@@ -238,5 +238,6 @@ source "drivers/firmware/google/Kconfig"
source "drivers/firmware/efi/Kconfig"
source "drivers/firmware/meson/Kconfig"
source "drivers/firmware/tegra/Kconfig"
+source "drivers/firmware/xilinx/Kconfig"
endmenu
@@ -29,3 +29,4 @@ obj-$(CONFIG_GOOGLE_FIRMWARE) += google/
obj-$(CONFIG_EFI) += efi/
obj-$(CONFIG_UEFI_CPER) += efi/
obj-y += tegra/
+obj-y += xilinx/
new file mode 100644
@@ -0,0 +1,6 @@
+#
+# Xilinx ZYNQ MPSoC configuration
+#
+menuconfig SOC_XILINX_ZYNQMP
+ bool "Xilinx Zynq MPSoC Firmware driver support"
+ depends on ARCH_ZYNQMP
new file mode 100644
@@ -0,0 +1 @@
+obj-$(CONFIG_SOC_XILINX_ZYNQMP) += zynqmp/firmware.o
new file mode 100644
@@ -0,0 +1,382 @@
+/*
+ * Xilinx Zynq MPSoC Firware layer
+ *
+ * Copyright (C) 2014-2017 Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Davorin Mista <davorin.mista@aggios.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/compiler.h>
+#include <linux/arm-smccc.h>
+#include <linux/of.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/uaccess.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+
+#include <linux/firmware/xilinx/zynqmp/firmware.h>
+
+/**
+ * zynqmp_pm_ret_code - Convert PMU-FW error codes to Linux error codes
+ * @ret_status: PMUFW return code
+ *
+ * Return: corresponding Linux error code
+ */
+static int zynqmp_pm_ret_code(u32 ret_status)
+{
+ switch (ret_status) {
+ case XST_PM_SUCCESS:
+ case XST_PM_DOUBLE_REQ:
+ return 0;
+ case XST_PM_NO_ACCESS:
+ return -EACCES;
+ case XST_PM_ABORT_SUSPEND:
+ return -ECANCELED;
+ case XST_PM_INTERNAL:
+ case XST_PM_CONFLICT:
+ case XST_PM_INVALID_NODE:
+ default:
+ return -EINVAL;
+ }
+}
+
+static noinline int do_fw_call_fail(u64 arg0, u64 arg1, u64 arg2,
+ u32 *ret_payload)
+{
+ return -ENODEV;
+}
+
+/*
+ * PM function call wrapper
+ * Invoke do_fw_call_smc or do_fw_call_hvc, depending on the configuration
+ */
+static int (*do_fw_call)(u64, u64, u64, u32 *ret_payload) = do_fw_call_fail;
+
+/**
+ * do_fw_call_smc - Call system-level power management layer (SMC)
+ * @arg0: Argument 0 to SMC call
+ * @arg1: Argument 1 to SMC call
+ * @arg2: Argument 2 to SMC call
+ * @ret_payload: Returned value array
+ *
+ * Return: Returns status, either success or error+reason
+ *
+ * Invoke power management function via SMC call (no hypervisor present)
+ */
+static noinline int do_fw_call_smc(u64 arg0, u64 arg1, u64 arg2,
+ u32 *ret_payload)
+{
+ struct arm_smccc_res res;
+
+ arm_smccc_smc(arg0, arg1, arg2, 0, 0, 0, 0, 0, &res);
+
+ if (ret_payload) {
+ ret_payload[0] = (u32)res.a0;
+ ret_payload[1] = (u32)(res.a0 >> 32);
+ ret_payload[2] = (u32)res.a1;
+ ret_payload[3] = (u32)(res.a1 >> 32);
+ ret_payload[4] = (u32)res.a2;
+ }
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)res.a0);
+}
+
+/**
+ * do_fw_call_hvc - Call system-level power management layer (HVC)
+ * @arg0: Argument 0 to HVC call
