| Message ID | 20170801045434.8733-2-vigneshr@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Aug 01, 2017 at 10:24:28AM +0530, Vignesh R wrote: > As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access > Controller programming sequence, a delay equal to couple QSPI master > clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and > writing data to the flash. Add a new compatible to handle the couple of > cycles of delay required in the indirect write sequence, since this > delay is specific to TI 66AK2G SoC. > > [1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf > > Signed-off-by: Vignesh R <vigneshr@ti.com> > --- > Documentation/devicetree/bindings/mtd/cadence-quadspi.txt | 1 + > drivers/mtd/spi-nor/cadence-quadspi.c | 13 +++++++++++++ > 2 files changed, 14 insertions(+) > > diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > index f248056da24c..fdd511a83511 100644 > --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > @@ -2,6 +2,7 @@ > > Required properties: > - compatible : Should be "cdns,qspi-nor". > + Should be "ti,k2g-qspi" for TI 66AK2G platform. > - reg : Contains two entries, each of which is a tuple consisting of a > physical address and length. The first entry is the address and > length of the controller register set. The second entry is the > diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c > index 53c7d8e0327a..94571590371d 100644 > --- a/drivers/mtd/spi-nor/cadence-quadspi.c > +++ b/drivers/mtd/spi-nor/cadence-quadspi.c > @@ -76,6 +76,7 @@ struct cqspi_st { > u32 fifo_depth; > u32 fifo_width; > u32 trigger_address; > + u32 wr_delay; > struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT]; > }; > > @@ -608,6 +609,14 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, > reinit_completion(&cqspi->transfer_complete); > writel(CQSPI_REG_INDIRECTWR_START_MASK, > reg_base + CQSPI_REG_INDIRECTWR); > + /* > + * As per 66AK2G02 TRM SPRUHY8F section 11.15.5.3 Indirect Access > + * Controller programming sequence, couple of cycles of > + * QSPI_REF_CLK delay is required for the above bit to > + * be internally synchronized by the QSPI module. Provide 5 > + * cycles of delay. > + */ > + ndelay(cqspi->wr_delay); > > while (remaining > 0) { > write_bytes = remaining > page_size ? page_size : remaining; > @@ -1213,6 +1222,9 @@ static int cqspi_probe(struct platform_device *pdev) > } > > cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk); > + if (of_device_is_compatible(dev->of_node, "ti,k2g-qspi")) > + cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC, > + cqspi->master_ref_clk_hz); Use the data pointer in the of_device_id table and put the delay value there. > > ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0, > pdev->name, cqspi); > @@ -1285,6 +1297,7 @@ static const struct dev_pm_ops cqspi__dev_pm_ops = { > > static const struct of_device_id cqspi_dt_ids[] = { > {.compatible = "cdns,qspi-nor",}, > + {.compatible = "ti,k2g-qspi",}, > { /* end of table */ } > }; > > -- > 2.13.3 >
On Tue, Aug 01, 2017 at 10:24:28AM +0530, Vignesh R wrote: > As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access > Controller programming sequence, a delay equal to couple QSPI master > clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and > writing data to the flash. Add a new compatible to handle the couple of > cycles of delay required in the indirect write sequence, since this > delay is specific to TI 66AK2G SoC. > > [1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf > > Signed-off-by: Vignesh R <vigneshr@ti.com> > --- > Documentation/devicetree/bindings/mtd/cadence-quadspi.txt | 1 + > drivers/mtd/spi-nor/cadence-quadspi.c | 13 +++++++++++++ > 2 files changed, 14 insertions(+) > > diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > index f248056da24c..fdd511a83511 100644 > --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt > @@ -2,6 +2,7 @@ > > Required properties: > - compatible : Should be "cdns,qspi-nor". > + Should be "ti,k2g-qspi" for TI 66AK2G platform. Also, this doesn't indicate that "cdns,qspi-nor" is a fallback as you have in the dts files. Reformat to 1 valid combination per line. > - reg : Contains two entries, each of which is a tuple consisting of a > physical address and length. The first entry is the address and > length of the controller register set. The second entry is the
On Thursday 10 August 2017 05:35 AM, Rob Herring wrote: > On Tue, Aug 01, 2017 at 10:24:28AM +0530, Vignesh R wrote: >> As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access >> Controller programming sequence, a delay equal to couple QSPI master >> clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and >> writing data to the flash. Add a new compatible to handle the couple of >> cycles of delay required in the indirect write sequence, since this >> delay is specific to TI 66AK2G SoC. >> >> [1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf >> [...] >> + /* >> + * As per 66AK2G02 TRM SPRUHY8F section 11.15.5.3 Indirect Access >> + * Controller programming sequence, couple of cycles of >> + * QSPI_REF_CLK delay is required for the above bit to >> + * be internally