fsl,imx35-esdhc", .data = &imx_esdhc_devtype[IMX35_ESDHC], }, > > + { .compatible = "fsl,imx51-esdhc", .data = &imx_esdhc_devtype[IMX51_ESDHC], }, > > + { .compatible = "fsl,imx53-esdhc", .data = &imx_esdhc_devtype[IMX53_ESDHC], }, > > + { /* sentinel */ } > > +}; > > + > > static inline int is_imx25_esdhc(struct pltfm_imx_data *data) > > { > > return data->devtype == IMX25_ESDHC; > > @@ -305,24 +316,96 @@ static irqreturn_t cd_irq(int irq, void *data) > > return IRQ_HANDLED; > > }; > > > > +#ifdef CONFIG_OF > > +static const char *cd_types[] = { > > + [ESDHC_CD_NONE] = "none", > > + [ESDHC_CD_CONTROLLER] = "controller", > > + [ESDHC_CD_GPIO] = "gpio", > > + [ESDHC_CD_PERMANENT] = "permanent", > > +}; > > + > > +static const char *wp_types[] = { > > + [ESDHC_WP_NONE] = "none", > > + [ESDHC_WP_CONTROLLER] = "controller", > > + [ESDHC_WP_GPIO] = "gpio", > > +}; > > + > > +static int __devinit sdhci_esdhc_imx_probe_dt(struct platform_device *pdev) > > +{ > > + const struct of_device_id *of_id = > > + of_match_device(imx_esdhc_dt_ids, &pdev->dev); > > + struct device_node *np = pdev->dev.of_node; > > + struct esdhc_platform_data *boarddata; > > + int err, i; > > + const char *cd, *wp; > > + > > + if (!np) > > + return -ENODEV; > > + > > + boarddata = kzalloc(sizeof(*boarddata), GFP_KERNEL); > > + if (!boarddata) > > + return -ENOMEM; > > + pdev->dev.platform_data = boarddata; > > This is illegal. As far as device drivers are concerned, > pdev->dev.platform_data is immutable and must not be changed. > Otherwise they break the driver model. If you need to keep around a > platform_data structure, then it needs to be stored in the driver > private data. Your best option is to refactor the driver to not > reference pdev->dev.platform_data after probe() exits. > Ok. I saw a patch from Troy doing this. Will incorporate it into the series. Regards, Shawn > > + > > + err = of_property_read_string(np, "fsl,cd-type", &cd); > > + if (err) > > + return err; > > + for (i = 0; i < ARRAY_SIZE(cd_types); i++) > > + if (!strcasecmp(cd, cd_types[i])) { > > + boarddata->cd_type = i; > > + break; > > + } > > + > > + err = of_property_read_string(np, "fsl,wp-type", &wp); > > + if (err) > > + return err; > > + for (i = 0; i < ARRAY_SIZE(wp_types); i++) > > + if (!strcasecmp(wp, wp_types[i])) { > > + boarddata->wp_type = i; > > + break; > > + } > > + > > + boarddata->cd_gpio = of_get_gpio(np, 0); > > + boarddata->wp_gpio = of_get_gpio(np, 1); > > + > > + pdev->id_entry = of_id->data; > > + > > + return 0; > > +} > > +#else > > +static inline int sdhci_esdhc_imx_probe_dt(struct platform_device *pdev) > > +{ > > + return 0; > > +} > > +#endif > > + > > static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) > > { > > + struct device_node *np = pdev->dev.of_node; > > struct sdhci_pltfm_host *pltfm_host; > > struct sdhci_host *host; > > - struct esdhc_platform_data *boarddata; > > + struct esdhc_platform_data *boarddata = NULL; > > struct clk *clk; > > int err; > > struct pltfm_imx_data *imx_data; > > > > + err = sdhci_esdhc_imx_probe_dt(pdev); > > + if (err) > > + return err; > > + > > host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata); > > - if (IS_ERR(host)) > > - return PTR_ERR(host); > > + if (IS_ERR(host)) { > > + err = PTR_ERR(host); > > + goto err_sdhci_pltfm; > > + } > > > > pltfm_host = sdhci_priv(host); > > > > imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL); > > - if (!imx_data) > > - return -ENOMEM; > > + if (!imx_data) { > > + err = -ENOMEM; > > + goto err_imx_data; > > + } > > > > imx_data->devtype = pdev->id_entry->driver_data; > > pltfm_host->priv = imx_data; > > @@ -416,12 +499,17 @@ no_board_data: > > clk_put(pltfm_host->clk); > > err_clk_get: > > kfree(imx_data); > > +err_imx_data: > > sdhci_pltfm_free(pdev); > > +err_sdhci_pltfm: > > + if (np) > > + kfree(boarddata); > > return err; > > } > > > > static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) > > { > > + struct device_node *np = pdev->dev.of_node; > > struct sdhci_host *host = platform_get_drvdata(pdev); > > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > > struct esdhc_platform_data *boarddata = host->mmc->parent->platform_data; > > @@ -444,6 +532,9 @@ static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) > > > > sdhci_pltfm_free(pdev); > > > > + if (np) > > + kfree(boarddata); > > + > > return 0; > > } > > > > @@ -451,6 +542,7 @@ static struct platform_driver sdhci_esdhc_imx_driver = { > > .driver = { > > .name = "sdhci-esdhc-imx", > > .owner = THIS_MODULE, > > + .of_match_table = imx_esdhc_dt_ids, > > }, > > .id_table = imx_esdhc_devtype, > > .probe = sdhci_esdhc_imx_probe, > > -- > > 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Jul 05, 2011 at 11:54:34AM -0600, Grant Likely wrote: > On Tue, Jul 5, 2011 at 9:26 AM, Shawn Guo <shawn.guo@linaro.org> wrote: > > The patch adds device tree probe support for sdhci-esdhc-imx driver. > > > > Signed-off-by: Shawn Guo <shawn.guo@linaro.org> > > Cc: Wolfram Sang <w.sang@pengutronix.de> > > Cc: Chris Ball <cjb@laptop.org> > > Cc: Grant Likely <grant.likely@secretlab.ca> > > --- > > .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 40 ++++++++ > > drivers/mmc/host/sdhci-esdhc-imx.c | 102 +++++++++++++++++++- > > 2 files changed, 137 insertions(+), 5 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > > > diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > new file mode 100644 > > index 0000000..351d239 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > @@ -0,0 +1,40 @@ > > +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX > > + > > +The Enhanced Secure Digital Host Controller on Freescale i.MX family > > +provides an interface for MMC, SD, and SDIO types of memory cards. > > + > > +Required properties: > > +- compatible : Should be "fsl,<chip>-esdhc" > > +- reg : Should contain eSDHC registers location and length > > +- interrupts : Should contain eSDHC interrupt > > +- cd-type : String, card detection (CD) method. Supported values are: > > + "none" : No CD > > + "controller" : Uses eSDHC controller internal CD signal > > + "gpio" : Uses GPIO pin for CD > > + "permanent" : No CD because card is permanently wired to host > > +- wp-type : String, write protection (WP) method. Supported values are: > > + "none" : No WP > > + "controller" : Uses eSDHC controller internal WP signal > > + "gpio" : Uses GPIO pin for WP > > +- gpios : Should specify GPIOs in this order: CD GPIO, WP GPIO, if > > + properties cd-type and wp-type are "gpio". > > Again, be explicit in your gpios property names. Create a different > property for each gpio: cd-gpios and wp-gpios. > > As for wp-type and cd-type, I think you can drop them. Default to > internal controller CD and WP pins. Use gpio if cd-gpios or wp-gpios > is present, and define specific properties for the no-wp, no-cd and > fixed-card cases. (can you tell that I'm not a fan of the "*-type" > binding for this driver?) :-) > I would let default be no CD/WP, and define properties for controller internal CD/WP and wired case, if you do not see a problem with it.
On Wed, Jul 06, 2011 at 11:43:15PM +0800, Shawn Guo wrote: > On Tue, Jul 05, 2011 at 11:54:34AM -0600, Grant Likely wrote: > > On Tue, Jul 5, 2011 at 9:26 AM, Shawn Guo <shawn.guo@linaro.org> wrote: > > > The patch adds device tree probe support for sdhci-esdhc-imx driver. > > > > > > Signed-off-by: Shawn Guo <shawn.guo@linaro.org> > > > Cc: Wolfram Sang <w.sang@pengutronix.de> > > > Cc: Chris Ball <cjb@laptop.org> > > > Cc: Grant Likely <grant.likely@secretlab.ca> > > > --- > > > .