+ * @arg1: Argument 1 to HVC call
+ * @arg2: Argument 2 to HVC call
+ * @ret_payload: Returned value array
+ *
+ * Return: Returns status, either success or error+reason
+ *
+ * Invoke power management function via HVC
+ * HVC-based for communication through hypervisor
+ * (no direct communication with ATF)
+ */
+static noinline int do_fw_call_hvc(u64 arg0, u64 arg1, u64 arg2,
+ u32 *ret_payload)
+{
+ struct arm_smccc_res res;
+
+ arm_smccc_hvc(arg0, arg1, arg2, 0, 0, 0, 0, 0, &res);
+
+ if (ret_payload) {
+ ret_payload[0] = (u32)res.a0;
+ ret_payload[1] = (u32)(res.a0 >> 32);
+ ret_payload[2] = (u32)res.a1;
+ ret_payload[3] = (u32)(res.a1 >> 32);
+ ret_payload[4] = (u32)res.a2;
+ }
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)res.a0);
+}
+
+/**
+ * invoke_pm_fn - Invoke the system-level power management layer caller
+ * function depending on the configuration
+ * @pm_api_id: Requested PM-API call
+ * @arg0: Argument 0 to requested PM-API call
+ * @arg1: Argument 1 to requested PM-API call
+ * @arg2: Argument 2 to requested PM-API call
+ * @arg3: Argument 3 to requested PM-API call
+ * @ret_payload: Returned value array
+ *
+ * Return: Returns status, either success or error+reason
+ *
+ * Invoke power management function for SMC or HVC call, depending on
+ * configuration
+ * Following SMC Calling Convention (SMCCC) for SMC64:
+ * Pm Function Identifier,
+ * PM_SIP_SVC + PM_API_ID =
+ * ((SMC_TYPE_FAST << FUNCID_TYPE_SHIFT)
+ * ((SMC_64) << FUNCID_CC_SHIFT)
+ * ((SIP_START) << FUNCID_OEN_SHIFT)
+ * ((PM_API_ID) & FUNCID_NUM_MASK))
+ *
+ * PM_SIP_SVC - Registered ZynqMP SIP Service Call
+ * PM_API_ID - Power Management API ID
+ */
+static int invoke_pm_fn(u32 pm_api_id, u32 arg0, u32 arg1, u32 arg2, u32 arg3,
+ u32 *ret_payload)
+{
+ /*
+ * Added SIP service call Function Identifier
+ * Make sure to stay in x0 register
+ */
+ u64 smc_arg[4];
+
+ smc_arg[0] = PM_SIP_SVC | pm_api_id;
+ smc_arg[1] = ((u64)arg1 << 32) | arg0;
+ smc_arg[2] = ((u64)arg3 << 32) | arg2;
+
+ return do_fw_call(smc_arg[0], smc_arg[1], smc_arg[2], ret_payload);
+}
+
+/**
+ * zynqmp_pm_get_chipid - Get silicon ID registers
+ * @idcode: IDCODE register
+ * @version: version register
+ *
+ * Return: Returns the status of the operation and the idcode and version
+ * registers in @idcode and @version.
+ */
+int zynqmp_pm_get_chipid(u32 *idcode, u32 *version)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ if (!idcode || !version)
+ return -EINVAL;
+
+ invoke_pm_fn(GET_CHIPID, 0, 0, 0, 0, ret_payload);
+ *idcode = ret_payload[1];
+ *version = ret_payload[2];
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)ret_payload[0]);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_get_chipid);
+
+/**
+ * get_set_conduit_method - Choose SMC or HVC based communication
+ * @np: Pointer to the device_node structure
+ *
