| Message ID | 20180410205643.GA2228@lenoch (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Ladis, On Tue, 10 Apr 2018 22:56:43 +0200 Ladislav Michl <ladis@linux-mips.org> wrote: > Hi Nikolaus, > > On Tue, Apr 10, 2018 at 06:25:17PM +0200, H. Nikolaus Schaller wrote: > > Hi, > > we just started testing the v4.16 kernel and found the > > device no longer bootable (works with v4.15). It turned > > out that there was a harmful modification somewhere between > > v4.15.0 and v4.16-rc1. > > > > A git bisect points to this patch: > > Well, that's a shame... However, this code is in production for several > months now, so could you, please put 'goto out_copy' if 'buf >= high_memory' > condition is met, ie: > --- a/drivers/mtd/nand/onenand/omap2.c > +++ b/drivers/mtd/nand/onenand/omap2.c > @@ -392,6 +392,7 @@ static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, > if (buf >= high_memory) { > struct page *p1; > > + goto out_copy; > if (((size_t)buf & PAGE_MASK) != > ((size_t)(buf + count - 1) & PAGE_MASK)) > goto out_copy; I had the same problem here, and that snippet helps here. ubiattach -p /dev/mtdX does not cause kernel oopses here anymore Regards, Andreas
Hi Ladislav, > Am 10.04.2018 um 22:56 schrieb Ladislav Michl <ladis@linux-mips.org>: > > Hi Nikolaus, > > On Tue, Apr 10, 2018 at 06:25:17PM +0200, H. Nikolaus Schaller wrote: >> Hi, >> we just started testing the v4.16 kernel and found the >> device no longer bootable (works with v4.15). It turned >> out that there was a harmful modification somewhere between >> v4.15.0 and v4.16-rc1. >> >> A git bisect points to this patch: > > Well, that's a shame... However, this code is in production for several > months now, Well, we could have tested earlier release-candidates... > so could you, please put 'goto out_copy' if 'buf >= high_memory' > condition is met, ie: > --- a/drivers/mtd/nand/onenand/omap2.c > +++ b/drivers/mtd/nand/onenand/omap2.c > @@ -392,6 +392,7 @@ static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, > if (buf >= high_memory) { > struct page *p1; > > + goto out_copy; > if (((size_t)buf & PAGE_MASK) != > ((size_t)(buf + count - 1) & PAGE_MASK)) > goto out_copy; > and in case it does not help put the same goto at the very beginning of > omap2_onenand_read_bufferram function and report result? Yes, works for me. Device boots and I can mount the NAND to inspect the ubifs. Only omap2_onenand_write_bufferram has the same problem, but that is to be expected. I'll try you new patch now. > > Thank you for cooperation, > ladis Thanks for the quick reply and analysis. BR, Nikolaus > >> commit bdaca9345d41fd9420995469d27603ea62054691 >> Author: Ladislav Michl <ladis@linux-mips.org> >> Date: Fri Jan 12 14:16:57 2018 +0100 >> >> mtd: onenand: omap2: Decouple DMA enabling from INT pin availability >> >> INT pin (gpio_irq) is not really needed for DMA but only for notification >> when a command that needs wait has completed. DMA memcpy can be still used >> even without gpio_irq available, so enable it unconditionally. >> >> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> >> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> >> Tested-by: Tony Lindgren <tony@atomide.com> >> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> >> Acked-by: Roger Quadros <rogerq@ti.com> >> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> >> >> Kernel panic log is attached which indeed indicates a DMA problem. >> >> Note that we have added compatible = "ti,omap2-onenand"; >> >> Any suggestions, fixes? >> >> BR and thanks, >> Nikolaus Schaller >> >> >> >> ## Booting kernel from Legacy Image at 82000000 ... >> Image Name: Linux-4.16.0-letux+ >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 4456744 Bytes = 4.3 MiB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> ## Flattened Device Tree blob at 81c00000 >> Booting using the fdt blob at 0x81c00000 >> Loading Kernel Image ... OK >> Using Device Tree in place at 81c00000, end 81c14a1e >> >> Starting kernel ... >> >> [ 0.000000] Booting Linux on physical CPU 0x0 >> [ 0.000000] Linux version 4.16.0-letux+ (hns@iMac.local) (gcc version 4.9.2 (GCC)) #2187 SMP PREEMPT Tue Apr 10 16:23:45 CEST 2018 >> [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d >> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache >> [ 0.000000] OF: fdt: Machine model: Goldelico GTA04A5/Letux 2804 >> [ 0.000000] debug: ignoring loglevel setting. >> [ 0.000000] Memory policy: Data cache writeback >> [ 0.000000] cma: Reserved 16 MiB at 0xbe800000 >> [ 0.000000] On node 0 totalpages: 261632 >> [ 0.000000] Normal zone: 1536 pages used for memmap >> [ 0.000000] Normal zone: 0 pages reserved >> [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 >> [ 0.000000] HighMem zone: 65024 pages, LIFO batch:15 >> [ 0.000000] CPU: All CPU(s) started in SVC mode. >> [ 0.000000] OMAP3630/DM3730 ES1.2 (l2cache iva sgx neon isp 192mhz_clk) >> [ 0.000000] random: fast init done >> [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39744 r8192 d21696 u69632 >> [ 0.000000] pcpu-alloc: s39744 r8192 d21696 u69632 alloc=17*4096 >> [ 0.000000] pcpu-alloc: [0] 0 >> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260096 >> [ 0.000000] Kernel command line: console=ttyO2,115200n8 mtdoops.mtddev=omap2.nand ubi.mtd=4 root=/dev/mmcblk0p1 rw rootfstype=ext4,ext3 rootwait console=ttyO2,115200n8 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 log_buf_len=8M ignore_loglevel earlyprintk >> [ 0.000000] log_buf_len: 8388608 bytes >> [ 0.000000] early log buf free: 63924(97%) >> [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >> [ 0.000000] Memory: 1002524K/1046528K available (6169K kernel code, 626K rwdata, 1660K rodata, 1024K init, 218K bss, 27620K reserved, 16384K cma-reserved, 243712K highmem) >> [ 0.000000] Virtual kernel memory layout: >> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >> [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) >> [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) >> [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) >> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) >> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) >> [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (7162 kB) >> [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) >> [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 627 kB) >> [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 219 kB) >> [ 0.000000] Preemptible hierarchical RCU implementation. >> [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. >> [ 0.000000] Tasks RCU enabled. >> [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 >> [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 >> [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 4.0) with 96 interrupts >> [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz >> [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz >> [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns >> [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns >> [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz >> [ 0.001159] Console: colour dummy device 80x30 >> [ 0.001220] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) >> [ 0.117279] pid_max: default: 32768 minimum: 301 >> [ 0.117462] Security Framework initialized >> [ 0.117553] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) >> [ 