synchronized by the QSPI module. Provide 5 >> + * cycles of delay. >> + */ >> + ndelay(cqspi->wr_delay); >> >> while (remaining > 0) { >> write_bytes = remaining > page_size ? page_size : remaining; >> @@ -1213,6 +1222,9 @@ static int cqspi_probe(struct platform_device *pdev) >> } >> >> cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk); >> + if (of_device_is_compatible(dev->of_node, "ti,k2g-qspi")) >> + cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC, >> + cqspi->master_ref_clk_hz); > > Use the data pointer in the of_device_id table and put the delay value > there. > I thought about this, but for a given SoC, delay value might vary depending on what frequency QSPI master_ref_clk is set to. So hard coding will not help. How about having a flag (CQSPI_NEEDS_WR_DELAY) in data pointer and then using that to determine whether or not to calculate and set delay here? >> >> ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0, >> pdev->name, cqspi); >> @@ -1285,6 +1297,7 @@ static const struct dev_pm_ops cqspi__dev_pm_ops = { >> >> static const struct of_device_id cqspi_dt_ids[] = { >> {.compatible = "cdns,qspi-nor",}, >> + {.compatible = "ti,k2g-qspi",}, >> { /* end of table */ } >> }; >> >> -- >> 2.13.3 >>
On Thursday 10 August 2017 05:38 AM, Rob Herring wrote: > On Tue, Aug 01, 2017 at 10:24:28AM +0530, Vignesh R wrote: >> As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access >> Controller programming sequence, a delay equal to couple QSPI master >> clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and >> writing data to the flash. Add a new compatible to handle the couple of >> cycles of delay required in the indirect write sequence, since this >> delay is specific to TI 66AK2G SoC. >> >> [1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf >> >> Signed-off-by: Vignesh R <vigneshr@ti.com> >> --- >> Documentation/devicetree/bindings/mtd/cadence-quadspi.txt | 1 + >> drivers/mtd/spi-nor/cadence-quadspi.c | 13 +++++++++++++ >> 2 files changed, 14 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt >> index f248056da24c..fdd511a83511 100644 >> --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt >> +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt >> @@ -2,6 +2,7 @@ >> >> Required properties: >> - compatible : Should be "cdns,qspi-nor". >> + Should be "ti,k2g-qspi" for TI 66AK2G platform. > > Also, this doesn't indicate that "cdns,qspi-nor" is a fallback as you > have in the dts files. Reformat to 1 valid combination per line. > Agreed, will fix it in v2.
diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt index f248056da24c..fdd511a83511 100644 --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -2,6 +2,7 @@ Required properties: - compatible : Should be "cdns,qspi-nor". + Should be "ti,k2g-qspi" for TI 66AK2G platform. - reg : Contains two entries, each of which is a tuple consisting of a physical address and length. The first entry is the address and length of the controller register set. The second entry is the diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c index 53c7d8e0327a..94571590371d 100644 --- a/drivers/mtd/spi-nor/cadence-quadspi.c +++ b/drivers/mtd/spi-nor/cadence-quadspi.c @@ -76,6 +76,7 @@ struct cqspi_st { u32 fifo_depth; u32 fifo_width; u32 trigger_address; + u32 wr_delay; struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT]; }; @@ -608,6 +609,14 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, reinit_completion(&cqspi->transfer_complete); writel(CQSPI_REG_INDIRECTWR_START_MASK, reg_base + CQSPI_REG_INDIRECTWR); + /* + * As per 66AK2G02 TRM SPRUHY8F section 11.15.5.3 Indirect Access + * Controller programming sequence, couple of cycles of + * QSPI_REF_CLK delay is required for the above bit to + * be internally synchronized by the QSPI module. Provide 5 + * cycles of delay. + */ + ndelay(cqspi->wr_delay); while (remaining > 0) { write_bytes = remaining > page_size ? page_size : remaining; @@ -1213,6 +1222,9 @@ static int cqspi_probe(struct platform_device *pdev) } cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk); + if (of_device_is_compatible(dev->of_node, "ti,k2g-qspi")) + cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC, + cqspi->master_ref_clk_hz); ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0, pdev->name, cqspi); @@ -1285,6 +1297,7 @@ static const struct dev_pm_ops cqspi__dev_pm_ops = { static const struct of_device_id cqspi_dt_ids[] = { {.compatible = "cdns,qspi-nor",}, + {.compatible = "ti,k2g-qspi",}, { /* end of table */ } };
As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access Controller programming sequence, a delay equal to couple QSPI master clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and writing data to the flash. Add a new compatible to handle the couple of cycles of delay required in the indirect write sequence, since this delay is specific to TI 66AK2G SoC. [1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf Signed-off-by: Vignesh R <vigneshr@ti.com> --- Documentation/devicetree/bindings/mtd/cadence-quadspi.txt | 1 + drivers/mtd/spi-nor/cadence-quadspi.c | 13 +++++++++++++ 2 files changed, 14 insertions(+)