+ * Use SMC or HVC-based functions to communicate with EL2/EL3
+ */
+static void get_set_conduit_method(struct device_node *np)
+{
+ const char *method;
+ struct device *dev;
+
+ dev = container_of(&np, struct device, of_node);
+
+ if (of_property_read_string(np, "method", &method)) {
+ dev_warn(dev, "%s Missing \"method\" property - defaulting to smc\n",
+ __func__);
+ do_fw_call = do_fw_call_smc;
+ return;
+ }
+
+ if (!strcmp("hvc", method)) {
+ do_fw_call = do_fw_call_hvc;
+
+ } else if (!strcmp("smc", method)) {
+ do_fw_call = do_fw_call_smc;
+ } else {
+ dev_warn(dev, "%s Invalid \"method\" property: %s - defaulting to smc\n",
+ __func__, method);
+ do_fw_call = do_fw_call_smc;
+ }
+}
+
+/**
+ * zynqmp_pm_reset_assert - Request setting of reset (1 - assert, 0 - release)
+ * @reset: Reset to be configured
+ * @assert_flag: Flag stating should reset be asserted (1) or
+ * released (0)
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag)
+{
+ return invoke_pm_fn(RESET_ASSERT, reset, assert_flag, 0, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_reset_assert);
+
+/**
+ * zynqmp_pm_reset_get_status - Get status of the reset
+ * @reset: Reset whose status should be returned
+ * @status: Returned status
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, u32 *status)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ if (!status)
+ return zynqmp_pm_ret_code(XST_PM_CONFLICT);
+
+ invoke_pm_fn(RESET_GET_STATUS, reset, 0, 0, 0, ret_payload);
+ *status = ret_payload[1];
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)ret_payload[0]);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_reset_get_status);
+
+/**
+ * zynqmp_pm_mmio_write - Perform write to protected mmio
+ * @address: Address to write to
+ * @mask: Mask to apply
+ * @value: Value to write
+ *
+ * This function provides access to PM-related control registers
+ * that may not be directly accessible by a particular PU.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_mmio_write(const u32 address,
+ const u32 mask,
+ const u32 value)
+{
+ return invoke_pm_fn(MMIO_WRITE, address, mask, value, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_mmio_write);
+
+/**
+ * zynqmp_pm_mmio_read - Read value from protected mmio
+ * @address: Address to write to
+ * @value: Value to read
+ *
+ * This function provides access to PM-related control registers
+ * that may not be directly accessible by a particular PU.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_mmio_read(const u32 address, u32 *value)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ if (!value)
+ return -EINVAL;
+
+ invoke_pm_fn(MMIO_READ, address, 0, 0, 0, ret_payload);
+ *value = ret_payload[1];
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)ret_payload[0]);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_mmio_read);
+
+/**