0.117584] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) >> [ 0.118499] CPU: Testing write buffer coherency: ok >> [ 0.118988] CPU0: thread -1, cpu 0, socket -1, mpidr 0 >> [ 0.157257] Setting up static identity map for 0x80100000 - 0x80100060 >> [ 0.177124] Hierarchical SRCU implementation. >> [ 0.217041] smp: Bringing up secondary CPUs ... >> [ 0.217071] smp: Brought up 1 node, 1 CPU >> [ 0.217102] SMP: Total of 1 processors activated (597.60 BogoMIPS). >> [ 0.217102] CPU: All CPU(s) started in SVC mode. >> [ 0.219177] devtmpfs: initialized >> [ 0.247558] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 >> [ 0.248321] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns >> [ 0.248352] futex hash table entries: 256 (order: 2, 16384 bytes) >> [ 0.249816] pinctrl core: initialized pinctrl subsystem >> [ 0.251129] NET: Registered protocol family 16 >> [ 0.254211] DMA: preallocated 256 KiB pool for atomic coherent allocations >> [ 0.285614] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp >> [ 0.286437] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp >> [ 0.367187] audit: initializing netlink subsys (disabled) >> [ 0.369598] audit: type=2000 audit(0.370:1): state=initialized audit_enabled=0 res=1 >> [ 0.376861] cpuidle: using governor menu >> [ 0.377777] Reprogramming SDRC clock to 400000000 Hz >> [ 0.388366] OMAP GPIO hardware version 2.5 >> [ 0.397277] GPIO line 143 (irda_en) hogged as output/high >> [ 0.430053] omap-gpmc 6e000000.gpmc: could not find pctldev for node /ocp@68000000/l4@48000000/scm@2000/pinmux@30/pinmux_gpmc_pins, deferring probe >> [ 0.453155] No ATAGs? >> [ 0.453155] hw-breakpoint: debug architecture 0x4 unsupported. >> [ 0.454315] omap4_sram_init:Unable to allocate sram needed to handle errata I688 >> [ 0.454345] omap4_sram_init:Unable to get sram pool needed to handle errata I688 >> [ 0.454711] OMAP DMA hardware revision 5.0 >> [ 0.553466] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) >> [ 0.558044] reg-fixed-voltage wlan_en_regulator: could not find pctldev for node /ocp@68000000/l4@48000000/scm@2000/pinmux@30/pinmux_wlan_pins, deferring probe >> [ 0.558135] reg-fixed-voltage bt_en_regulator: could not find pctldev for node /ocp@68000000/l4@48000000/scm@2000/pinmux@30/pinmux_bt_pins, deferring probe >> [ 0.567810] omap-iommu 480bd400.mmu: 480bd400.mmu registered >> [ 0.569183] iommu: Adding device 480bc000.isp to group 0 >> [ 0.573181] SCSI subsystem initialized >> [ 0.573822] libata version 3.00 loaded. >> [ 0.574768] usbcore: registered new interface driver usbfs >> [ 0.574951] usbcore: registered new interface driver hub >> [ 0.575195] usbcore: registered new device driver usb >> [ 0.575897] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator >> [ 0.581481] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz >> [ 0.585662] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz >> [ 0.588562] omap_i2c 48060000.i2c: bus 2 rev4.4 at 100 kHz >> [ 0.590576] Advanced Linux Sound Architecture Driver Initialized. >> [ 0.595062] clocksource: Switched to clocksource 32k_counter >> [ 0.680328] VFS: Disk quotas dquot_6.6.0 >> [ 0.680480] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> [ 0.713348] NET: Registered protocol family 2 >> [ 0.714935] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) >> [ 0.714965] TCP established hash table entries: 8192 (order: 3, 32768 bytes) >> [ 0.715087] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) >> [ 0.716766] TCP: Hash tables configured (established 8192 bind 8192) >> [ 0.716979] UDP hash table entries: 512 (order: 2, 16384 bytes) >> [ 0.717041] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) >> [ 0.717285] NET: Registered protocol family 1 >> [ 0.721435] hw perfevents: no interrupt-affinity property for /pmu@54000000, guessing. >> [ 0.722167] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available >> [ 0.733459] Initialise system trusted keyrings >> [ 0.734985] workingset: timestamp_bits=30 max_order=18 bucket_order=0 >> [ 0.735992] squashfs: version 4.0 (2009/01/31) Phillip Lougher >> [ 0.740325] Key type asymmetric registered >> [ 0.740356] Asymmetric key parser 'x509' registered >> [ 0.740447] bounce: pool size: 64 pages >> [ 0.740600] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) >> [ 0.740600] io scheduler noop registered >> [ 0.740631] io scheduler deadline registered >> [ 0.740692] io scheduler cfq registered (default) >> [ 0.740722] io scheduler mq-deadline registered >> [ 0.740722] io scheduler kyber registered >> [ 0.748992] pinctrl-single 48002030.pinmux: 284 pins, size 568 >> [ 0.750823] pinctrl-single 48002a00.pinmux: 46 pins, size 92 >> [ 0.751983] pinctrl-single 480025a0.pinmux: 46 pins, size 92 >> [ 0.752716] pinctrl-single 480022d8.pinmux: please update dts to use #pinctrl-cells = <2> >> [ 0.752838] pinctrl-single 480022d8.pinmux: initialized with no interrupts >> [ 0.752868] pinctrl-single 480022d8.pinmux: 4 pins, size 4 >> [ 0.753448] pinctrl-single 48002274.pinmux: please update dts to use #pinctrl-cells = <2> >> [ 0.753570] pinctrl-single 48002274.pinmux: initialized with no interrupts >> [ 0.753601] pinctrl-single 48002274.pinmux: 4 pins, size 4 >> [ 0.765106] omap_uart 4806a000.serial: no wakeirq for uart0 >> [ 0.765808] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 >> [ 0.766876] serial serial0: tty port ttyO0 registered >> [ 0.767456] omap_uart 4806c000.serial: no wakeirq for uart1 >> [ 0.767669] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 >> [ 0.768402] serial serial1: tty port ttyO1 registered >> [ 0.769042] omap_uart 49020000.serial: no wakeirq for uart2 >> [ 0.769378] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 >> [ 1.675048] console [ttyO2] enabled >> [ 1.680389] omap_uart 49042000.serial: no wakeirq for uart3 >> [ 1.687011] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3 >> [ 1.720733] brd: module loaded >> [ 1.737548] loop: module loaded >> [ 1.768859] twl 0-0048: PIH (irq 23) chaining IRQs 145..153 >> [ 1.774841] twl 0-0048: power (irq 150) chaining IRQs 153..160 >> [ 1.790344] VAUX3: Bringing 2800000uV into 2500000-2500000uV >> [ 1.814697] VMMC2: Bringing 2600000uV into 1800000-1800000uV >> [ 1.822174] VMMC2: failed to apply 1800000-1800000uV constraint(-22) >> [ 1.829162] twl4030_reg 48070000.i2c:twl@48:regulator-vmmc2: can't register VMMC2, -22 >> [ 1.837707] twl4030_reg: probe of 48070000.i2c:twl@48:regulator-vmmc2 failed with error -22 >> [ 1.856262] VSIM: Bringing 1800000uV into 2800000-2800000uV >> [ 1.899414] libphy: Fixed MDIO Bus: probed >> [ 1.912872] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> [ 1.920806] usbcore: registered new interface driver usb-storage >> [ 1.928375] mousedev: PS/2 mouse device common for all mice >> [ 1.937164] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. >> [ 1.944396] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC >> [ 1.953063] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48:rtc as rtc0 >> [ 1.963684] i2c /dev entries driver >> [ 1.968963] IR NEC protocol handler initialized >> [ 1.973693] IR RC5(x/sz) protocol handler initialized >> [ 1.979553] IR RC6 protocol handler initialized >> [ 1.984313] IR JVC protocol handler initialized >> [ 1.989166] IR Sony protocol handler initialized >> [ 1.994018] IR SANYO protocol handler initialized >> [ 1.999114] IR Sharp protocol handler initialized >> [ 2.004058] IR MCE Keyboard/mouse protocol handler initialized >> [ 2.010223] IR XMP protocol handler initialized >> [ 2.014984] Driver for 1-wire Dallas network protocol. >> [ 2.022155] ti-soc-thermal 48002524.bandgap: This OMAP thermal sensor is unreliable. You've been warned >> [ 2.032592] ti-soc-thermal 48002524.bandgap: Non-trimmed BGAP, Temp not accurate >> [ 2.043121] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> [ 2.103393] ledtrig-cpu: registered to indicate activity on CPUs >> [ 2.111541] usbcore: registered new interface driver usbhid >> [ 2.119415] usbhid: USB HID core driver >> [ 2.123901] ashmem: initialized >> [ 2.131225] oprofile: using arm/armv7 >> [ 2.135131] mmc0: host does not support reading read-only switch, assuming write-enable >> [ 2.144989] Initializing XFRM netlink socket >> [ 2.149841] mmc0: new high speed SDHC card at address b368 >> [ 2.155792] NET: Registered protocol family 17 >> [ 2.160491] NET: Registered protocol family 15 >> [ 2.166320] mmcblk0: mmc0:b368 USD 7.47 GiB >> [ 2.172180] Key type dns_resolver registered >> [ 2.178070] omap2_set_init_voltage: unable to find boot up OPP for vdd_core >> [ 2.185546] omap2_set_init_voltage: unable to set vdd_core >> [ 2.192779] mmcblk0: p1 >> [ 2.196899] ThumbEE CPU extension supported. >> [ 2.201385] Registering SWP/SWPB emulation handler >> [ 2.207519] SmartReflex Class3 initialized >> [ 2.212921] Loading compiled-in X.509 certificates >> [ 2.234527] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 >> [ 2.240295] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 >> [ 2.248382] omap2-onenand 4000000.onenand: initializing on CS0 (0x04000000), va 5c982521, DMA mode >> [ 2.258270] OneNAND Manufacturer: Samsung (0xec) >> [ 2.263092] Muxed OneNAND 512MB 1.8V 16-bit (0x50) >> [ 2.268188] OneNAND version = 0x0232 >> [ 2.271942] Chip support all block unlock >> [ 2.276153] Chip has 4KiB pagesize >> [ 2.279724] Chip has cache program feature >> [ 2.285552] Scanning device for bad blocks >> [ 2.393066] onenand_bbt_wait: ecc 0xaaaa ctrl 0x0400 intr 0x8080 addr1 0x34b addr8 0x0 >> [ 2.401367] OneNAND eraseblock 843 is an initial bad block >> [ 2.554351] omap2-onenand 4000000.onenand: optimized timings for 83 MHz >> [ 2.561340] 5 ofpart partitions found on MTD device 4000000.onenand >> [ 2.567932] Creating 5 MTD partitions on "4000000.onenand": >> [ 2.573730] 0x000000000000-0x000000080000 : "X-Loader" >> [ 2.580718] 0x000000080000-0x000000240000 : "U-Boot" >> [ 2.587799] 0x000000240000-0x000000280000 : "U-Boot Env" >> [ 2.595153] 0x000000280000-0x000000880000 : "Kernel" >> [ 2.602325] 0x000000880000-0x000020000000 : "File System" >> [ 2.732788] ubi0: default fastmap pool size: 100 >> [ 2.739837] ubi0: default fastmap WL pool size: 50 >> [ 2.744903] ubi0: attaching mtd4 >> [ 2.751831] omap_hsmmc 480b4000.mmc: card claims to support voltages below defined range >> [ 2.788055] mmc1: new high speed SDIO card at address 0001 >> [ 2.910888] ubi0: scanning is finished >> [ 2.915283] Unable to handle kernel NULL pointer dereference at virtual address 00000000 >> [ 2.923767] pgd = 3b4ffe8c >> [ 2.926635] [00000000] *pgd=00000000 >> [ 2.930389] Internal error: Oops: 805 [#1] PREEMPT SMP ARM >> [ 2.936126] Modules linked in: >> [ 2.939300] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.16.0-letux+ #2187 >> [ 2.946411] Hardware name: Generic OMAP36xx (Flattened Device Tree) >> [ 2.952972] PC is at v7_dma_inv_range+0x30/0x48 >> [ 2.957733] LR is at dma_cache_maint_page+0xd0/0xe0 >> [ 2.962799] pc : [<c0118abc>] lr : [<c0113330>] psr: 60000113 >> [ 2.969360] sp : ee0afca8 ip : c0118b3c fp : c0a03d54 >> [ 2.974822] r10: 00000002 r9 : 00001000 r8 : c0abcb00 >> [ 2.980255] r7 : c0a06b84 r6 : 000c0000 r5 : 00001000 r4 : 00000000 >> [ 2.987091] r3 : 0000003f r2 : 00000040 r1 : 00001000 r0 : 00000000 >> [ 2.993896] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none >> [ 3.001342] Control: 10c5387d Table: 80004019 DAC: 00000051 >> [ 3.007354] Process swapper/0 (pid: 1, stack limit = 0xb7652d0f) >> [ 3.013641] Stack: (0xee0afca8 to 0xee0b0000) >> [ 3.018188] fca0: efff9000 00000000 00001000 00000000 00001000 efff9000 >> [ 3.026733] fcc0: 00000002 00000000 ee6f7aa8 02c41000 04000000 c0113360 c0118b3c 00000000 >> [ 3.035278] fce0: 00001000 efff9000 00000000 ee6f4810 00001000 c0113444 00000400 00000000 >> [ 3.043792] fd00: ee6f7820 c0515110 00000002 00000000 f0957000 c0514fc0 ee6f7820 ee0afdc8 >> [ 3.052368] fd20: 00000000 00001000 ee6f7aa8 02c41000 00000000 c0511f94 00001000 ee731580 >> [ 3.060913] fd40: 00006000 f0957000 00001000 00000000 00000000 00000000 00000000 00000080 >> [ 3.069458] fd60: 00000000 00000000 00000000 00000fff 00007000 ee724400 00000000 00000000 >> [ 3.078002] fd80: ee0afe24 00880000 00000000 ee0afdc8 00000000 c04f86b0 ee0afdc8 00000000 >> [ 3.086547] fda0: 023c1000 00000000 00006000 ee724400 c04f867c c04f6588 ee0afdc8 c0acad34 >> [ 3.095092] fdc0: c022f98c ee71f440 00000000 00006000 00000000 00000000 00000000 00000000 >> [ 3.103637] fde0: f0957000 00000000 ee71f440 ee387000 00006000 0000008f 00001000 023c1000 >> [ 3.112182] fe00: 00000000 f0957000 00000004 c051ebb8 00006000 ee0afe24 f0957000 c022fad0 >> [ 3.120727] fe20: 014080c0 00000000 00000000 ee387000 ee7366f0 ee72fa80 ee0afe68 ee736710 >> [ 3.129272] fe40: 00000014 c0acad34 00000000 c051643c 00006000 c0acad34 00000000 c023ad90 >> [ 3.137817] fe60: f0957000 00000000 ee387000 00000000 ee387000 00000000 ee724400 ee387040 >> [ 3.146362] fe80: 00000014 c0acad34 00000000 c0524e60 ee387000 ee72fa80 00000000 ee387000 >> [ 3.154907] fea0: 00000000 ee387040 00000014 c051996c c0acad34 00000000 c0acad34 c095483c >> [ 3.163482] fec0: ee724400 00000004 000000bc 00000000 c0acad38 ee724400 c0acad34 00000000 >> [ 3.171997] fee0: c0a9c900 c095483c 00000000 c093b4f0 00000000 00000000 c0a06ca0 c0acad39 >> [ 3.180541] ff00: 00000007 c093b3b8 000000bc c09705f4 00000000 c0102818 000000bb c08a5ca0 >> [ 3.189086] ff20: 00000000 c014973c 00000000 c08a4e04 00000007 00000007 c08a5cb4 efffcad4 >> [ 3.197662] ff40: 000000bb c08a5cb4 efffcad4 00000000 c095483c 00000007 c0954834 000000bc >> [ 3.206207] ff60: 00000007 c0954838 000000bc c09705f4 c0a9c900 c0900d78 00000007 00000007 >> [ 3.214752] ff80: 00000000 c090058c 00000000 c06ff350 00000000 00000000 00000000 00000000 >> [ 3.223297] ffa0: 00000000 c06ff358 00000000 c01010e8 00000000 00000000 00000000 00000000 >> [ 3.231842] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 >> [ 3.240386] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffdfffff fffffd7f >> [ 3.248962] [<c0118abc>] (v7_dma_inv_range) from [<c0113330>] (dma_cache_maint_page+0xd0/0xe0) >> [ 3.257965] [<c0113330>] (dma_cache_maint_page) from [<c0113360>] (__dma_page_cpu_to_dev+0x20/0x90) >> [ 3.267456] [<c0113360>] (__dma_page_cpu_to_dev) from [<c0113444>] (arm_dma_map_page+0x30/0x64) >> [ 3.276550] [<c0113444>] (arm_dma_map_page) from [<c0515110>] (omap2_onenand_read_bufferram+0x150/0x348) >> [ 3.286468] [<c0515110>] (omap2_onenand_read_bufferram) from [<c0511f94>] (onenand_read_oob+0x164/0x668) >> [ 3.296386] [<c0511f94>] (onenand_read_oob) from [<c04f86b0>] (part_read_oob+0x34/0x6c) >> [ 3.304748] [<c04f86b0>] (part_read_oob) from [<c04f6588>] (mtd_read+0xc8/0x108) >> [ 3.312499] [<c04f6588>] (mtd_read) from [<c051ebb8>] (ubi_io_read+0x158/0x250) >> [ 3.320129] [<c051ebb8>] (ubi_io_read) from [<c051643c>] (ubi_read_volume_table+0x1ac/0x8f8) >> [ 3.328948] [<c051643c>] (ubi_read_volume_table) from [<c0524e60>] (ubi_attach+0x134/0x214) >> [ 3.337677] [<c0524e60>] (ubi_attach) from [<c051996c>] (ubi_attach_mtd_dev+0x358/0x794) >> [ 3.346160] [<c051996c>] (ubi_attach_mtd_dev) from [<c093b4f0>] (ubi_init+0x138/0x1d8) >> [ 3.354431] [<c093b4f0>] (ubi_init) from [<c0102818>] (do_one_initcall+0xa8/0x14c) >> [ 3.362335] [<c0102818>] (do_one_initcall) from [<c0900d78>] (kernel_init_freeable+0x110/0x1d4) >> [ 3.371429] [<c0900d78>] (kernel_init_freeable) from [<c06ff358>] (kernel_init+0x8/0x10c) >> [ 3.380004] [<c06ff358>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c) >> [ 3.387908] Exception stack(0xee0affb0 to 0xee0afff8) >> [ 3.393188] ffa0: 00000000 00000000 00000000 00000000 >> [ 3.401733] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 >> [ 3.410278] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 >> [ 3.417205] Code: 1e070f3e e1110003 e1c11003 1e071f3e (ee070f36) >> [ 3.423736] ---[ end trace 3d1a74d3a673ac09 ]--- >> [ 3.428649] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b >> [ 3.428649] >> [ 3.438201] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b >> [ 3.438201] >> -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
* H. Nikolaus Schaller <hns@goldelico.com> [180411 07:05]: > > Am 10.04.2018 um 22:56 schrieb Ladislav Michl <ladis@linux-mips.org>: > > Well, that's a shame... However, this code is in production for several > > months now, > > Well, we could have tested earlier release-candidates... I've found it's way easier to test Linux next on regular basis and report the regressions compared to chasing regressions after the merge window or tagged kernels. By that time you may have already multiple regressions to deal with which is always fun. If you have products running with mainline kernel, maybe set up automated boot testing for core devices to catch regressions early? Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Tony, > Am 12.04.2018 um 17:03 schrieb Tony Lindgren <tony@atomide.com>: > > * H. Nikolaus Schaller <hns@goldelico.com> [180411 07:05]: >>> Am 10.04.2018 um 22:56 schrieb Ladislav Michl <ladis@linux-mips.org>: >>> Well, that's a shame... However, this code is in production for several >>> months now, >> >> Well, we could have tested earlier release-candidates... > > I've found it's way easier to test Linux next on regular basis > and report the regressions compared to chasing regressions after > the merge window or tagged kernels. By that time you may have > already multiple regressions to deal with which is always fun. > > If you have products running with mainline kernel, maybe set up > automated boot testing for core devices to catch regressions > early? Well, it is rare that we face upstream regressions of this severe kind. Every 2-3 years... We much more often have to face missing features in upstream so that we add our own patch sets on top of each -rc. In this case here we could have found this right after the merge window when v4.16-rc1 came out. But by bad chance (and holidays and other more important tasks) we did only test on GTA04 boards with standard NAND. And just now did boot a board with OneNAND installed and were surprised by this boot problem. BR, Nikolaus -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
--- a/drivers/mtd/nand/onenand/omap2.c +++ b/drivers/mtd/nand/onenand/omap2.c @@ -392,6 +392,7 @@ static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, if (buf >= high_memory) { struct page *p1; + goto out_copy; if (((size_t)buf & PAGE_MASK) != ((size_t)(buf + count - 1) & PAGE_MASK)) goto out_copy;