| Message ID | 1524622328-30493-3-git-send-email-andy.yeh@intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Andy, On Wed, Apr 25, 2018 at 11:04 AM Andy Yeh <andy.yeh@intel.com> wrote: > From: Alan Chiang <alanx.chiang@intel.com> > DW9807 is a 10 bit DAC from Dongwoon, designed for linear > control of voice coil motor. > This driver creates a V4L2 subdevice and > provides control to set the desired focus. > Signed-off-by: Andy Yeh <andy.yeh@intel.com> > --- > since v1: > - changed author. > since v2: > - addressed outstanding comments. > - enabled sequential write to update 2 registers in a single transaction. > since v3: > - addressed comments for v3. > - Remove redundant codes and declare some variables as constant variable. > - separate DT binding to another patch > since v4: > - sent patchset included DT binding with cover page > since v6: > - change the return code of i2c_check > - fix long cols exceed 80 chars > - remove #define DW9807_NAME since only used once > since v7: > - Remove some redundant type cast > - Modify to meet the coding style > - Replace a while loop by readx_poll_timeout function > - Return the i2c error directly Reviewed-by: Tomasz Figa <tfiga@chromium.org> Thanks for addressing the comments. Best regards, Tomasz
Hi Andy,
thanks for addressing comments on previous versions
On Wed, Apr 25, 2018 at 10:12:08AM +0800, Andy Yeh wrote:
> From: Alan Chiang <alanx.chiang@intel.com>
>
> DW9807 is a 10 bit DAC from Dongwoon, designed for linear
> control of voice coil motor.
>
> This driver creates a V4L2 subdevice and
> provides control to set the desired focus.
>
> Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Thanks
j
> ---
> since v1:
> - changed author.
> since v2:
> - addressed outstanding comments.
> - enabled sequential write to update 2 registers in a single transaction.
> since v3:
> - addressed comments for v3.
> - Remove redundant codes and declare some variables as constant variable.
> - separate DT binding to another patch
> since v4:
> - sent patchset included DT binding with cover page
> since v6:
> - change the return code of i2c_check
> - fix long cols exceed 80 chars
> - remove #define DW9807_NAME since only used once
> since v7:
> - Remove some redundant type cast
> - Modify to meet the coding style
> - Replace a while loop by readx_poll_timeout function
> - Return the i2c error directly.
>
> MAINTAINERS | 7 +
> drivers/media/i2c/Kconfig | 10 ++
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/dw9807.c | 329 +++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 347 insertions(+)
> create mode 100644 drivers/media/i2c/dw9807.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 845fc25..a339bb5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4385,6 +4385,13 @@ T: git git://linuxtv.org/media_tree.git
> S: Maintained
> F: drivers/media/i2c/dw9714.c
>
> +DONGWOON DW9807 LENS VOICE COIL DRIVER
> +M: Sakari Ailus <sakari.ailus@linux.intel.com>
> +L: linux-media@vger.kernel.org
> +T: git git://linuxtv.org/media_tree.git
> +S: Maintained
> +F: drivers/media/i2c/dw9807.c
> +
> DOUBLETALK DRIVER
> M: "James R. Van Zandt" <jrv@vanzandt.mv.com>
> L: blinux-list@redhat.com
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index cb5d7ff..fd01842 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -325,6 +325,16 @@ config VIDEO_DW9714
> capability. This is designed for linear control of
> voice coil motors, controlled via I2C serial interface.
>
> +config VIDEO_DW9807
> + tristate "DW9807 lens voice coil support"
> + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> + depends on VIDEO_V4L2_SUBDEV_API
> + ---help---
> + This is a driver for the DW9807 camera lens voice coil.
> + DW9807 is a 10 bit DAC with 100mA output current sink
> + capability. This is designed for linear control of
> + voice coil motors, controlled via I2C serial interface.
> +
> config VIDEO_SAA7110
> tristate "Philips SAA7110 video decoder"
> depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index 548a9ef..1b62639 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o
> obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
> obj-$(CONFIG_VIDEO_AD5820) += ad5820.o
> obj-$(CONFIG_VIDEO_DW9714) += dw9714.o
> +obj-$(CONFIG_VIDEO_DW9807) += dw9807.o
> obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o
> obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o
> obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o
> diff --git a/drivers/media/i2c/dw9807.c b/drivers/media/i2c/dw9807.c
> new file mode 100644
> index 0000000..28ede2b
> --- /dev/null
> +++ b/drivers/media/i2c/dw9807.c
> @@ -0,0 +1,329 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (C) 2018 Intel Corporation
> +
> +#include <linux/acpi.h>
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +
> +#define DW9807_MAX_FOCUS_POS 1023
> +/*
> + * This sets the minimum granularity for the focus positions.
> + * A value of 1 gives maximum accuracy for a desired focus position.
> + */
> +#define DW9807_FOCUS_STEPS 1
> +/*
> + * This acts as the minimum granularity of lens movement.
> + * Keep this value power of 2, so the control steps can be
> + * uniformly adjusted for gradual lens movement, with desired
> + * number of control steps.
> + */
> +#define DW9807_CTRL_STEPS 16
> +#define DW9807_CTRL_DELAY_US 1000
> +
> +#define DW9807_CTL_ADDR 0x02
> +/*
> + * DW9807 separates two registers to control the VCM position.
> + * One for MSB value, another is LSB value.
> + */
> +#define DW9807_MSB_ADDR 0x03
> +#define DW9807_LSB_ADDR 0x04
> +#define DW9807_STATUS_ADDR 0x05
> +#define DW9807_MODE_ADDR 0x06
> +#define DW9807_RESONANCE_ADDR 0x07
> +
> +#define MAX_RETRY 10
> +
> +struct dw9807_device {
> + struct v4l2_ctrl_handler ctrls_vcm;
> + struct v4l2_subdev sd;
> + u16 current_val;
> +};
> +
> +static inline struct dw9807_device *sd_to_dw9807_vcm(
> + struct v4l2_subdev *subdev)
> +{
> + return container_of(subdev, struct dw9807_device, sd);
> +}
> +
> +static int dw9807_i2c_check(struct i2c_client *client)
> +{
> + const char status_addr = DW9807_STATUS_ADDR;
> + char status_result;
> + int ret;
> +
> + ret = i2c_master_send(client, &status_addr, sizeof(status_addr));
> + if (ret < 0) {
> + dev_err(&client->dev, "I2C write STATUS address fail ret = %d\n",
> + ret);
> + return ret;
> + }
> +
> + ret = i2c_master_recv(client, &status_result, sizeof(status_result));
> + if (ret < 0) {
> + dev_err(&client->dev, "I2C read STATUS value fail ret = %d\n",
> + ret);
> + return ret;
> + }
> +
> + return status_result;
> +}
> +
> +static int dw9807_set_dac(struct i2c_client *client, u16 data)
> +{
> + const char tx_data[3] = {
> + DW9807_MSB_ADDR, ((data >> 8) & 0x03), (data & 0xff)
> + };
> + int val, ret, retry = 0;
> +
> + /*
> + * According to the datasheet, need to check the bus status before we
> + * write VCM position. This ensure that we really write the value
> + * into the register
> + */
> + ret = readx_poll_timeout(dw9807_i2c_check, client, val, val <= 0,
> + DW9807_CTRL_DELAY_US, MAX_RETRY * DW9807_CTRL_DELAY_US);
> +
> + if (ret || val < 0) {
> + if (ret) {
> + dev_warn(&client->dev,
> + "Cannot do the write operation because VCM is busy\n");
> + }
> +
> + return ret ? -EBUSY : val;
> + }
> +
> + /* Write VCM position to registers */
> + ret = i2c_master_send(client, tx_data, sizeof(tx_data));
> + if (ret < 0) {
> + dev_err(&client->dev,
> + "I2C write MSB fail ret=%d\n", ret);
> +
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct dw9807_device *dev_vcm = container_of(ctrl->handler,
> + struct dw9807_device, ctrls_vcm);
> +
> + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE) {
> + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd);
> +
> + dev_vcm->current_val = ctrl->val;
> + return dw9807_set_dac(client, ctrl->val);
> + }
> +
> + return -EINVAL;
> +}
> +
> +static const struct v4l2_ctrl_ops dw9807_vcm_ctrl_ops = {
> + .s_ctrl = dw9807_set_ctrl,
> +};
> +
> +static int dw9807_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + int rval;
> +
> + rval = pm_runtime_get_sync(sd->dev);
> + if (rval < 0) {
> + pm_runtime_put_noidle(sd->dev);
> + return rval;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + pm_runtime_put(sd->dev);
> +
> + return 0;
> +}
> +
> +static const struct v4l2_subdev_internal_ops dw9807_int_ops = {
> + .open = dw9807_open,
> + .close = dw9807_close,
> +};
> +
> +static const struct v4l2_subdev_ops dw9807_ops = { };
> +
> +static void dw9807_subdev_cleanup(struct dw9807_device *dw9807_dev)
> +{
> + v4l2_async_unregister_subdev(&dw9807_dev->sd);
> + v4l2_ctrl_handler_free(&dw9807_dev->ctrls_vcm);
> + media_entity_cleanup(&dw9807_dev->sd.entity);
> +}
> +
> +static int dw9807_init_controls(struct dw9807_device *dev_vcm)
> +{
> + struct v4l2_ctrl_handler *hdl = &dev_vcm->ctrls_vcm;
> + const struct v4l2_ctrl_ops *ops = &dw9807_vcm_ctrl_ops;
> + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd);
> +
> + v4l2_ctrl_handler_init(hdl, 1);
> +
> + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE,
> + 0, DW9807_MAX_FOCUS_POS, DW9807_FOCUS_STEPS, 0);
> +
> + dev_vcm->sd.ctrl_handler = hdl;
> + if (hdl->error) {
> + dev_err(&client->dev, "%s fail error: 0x%x\n",
> + __func__, hdl->error);
> + return hdl->error;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_probe(struct i2c_client *client)
> +{
> + struct dw9807_device *dw9807_dev;
> + int rval;
> +
> + dw9807_dev = devm_kzalloc(&client->dev, sizeof(*dw9807_dev),
> + GFP_KERNEL);
> + if (dw9807_dev == NULL)
> + return -ENOMEM;
> +
> + v4l2_i2c_subdev_init(&dw9807_dev->sd, client, &dw9807_ops);
> + dw9807_dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + dw9807_dev->sd.internal_ops = &dw9807_int_ops;
> +
> + rval = dw9807_init_controls(dw9807_dev);
> + if (rval)
> + goto err_cleanup;
> +
> + rval = media_entity_pads_init(&dw9807_dev->sd.entity, 0, NULL);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + dw9807_dev->sd.entity.function = MEDIA_ENT_F_LENS;
> +
> + rval = v4l2_async_register_subdev(&dw9807_dev->sd);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + pm_runtime_set_active(&client->dev);
> + pm_runtime_enable(&client->dev);
> + pm_runtime_idle(&client->dev);
> +
> + return 0;
> +
> +err_cleanup:
> + dw9807_subdev_cleanup(dw9807_dev);
> +
> + return rval;
> +}
> +
> +static int dw9807_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> +
> + pm_runtime_disable(&client->dev);
> + pm_runtime_set_suspended(&client->dev);
> +
> + dw9807_subdev_cleanup(dw9807_dev);
> +
> + return 0;
> +}
> +
> +/*
> + * This function sets the vcm position, so it consumes least current
> + * The lens position is gradually moved in units of DW9807_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9807_vcm_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> + const char tx_data[2] = { DW9807_CTL_ADDR, 0x01 };
> + int ret, val;
> +
> + for (val = dw9807_dev->current_val & ~(DW9807_CTRL_STEPS - 1);
> + val >= 0; val -= DW9807_CTRL_STEPS) {
> + ret = dw9807_set_dac(client, val);
> + if (ret)
> + dev_err_once(dev, "%s I2C failure: %d", __func__, ret);
> + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10);
> + }
> +
> + /* Power down */
> + ret = i2c_master_send(client, tx_data, sizeof(tx_data));
> + if (ret < 0) {
> + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * This function sets the vcm position to the value set by the user
> + * through v4l2_ctrl_ops s_ctrl handler
> + * The lens position is gradually moved in units of DW9807_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9807_vcm_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> + const char tx_data[2] = { DW9807_CTL_ADDR, 0x00 };
> + int ret, val;
> +
> + /* Power on */
> + ret = i2c_master_send(client, tx_data, sizeof(tx_data));
> + if (ret < 0) {
> + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret);
> + return ret;
> + }
> +
> + for (val = dw9807_dev->current_val % DW9807_CTRL_STEPS;
> + val < dw9807_dev->current_val + DW9807_CTRL_STEPS - 1;
> + val += DW9807_CTRL_STEPS) {
> + ret = dw9807_set_dac(client, val);
> + if (ret)
> + dev_err_ratelimited(dev, "%s I2C failure: %d",
> + __func__, ret);
> + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id dw9807_of_table[] = {
> + { .compatible = "dongwoon,dw9807" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, dw9807_of_table);
> +
> +static const struct dev_pm_ops dw9807_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume)
> + SET_RUNTIME_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume, NULL)
> +};
> +
> +static struct i2c_driver dw9807_i2c_driver = {
> + .driver = {
> + .name = "dw9807",
> + .pm = &dw9807_pm_ops,
> + .of_match_table = dw9807_of_table,
> + },
> + .probe_new = dw9807_probe,
> + .remove = dw9807_remove,
> +};
> +
> +module_i2c_driver(dw9807_i2c_driver);
> +
> +MODULE_AUTHOR("Chiang, Alan <alanx.chiang@intel.com>");
> +MODULE_DESCRIPTION("DW9807 VCM driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
Thanks for your kindly review. Submitted v9 only with Reviewed/Acked-by. Regards, Andy -----Original Message----- From: jacopo mondi [mailto:jacopo@jmondi.org] Sent: Wednesday, May 2, 2018 3:17 PM To: Yeh, Andy <andy.yeh@intel.com> Cc: linux-media@vger.kernel.org; sakari.ailus@linux.intel.com; devicetree@vger.kernel.org; tfiga@chromium.org; Chiang, AlanX <alanx.chiang@intel.com> Subject: Re: [RESEND PATCH v8 2/2] media: dw9807: Add dw9807 vcm driver Hi Andy, thanks for addressing comments on previous versions On Wed, Apr 25, 2018 at 10:12:08AM +0800, Andy Yeh wrote: > From: Alan Chiang <alanx.chiang@intel.com> > > DW9807 is a 10 bit DAC from Dongwoon, designed for linear control of > voice coil motor. > > This driver creates a V4L2 subdevice and provides control to set the > desired focus. > > Signed-off-by: Andy Yeh <andy.yeh@intel.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Thanks j > --- > since v1: > - changed author. > since v2: > - addressed outstanding comments. > - enabled sequential write to update 2 registers in a single transaction. > since v3: > - addressed comments for v3. > - Remove redundant codes and declare some variables as constant variable. > - separate DT binding to another patch since v4: > - sent patchset included DT binding with cover page since v6: > - change the return code of i2c_check > - fix long cols exceed 80 chars > - remove #define DW9807_NAME since only used once since v7: > - Remove some redundant type cast > - Modify to meet the coding style > - Replace a while loop by readx_poll_timeout function > - Return the i2c error directly. > > MAINTAINERS | 7 + > drivers/media/i2c/Kconfig | 10 ++ > drivers/media/i2c/Makefile | 1 + > drivers/media/i2c/dw9807.c | 329 > +++++++++++++++++++++++++++++++++++++++++++++ > 4 files changed, 347 insertions(+) > create mode 100644 drivers/media/i2c/dw9807.c > > diff --git a/MAINTAINERS b/MAINTAINERS index 845fc25..a339bb5 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -4385,6 +4385,13 @@ T: git git://linuxtv.org/media_tree.git > S: Maintained > F: drivers/media/i2c/dw9714.c > > +DONGWOON DW9807 LENS VOICE COIL DRIVER > +M: Sakari Ailus <sakari.ailus@linux.intel.com> > +L: linux-media@vger.kernel.org > +T: git git://linuxtv.org/media_tree.git > +S: Maintained > +F: drivers/media/i2c/dw9807.c > + > DOUBLETALK DRIVER > M: "James R. Van Zandt" <jrv@vanzandt.mv.com> > L: blinux-list@redhat.com > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index cb5d7ff..fd01842 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -325,6 +325,16 @@ config VIDEO_DW9714 > capability. This is designed for linear control of > voice coil motors, controlled via I2C serial interface. > > +config VIDEO_DW9807 > + tristate "DW9807 lens voice coil support" > + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER > + depends on VIDEO_V4L2_SUBDEV_API > + ---help--- > + This is a driver for the DW9807 camera lens voice coil. > + DW9807 is a 10 bit DAC with 100mA output current sink > + capability. This is designed for linear control of > + voice coil motors, controlled via I2C serial interface. > + > config VIDEO_SAA7110 > tristate "Philips SAA7110 video decoder" > depends on VIDEO_V4L2 && I2C > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index 548a9ef..1b62639 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -23,6 +23,7 @@ obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o > obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o > obj-$(CONFIG_VIDEO_AD5820) += ad5820.o > obj-$(CONFIG_VIDEO_DW9714) += dw9714.o > +obj-$(CONFIG_VIDEO_DW9807) += dw9807.o > obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o > obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o > obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o diff --git > a/drivers/media/i2c/dw9807.c b/drivers/media/i2c/dw9807.c new file > mode 100644 index 0000000..28ede2b > --- /dev/null > +++ b/drivers/media/i2c/dw9807.c > @@ -0,0 +1,329 @@ > +// SPDX-License-Identifier: GPL-2.0 > +// Copyright (C) 2018 Intel Corporation > + > +#include <linux/acpi.h> > +#include <linux/delay.h> > +#include <linux/i2c.h> > +#include <linux/iopoll.h> > +#include <linux/module.h> > +#include <linux/pm_runtime.h> > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > + > +#define DW9807_MAX_FOCUS_POS 1023 > +/* > + * This sets the minimum granularity for the focus positions. > + * A value of 1 gives maximum accuracy for a desired focus position. > + */ > +#define DW9807_FOCUS_STEPS 1 > +/* > + * This acts as the minimum granularity of lens movement. > + * Keep this value power of 2, so the control steps can be > + * uniformly adjusted for gradual lens movement, with desired > + * number of control steps. > + */ > +#define DW9807_CTRL_STEPS 16 > +#define DW9807_CTRL_DELAY_US 1000 > + > +#define DW9807_CTL_ADDR 0x02 > +/* > + * DW9807 separates two registers to control the VCM position. > + * One for MSB value, another is LSB value. > + */ > +#define DW9807_MSB_ADDR 0x03 > +#define DW9807_LSB_ADDR 0x04 > +#define DW9807_STATUS_ADDR 0x05 > +#define DW9807_MODE_ADDR 0x06 > +#define DW9807_RESONANCE_ADDR 0x07 > + > +#define MAX_RETRY 10 > + > +struct dw9807_device { > + struct v4l2_ctrl_handler ctrls_vcm; > + struct v4l2_subdev sd; > + u16 current_val; > +}; > + > +static inline struct dw9807_device *sd_to_dw9807_vcm( > + struct v4l2_subdev *subdev) > +{ > + return container_of(subdev, struct dw9807_device, sd); } > + > +static int dw9807_i2c_check(struct i2c_client *client) { > + const char status_addr = DW9807_STATUS_ADDR; > + char status_result; > + int ret; > + > + ret = i2c_master_send(client, &status_addr, sizeof(status_addr)); > + if (ret < 0) { > + dev_err(&client->dev, "I2C write STATUS address fail ret = %d\n", > + ret); > + return ret; > + } > + > + ret = i2c_master_recv(client, &status_result, sizeof(status_result)); > + if (ret < 0) { > + dev_err(&client->dev, "I2C read STATUS value fail ret = %d\n", > + ret); > + return ret; > + } > + > + return status_result; > +} > + > +static int dw9807_set_dac(struct i2c_client *client, u16 data) { > + const char tx_data[3] = { > + DW9807_MSB_ADDR, ((data >> 8) & 0x03), (data & 0xff) > + }; > + int val, ret, retry = 0; > + > + /* > + * According to the datasheet, need to check the bus status before we > + * write VCM position. This ensure that we really write the value > + * into the register > + */ > + ret = readx_poll_timeout(dw9807_i2c_check, client, val, val <= 0, > + DW9807_CTRL_DELAY_US, MAX_RETRY * DW9807_CTRL_DELAY_US); > + > + if (ret || val < 0) { > + if (ret) { > + dev_warn(&client->dev, > + "Cannot do the write operation because VCM is busy\n"); > + } > + > + return ret ? -EBUSY : val; > + } > + > + /* Write VCM position to registers */ > + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); > + if (ret < 0) { > + dev_err(&client->dev, > + "I2C write MSB fail ret=%d\n", ret); > + > + return ret; > + } > + > + return 0; > +} > + > +static int dw9807_set_ctrl(struct v4l2_ctrl *ctrl) { > + struct dw9807_device *dev_vcm = container_of(ctrl->handler, > + struct dw9807_device, ctrls_vcm); > + > + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE) { > + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd); > + > + dev_vcm->current_val = ctrl->val; > + return dw9807_set_dac(client, ctrl->val); > + } > + > + return -EINVAL; > +} > + > +static const struct v4l2_ctrl_ops dw9807_vcm_ctrl_ops = { > + .s_ctrl = dw9807_set_ctrl, > +}; > + > +static int dw9807_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh > +*fh) { > + int rval; > + > + rval = pm_runtime_get_sync(sd->dev); > + if (rval < 0) { > + pm_runtime_put_noidle(sd->dev); > + return rval; > + } > + > + return 0; > +} > + > +static int dw9807_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh > +*fh) { > + pm_runtime_put(sd->dev); > + > + return 0; > +} > + > +static const struct v4l2_subdev_internal_ops dw9807_int_ops = { > + .open = dw9807_open, > + .close = dw9807_close, > +}; > + > +static const struct v4l2_subdev_ops dw9807_ops = { }; > + > +static void dw9807_subdev_cleanup(struct dw9807_device *dw9807_dev) { > + v4l2_async_unregister_subdev(&dw9807_dev->sd); > + v4l2_ctrl_handler_free(&dw9807_dev->ctrls_vcm); > + media_entity_cleanup(&dw9807_dev->sd.entity); > +} > + > +static int dw9807_init_controls(struct dw9807_device *dev_vcm) { > + struct v4l2_ctrl_handler *hdl = &dev_vcm->ctrls_vcm; > + const struct v4l2_ctrl_ops *ops = &dw9807_vcm_ctrl_ops; > + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd); > + > + v4l2_ctrl_handler_init(hdl, 1); > + > + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE, > + 0, DW9807_MAX_FOCUS_POS, DW9807_FOCUS_STEPS, 0); > + > + dev_vcm->sd.ctrl_handler = hdl; > + if (hdl->error) { > + dev_err(&client->dev, "%s fail error: 0x%x\n", > + __func__, hdl->error); > + return hdl->error; > + } > + > + return 0; > +} > + > +static int dw9807_probe(struct i2c_client *client) { > + struct dw9807_device *dw9807_dev; > + int rval; > + > + dw9807_dev = devm_kzalloc(&client->dev, sizeof(*dw9807_dev), > + GFP_KERNEL); > + if (dw9807_dev == NULL) > + return -ENOMEM; > + > + v4l2_i2c_subdev_init(&dw9807_dev->sd, client, &dw9807_ops); > + dw9807_dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + dw9807_dev->sd.internal_ops = &dw9807_int_ops; > + > + rval = dw9807_init_controls(dw9807_dev); > + if (rval) > + goto err_cleanup; > + > + rval = media_entity_pads_init(&dw9807_dev->sd.entity, 0, NULL); > + if (rval < 0) > + goto err_cleanup; > + > + dw9807_dev->sd.entity.function = MEDIA_ENT_F_LENS; > + > + rval = v4l2_async_register_subdev(&dw9807_dev->sd); > + if (rval < 0) > + goto err_cleanup; > + > + pm_runtime_set_active(&client->dev); > + pm_runtime_enable(&client->dev); > + pm_runtime_idle(&client->dev); > + > + return 0; > + > +err_cleanup: > + dw9807_subdev_cleanup(dw9807_dev); > + > + return rval; > +} > + > +static int dw9807_remove(struct i2c_client *client) { > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); > + > + pm_runtime_disable(&client->dev); > + pm_runtime_set_suspended(&client->dev); > + > + dw9807_subdev_cleanup(dw9807_dev); > + > + return 0; > +} > + > +/* > + * This function sets the vcm position, so it consumes least current > + * The lens position is gradually moved in units of > +DW9807_CTRL_STEPS, > + * to make the movements smoothly. > + */ > +static int __maybe_unused dw9807_vcm_suspend(struct device *dev) { > + struct i2c_client *client = to_i2c_client(dev); > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); > + const char tx_data[2] = { DW9807_CTL_ADDR, 0x01 }; > + int ret, val; > + > + for (val = dw9807_dev->current_val & ~(DW9807_CTRL_STEPS - 1); > + val >= 0; val -= DW9807_CTRL_STEPS) { > + ret = dw9807_set_dac(client, val); > + if (ret) > + dev_err_once(dev, "%s I2C failure: %d", __func__, ret); > + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10); > + } > + > + /* Power down */ > + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); > + if (ret < 0) { > + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret); > + return ret; > + } > + > + return 0; > +} > + > +/* > + * This function sets the vcm position to the value set by the user > + * through v4l2_ctrl_ops s_ctrl handler > + * The lens position is gradually moved in units of > +DW9807_CTRL_STEPS, > + * to make the movements smoothly. > + */ > +static int __maybe_unused dw9807_vcm_resume(struct device *dev) { > + struct i2c_client *client = to_i2c_client(dev); > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); > + const char tx_data[2] = { DW9807_CTL_ADDR, 0x00 }; > + int ret, val; > + > + /* Power on */ > + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); > + if (ret < 0) { > + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret); > + return ret; > + } > + > + for (val = dw9807_dev->current_val % DW9807_CTRL_STEPS; > + val < dw9807_dev->current_val + DW9807_CTRL_STEPS - 1; > + val += DW9807_CTRL_STEPS) { > + ret = dw9807_set_dac(client, val); > + if (ret) > + dev_err_ratelimited(dev, "%s I2C failure: %d", > + __func__, ret); > + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10); > + } > + > + return 0; > +} > + > +static const struct of_device_id dw9807_of_table[] = { > + { .compatible = "dongwoon,dw9807" }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, dw9807_of_table); > + > +static const struct dev_pm_ops dw9807_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume) > + SET_RUNTIME_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume, NULL) }; > + > +static struct i2c_driver dw9807_i2c_driver = { > + .driver = { > + .name = "dw9807", > + .pm = &dw9807_pm_ops, > + .of_match_table = dw9807_of_table, > + }, > + .probe_new = dw9807_probe, > + .remove = dw9807_remove, > +}; > + > +module_i2c_driver(dw9807_i2c_driver); > + > +MODULE_AUTHOR("Chiang, Alan <alanx.chiang@intel.com>"); > +MODULE_DESCRIPTION("DW9807 VCM driver"); MODULE_LICENSE("GPL v2"); > -- > 2.7.4 >
diff --git a/MAINTAINERS b/MAINTAINERS index 845fc25..a339bb5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4385,6 +4385,13 @@ T: git git://linuxtv.org/media_tree.git S: Maintained F: drivers/media/i2c/dw9714.c +DONGWOON DW9807 LENS VOICE COIL DRIVER +M: Sakari Ailus <sakari.ailus@linux.intel.com> +L: linux-media@vger.kernel.org +T: git git://linuxtv.org/media_tree.git +S: Maintained +F: drivers/media/i2c/dw9807.c + DOUBLETALK DRIVER M: "James R. Van Zandt" <jrv@vanzandt.mv.com> L: blinux-list@redhat.com diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index cb5d7ff..fd01842 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -325,6 +325,16 @@ config VIDEO_DW9714 capability. This is designed for linear control of voice coil motors, controlled via I2C serial interface. +config VIDEO_DW9807 + tristate "DW9807 lens voice coil support" + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER + depends on VIDEO_V4L2_SUBDEV_API + ---help--- + This is a driver for the DW9807 camera lens voice coil. + DW9807 is a 10 bit DAC with 100mA output current sink + capability. This is designed for linear control of + voice coil motors, controlled via I2C serial interface. + config VIDEO_SAA7110 tristate "Philips SAA7110 video decoder" depends on VIDEO_V4L2 && I2C diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index 548a9ef..1b62639 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -23,6 +23,7 @@ obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o obj-$(CONFIG_VIDEO_AD5820) += ad5820.o obj-$(CONFIG_VIDEO_DW9714) += dw9714.o +obj-$(CONFIG_VIDEO_DW9807) += dw9807.o obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o diff --git a/drivers/media/i2c/dw9807.c b/drivers/media/i2c/dw9807.c new file mode 100644 index 0000000..28ede2b --- /dev/null +++ b/drivers/media/i2c/dw9807.c @@ -0,0 +1,329 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (C) 2018 Intel Corporation + +#include <linux/acpi.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> + +#define DW9807_MAX_FOCUS_POS 1023 +/* + * This sets the minimum granularity for the focus positions. + * A value of 1 gives maximum accuracy for a desired focus position. + */ +#define DW9807_FOCUS_STEPS 1 +/* + * This acts as the minimum granularity of lens movement. + * Keep this value power of 2, so the control steps can be + * uniformly adjusted for gradual lens movement, with desired + * number of control steps. + */ +#define DW9807_CTRL_STEPS 16 +#define DW9807_CTRL_DELAY_US 1000 + +#define DW9807_CTL_ADDR 0x02 +/* + * DW9807 separates two registers to control the VCM position. + * One for MSB value, another is LSB value. + */ +#define DW9807_MSB_ADDR 0x03 +#define DW9807_LSB_ADDR 0x04 +#define DW9807_STATUS_ADDR 0x05 +#define DW9807_MODE_ADDR 0x06 +#define DW9807_RESONANCE_ADDR 0x07 + +#define MAX_RETRY 10 + +struct dw9807_device { + struct v4l2_ctrl_handler ctrls_vcm; + struct v4l2_subdev sd; + u16 current_val; +}; + +static inline struct dw9807_device *sd_to_dw9807_vcm( + struct v4l2_subdev *subdev) +{ + return container_of(subdev, struct dw9807_device, sd); +} + +static int dw9807_i2c_check(struct i2c_client *client) +{ + const char status_addr = DW9807_STATUS_ADDR; + char status_result; + int ret; + + ret = i2c_master_send(client, &status_addr, sizeof(status_addr)); + if (ret < 0) { + dev_err(&client->dev, "I2C write STATUS address fail ret = %d\n", + ret); + return ret; + } + + ret = i2c_master_recv(client, &status_result, sizeof(status_result)); + if (ret < 0) { + dev_err(&client->dev, "I2C read STATUS value fail ret = %d\n", + ret); + return ret; + } + + return status_result; +} + +static int dw9807_set_dac(struct i2c_client *client, u16 data) +{ + const char tx_data[3] = { + DW9807_MSB_ADDR, ((data >> 8) & 0x03), (data & 0xff) + }; + int val, ret, retry = 0; + + /* + * According to the datasheet, need to check the bus status before we + * write VCM position. This ensure that we really write the value + * into the register + */ + ret = readx_poll_timeout(dw9807_i2c_check, client, val, val <= 0, + DW9807_CTRL_DELAY_US, MAX_RETRY * DW9807_CTRL_DELAY_US); + + if (ret || val < 0) { + if (ret) { + dev_warn(&client->dev, + "Cannot do the write operation because VCM is busy\n"); + } + + return ret ? -EBUSY : val; + } + + /* Write VCM position to registers */ + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); + if (ret < 0) { + dev_err(&client->dev, + "I2C write MSB fail ret=%d\n", ret); + + return ret; + } + + return 0; +} + +static int dw9807_set_ctrl(struct v4l2_ctrl *ctrl) +{ + struct dw9807_device *dev_vcm = container_of(ctrl->handler, + struct dw9807_device, ctrls_vcm); + + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE) { + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd); + + dev_vcm->current_val = ctrl->val; + return dw9807_set_dac(client, ctrl->val); + } + + return -EINVAL; +} + +static const struct v4l2_ctrl_ops dw9807_vcm_ctrl_ops = { + .s_ctrl = dw9807_set_ctrl, +}; + +static int dw9807_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) +{ + int rval; + + rval = pm_runtime_get_sync(sd->dev); + if (rval < 0) { + pm_runtime_put_noidle(sd->dev); + return rval; + } + + return 0; +} + +static int dw9807_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) +{ + pm_runtime_put(sd->dev); + + return 0; +} + +static const struct v4l2_subdev_internal_ops dw9807_int_ops = { + .open = dw9807_open, + .close = dw9807_close, +}; + +static const struct v4l2_subdev_ops dw9807_ops = { }; + +static void dw9807_subdev_cleanup(struct dw9807_device *dw9807_dev) +{ + v4l2_async_unregister_subdev(&dw9807_dev->sd); + v4l2_ctrl_handler_free(&dw9807_dev->ctrls_vcm); + media_entity_cleanup(&dw9807_dev->sd.entity); +} + +static int dw9807_init_controls(struct dw9807_device *dev_vcm) +{ + struct v4l2_ctrl_handler *hdl = &dev_vcm->ctrls_vcm; + const struct v4l2_ctrl_ops *ops = &dw9807_vcm_ctrl_ops; + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd); + + v4l2_ctrl_handler_init(hdl, 1); + + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE, + 0, DW9807_MAX_FOCUS_POS, DW9807_FOCUS_STEPS, 0); + + dev_vcm->sd.ctrl_handler = hdl; + if (hdl->error) { + dev_err(&client->dev, "%s fail error: 0x%x\n", + __func__, hdl->error); + return hdl->error; + } + + return 0; +} + +static int dw9807_probe(struct i2c_client *client) +{ + struct dw9807_device *dw9807_dev; + int rval; + + dw9807_dev = devm_kzalloc(&client->dev, sizeof(*dw9807_dev), + GFP_KERNEL); + if (dw9807_dev == NULL) + return -ENOMEM; + + v4l2_i2c_subdev_init(&dw9807_dev->sd, client, &dw9807_ops); + dw9807_dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + dw9807_dev->sd.internal_ops = &dw9807_int_ops; + + rval = dw9807_init_controls(dw9807_dev); + if (rval) + goto err_cleanup; + + rval = media_entity_pads_init(&dw9807_dev->sd.entity, 0, NULL); + if (rval < 0) + goto err_cleanup; + + dw9807_dev->sd.entity.function = MEDIA_ENT_F_LENS; + + rval = v4l2_async_register_subdev(&dw9807_dev->sd); + if (rval < 0) + goto err_cleanup; + + pm_runtime_set_active(&client->dev); + pm_runtime_enable(&client->dev); + pm_runtime_idle(&client->dev); + + return 0; + +err_cleanup: + dw9807_subdev_cleanup(dw9807_dev); + + return rval; +} + +static int dw9807_remove(struct i2c_client *client) +{ + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); + + pm_runtime_disable(&client->dev); + pm_runtime_set_suspended(&client->dev); + + dw9807_subdev_cleanup(dw9807_dev); + + return 0; +} + +/* + * This function sets the vcm position, so it consumes least current + * The lens position is gradually moved in units of DW9807_CTRL_STEPS, + * to make the movements smoothly. + */ +static int __maybe_unused dw9807_vcm_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); + const char tx_data[2] = { DW9807_CTL_ADDR, 0x01 }; + int ret, val; + + for (val = dw9807_dev->current_val & ~(DW9807_CTRL_STEPS - 1); + val >= 0; val -= DW9807_CTRL_STEPS) { + ret = dw9807_set_dac(client, val); + if (ret) + dev_err_once(dev, "%s I2C failure: %d", __func__, ret); + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10); + } + + /* Power down */ + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); + if (ret < 0) { + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret); + return ret; + } + + return 0; +} + +/* + * This function sets the vcm position to the value set by the user + * through v4l2_ctrl_ops s_ctrl handler + * The lens position is gradually moved in units of DW9807_CTRL_STEPS, + * to make the movements smoothly. + */ +static int __maybe_unused dw9807_vcm_resume(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd); + const char tx_data[2] = { DW9807_CTL_ADDR, 0x00 }; + int ret, val; + + /* Power on */ + ret = i2c_master_send(client, tx_data, sizeof(tx_data)); + if (ret < 0) { + dev_err(&client->dev, "I2C write CTL fail ret = %d\n", ret); + return ret; + } + + for (val = dw9807_dev->current_val % DW9807_CTRL_STEPS; + val < dw9807_dev->current_val + DW9807_CTRL_STEPS - 1; + val += DW9807_CTRL_STEPS) { + ret = dw9807_set_dac(client, val); + if (ret) + dev_err_ratelimited(dev, "%s I2C failure: %d", + __func__, ret); + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10); + } + + return 0; +} + +static const struct of_device_id dw9807_of_table[] = { + { .compatible = "dongwoon,dw9807" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, dw9807_of_table); + +static const struct dev_pm_ops dw9807_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume) + SET_RUNTIME_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume, NULL) +}; + +static struct i2c_driver dw9807_i2c_driver = { + .driver = { + .name = "dw9807", + .pm = &dw9807_pm_ops, + .of_match_table = dw9807_of_table, + }, + .probe_new = dw9807_probe, + .remove = dw9807_remove, +}; + +module_i2c_driver(dw9807_i2c_driver); + +MODULE_AUTHOR("Chiang, Alan <alanx.chiang@intel.com>"); +MODULE_DESCRIPTION("DW9807 VCM driver"); +MODULE_LICENSE("GPL v2");