| Message ID | 1502968858-28090-4-git-send-email-varada@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
Varada, On 08/17/2017 02:20 PM, Varadarajan Narayanan wrote: > Add support for the IPQ8074 PCIe controller. IPQ8074 supports > Gen 1/2, one lane, two PCIe root complex with support for MSI and > legacy interrupts, and it conforms to PCI Express Base 2.1 > specification. > > The core init is the similar to the existing SoC, however the > clocks and reset lines differ. > > Signed-off-by: smuthayy <smuthayy@codeaurora.org> > Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org> > --- > drivers/pci/dwc/pcie-qcom.c | 208 ++++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 208 insertions(+) This patch will need re-basing too. With both comments below addressed: Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com> > > diff --git a/drivers/pci/dwc/pcie-qcom.c b/drivers/pci/dwc/pcie-qcom.c > index c4cd039..1cb03dd 100644 > --- a/drivers/pci/dwc/pcie-qcom.c > +++ b/drivers/pci/dwc/pcie-qcom.c > @@ -37,6 +37,20 @@ > #include "pcie-designware.h" > > #define PCIE20_PARF_SYS_CTRL 0x00 > +#define MST_WAKEUP_EN BIT(13) > +#define SLV_WAKEUP_EN BIT(12) > +#define MSTR_ACLK_CGC_DIS BIT(10) > +#define SLV_ACLK_CGC_DIS BIT(9) > +#define CORE_CLK_CGC_DIS BIT(6) > +#define AUX_PWR_DET BIT(4) > +#define L23_CLK_RMV_DIS BIT(2) > +#define L1_CLK_RMV_DIS BIT(1) > + > +#define PCIE20_COMMAND_STATUS 0x04 > +#define CMD_BME_VAL 0x4 > +#define PCIE20_DEVICE_CONTROL2_STATUS2 0x98 > +#define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10 > + > #define PCIE20_PARF_PHY_CTRL 0x40 > #define PCIE20_PARF_PHY_REFCLK 0x4C > #define PCIE20_PARF_DBI_BASE_ADDR 0x168 > @@ -58,9 +72,21 @@ > #define CFG_BRIDGE_SB_INIT BIT(0) > > #define PCIE20_CAP 0x70 > +#define PCIE20_CAP_LINK_CAPABILITIES (PCIE20_CAP + 0xc) > +#define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT (BIT(10) | BIT(11)) > +#define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14) > +#define PCIE_CAP_LINK1_VAL 0x2fd7f > + > +#define PCIE20_PARF_Q2A_FLUSH 0x1ac > + > +#define PCIE20_MISC_CONTROL_1_REG 0x8bc > +#define DBI_RO_WR_EN 1 > > #define PERST_DELAY_US 1000 > > +#define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358 > +#define SLV_ADDR_SPACE_SZ 0x10000000 Please use tabs instead of spaces. > + > struct qcom_pcie_resources_2_1_0 { > struct clk *iface_clk; > struct clk *core_clk; > @@ -110,10 +136,20 @@ struct qcom_pcie_resources_2_4_0 { > struct reset_control *phy_ahb_reset; > }; > > +struct qcom_pcie_resources_2_3_3 { > + struct clk *iface; > + struct clk *axi_m_clk; > + struct clk *axi_s_clk; > + struct clk *ahb_clk; > + struct clk *aux_clk; > + struct reset_control *rst[7]; > +}; > + > union qcom_pcie_resources { > struct qcom_pcie_resources_1_0_0 v1_0_0; > struct qcom_pcie_resources_2_1_0 v2_1_0; > struct qcom_pcie_resources_2_3_2 v2_3_2; > + struct qcom_pcie_resources_2_3_3 v2_3_3; > struct qcom_pcie_resources_2_4_0 v2_4_0; > }; > > @@ -884,6 +920,169 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie) > return ret; > } > > +static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; > + struct dw_pcie *pci = pcie->pci; > + struct device *dev = pci->dev; > + int i; > + const char *rst_names[] = { "axi_m", "axi_s", "pipe", > + "axi_m_sticky", "sticky", > + "ahb", "sleep", }; > + > + res->iface = devm_clk_get(dev, "iface"); > + if (IS_ERR(res->iface)) > + return PTR_ERR(res->iface); > + > + res->axi_m_clk = devm_clk_get(dev, "axi_m"); > + if (IS_ERR(res->axi_m_clk)) > + return PTR_ERR(res->axi_m_clk); > + > + res->axi_s_clk = devm_clk_get(dev, "axi_s"); > + if (IS_ERR(res->axi_s_clk)) > + return PTR_ERR(res->axi_s_clk); > + > + res->ahb_clk = devm_clk_get(dev, "ahb"); > + if (IS_ERR(res->ahb_clk)) > + return PTR_ERR(res->ahb_clk); > + > + res->aux_clk = devm_clk_get(dev, "aux"); > + if (IS_ERR(res->aux_clk)) > + return PTR_ERR(res->aux_clk); > + > + for (i = 0; i < ARRAY_SIZE(rst_names); i++) { > + res->rst[i] = devm_reset_control_get(dev, rst_names[i]); > + if (IS_ERR(res->rst[i])) > + return PTR_ERR(res->rst[i]); > + } > + > + return 0; > +} > + > +static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; > + > + clk_disable_unprepare(res->iface); > + clk_disable_unprepare(res->axi_m_clk); > + clk_disable_unprepare(res->axi_s_clk); > + clk_disable_unprepare(res->ahb_clk); > + clk_disable_unprepare(res->aux_clk); > +} > + > +static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; > + struct dw_pcie *pci = pcie->pci; > + struct device *dev = pci->dev; > + int i, ret; > + u32 val; > + > + for (i = 0; i < ARRAY_SIZE(res->rst); i++) { > + ret = reset_control_assert(res->rst[i]); > + if (ret) { > + dev_err(pcie->pci->dev, > + "%s: reset assert failed for %d\n", > + __func__, i); > + return ret; > + } > + } > + > + usleep_range(2000, 2500); > + > + for (i = 0; i < ARRAY_SIZE(res->rst); i++) { > + ret = reset_control_deassert(res->rst[i]); > + if (ret) { > + dev_err(pcie->pci->dev, > + "%s: reset deassert failed for %d\n", > + __func__, i); > + return ret; > + } > + } > + > + /* > + * Don't have a way to see if the reset has completed. > + * Wait for some time. > + */ > + usleep_range(2000, 2500); > + > + ret = clk_prepare_enable(res->iface); > + if (ret) { > + dev_err(dev, "cannot prepare/enable core clock\n"); > + goto err_clk_iface; > + } > + > + ret = clk_prepare_enable(res->axi_m_clk); > + if (ret) { > + dev_err(dev, "cannot prepare/enable core clock\n"); > + goto err_clk_axi_m; > + } > + > + ret = clk_prepare_enable(res->axi_s_clk); > + if (ret) { > + dev_err(dev, "cannot prepare/enable axi slave clock\n"); > + goto err_clk_axi_s; > + } > + > + ret = clk_prepare_enable(res->ahb_clk); > + if (ret) { > + dev_err(dev, "cannot prepare/enable ahb clock\n"); > + goto err_clk_ahb; > + } > + > + ret = clk_prepare_enable(res->aux_clk); > + if (ret) { > + dev_err(dev, "cannot prepare/enable aux clock\n"); > + goto err_clk_aux; > + } > + > + writel(SLV_ADDR_SPACE_SZ, > + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE); > + > + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); > + val &= ~BIT(0); > + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); > + > + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); > + > + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS > + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS | > + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS, > + pcie->parf + PCIE20_PARF_SYS_CTRL); > + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH); > + > + writel(CMD_BME_VAL, pci->dbi_base + PCIE20_COMMAND_STATUS); > + writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG); > + writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1); > + > + val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); > + val &= ~PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT; > + writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); > + > + writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base + > + PCIE20_DEVICE_CONTROL2_STATUS2); > + > + return 0; > + > +err_clk_aux: > + clk_disable_unprepare(res->ahb_clk); > +err_clk_ahb: > + clk_disable_unprepare(res->axi_s_clk); > +err_clk_axi_s: > + clk_disable_unprepare(res->axi_m_clk); > +err_clk_axi_m: > + clk_disable_unprepare(res->iface); > +err_clk_iface: > + /* > + * Not checking for failure, will anyway return > + * the original failure in 'ret'. > + */ > + for (i = 0; i < ARRAY_SIZE(res->rst); i++) > + reset_control_assert(res->rst[i]); > + > + return ret; > +} > + > static int qcom_pcie_link_up(struct dw_pcie *pci) > { > u16 val = readw(pci->dbi_base + PCIE20_CAP + PCI_EXP_LNKSTA); > @@ -985,6 +1184,14 @@ static int qcom_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, > .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, > }; > > +/* Qcom IP rev.: 2.3.3 Synopsys IP rev.: 4.30a */ > +static const struct qcom_pcie_ops ops_2_3_3 = { > + .get_resources = qcom_pcie_get_resources_2_3_3, > + .init = qcom_pcie_init_2_3_3, > + .deinit = qcom_pcie_deinit_2_3_3, > + .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, > +}; > + > static const struct dw_pcie_ops dw_pcie_ops = { > .link_up = qcom_pcie_link_up, > }; > @@ -1080,6 +1287,7 @@ static int qcom_pcie_probe(struct platform_device *pdev) > { .compatible = "qcom,pcie-apq8084", .data = &ops_1_0_0 }, > { .compatible = "qcom,pcie-msm8996", .data = &ops_2_3_2 }, > { .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 }, > + { .compatible = "qcom,pcie-ipq8074", .data = &ops_2_3_3 }, Sorry forgot to mention that in the previous review, please exchange ops_2_4_0 and ops_2_3_3 to keep the list sorted.
diff --git a/drivers/pci/dwc/pcie-qcom.c b/drivers/pci/dwc/pcie-qcom.c index c4cd039..1cb03dd 100644 --- a/drivers/pci/dwc/pcie-qcom.c +++ b/drivers/pci/dwc/pcie-qcom.c @@ -37,6 +37,20 @@ #include "pcie-designware.h" #define PCIE20_PARF_SYS_CTRL 0x00 +#define MST_WAKEUP_EN BIT(13) +#define SLV_WAKEUP_EN BIT(12) +#define MSTR_ACLK_CGC_DIS BIT(10) +#define SLV_ACLK_CGC_DIS BIT(9) +#define CORE_CLK_CGC_DIS BIT(6) +#define AUX_PWR_DET BIT(4) +#define L23_CLK_RMV_DIS BIT(2) +#define L1_CLK_RMV_DIS BIT(1) + +#define PCIE20_COMMAND_STATUS 0x04 +#define CMD_BME_VAL 0x4 +#define PCIE20_DEVICE_CONTROL2_STATUS2 0x98 +#define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10 + #define PCIE20_PARF_PHY_CTRL 0x40 #define PCIE20_PARF_PHY_REFCLK 0x4C #define PCIE20_PARF_DBI_BASE_ADDR 0x168 @@ -58,9 +72,21 @@ #define CFG_BRIDGE_SB_INIT BIT(0) #define PCIE20_CAP 0x70 +#define PCIE20_CAP_LINK_CAPABILITIES (PCIE20_CAP + 0xc) +#define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT (BIT(10) | BIT(11)) +#define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14) +#define PCIE_CAP_LINK1_VAL 0x2fd7f + +#define PCIE20_PARF_Q2A_FLUSH 0x1ac + +#define PCIE20_MISC_CONTROL_1_REG 0x8bc +#define DBI_RO_WR_EN 1 #define PERST_DELAY_US 1000 +#define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358 +#define SLV_ADDR_SPACE_SZ 0x10000000 + struct qcom_pcie_resources_2_1_0 { struct clk *iface_clk; struct clk *core_clk; @@ -110,10 +136,20 @@ struct qcom_pcie_resources_2_4_0 { struct reset_control *phy_ahb_reset; }; +struct qcom_pcie_resources_2_3_3 { + struct clk *iface; + struct clk *axi_m_clk; + struct clk *axi_s_clk; + struct clk *ahb_clk; + struct clk *aux_clk; + struct reset_control *rst[7]; +}; + union qcom_pcie_resources { struct qcom_pcie_resources_1_0_0 v1_0_0; struct qcom_pcie_resources_2_1_0 v2_1_0; struct qcom_pcie_resources_2_3_2 v2_3_2; + struct qcom_pcie_resources_2_3_3 v2_3_3; struct qcom_pcie_resources_2_4_0 v2_4_0; }; @@ -884,6 +920,169 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie) return ret; } +static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; + struct dw_pcie *pci = pcie->pci; + struct device *dev = pci->dev; + int i; + const char *rst_names[] = { "axi_m", "axi_s", "pipe", + "axi_m_sticky", "sticky", + "ahb", "sleep", }; + + res->iface = devm_clk_get(dev, "iface"); + if (IS_ERR(res->iface)) + return PTR_ERR(res->iface); + + res->axi_m_clk = devm_clk_get(dev, "axi_m"); + if (IS_ERR(res->axi_m_clk)) + return PTR_ERR(res->axi_m_clk); + + res->axi_s_clk = devm_clk_get(dev, "axi_s"); + if (IS_ERR(res->axi_s_clk)) + return PTR_ERR(res->axi_s_clk); + + res->ahb_clk = devm_clk_get(dev, "ahb"); + if (IS_ERR(res->ahb_clk)) + return PTR_ERR(res->ahb_clk); + + res->aux_clk = devm_clk_get(dev, "aux"); + if (IS_ERR(res->aux_clk)) + return PTR_ERR(res->aux_clk); + + for (i = 0; i < ARRAY_SIZE(rst_names); i++) { + res->rst[i] = devm_reset_control_get(dev, rst_names[i]); + if (IS_ERR(res->rst[i])) + return PTR_ERR(res->rst[i]); + } + + return 