| Message ID | 20180213165837.1620-2-srinivas.kandagatla@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org wrote: > From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router) > bus driver. This bus is used for communicating with DSP which provides > audio and various other services to cpu. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 ++++++++++++++++++++++ > 1 file changed, 83 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > > diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > new file mode 100644 > index 000000000000..1b95fbfed348 > --- /dev/null > +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > @@ -0,0 +1,83 @@ > +Qualcomm APR (Asynchronous Packet Router) binding > + > +This binding describes the Qualcomm APR. APR is a IPC protocol for > +communication between Application processor and QDSP. APR is mainly > +used for audio/voice services on the QDSP. > + > +- compatible: > + Usage: required > + Value type: <stringlist> > + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" > + > +- qcom,apr-dest-domain-id > + Usage: required > + Value type: <prop-encoded-array> > + Definition: Destination processor ID. > + Possible values are : > + 1 - APR simulator > + 2 - PC > + 3 - MODEM > + 4 - ADSP > + 5 - APPS > + 6 - MODEM2 > + 7 - APPS2 > + > += APR SERVICES > +Each subnode of the APR node can represent service tied to this apr. The name > +of the nodes are not important. The properties of these nodes are defined > +by the individual bindings for the specific service > +- but must contain the following property: > + > +- qcom,apr-svc-id > + Usage: required > + Value type: <prop-encoded-array> > + Definition: APR Service ID, used for matching the service. > + Possible values are : > + 3 - DSP Core Service > + 4 - Audio Front End Service. > + 5 - Voice Stream Manager Service. > + 6 - Voice processing manager. > + 7 - Audio Stream Manager Service. > + 8 - Audio Device Manager Service. > + 9 - Multimode voice manager. > + 10 - Core voice stream. > + 11 - Core voice processor. > + 12 - Ultrasound stream manager. > + 13 - Listen stream manager. > + > +- qcom,apr-svc-name > + Usage: required > + Value type: <stringlist> > + Definition: User readable name of a APR service. > + > += APR DEVICES: > +Each subnode of the APR node can represent devices tied to this apr, like > +sound-card. The properties of these nodes are defined by the individual > +bindings for the specific device. It's not a good design generally to mix different types of nodes at one level. > + > += EXAMPLE > +The following example represents a QDSP based sound card on a MSM8996 device > +which uses apr as communication between Apps and QDSP. > + > + apr { > + compatible = "qcom,apr-v2"; > + qcom,smd-channels = "apr_audio_svc"; > + qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; > + > + q6core { > + compatible = "qcom,q6core"; > + qcom,apr-svc-name = "CORE"; > + qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; > + }; > + > + q6afe { > + compatible = "qcom,q6afe"; > + qcom,apr-svc-name = "AFE"; > + qcom,apr-svc-id = <APR_SVC_AFE>; > + }; > + > + audio { > + compatible = "qcom,msm8996-snd-card"; > + ... > + }; > + }; > -- > 2.15.1 >
Thanks for the review, On 13/02/18 23:12, Rob Herring wrote: > On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org wrote: >> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> >> This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router) >> bus driver. This bus is used for communicating with DSP which provides >> audio and various other services to cpu. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> --- >> .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 ++++++++++++++++++++++ >> 1 file changed, 83 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >> >> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >> new file mode 100644 >> index 000000000000..1b95fbfed348 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >> @@ -0,0 +1,83 @@ >> +Qualcomm APR (Asynchronous Packet Router) binding >> + >> +This binding describes the Qualcomm APR. APR is a IPC protocol for >> +communication between Application processor and QDSP. APR is mainly >> +used for audio/voice services on the QDSP. >> + >> +- compatible: >> + Usage: required >> + Value type: <stringlist> >> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" >> + >> +- qcom,apr-dest-domain-id >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: Destination processor ID. >> + Possible values are : >> + 1 - APR simulator >> + 2 - PC >> + 3 - MODEM >> + 4 - ADSP >> + 5 - APPS >> + 6 - MODEM2 >> + 7 - APPS2 >> + >> += APR SERVICES >> +Each subnode of the APR node can represent service tied to this apr. The name >> +of the nodes are not important. The properties of these nodes are defined >> +by the individual bindings for the specific service >> +- but must contain the following property: >> + ... >> += APR DEVICES: >> +Each subnode of the APR node can represent devices tied to this apr, like >> +sound-card. The properties of these nodes are defined by the individual >> +bindings for the specific device. > > It's not a good design generally to mix different types of nodes at one > level. I agree, may be I can split the services and devices into different subnodes like below, which should avoid mixing different types of nodes. Does this sound good to you? apr { compatible = "qcom,apr-v2"; qcom,smd-channels = "apr_audio_svc"; qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; apr-services { q6core { qcom,apr-svc-name = "CORE"; qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; compatible = "qcom,q6core"; }; q6afe: q6afe { compatible = "qcom,q6afe"; qcom,apr-svc-name = "AFE"; qcom,apr-svc-id = <APR_SVC_AFE>; #sound-dai-cells = <1>; }; q6asm: q6asm { compatible = "qcom,q6asm"; qcom,apr-svc-name = "ASM"; qcom,apr-svc-id = <APR_SVC_ASM>; #sound-dai-cells = <1>; }; q6adm: q6adm { compatible = "qcom,q6adm"; qcom,apr-svc-name = "ADM"; qcom,apr-svc-id = <APR_SVC_ADM>; #sound-dai-cells = <0>; }; }; apr-devices { audio { compatible = "qcom,msm8996-snd-card"; ... }; }; }; > >> + >> += EXAMPLE >> +The following example represents a QDSP based sound card on a MSM8996 device >> +which uses apr as communication between Apps and QDSP. >> + >> + apr { >> + compatible = "qcom,apr-v2"; >> + qcom,smd-channels = "apr_audio_svc"; >> + qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >> + >> + q6core { >> + compatible = "qcom,q6core"; >> + qcom,apr-svc-name = "CORE"; >> + qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >> + }; >> + >> + q6afe { >> + compatible = "qcom,q6afe"; >> + qcom,apr-svc-name = "AFE"; >> + qcom,apr-svc-id = <APR_SVC_AFE>; >> + }; >> + >> + audio { >> + compatible = "qcom,msm8996-snd-card"; >> + ... >> + }; >> + }; >> -- >> 2.15.1 >>
On Wed, Feb 14, 2018 at 09:13:23AM +0000, Srinivas Kandagatla wrote: > Thanks for the review, > > On 13/02/18 23:12, Rob Herring wrote: > > On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org wrote: > > > From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > > > > > This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router) > > > bus driver. This bus is used for communicating with DSP which provides > > > audio and various other services to cpu. > > > > > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > > --- > > > .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 ++++++++++++++++++++++ > > > 1 file changed, 83 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > > > > > > diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > > > new file mode 100644 > > > index 000000000000..1b95fbfed348 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt > > > @@ -0,0 +1,83 @@ > > > +Qualcomm APR (Asynchronous Packet Router) binding > > > + > > > +This binding describes the Qualcomm APR. APR is a IPC protocol for > > > +communication between Application processor and QDSP. APR is mainly > > > +used for audio/voice services on the QDSP. > > > + > > > +- compatible: > > > + Usage: required > > > + Value type: <stringlist> > > > + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" > > > + > > > +- qcom,apr-dest-domain-id > > > + Usage: required > > > + Value type: <prop-encoded-array> > > > + Definition: Destination processor ID. > > > + Possible values are : > > > + 1 - APR simulator > > > + 2 - PC > > > + 3 - MODEM > > > + 4 - ADSP > > > + 5 - APPS > > > + 6 - MODEM2 > > > + 7 - APPS2 > > > + > > > += APR SERVICES > > > +Each subnode of the APR node can represent service tied to this apr. The name > > > +of the nodes are not important. The properties of these nodes are defined > > > +by the individual bindings for the specific service > > > +- but must contain the following property: > > > + > ... > > > += APR DEVICES: > > > +Each subnode of the APR node can represent devices tied to this apr, like > > > +sound-card. The properties of these nodes are defined by the individual > > > +bindings for the specific device. > > > > It's not a good design generally to mix different types of nodes at one > > level. > > I agree, may be I can split the services and devices into different subnodes > like below, which should avoid mixing different types of nodes. > > Does this sound good to you? Seems your original example wasn't so complete... I don't see why you need all these nodes in the first place. For a single SoC, how much does all this vary? > > apr { > compatible = "qcom,apr-v2"; > qcom,smd-channels = "apr_audio_svc"; > qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; > > apr-services { > q6core { > qcom,apr-svc-name = "CORE"; > qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; > compatible = "qcom,q6core"; > }; > > q6afe: q6afe { > compatible = "qcom,q6afe"; > qcom,apr-svc-name = "AFE"; > qcom,apr-svc-id = <APR_SVC_AFE>; > #sound-dai-cells = <1>; > }; > > q6asm: q6asm { > compatible = "qcom,q6asm"; > qcom,apr-svc-name = "ASM"; > qcom,apr-svc-id = <APR_SVC_ASM>; > #sound-dai-cells = <1>; > }; > > q6adm: q6adm { > compatible = "qcom,q6adm"; > qcom,apr-svc-name = "ADM"; > qcom,apr-svc-id = <APR_SVC_ADM>; > #sound-dai-cells = <0>; > }; All these DAI nodes could be a single node and the cell value be the svc-id? > }; > > apr-devices { > audio { > compatible = "qcom,msm8996-snd-card"; This is a pseudo device. Why not put it at the top level like other sound cards? > ... > }; > }; > }; > > > > > > > > > + > > > += EXAMPLE > > > +The following example represents a QDSP based sound card on a MSM8996 device > > > +which uses apr as communication between Apps and QDSP. > > > + > > > + apr { > > > + compatible = "qcom,apr-v2"; > > > + qcom,smd-channels = "apr_audio_svc"; > > > + qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; > > > + > > > + q6core { > > > + compatible = "qcom,q6core"; > > > + qcom,apr-svc-name = "CORE"; > > > + qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; > > > + }; > > > + > > > + q6afe { > > > + compatible = "qcom,q6afe"; > > > + qcom,apr-svc-name = "AFE"; > > > + qcom,apr-svc-id = <APR_SVC_AFE>; > > > + }; > > > + > > > + audio { > > > + compatible = "qcom,msm8996-snd-card"; > > > + ... > > > + }; > > > + }; > > > -- > > > 2.15.1 > > >
Thanks for your review comments, On 18/02/18 23:04, Rob Herring wrote: > On Wed, Feb 14, 2018 at 09:13:23AM +0000, Srinivas Kandagatla wrote: >> Thanks for the review, >> >> On 13/02/18 23:12, Rob Herring wrote: >>> On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org wrote: >>>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>> >>>> This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router) >>>> bus driver. This bus is used for communicating with DSP which provides >>>> audio and various other services to cpu. >>>> >>>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>> --- >>>> .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 ++++++++++++++++++++++ >>>> 1 file changed, 83 insertions(+) >>>> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>> >>>> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>> new file mode 100644 >>>> index 000000000000..1b95fbfed348 >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>> @@ -0,0 +1,83 @@ >>>> +Qualcomm APR (Asynchronous Packet Router) binding >>>> + >>>> +This binding describes the Qualcomm APR. APR is a IPC protocol for >>>> +communication between Application processor and QDSP. APR is mainly >>>> +used for audio/voice services on the QDSP. >>>> + >>>> +- compatible: >>>> + Usage: required >>>> + Value type: <stringlist> >>>> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" >>>> + >>>> +- qcom,apr-dest-domain-id >>>> + Usage: required >>>> + Value type: <prop-encoded-array> >>>> + Definition: Destination processor ID. >>>> + Possible values are : >>>> + 1 - APR simulator >>>> + 2 - PC >>>> + 3 - MODEM >>>> + 4 - ADSP >>>> + 5 - APPS >>>> + 6 - MODEM2 >>>> + 7 - APPS2 >>>> + >>>> += APR SERVICES >>>> +Each subnode of the APR node can represent service tied to this apr. The name >>>> +of the nodes are not important. The properties of these nodes are defined >>>> +by the individual bindings for the specific service >>>> +- but must contain the following property: >>>> + >> ... >>>> += APR DEVICES: >>>> +Each subnode of the APR node can represent devices tied to this apr, like >>>> +sound-card. The properties of these nodes are defined by the individual >>>> +bindings for the specific device. >>> >>> It's not a good design generally to mix different types of nodes at one >>> level. >> >> I agree, may be I can split the services and devices into different subnodes >> like below, which should avoid mixing different types of nodes. >> >> Does this sound good to you? > > Seems your original example wasn't so complete... > Yep, I will fix it in next version. > I don't see why you need all these nodes in the first place. For a > single SoC, how much does all this vary? > It might not vary for a given SoC, but It does vary across the SoCs. Also the versions of each service are independent to each other. >> >> apr { >> compatible = "qcom,apr-v2"; >> qcom,smd-channels = "apr_audio_svc"; >> qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >> >> apr-services { >> q6core { >> qcom,apr-svc-name = "CORE"; >> qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >> compatible = "qcom,q6core"; >> }; >> >> q6afe: q6afe { >> compatible = "qcom,q6afe"; >> qcom,apr-svc-name = "AFE"; >> qcom,apr-svc-id = <APR_SVC_AFE>; >> #sound-dai-cells = <1>; >> }; >> >> q6asm: q6asm { >> compatible = "qcom,q6asm"; >> qcom,apr-svc-name = "ASM"; >> qcom,apr-svc-id = <APR_SVC_ASM>; >> #sound-dai-cells = <1>; >> }; >> >> q6adm: q6adm { >> compatible = "qcom,q6adm"; >> qcom,apr-svc-name = "ADM"; >> qcom,apr-svc-id = <APR_SVC_ADM>; >> #sound-dai-cells = <0>; >> }; > > All these DAI nodes could be a single node and the cell value be the > svc-id? No, DAI's here are both backends and frontends, and some of the services like core, USM are not DAI's Are you also saying that we should have a single driver entity for all these services? > >> }; >> >> apr-devices { >> audio { >> compatible = "qcom,msm8996-snd-card"; > > This is a pseudo device. Why not put it at the top level like other > sound cards? APR bus depends on the state of DSP services, which can go off if the DSP crashes or DSP is stopped. If we remove this sound card out of apr bus then the sound card dependency on apr bus is totally lost. Main purpose of having sound card under this bus is that the sound card should register/unregister depending up the apr channel presence/absence respectively. thanks, srini > >> ... >> }; >> }; >> }; >> >> >> >> >>> >>>> + >>>> += EXAMPLE >>>> +The following example represents a QDSP based sound card on a MSM8996 device >>>> +which uses apr as communication between Apps and QDSP. >>>> + >>>> + apr { >>>> + compatible = "qcom,apr-v2"; >>>> + qcom,smd-channels = "apr_audio_svc"; >>>> + qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >>>> + >>>> + q6core { >>>> + compatible = "qcom,q6core"; >>>> + qcom,apr-svc-name = "CORE"; >>>> + qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >>>> + }; >>>> + >>>> + q6afe { >>>> + compatible = "qcom,q6afe"; >>>> + qcom,apr-svc-name = "AFE"; >>>> + qcom,apr-svc-id = <APR_SVC_AFE>; >>>> + }; >>>> + >>>> + audio { >>>> + compatible = "qcom,msm8996-snd-card"; >>>> + ... >>>> + }; >>>> + }; >>>> -- >>>> 2.15.1 >>>>
On Tue, Feb 20, 2018 at 3:33 AM, Srinivas Kandagatla <srinivas.kandagatla@linaro.org> wrote: > Thanks for your review comments, > > > On 18/02/18 23:04, Rob Herring wrote: >> >> On Wed, Feb 14, 2018 at 09:13:23AM +0000, Srinivas Kandagatla wrote: >>> >>> Thanks for the review, >>> >>> On 13/02/18 23:12, Rob Herring wrote: >>>> >>>> On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org >>>> wrote: >>>>> >>>>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>>> >>>>> This patch add dt bindings for Qualcomm APR (Asynchronous Packet >>>>> Router) >>>>> bus driver. This bus is used for communicating with DSP which provides >>>>> audio and various other services to cpu. >>>>> >>>>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>>> --- >>>>> .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 >>>>> ++++++++++++++++++++++ >>>>> 1 file changed, 83 insertions(+) >>>>> create mode 100644 >>>>> Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>> >>>>> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>> b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>> new file mode 100644 >>>>> index 000000000000..1b95fbfed348 >>>>> --- /dev/null >>>>> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>> @@ -0,0 +1,83 @@ >>>>> +Qualcomm APR (Asynchronous Packet Router) binding >>>>> + >>>>> +This binding describes the Qualcomm APR. APR is a IPC protocol for >>>>> +communication between Application processor and QDSP. APR is mainly >>>>> +used for audio/voice services on the QDSP. >>>>> + >>>>> +- compatible: >>>>> + Usage: required >>>>> + Value type: <stringlist> >>>>> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example >>>>> "qcom,apr-v2" >>>>> + >>>>> +- qcom,apr-dest-domain-id >>>>> + Usage: required >>>>> + Value type: <prop-encoded-array> >>>>> + Definition: Destination processor ID. >>>>> + Possible values are : >>>>> + 1 - APR simulator >>>>> + 2 - PC >>>>> + 3 - MODEM >>>>> + 4 - ADSP >>>>> + 5 - APPS >>>>> + 6 - MODEM2 >>>>> + 7 - APPS2 >>>>> + >>>>> += APR SERVICES >>>>> +Each subnode of the APR node can represent service tied to this apr. >>>>> The name >>>>> +of the nodes are not important. The properties of these nodes are >>>>> defined >>>>> +by the individual bindings for the specific service >>>>> +- but must contain the following property: >>>>> + >>> >>> ... >>>>> >>>>> += APR DEVICES: >>>>> +Each subnode of the APR node can represent devices tied to this apr, >>>>> like >>>>> +sound-card. The properties of these nodes are defined by the >>>>> individual >>>>> +bindings for the specific device. >>>> >>>> >>>> It's not a good design generally to mix different types of nodes at one >>>> level. >>> >>> >>> I agree, may be I can split the services and devices into different >>> subnodes >>> like below, which should avoid mixing different types of nodes. >>> >>> Does this sound good to you? >> >> >> Seems your original example wasn't so complete... >> > Yep, I will fix it in next version. >> >> I don't see why you need all these nodes in the first place. For a >> single SoC, how much does all this vary? >> > It might not vary for a given SoC, but It does vary across the SoCs. > Also the versions of each service are independent to each other. Not sure I follow the last statement. Meaning firmware updates change the services? I don't see any versioning of services here. > >>> >>> apr { >>> compatible = "qcom,apr-v2"; >>> qcom,smd-channels = "apr_audio_svc"; >>> qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >>> >>> apr-services { >>> q6core { >>> qcom,apr-svc-name = "CORE"; >>> qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >>> compatible = "qcom,q6core"; >>> }; >>> >>> q6afe: q6afe { >>> compatible = "qcom,q6afe"; >>> qcom,apr-svc-name = "AFE"; >>> qcom,apr-svc-id = <APR_SVC_AFE>; >>> #sound-dai-cells = <1>; >>> }; >>> >>> q6asm: q6asm { >>> compatible = "qcom,q6asm"; >>> qcom,apr-svc-name = "ASM"; >>> qcom,apr-svc-id = <APR_SVC_ASM>; >>> #sound-dai-cells = <1>; >>> }; >>> >>> q6adm: q6adm { >>> compatible = "qcom,q6adm"; >>> qcom,apr-svc-name = "ADM"; >>> qcom,apr-svc-id = <APR_SVC_ADM>; >>> #sound-dai-cells = <0>; >>> }; >> >> >> All these DAI nodes could be a single node and the cell value be the >> svc-id? > > No, DAI's here are both backends and frontends, and some of the services > like core, USM are not DAI's > > Are you also saying that we should have a single driver entity for all these > services? DT nodes do not equate driver entities. A driver can instantiate other drivers. Am I saying a single DT node for this? Yes, perhaps. > >> >>> }; >>> >>> apr-devices { >>> audio { >>> compatible = "qcom,msm8996-snd-card"; >> >> >> This is a pseudo device. Why not put it at the top level like other >> sound cards? > > > APR bus depends on the state of DSP services, which can go off if the DSP > crashes or DSP is stopped. If we remove this sound card out of apr bus then > the sound card dependency on apr bus is totally lost. > > Main purpose of having sound card under this bus is that the sound card > should register/unregister depending up the apr channel presence/absence > respectively. Okay, that seems sensible. Rob
On 22/02/18 00:14, Rob Herring wrote: > On Tue, Feb 20, 2018 at 3:33 AM, Srinivas Kandagatla > <srinivas.kandagatla@linaro.org> wrote: >> Thanks for your review comments, >> >> >> On 18/02/18 23:04, Rob Herring wrote: >>> >>> On Wed, Feb 14, 2018 at 09:13:23AM +0000, Srinivas Kandagatla wrote: >>>> >>>> Thanks for the review, >>>> >>>> On 13/02/18 23:12, Rob Herring wrote: >>>>> >>>>> On Tue, Feb 13, 2018 at 04:58:13PM +0000, srinivas.kandagatla@linaro.org >>>>> wrote: >>>>>> >>>>>> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>>>> >>>>>> This patch add dt bindings for Qualcomm APR (Asynchronous Packet >>>>>> Router) >>>>>> bus driver. This bus is used for communicating with DSP which provides >>>>>> audio and various other services to cpu. >>>>>> >>>>>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>>>>> --- >>>>>> .../devicetree/bindings/soc/qcom/qcom,apr.txt | 83 >>>>>> ++++++++++++++++++++++ >>>>>> 1 file changed, 83 insertions(+) >>>>>> create mode 100644 >>>>>> Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>>> b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>>> new file mode 100644 >>>>>> index 000000000000..1b95fbfed348 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt >>>>>> @@ -0,0 +1,83 @@ >>>>>> +Qualcomm APR (Asynchronous Packet Router) binding >>>>>> + >>>>>> +This binding describes the Qualcomm APR. APR is a IPC protocol for >>>>>> +communication between Application processor and QDSP. APR is mainly >>>>>> +used for audio/voice services on the QDSP. >>>>>> + ... >>>>> >>>>> >>>>> It's not a good design generally to mix different types of nodes at one >>>>> level. >>>> >>>> >>>> I agree, may be I can split the services and devices into different >>>> subnodes >>>> like below, which should avoid mixing different types of nodes. >>>> >>>> Does this sound good to you? >>> >>> >>> Seems your original example wasn't so complete... >>> >> Yep, I will fix it in next version. >>> >>> I don't see why you need all these nodes in the first place. For a >>> single SoC, how much does all this vary? >>> >> It might not vary for a given SoC, but It does vary across the SoCs. >> Also the versions of each service are independent to each other. > > Not sure I follow the last statement. Meaning firmware updates change > the services? Sorry for not being clear, so the services like AFE, ASM, ADM have different version numbers for a given SoC/firmware. Not 100% sure if firmware updates would change the service version number, even if it does, it can be queried dynamically on new B family SoCs, and on older A Family SoCs I have not seen the firmware updates in last 4 years. > I don't see any versioning of services here. Yes, Plan is that it will be part of the compatible string in cases where version query is not supported on older QCOM A family SoCs. On B Family SoCs we can query the version dynamically. > >> >>>> >>>> apr { >>>> compatible = "qcom,apr-v2"; >>>> qcom,smd-channels = "apr_audio_svc"; >>>> qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >>>> >>>> apr-services { >>>> q6core { >>>> qcom,apr-svc-name = "CORE"; >>>> qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >>>> compatible = "qcom,q6core"; >>>> }; >>>> >>>> q6afe: q6afe { >>>> compatible = "qcom,q6afe"; >>>> qcom,apr-svc-name = "AFE"; >>>> qcom,apr-svc-id = <APR_SVC_AFE>; >>>> #sound-dai-cells = <1>; >>>> }; >>>> >>>> q6asm: q6asm { >>>> compatible = "qcom,q6asm"; >>>> qcom,apr-svc-name = "ASM"; >>>> qcom,apr-svc-id = <APR_SVC_ASM>; >>>> #sound-dai-cells = <1>; >>>> }; >>>> >>>> q6adm: q6adm { >>>> compatible = "qcom,q6adm"; >>>> qcom,apr-svc-name = "ADM"; >>>> qcom,apr-svc-id = <APR_SVC_ADM>; >>>> #sound-dai-cells = <0>; >>>> }; >>> >>> >>> All these DAI nodes could be a single node and the cell value be the >>> svc-id? >> So we will have 2 cell values, one representing the apr service and other the dai. >> No, DAI's here are both backends and frontends, and some of the services >> like core, USM are not DAI's >> >> Are you also saying that we should have a single driver entity for all these >> services? > > DT nodes do not equate driver entities. A driver can instantiate other drivers. > > Am I saying a single DT node for this? Yes, perhaps. Yes, I will give that a go. So we will endup having something like this in DT for one frontend and backend dailink: apr { compatible = "qcom,apr-v2"; qcom,smd-channels = "apr_audio_svc"; qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP> q6audio: audiosvc { compatible = "qcom,q6audio-svc"; qcom,apr-svcs = <APR_SVC_CORE APR_SVC_AFE APR_SVC_ASM>; qcom,apr-svc-names = "CORE", "AFE", "ASM"; }; sndcard { compatible = "qcom,msm8996-snd-card" qcom,model = "DB820c"; qcom,audio-routing = "RX_BIAS", "MCLK"; fe@1 { is-fe; link-name = "MultiMedia1"; cpu { sound-dai = <&q6audio APR_SVC_ASM MM1> }; platform { sound-dai = <&q6audio APR_SVC_ASM MM1>; }; }; be@1 { link-name = "HDMI Playback"; cpu { sound-dai = <&q6audio APR_SVC_AFE HDMI>; }; platform { sound-dai = <&q6audio ARP_SVC_ADM>; }; codec { sound-dai = <&hdmi 0>; }; }; }; }; Thanks, Srini
