new file mode 100644
@@ -0,0 +1,67 @@
+Xilinx ZynqMP DisplayPort subsystem
+-----------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
+
+- reg: Physical base address and length of the registers set for the device.
+- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical register
+ partitions.
+
+- interrupts: Interrupt number.
+- interrupts-parent: phandle for interrupt controller.
+
+- clocks: phandles for axi, audio, non-live video, and live video clocks.
+ axi clock is required. Audio clock is optional. If not present, audio will
+ be disabled. One of non-live or live video clock should be present.
+- clock-names: The identification strings are required. "aclk" for axi clock.
+ "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video clock.
+ "dp_live_video_in_clk" for live video clock (clock from programmable logic).
+
+- phys: phandles for phy specifier. The number of lanes is configurable
+ between 1 and 2. The number of phandles should be 1 or 2.
+- phy-names: The identifier strings. "dp-phy" followed by index, 0 or 1.
+ For single lane, only "dp-phy0" is required. For dual lane, both "dp-phy0"
+ and "dp-phy1" are required where "dp-phy0" is the primary lane.
+
+- power-domains: phandle for the corresponding power domain
+
+- dmas: phandles for DMA channels as defined in
+ Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: The identifier strings are required. "gfx0" for graphics layer
+ dma channel. "vid" followed by index (0 - 2) for video layer dma channels.
+
+Optional child node
+
+- The driver populates any child device node in this node. This can be used,
+ for example, to populate the sound device from the DisplayPort subsystem
+ driver.
+
+Example:
+ zynqmp-display-subsystem@fd4a0000 {
+ compatible = "xlnx,zynqmp-dpsub-1.7";
+ reg = <0x0 0xfd4a0000 0x0 0x1000>,
+ <0x0 0xfd4aa000 0x0 0x1000>,
+ <0x0 0xfd4ab000 0x0 0x1000>,
+ <0x0 0xfd4ac000 0x0 0x1000>;
+ reg-names = "dp", "blend", "av_buf", "aud";
+ interrupts = <0 119 4>;
+ interrupt-parent = <&gic>;
+
+ clock-names = "dp_apb_clk", "dp_aud_clk", "dp_live_video_in_clk";
+ clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
+
+ phys = <&lane1>, <&lane0>;
+ phy-names = "dp-phy0", "dp-phy1";
+
+ power-domains = <&pd_dp>;
+
+ dma-names = "vid0", "vid1", "vid2", "gfx0";
+ dmas = <&xlnx_dpdma 0>,
+ <&xlnx_dpdma 1>,
+ <&xlnx_dpdma 2>,
+ <&xlnx_dpdma 3>;
+ };
+};
+
This add a dt binding for ZynqMP DP subsystem. Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com> --- v4 - Specify phy related descriptions - Specify dma related descriptions - Remove ports - Remove child nodes for layers - Update the example accordingly v2 - Group multiple ports under 'ports' - Replace linux specific terms with generic hardware descriptions --- --- .../bindings/display/xlnx/xlnx,zynqmp-dpsub.txt | 67 ++++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt