diff mbox

[v2,3/8] arm64: zynqmp: Add support for Xilinx zcu102

Message ID dd5933d6a49247de4b3b7516ed7fab55d1b3eb90.1519396753.git.michal.simek@xilinx.com (mailing list archive)
State New, archived
Headers show

Commit Message

Michal Simek Feb. 23, 2018, 2:40 p.m. UTC 
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---

Changes in v2:
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers.
- Use dash in node name zcu102 rev1.0
- Record compatible string to xilinx.txt

 Documentation/devicetree/bindings/arm/xilinx.txt   |   5 +
 arch/arm64/boot/dts/xilinx/Makefile                |   3 +
 .../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts |  36 ++
 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts  | 550 +++++++++++++++++++++
 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts  |  42 ++
 5 files changed, 636 insertions(+)
 create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
 create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
 create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts

Comments

Rob Herring (Arm) March 2, 2018, 4:48 p.m. UTC | #1 
On Fri, Feb 23, 2018 at 03:40:25PM +0100, Michal Simek wrote:
> This patch is adding revA, revB and rev1.0. There are also other
> revisions between which should be backward compatible with previous
> versions. Unfortunately all revs are still in use.
> 
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
> 
> Changes in v2:
> - Remove i2c mw u-boot commands
> - Use i2c-mux instead of i2cswitch
> - Use clock generator without numbers.
> - Use dash in node name zcu102 rev1.0
> - Record compatible string to xilinx.txt
> 
>  Documentation/devicetree/bindings/arm/xilinx.txt   |   5 +
>  arch/arm64/boot/dts/xilinx/Makefile                |   3 +
>  .../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts |  36 ++
>  arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts  | 550 +++++++++++++++++++++
>  arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts  |  42 ++
>  5 files changed, 636 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts

Reviewed-by: Rob Herring <robh@kernel.org> 

but...


> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> new file mode 100644
> index 000000000000..ed3cc684931f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> @@ -0,0 +1,42 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * dts file for Xilinx ZynqMP ZCU102 RevB
> + *
> + * (C) Copyright 2016 - 2018, Xilinx, Inc.
> + *
> + * Michal Simek <michal.simek@xilinx.com>
> + */
> +
> +#include "zynqmp-zcu102-revA.dts"
> +
> +/ {
> +	model = "ZynqMP ZCU102 RevB";
> +	compatible = "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> +};
> +
> +&gem3 {
> +	phy-handle = <&phyc>;
> +	phyc: phy@c {
> +		reg = <0xc>;
> +		ti,rx-internal-delay = <0x8>;
> +		ti,tx-internal-delay = <0xa>;
> +		ti,fifo-depth = <0x1>;
> +	};
> +	/* Cleanup from RevA */
> +	/delete-node/ phy@21;
> +};
> +
> +/* Different qspi 512Mbit version */

Stray comment

> +
> +/* Fix collision with u61 */
> +&i2c0 {
> +	i2cswitch@75 {

Missed this name.

This probably creates a new node rather than going into the existing 
tree. If this compiles, we should fix it to not allow the same 
unit-address twice.

> +		i2c@2 {
> +			max15303@1b { /* u8 */
> +				compatible = "maxim,max15303";
> +				reg = <0x1b>;
> +			};
> +			/delete-node/ max15303@20;
> +		};
> +	};
> +};
> -- 
> 1.9.1
>
Michal Simek March 2, 2018, 6:39 p.m. UTC | #2 
On 2.3.2018 17:48, Rob Herring wrote:
> On Fri, Feb 23, 2018 at 03:40:25PM +0100, Michal Simek wrote:
>> This patch is adding revA, revB and rev1.0. There are also other
>> revisions between which should be backward compatible with previous
>> versions. Unfortunately all revs are still in use.
>>
>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>> ---
>>
>> Changes in v2:
>> - Remove i2c mw u-boot commands
>> - Use i2c-mux instead of i2cswitch
>> - Use clock generator without numbers.
>> - Use dash in node name zcu102 rev1.0
>> - Record compatible string to xilinx.txt
>>
>>  Documentation/devicetree/bindings/arm/xilinx.txt   |   5 +
>>  arch/arm64/boot/dts/xilinx/Makefile                |   3 +
>>  .../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts |  36 ++
>>  arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts  | 550 +++++++++++++++++++++
>>  arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts  |  42 ++
>>  5 files changed, 636 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
>>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
>>  create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> 
> Reviewed-by: Rob Herring <robh@kernel.org> 
> 
> but...
> 
> 
>> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
>> new file mode 100644
>> index 000000000000..ed3cc684931f
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
>> @@ -0,0 +1,42 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * dts file for Xilinx ZynqMP ZCU102 RevB
>> + *
>> + * (C) Copyright 2016 - 2018, Xilinx, Inc.
>> + *
>> + * Michal Simek <michal.simek@xilinx.com>
>> + */
>> +
>> +#include "zynqmp-zcu102-revA.dts"
>> +
>> +/ {
>> +	model = "ZynqMP ZCU102 RevB";
>> +	compatible = "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
>> +};
>> +
>> +&gem3 {
>> +	phy-handle = <&phyc>;
>> +	phyc: phy@c {
>> +		reg = <0xc>;
>> +		ti,rx-internal-delay = <0x8>;
>> +		ti,tx-internal-delay = <0xa>;
>> +		ti,fifo-depth = <0x1>;
>> +	};
>> +	/* Cleanup from RevA */
>> +	/delete-node/ phy@21;
>> +};
>> +
>> +/* Different qspi 512Mbit version */
> 
> Stray comment