0; +} + +static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; + + clk_disable_unprepare(res->iface); + clk_disable_unprepare(res->axi_m_clk); + clk_disable_unprepare(res->axi_s_clk); + clk_disable_unprepare(res->ahb_clk); + clk_disable_unprepare(res->aux_clk); +} + +static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; + struct dw_pcie *pci = pcie->pci; + struct device *dev = pci->dev; + int i, ret; + u32 val; + + for (i = 0; i < ARRAY_SIZE(res->rst); i++) { + ret = reset_control_assert(res->rst[i]); + if (ret) { + dev_err(pcie->pci->dev, + "%s: reset assert failed for %d\n", + __func__, i); + return ret; + } + } + + usleep_range(2000, 2500); + + for (i = 0; i < ARRAY_SIZE(res->rst); i++) { + ret = reset_control_deassert(res->rst[i]); + if (ret) { + dev_err(pcie->pci->dev, + "%s: reset deassert failed for %d\n", + __func__, i); + return ret; + } + } + + /* + * Don't have a way to see if the reset has completed. + * Wait for some time. + */ + usleep_range(2000, 2500); + + ret = clk_prepare_enable(res->iface); + if (ret) { + dev_err(dev, "cannot prepare/enable core clock\n"); + goto err_clk_iface; + } + + ret = clk_prepare_enable(res->axi_m_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable core clock\n"); + goto err_clk_axi_m; + } + + ret = clk_prepare_enable(res->axi_s_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable axi slave clock\n"); + goto err_clk_axi_s; + } + + ret = clk_prepare_enable(res->ahb_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable ahb clock\n"); + goto err_clk_ahb; + } + + ret = clk_prepare_enable(res->aux_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable aux clock\n"); + goto err_clk_aux; + } + + writel(SLV_ADDR_SPACE_SZ, + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE); + + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); + val &= ~BIT(0); + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); + + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); + + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS | + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS, + pcie->parf + PCIE20_PARF_SYS_CTRL); + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH); + + writel(CMD_BME_VAL, pci->dbi_base + PCIE20_COMMAND_STATUS); + writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG); + writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1); + + val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); + val &= ~PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT; + writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); + + writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base + + PCIE20_DEVICE_CONTROL2_STATUS2); + + return 0; + +err_clk_aux: + clk_disable_unprepare(res->ahb_clk); +err_clk_ahb: + clk_disable_unprepare(res->axi_s_clk); +err_clk_axi_s: + clk_disable_unprepare(res->axi_m_clk); +err_clk_axi_m: + clk_disable_unprepare(res->iface); +err_clk_iface: + /* + * Not checking for failure, will anyway return + * the original failure in 'ret'. + */ + for (i = 0; i < ARRAY_SIZE(res->rst); i++) + reset_control_assert(res->rst[i]); + + return ret; +} + static int qcom_pcie_link_up(struct dw_pcie *pci) { u16 val = readw(pci->dbi_base + PCIE20_CAP + PCI_EXP_LNKSTA); @@ -985,6 +1184,14 @@ static int qcom_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, }; +/* Qcom IP rev.: 2.3.3 Synopsys IP rev.: 4.30a */ +static const struct qcom_pcie_ops ops_2_3_3 = { + .get_resources = qcom_pcie_get_resources_2_3_3, + .init = qcom_pcie_init_2_3_3, + .deinit = qcom_pcie_deinit_2_3_3, + .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, +}; + static const struct dw_pcie_ops dw_pcie_ops = { .link_up = qcom_pcie_link_up, }; @@ -1080,6 +1287,7 @@ static int qcom_pcie_probe(struct platform_device *pdev) { .compatible = "qcom,pcie-apq8084", .data = &ops_1_0_0 }, { .compatible = "qcom,pcie-msm8996", .data = &ops_2_3_2 }, { .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 }, + { .compatible = "qcom,pcie-ipq8074", .data = &ops_2_3_3 }, { } };