@@ -24,15 +24,29 @@ static struct regulator *arm_reg;
static struct regulator *pu_reg;
static struct regulator *soc_reg;
-static struct clk *arm_clk;
-static struct clk *pll1_sys_clk;
-static struct clk *pll1_sw_clk;
-static struct clk *step_clk;
-static struct clk *pll2_pfd2_396m_clk;
-
-/* clk used by i.MX6UL */
-static struct clk *pll2_bus_clk;
-static struct clk *secondary_sel_clk;
+enum IMX6_CPUFREQ_CLKS {
+ ARM,
+ PLL1_SYS,
+ STEP,
+ PLL1_SW,
+ PLL2_PFD2_396M,
+ /* MX6UL requires two more clks */
+ PLL2_BUS,
+ SECONDARY_SEL,
+};
+#define IMX6Q_CPUFREQ_CLK_NUM 5
+#define IMX6UL_CPUFREQ_CLK_NUM 7
+
+static int num_clks;
+static struct clk_bulk_data clks[] = {
+ { .id = "arm" },
+ { .id = "pll1_sys" },
+ { .id = "step" },
+ { .id = "pll1_sw" },
+ { .id = "pll2_pfd2_396m" },
+ { .id = "pll2_bus" },
+ { .id = "secondary_sel" },
+};
static struct device *cpu_dev;
static bool free_opp;
@@ -52,7 +66,7 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
new_freq = freq_table[index].frequency;
freq_hz = new_freq * 1000;
- old_freq = clk_get_rate(arm_clk) / 1000;
+ old_freq = clk_get_rate(clks[ARM].clk) / 1000;
opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_hz);
if (IS_ERR(opp)) {
@@ -111,29 +125,31 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
* voltage of 528MHz, so lower the CPU frequency to one
* half before changing CPU frequency.
*/
- clk_set_rate(arm_clk, (old_freq >> 1) * 1000);
- clk_set_parent(pll1_sw_clk, pll1_sys_clk);
- if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
- clk_set_parent(secondary_sel_clk, pll2_bus_clk);
+ clk_set_rate(clks[ARM].clk, (old_freq >> 1) * 1000);
+ clk_set_parent(clks[PLL1_SW].clk, clks[PLL1_SYS].clk);
+ if (freq_hz > clk_get_rate(clks[PLL2_PFD2_396M].clk))
+ clk_set_parent(clks[SECONDARY_SEL].clk,
+ clks[PLL2_BUS].clk);
else
- clk_set_parent(secondary_sel_clk, pll2_pfd2_396m_clk);
- clk_set_parent(step_clk, secondary_sel_clk);
- clk_set_parent(pll1_sw_clk, step_clk);
+ clk_set_parent(clks[SECONDARY_SEL].clk,
+ clks[PLL2_PFD2_396M].clk);
+ clk_set_parent(clks[STEP].clk, clks[SECONDARY_SEL].clk);
+ clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk);
} else {
- clk_set_parent(step_clk, pll2_pfd2_396m_clk);
- clk_set_parent(pll1_sw_clk, step_clk);
- if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk)) {
- clk_set_rate(pll1_sys_clk, new_freq * 1000);
- clk_set_parent(pll1_sw_clk, pll1_sys_clk);
+ clk_set_parent(clks[STEP].clk, clks[PLL2_PFD2_396M].clk);
+ clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk);
+ if (freq_hz > clk_get_rate(clks[PLL2_PFD2_396M].clk)) {
+ clk_set_rate(clks[PLL1_SYS].clk, new_freq * 1000);
+ clk_set_parent(clks[PLL1_SW].clk, clks[PLL1_SYS].clk);
} else {
/* pll1_sys needs to be enabled for divider rate change to work. */
pll1_sys_temp_enabled = true;
- clk_prepare_enable(pll1_sys_clk);
+ clk_prepare_enable(clks[PLL1_SYS].clk);
}
}
/* Ensure the arm clock divider is what we expect */
- ret = clk_set_rate(arm_clk, new_freq * 1000);
+ ret = clk_set_rate(clks[ARM].clk, new_freq * 1000);
if (ret) {
dev_err(cpu_dev, "failed to set clock rate: %d\n", ret);
regulator_set_voltage_tol(arm_reg, volt_old, 0);
@@ -142,7 +158,7 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