+ * zynqmp_pm_fpga_load - Perform the fpga load
+ * @address: Address to write to
+ * @size: pl bitstream size
+ * @flags:
+ * BIT(0) - Bit-stream type.
+ * 0 - Full Bit-stream.
+ * 1 - Partial Bit-stream.
+ * BIT(1) - Authentication.
+ * 1 - Enable.
+ * 0 - Disable.
+ * BIT(2) - Encryption.
+ * 1 - Enable.
+ * 0 - Disable.
+ * NOTE -
+ * The current implementation supports only Full Bit-stream.
+ *
+ * This function provides access to xilfpga library to transfer
+ * the required bitstream into PL.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_fpga_load(const u64 address, const u32 size, const u32 flags)
+{
+ return invoke_pm_fn(FPGA_LOAD, (u32)address,
+ ((u32)(address >> 32)), size, flags, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_load);
+
+/**
+ * zynqmp_pm_fpga_get_status - Read value from PCAP status register
+ * @value: Value to read
+ *
+ *This function provides access to the xilfpga library to get
+ *the PCAP status
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_fpga_get_status(u32 *value)
+{
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ if (!value)
+ return -EINVAL;
+
+ invoke_pm_fn(FPGA_GET_STATUS, 0, 0, 0, 0, ret_payload);
+ *value = ret_payload[1];
+
+ return zynqmp_pm_ret_code((enum pm_ret_status)ret_payload[0]);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_fpga_get_status);
+
+static int __init zynqmp_plat_init(void)
+{
+ struct device_node *np;
+ int ret = 0;
+
+ np = of_find_compatible_node(NULL, NULL, "xlnx,zynqmp");
+ if (!np)
+ return 0;
+ of_node_put(np);
+
+ /* We're running on a ZynqMP machine, the PM node is mandatory. */
+ np = of_find_compatible_node(NULL, NULL, "xlnx,zynqmp-pm");
+ if (!np)
+ panic("%s: pm node not found\n", __func__);
+
+ get_set_conduit_method(np);
+
+ pr_info("%s ZynqMP firmware interface up\n", __func__);
+
+ of_node_put(np);
+ return ret;
+}
+
+early_initcall(zynqmp_plat_init);
new file mode 100644
@@ -0,0 +1,232 @@
+/*
+ * Xilinx Zynq MPSoC Firmware layer
+ *
+ * Copyright (C) 2014-2017 Xilinx
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Davorin Mista <davorin.mista@aggios.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __SOC_ZYNQMP_FIRMWARE_H__
+#define __SOC_ZYNQMP_FIRMWARE_H__
+
+/* SMC SIP service Call Function Identifier Prefix */
+#define PM_SIP_SVC 0xC2000000
+#define GET_CALLBACK_DATA 0xa01
+#define SET_SUSPEND_MODE 0xa02
+
+/* Number of 32bits values in payload */
+#define PAYLOAD_ARG_CNT 5U
+
+/* Number of arguments for a callback */
+#define CB_ARG_CNT 4
+
+/* Payload size (consists of callback API ID + arguments) */
+#define CB_PAYLOAD_SIZE (CB_ARG_CNT + 1)
+
+/* Global general storage register base address */
+#define GGS_BASEADDR (0xFFD80030U)
+#define GSS_NUM_REGS (4)
+
+/* Persistent global general storage register base address */
+#define PGGS_BASEADDR (0xFFD80050U)
+#define PGSS_NUM_REGS (4)
+
+enum pm_api_id {
+ /* Miscellaneous API functions: */
+ GET_API_VERSION = 1,
+ SET_CONFIGURATION,
+ GET_NODE_STATUS,
+ GET_OPERATING_CHARACTERISTIC,
+ REGISTER_NOTIFIER,
+ /* API for suspending of PUs: */
+ REQUEST_SUSPEND,
+ SELF_SUSPEND,
+ FORCE_POWERDOWN,
+ ABORT_SUSPEND,
+ REQUEST_WAKEUP,
+ SET_WAKEUP_SOURCE,
+ SYSTEM_SHUTDOWN,
+ /* API for managing PM slaves: */
+ REQUEST_NODE,
+ RELEASE_NODE,
+ SET_REQUIREMENT,
+ SET_MAX_LATENCY,
+ /* Direct control API functions: */
+ RESET_ASSERT,
+ RESET_GET_STATUS,
+ MMIO_WRITE,
+ MMIO_READ,
+ PM_INIT_FINALIZE,
+ FPGA_LOAD,
+ FPGA_GET_STATUS,
+ GET_CHIPID,
+};
+
+/* PMU-FW return status codes */
+enum pm_ret_status {
+ XST_PM_SUCCESS = 0,
+ XST_PM_INTERNAL = 2000,
+ XST_PM_CONFLICT,
+ XST_PM_NO_ACCESS,
+ XST_PM_INVALID_NODE,
+ XST_PM_DOUBLE_REQ,
+ XST_PM_ABORT_SUSPEND,
+};
+
+enum zynqmp_pm_reset_action {
+ PM_RESET_ACTION_RELEASE,
+ PM_RESET_ACTION_ASSERT,
+ PM_RESET_ACTION_PULSE,
+};
+
+enum zynqmp_pm_reset {
+ ZYNQMP_PM_RESET_START = 999,
+ ZYNQMP_PM_RESET_PCIE_CFG,
+ ZYNQMP_PM_RESET_PCIE_BRIDGE,
+ ZYNQMP_PM_RESET_PCIE_CTRL,
+ ZYNQMP_PM_RESET_DP,
+ ZYNQMP_PM_RESET_SWDT_CRF,
+ ZYNQMP_PM_RESET_AFI_FM5,
+ ZYNQMP_PM_RESET_AFI_FM4,
+ ZYNQMP_PM_RESET_AFI_FM3,
+ ZYNQMP_PM_RESET_AFI_FM2,
+ ZYNQMP_PM_RESET_AFI_FM1,
+ ZYNQMP_PM_RESET_AFI_FM0,
+ ZYNQMP_PM_RESET_GDMA,
+ ZYNQMP_PM_RESET_GPU_PP1,
+ ZYNQMP_PM_RESET_GPU_PP0,
+ ZYNQMP_PM_RESET_GPU,
+ ZYNQMP_PM_RESET_GT,
+ ZYNQMP_PM_RESET_SATA,
+ ZYNQMP_PM_RESET_ACPU3_PWRON,
+ ZYNQMP_PM_RESET_ACPU2_PWRON,
+ ZYNQMP_PM_RESET_ACPU1_PWRON,
+ ZYNQMP_PM_RESET_ACPU0_PWRON,
+ ZYNQMP_PM_RESET_APU_L2,
+ ZYNQMP_PM_RESET_ACPU3,
+ ZYNQMP_PM_RESET_ACPU2,
+ ZYNQMP_PM_RESET_ACPU1,
+ ZYNQMP_PM_RESET_ACPU0,
+ ZYNQMP_PM_RESET_DDR,
+ ZYNQMP_PM_RESET_APM_FPD,
+ ZYNQMP_PM_RESET_SOFT,
+ ZYNQMP_PM_RESET_GEM0,
+ ZYNQMP_PM_RESET_GEM1,
+ ZYNQMP_PM_RESET_GEM2,
+ ZYNQMP_PM_RESET_GEM3,
+ ZYNQMP_PM_RESET_QSPI,
+ ZYNQMP_PM_RESET_UART0,
+ ZYNQMP_PM_RESET_UART1,
+ ZYNQMP_PM_RESET_SPI0,
+ ZYNQMP_PM_RESET_SPI1,
+ ZYNQMP_PM_RESET_SDIO0,
+ ZYNQMP_PM_RESET_SDIO1,
+ ZYNQMP_PM_RESET_CAN0,
+ ZYNQMP_PM_RESET_CAN1,
+ ZYNQMP_PM_RESET_I2C0,
+ ZYNQMP_PM_RESET_I2C1,
+ ZYNQMP_PM_RESET_TTC0,
+ ZYNQMP_PM_RESET_TTC1,
+ ZYNQMP_PM_RESET_TTC2,
+ ZYNQMP_PM_RESET_TTC3,
+ ZYNQMP_PM_RESET_SWDT_CRL,
+ ZYNQMP_PM_RESET_NAND,
+ ZYNQMP_PM_RESET_ADMA,
+ ZYNQMP_PM_RESET_GPIO,
+ ZYNQMP_PM_RESET_IOU_CC,
+ ZYNQMP_PM_RESET_TIMESTAMP,
+ ZYNQMP_PM_RESET_RPU_R50,
+ ZYNQMP_PM_RESET_RPU_R51,
+ ZYNQMP_PM_RESET_RPU_AMBA,
+ ZYNQMP_PM_RESET_OCM,
+ ZYNQMP_PM_RESET_RPU_PGE,
+ ZYNQMP_PM_RESET_USB0_CORERESET,
+ ZYNQMP_PM_RESET_USB1_CORERESET,
+ ZYNQMP_PM_RESET_USB0_HIBERRESET,
+ ZYNQMP_PM_RESET_USB1_HIBERRESET,
+ ZYNQMP_PM_RESET_USB0_APB,
+ ZYNQMP_PM_RESET_USB1_APB,
+ ZYNQMP_PM_RESET_IPI,
+ ZYNQMP_PM_RESET_APM_LPD,
+ ZYNQMP_PM_RESET_RTC,
+ ZYNQMP_PM_RESET_SYSMON,
+ ZYNQMP_PM_RESET_AFI_FM6,
+ ZYNQMP_PM_RESET_LPD_SWDT,