will remove.

> 
>> +
>> +/* Fix collision with u61 */
>> +&i2c0 {
>> +	i2cswitch@75 {
> 
> Missed this name.
> 
> This probably creates a new node rather than going into the existing 
> tree. If this compiles, we should fix it to not allow the same 
> unit-address twice.

hmm interesting I didn't see that before I sent this. There is a warning
but not error.

Thanks,
Michal
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 29039b645807..2b922ec3c82a 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -21,3 +21,8 @@  Additional compatible strings:
 
 - Xilinx 96boards compatible board zcu100
   "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100"
+
+- Xilinx evaluation board zcu102
+  "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102"
+  "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102"
+  "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 7266a6a9c0cd..24e3ce801304 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -1,3 +1,6 @@ 
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
new file mode 100644
index 000000000000..6647e97edba3
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
@@ -0,0 +1,36 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 Rev1.0
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-revB.dts"
+
+/ {
+	model = "ZynqMP ZCU102 Rev1.0";
+	compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
+
+&eeprom {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	board_sn: board-sn@0 {
+		reg = <0x0 0x14>;
+	};
+
+	eth_mac: eth-mac@20 {
+		reg = <0x20 0x6>;
+	};
+
+	board_name: board-name@d0 {
+		reg = <0xd0 0x6>;
+	};
+
+	board_revision: board-revision@e0 {
+		reg = <0xe0 0x3>;
+	};
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
new file mode 100644
index 000000000000..53f189fca9b1
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -0,0 +1,550 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 RevA
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "ZynqMP ZCU102 RevA";
+	compatible = "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		gpio0 = &gpio;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+		sw19 {
+			label = "sw19";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_DOWN>;
+			gpio-key,wakeup;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: phy@21 {
+		reg = <21>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tca6416_u97: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * IRQ not connected
+		 * Lines:
+		 * 0 - PS_GTR_LAN_SEL0
+		 * 1 - PS_GTR_LAN_SEL1
+		 * 2 - PS_GTR_LAN_SEL2
+		 * 3 - PS_GTR_LAN_SEL3
+		 * 4 - PCI_CLK_DIR_SEL
+		 * 5 - IIC_MUX_RESET_B
+		 * 6 - GEM3_EXP_RESET_B
+		 * 7, 10 - 17 - not connected
+		 */
+
+		gtr_sel0 {
+			gpio-hog;
+			gpios = <0 0>;
+			output-low; /* PCIE = 0, DP = 1 */
+			line-name = "sel0";
+		};
+		gtr_sel1 {
+			gpio-hog;
+			gpios = <1 0>;
+			output-high; /* PCIE = 0, DP = 1 */
+			line-name = "sel1";
+		};
+		gtr_sel2 {
+			gpio-hog;
+			gpios = <2 0>;
+			output-high; /* PCIE = 0, USB0 = 1 */
+			line-name = "sel2";
+		};
+		gtr_sel3 {
+			gpio-hog;
+			gpios = <3 0>;
+			output-high; /* PCIE = 0, SATA = 1 */
+			line-name = "sel3";
+		};
+	};
+
+	tca6416_u61: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * IRQ not connected
+		 * Lines:
+		 * 0 - VCCPSPLL_EN
+		 * 1 - MGTRAVCC_EN
+		 * 2 - MGTRAVTT_EN
+		 * 3 - VCCPSDDRPLL_EN
+		 * 4 - MIO26_PMU_INPUT_LS
+		 * 5 - PL_PMBUS_ALERT
+		 * 6 - PS_PMBUS_ALERT
+		 * 7 - MAXIM_PMBUS_ALERT
+		 * 10 - PL_DDR4_VTERM_EN
+		 * 11 - PL_DDR4_VPP_2V5_EN
+		 * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
+		 * 13 - PS_DIMM_SUSPEND_EN
+		 * 14 - PS_DDR4_VTERM_EN
+		 * 15 - PS_DDR4_VPP_2V5_EN
+		 * 16 - 17 - not connected
+		 */
+	};
+
+	i2c-mux@75 { /* u60 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			ina226@40 { /* u76 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			ina226@41 { /* u77 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			ina226@42 { /* u78 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			ina226@43 { /* u87 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			ina226@44 { /* u85 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			ina226@45 { /* u86 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			ina226@46 { /* u93 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			ina226@47 { /* u88 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			ina226@4a { /* u15 */
+				compatible = "ti,ina226";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			ina226@4b { /* u92 */