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 40 ++++++++ > > > drivers/mmc/host/sdhci-esdhc-imx.c | 102 +++++++++++++++++++- > > > 2 files changed, 137 insertions(+), 5 deletions(-) > > > create mode 100644 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > > > > > diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > > new file mode 100644 > > > index 0000000..351d239 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt > > > @@ -0,0 +1,40 @@ > > > +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX > > > + > > > +The Enhanced Secure Digital Host Controller on Freescale i.MX family > > > +provides an interface for MMC, SD, and SDIO types of memory cards. > > > + > > > +Required properties: > > > +- compatible : Should be "fsl,<chip>-esdhc" > > > +- reg : Should contain eSDHC registers location and length > > > +- interrupts : Should contain eSDHC interrupt > > > +- cd-type : String, card detection (CD) method. Supported values are: > > > + "none" : No CD > > > + "controller" : Uses eSDHC controller internal CD signal > > > + "gpio" : Uses GPIO pin for CD > > > + "permanent" : No CD because card is permanently wired to host > > > +- wp-type : String, write protection (WP) method. Supported values are: > > > + "none" : No WP > > > + "controller" : Uses eSDHC controller internal WP signal > > > + "gpio" : Uses GPIO pin for WP > > > +- gpios : Should specify GPIOs in this order: CD GPIO, WP GPIO, if > > > + properties cd-type and wp-type are "gpio". > > > > Again, be explicit in your gpios property names. Create a different > > property for each gpio: cd-gpios and wp-gpios. > > > > As for wp-type and cd-type, I think you can drop them. Default to > > internal controller CD and WP pins. Use gpio if cd-gpios or wp-gpios > > is present, and define specific properties for the no-wp, no-cd and > > fixed-card cases. (can you tell that I'm not a fan of the "*-type" > > binding for this driver?) :-) > > > I would let default be no CD/WP, and define properties for > controller internal CD/WP and wired case, if you do not see a > problem with it. Okay. g. -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt new file mode 100644 index 0000000..351d239 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -0,0 +1,40 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX + +The Enhanced Secure Digital Host Controller on Freescale i.MX family +provides an interface for MMC, SD, and SDIO types of memory cards. + +Required properties: +- compatible : Should be "fsl,<chip>-esdhc" +- reg : Should contain eSDHC registers location and length +- interrupts : Should contain eSDHC interrupt +- cd-type : String, card detection (CD) method. Supported values are: + "none" : No CD + "controller" : Uses eSDHC controller internal CD signal + "gpio" : Uses GPIO pin for CD + "permanent" : No CD because card is permanently wired to host +- wp-type : String, write protection (WP) method. Supported values are: + "none" : No WP + "controller" : Uses eSDHC controller internal WP signal + "gpio" : Uses GPIO pin for WP +- gpios : Should specify GPIOs in this order: CD GPIO, WP GPIO, if + properties cd-type and wp-type are "gpio". + +Examples: + +esdhc@70004000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70004000 0x4000>; + interrupts = <1>; + fsl,cd-type = "controller"; + fsl,wp-type = "controller"; +}; + +esdhc@70008000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70008000 0x4000>; + interrupts = <2>; + fsl,cd-type = "gpio"; + fsl,wp-type = "gpio"; + cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ +}; diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index 1edda29..593d6b9 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -20,6 +20,9 @@ #include <linux/mmc/host.h> #include <linux/mmc/mmc.h> #include <linux/mmc/sdio.