On 22/02/18 10:03, Srinivas Kandagatla wrote: >>> Also the versions of each service are independent to each other. >> >> Not sure I follow the last statement. Meaning firmware updates change >> the services? > Sorry for not being clear, so the services like AFE, ASM, ADM have > different version numbers for a given SoC/firmware. > > Not 100% sure if firmware updates would change the service version > number, even if it does, it can be queried dynamically on new B family > SoCs, and on older A Family SoCs I have not seen the firmware updates in > last 4 years. > >> I don't see any versioning of services here. > > Yes, Plan is that it will be part of the compatible string in cases > where version query is not supported on older QCOM A family SoCs. > On B Family SoCs we can query the version dynamically. > >> >>> >>>>> >>>>> apr { >>>>> compatible = "qcom,apr-v2"; >>>>> qcom,smd-channels = "apr_audio_svc"; >>>>> qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; >>>>> >>>>> apr-services { >>>>> q6core { >>>>> qcom,apr-svc-name = "CORE"; >>>>> qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; >>>>> compatible = "qcom,q6core"; >>>>> }; >>>>> >>>>> q6afe: q6afe { >>>>> compatible = "qcom,q6afe"; >>>>> qcom,apr-svc-name = "AFE"; >>>>> qcom,apr-svc-id = <APR_SVC_AFE>; >>>>> #sound-dai-cells = <1>; >>>>> }; >>>>> >>>>> q6asm: q6asm { >>>>> compatible = "qcom,q6asm"; >>>>> qcom,apr-svc-name = "ASM"; >>>>> qcom,apr-svc-id = <APR_SVC_ASM>; >>>>> #sound-dai-cells = <1>; >>>>> }; >>>>> >>>>> q6adm: q6adm {, "external-sleep" >>>>> compatible = "qcom,q6adm"; >>>>> qcom,apr-svc-name = "ADM"; >>>>> qcom,apr-svc-id = <APR_SVC_ADM>; >>>>> #sound-dai-cells = <0>; >>>>> }; >>>> >>>> >>>> All these DAI nodes could be a single node and the cell value be the >>>> svc-id? >>> > So we will have 2 cell values, one representing the apr service and > other the dai. > >>> No, DAI's here are both backends and frontends, and some of the services >>> like core, USM are not DAI's >>> >>> Are you also saying that we should have a single driver entity for >>> all these >>> services? >> >> DT nodes do not equate driver entities. A driver can instantiate other >> drivers. >> >> Am I saying a single DT node for this? Yes, perhaps. > Yes, I will give that a go. I did try your suggestion of making audio services into a single node and it ended up more messy and non scalable. Mainly because q6afe node has more than one interface type of backend dais (child nodes). Each of this backend dai may need board specific setting ex: MI2S case where board could wire up specific tx and rx lines from 4 possible lines for that board. Also other type of dais also have some interface specific properties. MI2S example: apr { ... q6afe: q6afe { compatible = "qcom,q6afe"; qcom,apr-svc-name = "AFE"; qcom,apr-svc-id = <APR_SVC_AFE>; pinctrl-0 = <&ext_sec_tlmm_lines_act>; pinctrl-names = "default"; #sound-dai-cells = <1>; mi2s_prim_rx_dai@34{ reg = <34>; rx-lines = <0>; ... }; mi2s_prim_tx_dai@35{ reg = <35>; tx-lines = <1 2> ... }; ... }; }; Here is block diagram to give a quick overview of the components +---------+ +---------+ +---------+ | q6asm | |q6routing| | q6afe | | fedai | <------> | mixers | <-----> | bedai | +---------+ +---------+ +---------+ ^ ^ ^ | | | | +------------------+----------------+ | | | | | | v v v v v +---------+ +---------+ +---------+ | q6ASM | | q6ADM | | q6AFE | +---------+ +---------+ +---------+ ^ ^ ^ ^ | | | CPU Side | ------+---------------------+-------------------+-------- | | | |APR |APR |APR | | | | +------------------+----------------+ | | | | | | +-----+--+-----------------------------------+--+------- | | | | | QDSP Side | v v v v v v +---------+ +---------+ +---------+ | ASM | <------> | ADM | <-----> | AFE | +---------+ +---------+ +---------+ ^ | +-------------------+ | ---------------------------+-------------------------- | Audio I/O | v v +--------------------------------------------------+ | Audio devices | | CODEC | HDMI-TX | PCM | SLIMBUS | I2S |MI2S |...| | | +--------------------------------------------------+ thanks, srini
On Thu, Feb 22, 2018 at 10:03:42AM +0000, Srinivas Kandagatla wrote: > On 22/02/18 00:14, Rob Herring wrote: > > Am I saying a single DT node for this? Yes, perhaps. > Yes, I will give that a go. > > So we will endup having something like this in DT for one frontend and > backend dailink: Let's not start encoding DPCM into DT, DPCM is very much an implemntation detail of the current stack which we're gradually pushing towards replacing with something better. What we want to be doing is just treating components inside the SoC the same as components in a CODEC, the routing within a SoC being the same as in a CODEC and similarly for externally connected devices. > fe@1 { > is-fe; > link-name = "MultiMedia1"; In particular having the concept of "front end" in the DT is *very* implementation specific. We should just be describing the connections that exist in the system.
Thanks for the review, On 01/03/18 20:34, Mark Brown wrote: > On Thu, Feb 22, 2018 at 10:03:42AM +0000, Srinivas Kandagatla wrote: >> On 22/02/18 00:14, Rob Herring wrote: > >>> Am I saying a single DT node for this? Yes, perhaps. >> Yes, I will give that a go. >> >> So we will endup having something like this in DT for one frontend and >> backend dailink: > > Let's not start encoding DPCM into DT, DPCM is very much an > implemntation detail of the current stack which we're gradually pushing > towards replacing with something better. What we want to be doing is > just treating components inside the SoC the same as components in a > CODEC, the routing within a SoC being the same as in a CODEC and > similarly for externally connected devices. > >> fe@1 { >> is-fe; >> link-name = "MultiMedia1"; > > In particular having the concept of "front end" in the DT is *very* > implementation specific. We should just be describing the connections > that exist in the system. Yep, it makes sense. is-fe flag will be removed in next version, we can determine this based on codec dai, so from DT side FE or BE should not be any different. Thanks, srini >
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt new file mode 100644 index 000000000000..1b95fbfed348 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -0,0 +1,83 @@ +Qualcomm APR (Asynchronous Packet Router) binding + +This binding describes the Qualcomm APR. APR is a IPC protocol for +communication between Application processor and QDSP. APR is mainly +used for audio/voice services on the QDSP. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" + +- qcom,apr-dest-domain-id + Usage: required + Value type: <prop-encoded-array> + Definition: Destination processor ID. + Possible values are : + 1 - APR simulator + 2 - PC + 3 - MODEM + 4 - ADSP + 5 - APPS + 6 - MODEM2 + 7 - APPS2 + += APR SERVICES +Each subnode of the APR node can represent service tied to this apr. The name +of the nodes are not important. The properties of these nodes are defined +by the individual bindings for the specific service +- but must contain the following property: + +- qcom,apr-svc-id + Usage: required + Value type: <prop-encoded-array> + Definition: APR Service ID, used for matching the service. + Possible values are : + 3 - DSP Core Service + 4 - Audio Front End Service. + 5 - Voice Stream Manager Service. + 6 - Voice processing manager. + 7 - Audio Stream Manager Service. + 8 - Audio Device Manager Service. + 9 - Multimode voice manager. + 10 - Core voice stream. + 11 - Core voice processor. + 12 - Ultrasound stream manager. + 13 - Listen stream manager. + +- qcom,apr-svc-name + Usage: required + Value type: <stringlist> + Definition: User readable name of a APR service. + += APR DEVICES: +Each subnode of the APR node can represent devices tied to this apr, like +sound-card. The properties of these nodes are defined by the individual +bindings for the specific device. + += EXAMPLE +The following example represents a QDSP based sound card on a MSM8996 device +which uses apr as communication between Apps and QDSP. + + apr { + compatible = "qcom,apr-v2"; + qcom,smd-channels = "apr_audio_svc"; + qcom,apr-dest-domain-id = <APR_DOMAIN_ADSP>; + + q6core { + compatible = "qcom,q6core"; + qcom,apr-svc-name = "CORE"; + qcom,apr-svc-id = <APR_SVC_ADSP_CORE>; + }; + + q6afe { + compatible = "qcom,q6afe"; + qcom,apr-svc-name = "AFE"; + qcom,apr-svc-id = <APR_SVC_AFE>; + }; + + audio { + compatible = "qcom,msm8996-snd-card"; + ... + }; + };