@@ -96,3 +96,12 @@
status = "okay";
};
};
+
+&pcie1_rc {
+ status = "okay";
+ gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie1_ep {
+ gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+};
@@ -88,7 +88,12 @@
load-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
};
-&pcie1 {
+&pcie1_rc {
+ status = "okay";
+ gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie1_ep {
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
};
@@ -570,7 +570,12 @@
};
};
-&pcie1 {
+&pcie1_rc {
+ status = "ok";
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+};
+
+&pcie1_ep {
gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
};
@@ -720,3 +720,7 @@
status = "okay";
};
};
+
+&pcie1_rc {
+ status = "okay";
+};
@@ -196,6 +196,7 @@
scm_conf1: scm_conf@1c04 {
compatible = "syscon";
reg = <0x1c04 0x0020>;
+ #syscon-cells = <2>;
};
scm_conf_pcie: scm_conf@1c24 {
@@ -287,7 +288,11 @@
#address-cells = <1>;
ranges = <0x51000000 0x51000000 0x3000
0x0 0x20000000 0x10000000>;
- pcie1: pcie@51000000 {
+ /**
+ * To enable PCI endpoint mode, disable the pcie1_rc
+ * node and enable pcie1_ep mode.
+ */
+ pcie1_rc: pcie@51000000 {
compatible = "ti,dra7-pcie";
reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>;
reg-names = "rc_dbics", "ti_conf", "config";
@@ -309,12 +314,28 @@
<0 0 0 2 &pcie1_intc 2>,
<0 0 0 3 &pcie1_intc 3>,
<0 0 0 4 &pcie1_intc 4>;
+ status = "disabled";
pcie1_intc: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
};
};
+
+ pcie1_ep: pcie_ep@51000000 {
+ compatible = "ti,dra7-pcie-ep";
+ reg = <0x51000000 0x28>, <0x51002000 0x14c>, <0x51001000 0x28>, <0x1000 0x10000000>;
+ reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
+ interrupts = <0 232 0x4>;
+ num-lanes = <1>;
+ num-ib-windows = <4>;
+ num-ob-windows = <16>;
+ ti,hwmods = "pcie1";
+ phys = <&pcie1_phy>;
+ phy-names = "pcie-phy0";
+ ti,syscon-unaligned-access = <&scm_conf1 0x14 2>;
+ status = "disabled";
+ };
};
axi@1 {
@@ -564,3 +564,7 @@
status = "okay";
};
};
+
+&pcie1_rc {
+ status = "okay";
+};
Add pcie1 dt node in order for the controller to operate in endpoint mode. However since none of the dra7 based boards have slots configured to operate in endpoint mode, keep EP mode disabled. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- arch/arm/boot/dts/am571x-idk.dts | 9 +++++++++ arch/arm/boot/dts/am572x-idk.dts | 7 ++++++- arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 7 ++++++- arch/arm/boot/dts/dra7-evm.dts | 4 ++++ arch/arm/boot/dts/dra7.dtsi | 23 ++++++++++++++++++++++- arch/arm/boot/dts/dra72-evm-common.dtsi | 4 ++++ 6 files changed, 51 insertions(+), 3 deletions(-)