+ ZYNQMP_PM_RESET_FPD,
+ ZYNQMP_PM_RESET_RPU_DBG1,
+ ZYNQMP_PM_RESET_RPU_DBG0,
+ ZYNQMP_PM_RESET_DBG_LPD,
+ ZYNQMP_PM_RESET_DBG_FPD,
+ ZYNQMP_PM_RESET_APLL,
+ ZYNQMP_PM_RESET_DPLL,
+ ZYNQMP_PM_RESET_VPLL,
+ ZYNQMP_PM_RESET_IOPLL,
+ ZYNQMP_PM_RESET_RPLL,
+ ZYNQMP_PM_RESET_GPO3_PL_0,
+ ZYNQMP_PM_RESET_GPO3_PL_1,
+ ZYNQMP_PM_RESET_GPO3_PL_2,
+ ZYNQMP_PM_RESET_GPO3_PL_3,
+ ZYNQMP_PM_RESET_GPO3_PL_4,
+ ZYNQMP_PM_RESET_GPO3_PL_5,
+ ZYNQMP_PM_RESET_GPO3_PL_6,
+ ZYNQMP_PM_RESET_GPO3_PL_7,
+ ZYNQMP_PM_RESET_GPO3_PL_8,
+ ZYNQMP_PM_RESET_GPO3_PL_9,
+ ZYNQMP_PM_RESET_GPO3_PL_10,
+ ZYNQMP_PM_RESET_GPO3_PL_11,
+ ZYNQMP_PM_RESET_GPO3_PL_12,
+ ZYNQMP_PM_RESET_GPO3_PL_13,
+ ZYNQMP_PM_RESET_GPO3_PL_14,
+ ZYNQMP_PM_RESET_GPO3_PL_15,
+ ZYNQMP_PM_RESET_GPO3_PL_16,
+ ZYNQMP_PM_RESET_GPO3_PL_17,
+ ZYNQMP_PM_RESET_GPO3_PL_18,
+ ZYNQMP_PM_RESET_GPO3_PL_19,
+ ZYNQMP_PM_RESET_GPO3_PL_20,
+ ZYNQMP_PM_RESET_GPO3_PL_21,
+ ZYNQMP_PM_RESET_GPO3_PL_22,
+ ZYNQMP_PM_RESET_GPO3_PL_23,
+ ZYNQMP_PM_RESET_GPO3_PL_24,
+ ZYNQMP_PM_RESET_GPO3_PL_25,
+ ZYNQMP_PM_RESET_GPO3_PL_26,
+ ZYNQMP_PM_RESET_GPO3_PL_27,
+ ZYNQMP_PM_RESET_GPO3_PL_28,
+ ZYNQMP_PM_RESET_GPO3_PL_29,
+ ZYNQMP_PM_RESET_GPO3_PL_30,
+ ZYNQMP_PM_RESET_GPO3_PL_31,
+ ZYNQMP_PM_RESET_RPU_LS,
+ ZYNQMP_PM_RESET_PS_ONLY,
+ ZYNQMP_PM_RESET_PL,
+ ZYNQMP_PM_RESET_END
+};
+
+/* Miscellaneous API functions */
+int zynqmp_pm_get_chipid(u32 *idcode, u32 *version);
+
+/* Direct-Control API functions */
+int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
+ const enum zynqmp_pm_reset_action assert_flag);
+int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
+ u32 *status);
+int zynqmp_pm_mmio_write(const u32 address,
+ const u32 mask,
+ const u32 value);
+int zynqmp_pm_mmio_read(const u32 address, u32 *value);
+int zynqmp_pm_fpga_load(const u64 address, const u32 size, const u32 flags);
+int zynqmp_pm_fpga_get_status(u32 *value);
+
+#endif /* __SOC_ZYNQMP_FIRMWARE_H__ */
This patch is adding communication layer with firmware. The most of request are coming thought ATF to PMUFW (platform management unit). Signed-off-by: Michal Simek <michal.simek@xilinx.com> --- Changes in v2: - Make zynqmp_pm_ret_code, invoke_pm_fn static Reported by Arnd - Remove pm_api_version function - no need for interface - Move driver to drivers/firmware/ Reported by Arnd and Rob drivers/firmware/Kconfig | 1 + drivers/firmware/Makefile | 1 + drivers/firmware/xilinx/Kconfig | 6 + drivers/firmware/xilinx/Makefile | 1 + drivers/firmware/xilinx/zynqmp/firmware.c | 382 ++++++++++++++++++++++++ include/linux/firmware/xilinx/zynqmp/firmware.h | 232 ++++++++++++++ 6 files changed, 623 insertions(+) create mode 100644 drivers/firmware/xilinx/Kconfig create mode 100644 drivers/firmware/xilinx/Makefile create mode 100644 drivers/firmware/xilinx/zynqmp/firmware.c create mode 100644 include/linux/firmware/xilinx/zynqmp/firmware.h