/* PLL1 is only needed until after ARM-PODF is set. */
if (pll1_sys_temp_enabled)
- clk_disable_unprepare(pll1_sys_clk);
+ clk_disable_unprepare(clks[PLL1_SYS].clk);
/* scaling down? scale voltage after frequency */
if (new_freq < old_freq) {
@@ -173,7 +189,7 @@ static int imx6q_cpufreq_init(struct cpufreq_policy *policy)
{
int ret;
- policy->clk = arm_clk;
+ policy->clk = clks[ARM].clk;
ret = cpufreq_generic_init(policy, freq_table, transition_latency);
policy->suspend_freq = policy->max;
@@ -213,28 +229,15 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev)
return -ENOENT;
}
- arm_clk = clk_get(cpu_dev, "arm");
- pll1_sys_clk = clk_get(cpu_dev, "pll1_sys");
- pll1_sw_clk = clk_get(cpu_dev, "pll1_sw");
- step_clk = clk_get(cpu_dev, "step");
- pll2_pfd2_396m_clk = clk_get(cpu_dev, "pll2_pfd2_396m");
- if (IS_ERR(arm_clk) || IS_ERR(pll1_sys_clk) || IS_ERR(pll1_sw_clk) ||
- IS_ERR(step_clk) || IS_ERR(pll2_pfd2_396m_clk)) {
- dev_err(cpu_dev, "failed to get clocks\n");
- ret = -ENOENT;
- goto put_clk;
- }
-
if (of_machine_is_compatible("fsl,imx6ul") ||
- of_machine_is_compatible("fsl,imx6ull")) {
- pll2_bus_clk = clk_get(cpu_dev, "pll2_bus");
- secondary_sel_clk = clk_get(cpu_dev, "secondary_sel");
- if (IS_ERR(pll2_bus_clk) || IS_ERR(secondary_sel_clk)) {
- dev_err(cpu_dev, "failed to get clocks specific to imx6ul\n");
- ret = -ENOENT;
- goto put_clk;
- }
- }
+ of_machine_is_compatible("fsl,imx6ull"))
+ num_clks = IMX6UL_CPUFREQ_CLK_NUM;
+ else
+ num_clks = IMX6Q_CPUFREQ_CLK_NUM;
+
+ ret = clk_bulk_get(cpu_dev, num_clks, clks);
+ if (ret)
+ goto put_node;
arm_reg = regulator_get(cpu_dev, "arm");
pu_reg = regulator_get_optional(cpu_dev, "pu");
@@ -378,22 +381,11 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev)
regulator_put(pu_reg);
if (!IS_ERR(soc_reg))
regulator_put(soc_reg);
-put_clk:
- if (!IS_ERR(arm_clk))
- clk_put(arm_clk);
- if (!IS_ERR(pll1_sys_clk))
- clk_put(pll1_sys_clk);
- if (!IS_ERR(pll1_sw_clk))
- clk_put(pll1_sw_clk);
- if (!IS_ERR(step_clk))
- clk_put(step_clk);
- if (!IS_ERR(pll2_pfd2_396m_clk))
- clk_put(pll2_pfd2_396m_clk);
- if (!IS_ERR(pll2_bus_clk))
- clk_put(pll2_bus_clk);
- if (!IS_ERR(secondary_sel_clk))
- clk_put(secondary_sel_clk);
+
+ clk_bulk_put(num_clks, clks);
+put_node:
of_node_put(np);
+
return ret;
}
@@ -407,13 +399,8 @@ static int imx6q_cpufreq_remove(struct platform_device *pdev)
if (!IS_ERR(pu_reg))
regulator_put(pu_reg);
regulator_put(soc_reg);
- clk_put(arm_clk);
- clk_put(pll1_sys_clk);
- clk_put(pll1_sw_clk);
- clk_put(step_clk);
- clk_put(pll2_pfd2_396m_clk);
- clk_put(pll2_bus_clk);
- clk_put(secondary_sel_clk);
+
+ clk_bulk_put(num_clks, clks);
return 0;
}
Use clk_bulk_get to ease the driver clocks handling. Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Anson Huang <anson.huang@nxp.com> Cc: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> -- The original one is here which depends on clk_bulk APIs. https://patchwork.kernel.org/patch/9737337/ Now the clk_bulk APIs are already in kernel, so resend the patch. (Patch title changed a bit to be more specific.) --- drivers/cpufreq/imx6q-cpufreq.c | 125 ++++++++++++++++++---------------------- 1 file changed, 56 insertions(+), 69 deletions(-)