| Message ID | 1510058999-6778-1-git-send-email-giulio.benetti@micronovasrl.com (mailing list archive) |
|---|---|
| State | Rejected, archived |
| Headers | show |
On Tue, Nov 07, 2017 at 01:49:59PM +0100, Giulio Benetti wrote: > On sun7i-a20-* there's no way to enable PA00--PA27 as RGB888 LCD0 pins. > > Add lcd_rgb888_pins in sun7i-a20.dtsi. > > It can be used on sun7i-a20-olinuxino-lime.dts. > This patch gives possibility to set parallel lcd pins for RGB888. > To be used with tcon0 in your <target>.dts My question was on which board do you want to use it right now. If the answer is none, then we won't merge that patch, we have too many pinctrl already to not add the unused ones. Maxime
Board could be any with A20, for example Olinuxino A20. Or our Q027, S027 boards, but final dts still are not complete.
Hi, On Tue, Nov 07, 2017 at 05:38:55PM +0100, Giulio Benetti wrote: > Board could be any with A20, > for example Olinuxino A20. > Or our Q027, S027 boards, but final dts still are not complete. Therefore no upstream boards are using it right now, so we'll merge it when that will be the case. Maxime
在 2017-11-08 18:56，Maxime Ripard 写道： > Hi, > > On Tue, Nov 07, 2017 at 05:38:55PM +0100, Giulio Benetti wrote: >> Board could be any with A20, >> for example Olinuxino A20. >> Or our Q027, S027 boards, but final dts still are not complete. > > Therefore no upstream boards are using it right now, so we'll merge it > when that will be the case. I think the LCD connector on Banana Pi's uses parallel interface, although the LCD should be an external DT overlay. > > Maxime > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 228c368..b85a917 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -921,6 +921,14 @@ pins = "PI20", "PI21"; function = "uart7"; }; + + lcd_rgb888_pins: lcd-rgb888 { + pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", + "PD8", "PD9", "PD10", "PD11", "PD12", "PD13", "PD14", "PD15", + "PD16", "PD17", "PD18", "PD19", "PD20", "PD21", "PD22", "PD23", + "PD24", "PD25", "PD26", "PD27"; + function = "lcd0"; + }; }; timer@1c20c00 {
On sun7i-a20-* there's no way to enable PA00--PA27 as RGB888 LCD0 pins. Add lcd_rgb888_pins in sun7i-a20.dtsi. It can be used on sun7i-a20-olinuxino-lime.dts. This patch gives possibility to set parallel lcd pins for RGB888. To be used with tcon0 in your <target>.dts Best regards Giulio Benetti Micronova srl Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com> --- arch/arm/boot/dts/sun7i-a20.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)