+				compatible = "ti,ina226";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* PL_PMBUS */
+			ina226@40 { /* u79 */
+				compatible = "ti,ina226";
+				reg = <0x40>;
+				shunt-resistor = <2000>;
+			};
+			ina226@41 { /* u81 */
+				compatible = "ti,ina226";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			ina226@42 { /* u80 */
+				compatible = "ti,ina226";
+				reg = <0x42>;
+				shunt-resistor = <5000>;
+			};
+			ina226@43 { /* u84 */
+				compatible = "ti,ina226";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			ina226@44 { /* u16 */
+				compatible = "ti,ina226";
+				reg = <0x44>;
+				shunt-resistor = <5000>;
+			};
+			ina226@45 { /* u65 */
+				compatible = "ti,ina226";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			ina226@46 { /* u74 */
+				compatible = "ti,ina226";
+				reg = <0x46>;
+				shunt-resistor = <5000>;
+			};
+			ina226@47 { /* u75 */
+				compatible = "ti,ina226";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* MAXIM_PMBUS - 00 */
+			max15301@a { /* u46 */
+				compatible = "maxim,max15301";
+				reg = <0xa>;
+			};
+			max15303@b { /* u4 */
+				compatible = "maxim,max15303";
+				reg = <0xb>;
+			};
+			max15303@10 { /* u13 */
+				compatible = "maxim,max15303";
+				reg = <0x10>;
+			};
+			max15301@13 { /* u47 */
+				compatible = "maxim,max15301";
+				reg = <0x13>;
+			};
+			max15303@14 { /* u7 */
+				compatible = "maxim,max15303";
+				reg = <0x14>;
+			};
+			max15303@15 { /* u6 */
+				compatible = "maxim,max15303";
+				reg = <0x15>;
+			};
+			max15303@16 { /* u10 */
+				compatible = "maxim,max15303";
+				reg = <0x16>;
+			};
+			max15303@17 { /* u9 */
+				compatible = "maxim,max15303";
+				reg = <0x17>;
+			};
+			max15301@18 { /* u63 */
+				compatible = "maxim,max15301";
+				reg = <0x18>;
+			};
+			max15303@1a { /* u49 */
+				compatible = "maxim,max15303";
+				reg = <0x1a>;
+			};
+			max15303@1d { /* u18 */
+				compatible = "maxim,max15303";
+				reg = <0x1d>;
+			};
+			max15303@20 { /* u8 */
+				compatible = "maxim,max15303";
+				status = "disabled"; /* unreachable */
+				reg = <0x20>;
+			};
+
+			max20751@72 { /* u95 */
+				compatible = "maxim,max20751";
+				reg = <0x72>;
+			};
+			max20751@73 { /* u96 */
+				compatible = "maxim,max20751";
+				reg = <0x73>;
+			};
+		};
+		/* Bus 3 is not connected */
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* PL i2c via PCA9306 - u45 */
+	i2c-mux@74 { /* u34 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u23 */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si5341: clock-generator@36 { /* SI5341 - u69 */
+				reg = <0x36>;
+			};
+
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER SI570 - u42 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+			};
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>; /* copy from zc702 */
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+			};
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			si5328: clock-generator@69 {/* SI5328 - u20 */
+				reg = <0x69>;
+				/*
+				 * Chip has interrupt present connected to PL
+				 * interrupt-parent = <&>;
+				 * interrupts = <>;
+				 */
+			};
+		};
+		/* 5 - 7 unconnected */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u135 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* HPC0_IIC */
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* HPC1_IIC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SEP 3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SEP 2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SEP 1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SEP 0 */
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	no-1-8-v;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+};
+
+&watchdog0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
new file mode 100644
index 000000000000..ed3cc684931f
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -0,0 +1,42 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 RevB
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-revA.dts"
+
+/ {
+	model = "ZynqMP ZCU102 RevB";
+	compatible = "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
+
+&gem3 {
+	phy-handle = <&phyc>;
+	phyc: phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+	};
+	/* Cleanup from RevA */
+	/delete-node/ phy@21;
+};
+
+/* Different qspi 512Mbit version */
+
+/* Fix collision with u61 */
+&i2c0 {
+	i2cswitch@75 {
+		i2c@2 {
+			max15303@1b { /* u8 */
+				compatible = "maxim,max15303";
+				reg = <0x1b>;
+			};
+			/delete-node/ max15303@20;
+		};
+	};
+};