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> #include <mach/esdhc.h> #include "sdhci-pltfm.h" #include "sdhci-esdhc.h" @@ -72,6 +75,14 @@ static struct platform_device_id imx_esdhc_devtype[] = { } }; +static const struct of_device_id imx_esdhc_dt_ids[] = { + { .compatible = "fsl,imx25-esdhc", .data = &imx_esdhc_devtype[IMX25_ESDHC], }, + { .compatible = "fsl,imx35-esdhc", .data = &imx_esdhc_devtype[IMX35_ESDHC], }, + { .compatible = "fsl,imx51-esdhc", .data = &imx_esdhc_devtype[IMX51_ESDHC], }, + { .compatible = "fsl,imx53-esdhc", .data = &imx_esdhc_devtype[IMX53_ESDHC], }, + { /* sentinel */ } +}; + static inline int is_imx25_esdhc(struct pltfm_imx_data *data) { return data->devtype == IMX25_ESDHC; @@ -305,24 +316,96 @@ static irqreturn_t cd_irq(int irq, void *data) return IRQ_HANDLED; }; +#ifdef CONFIG_OF +static const char *cd_types[] = { + [ESDHC_CD_NONE] = "none", + [ESDHC_CD_CONTROLLER] = "controller", + [ESDHC_CD_GPIO] = "gpio", + [ESDHC_CD_PERMANENT] = "permanent", +}; + +static const char *wp_types[] = { + [ESDHC_WP_NONE] = "none", + [ESDHC_WP_CONTROLLER] = "controller", + [ESDHC_WP_GPIO] = "gpio", +}; + +static int __devinit sdhci_esdhc_imx_probe_dt(struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(imx_esdhc_dt_ids, &pdev->dev); + struct device_node *np = pdev->dev.of_node; + struct esdhc_platform_data *boarddata; + int err, i; + const char *cd, *wp; + + if (!np) + return -ENODEV; + + boarddata = kzalloc(sizeof(*boarddata), GFP_KERNEL); + if (!boarddata) + return -ENOMEM; + pdev->dev.platform_data = boarddata; + + err = of_property_read_string(np, "fsl,cd-type", &cd); + if (err) + return err; + for (i = 0; i < ARRAY_SIZE(cd_types); i++) + if (!strcasecmp(cd, cd_types[i])) { + boarddata->cd_type = i; + break; + } + + err = of_property_read_string(np, "fsl,wp-type", &wp); + if (err) + return err; + for (i = 0; i < ARRAY_SIZE(wp_types); i++) + if (!strcasecmp(wp, wp_types[i])) { + boarddata->wp_type = i; + break; + } + + boarddata->cd_gpio = of_get_gpio(np, 0); + boarddata->wp_gpio = of_get_gpio(np, 1); + + pdev->id_entry = of_id->data; + + return 0; +} +#else +static inline int sdhci_esdhc_imx_probe_dt(struct platform_device *pdev) +{ + return 0; +} +#endif + static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) { + struct device_node *np = pdev->dev.of_node; struct sdhci_pltfm_host *pltfm_host; struct sdhci_host *host; - struct esdhc_platform_data *boarddata; + struct esdhc_platform_data *boarddata = NULL; struct clk *clk; int err; struct pltfm_imx_data *imx_data; + err = sdhci_esdhc_imx_probe_dt(pdev); + if (err) + return err; + host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata); - if (IS_ERR(host)) - return PTR_ERR(host); + if (IS_ERR(host)) { + err = PTR_ERR(host); + goto err_sdhci_pltfm; + } pltfm_host = sdhci_priv(host); imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL); - if (!imx_data) - return -ENOMEM; + if (!imx_data) { + err = -ENOMEM; + goto err_imx_data; + } imx_data->devtype = pdev->id_entry->driver_data; pltfm_host->priv = imx_data; @@ -416,12 +499,17 @@ no_board_data: clk_put(pltfm_host->clk); err_clk_get: kfree(imx_data); +err_imx_data: sdhci_pltfm_free(pdev); +err_sdhci_pltfm: + if (np) + kfree(boarddata); return err; } static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) { + struct device_node *np = pdev->dev.of_node; struct sdhci_host *host = platform_get_drvdata(pdev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct esdhc_platform_data *boarddata = host->mmc->parent->platform_data; @@ -444,6 +532,9 @@ static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) sdhci_pltfm_free(pdev); + if (np) + kfree(boarddata); + return 0; } @@ -451,6 +542,7 @@ static struct platform_driver sdhci_esdhc_imx_driver = { .driver = { .name = "sdhci-esdhc-imx", .owner = THIS_MODULE, + .of_match_table = imx_esdhc_dt_ids, }, .id_table = imx_esdhc_devtype, .probe = sdhci_esdhc_imx_probe,
The patch adds device tree probe support for sdhci-esdhc-imx driver. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Wolfram Sang <w.sang@pengutronix.de> Cc: Chris Ball <cjb@laptop.org> Cc: Grant Likely <grant.likely@secretlab.ca> --- .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 40 ++++++++ drivers/mmc/host/sdhci-esdhc-imx.c | 102 +++++++++++++++++++- 2 files changed, 137 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt