diff mbox

[v6,2/5] Documentation: dt-bindings: phy: add phy_config for Rockchip USB Type-C PHY

Message ID 1526895424-22894-2-git-send-email-hl@rock-chips.com (mailing list archive)
State New, archived
Headers show

Commit Message

huang lin May 21, 2018, 9:37 a.m. UTC 
If want to do training outside DP Firmware, need phy voltage swing
and pre_emphasis value.

Signed-off-by: Lin Huang <hl@rock-chips.com>
---
Changes in v2:
- None 
Changes in v3:
- modify property description and add this property to Example
Changes in v4:
- None
Changes in v5:
- None
Changes in v6:
- change rockchip,phy_config to rockchip,phy-config and descript it in detail.
 
 .../devicetree/bindings/phy/phy-rockchip-typec.txt | 36 +++++++++++++++++++++-
 1 file changed, 35 insertions(+), 1 deletion(-)

Comments

Rob Herring (Arm) May 22, 2018, 3:58 p.m. UTC | #1 
On Mon, May 21, 2018 at 05:37:01PM +0800, Lin Huang wrote:
> If want to do training outside DP Firmware, need phy voltage swing
> and pre_emphasis value.
> 
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> ---
> Changes in v2:
> - None 
> Changes in v3:
> - modify property description and add this property to Example
> Changes in v4:
> - None
> Changes in v5:
> - None
> Changes in v6:
> - change rockchip,phy_config to rockchip,phy-config and descript it in detail.
>  
>  .../devicetree/bindings/phy/phy-rockchip-typec.txt | 36 +++++++++++++++++++++-
>  1 file changed, 35 insertions(+), 1 deletion(-)

Reviewed-by: Rob Herring <robh@kernel.org>
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
index 960da7f..40d5e7a 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
@@ -17,7 +17,11 @@  Required properties:
 
 Optional properties:
  - extcon : extcon specifier for the Power Delivery
-
+ - rockchip,phy-config : A list of voltage swing(mV) and pre-emphasis
+			(dB) pairs. They are 3 blocks of 4 entries and
+			correspond to s0p0 ~ s0p3, s1p0 ~ s1p3,
+			s2p0 ~ s2p3, s3p0 ~ s2p3 swing and pre-emphasis
+			values.
 Required nodes : a sub-node is required for each port the phy provides.
 		 The sub-node name is used to identify dp or usb3 port,
 		 and shall be the following entries:
@@ -50,6 +54,21 @@  Example:
 			 <&cru SRST_P_UPHY0_TCPHY>;
 		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
 
+		rockchip,phy-config = <0x2a 0x00>,
+			<0x1f 0x15>,
+			<0x14 0x22>,
+			<0x02 0x2b>,
+
+			<0x21 0x00>,
+			<0x12 0x15>,
+			<0x02 0x22>,
+			<0 0>,
+
+			<0x15 0x00>,
+			<0x00 0x15>,
+			<0 0>,
+			<0 0>;
+
 		tcphy0_dp: dp-port {
 			#phy-cells = <0>;
 		};
@@ -74,6 +93,21 @@  Example:
 			 <&cru SRST_P_UPHY1_TCPHY>;
 		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
 
+		rockchip,phy-config = <0x2a 0x00>,
+			<0x1f 0x15>,
+			<0x14 0x22>,
+			<0x02 0x2b>,
+
+			<0x21 0x00>,
+			<0x12 0x15>,
+			<0x02 0x22>,
+			<0 0>,
+
+			<0x15 0x00>,
+			<0x00 0x15>,
+			<0 0>,
+			<0 0>;
+
 		tcphy1_dp: dp-port {
 			#phy-cells = <0>;
 		};