@@ -15,6 +15,33 @@ Optional properties:
- type: size of the connector, should be specified in case of USB-A, USB-B
non-fullsize connectors: "mini", "micro".
+Optional properties for usb-c-connector:
+- power-role: should be one of "source", "sink" or "dual"(DRP) if typec
+ connector has power support.
+- try-power-role: preferred power role if "dual"(DRP) can support Try.SNK
+ or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC.
+- data-role: should be one of "host", "device", "dual"(DRD) if typec
+ connector supports USB data.
+
+Required properties for usb-c-connector with power delivery support:
+- source-pdos: An array of u32 with each entry providing supported power
+ source data object(PDO), the detailed bit definitions of PDO can be found
+ in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2
+ Source_Capabilities Message, the order of each entry(PDO) should follow
+ the PD spec chapter 6.4.1. Required for power source and power dual role.
+ User can specify the source PDO array via PDO_FIXED/BATT/VAR() defined in
+ dt-bindings/usb/pd.h.
+- sink-pdos: An array of u32 with each entry providing supported power
+ sink data object(PDO), the detailed bit definitions of PDO can be found
+ in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3
+ Sink Capabilities Message, the order of each entry(PDO) should follow
+ the PD spec chapter 6.4.1. Required for power sink and power dual role.
+ User can specify the sink PDO array via PDO_FIXED/BATT/VAR() defined in
+ dt-bindings/usb/pd.h.
+- op-sink-microwatt: Sink required operating power in microwatt, if source
+ can't offer the power, Capability Mismatch is set. Required for power
+ sink and power dual role.
+
Required nodes:
- any data bus to the connector should be modeled using the OF graph bindings
specified in bindings/graph.txt, unless the bus is between parent node and
@@ -73,3 +100,20 @@ ccic: s2mm005@33 {
};
};
};
+
+3. USB-C connector attached to a typec port controller(ptn5110), which has
+power delivery support and enables drp.
+
+typec: ptn5110@50 {
+ ...
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 12000, 2000)>;
+ op-sink-microwatt = <10000000>;
+ };
+};
new file mode 100644
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_POWER_DELIVERY_H
+#define __DT_POWER_DELIVERY_H
+
+/* Power delivery Power Data Object definitions */
+#define PDO_TYPE_FIXED 0
+#define PDO_TYPE_BATT 1
+#define PDO_TYPE_VAR 2
+#define PDO_TYPE_APDO 3
+
+#define PDO_TYPE_SHIFT 30
+#define PDO_TYPE_MASK 0x3
+
+#define PDO_TYPE(t) ((t) << PDO_TYPE_SHIFT)
+
+#define PDO_VOLT_MASK 0x3ff
+#define PDO_CURR_MASK 0x3ff
+#define PDO_PWR_MASK 0x3ff
+
+#define PDO_FIXED_DUAL_ROLE (1 << 29) /* Power role swap supported */
+#define PDO_FIXED_SUSPEND (1 << 28) /* USB Suspend supported (Source) */
+#define PDO_FIXED_HIGHER_CAP (1 << 28) /* Requires more than vSafe5V (Sink) */
+#define PDO_FIXED_EXTPOWER (1 << 27) /* Externally powered */
+#define PDO_FIXED_USB_COMM (1 << 26) /* USB communications capable */
+#define PDO_FIXED_DATA_SWAP (1 << 25) /* Data role swap supported */
+#define PDO_FIXED_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_FIXED_CURR_SHIFT 0 /* 10mA units */
+
+#define PDO_FIXED_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_FIXED_VOLT_SHIFT)
+#define PDO_FIXED_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) << PDO_FIXED_CURR_SHIFT)
+
+#define PDO_FIXED(mv, ma, flags) \
+ (PDO_TYPE(PDO_TYPE_FIXED) | (flags) | \
+ PDO_FIXED_VOLT(mv) | PDO_FIXED_CURR(ma))
+
+#define VSAFE5V 5000 /* mv units */
+
+#define PDO_BATT_MAX_VOLT_SHIFT 20 /* 50mV units */
+#define PDO_BATT_MIN_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_BATT_MAX_PWR_SHIFT 0 /* 250mW units */
+
+#define PDO_BATT_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_BATT_MIN_VOLT_SHIFT)
+#define PDO_BATT_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_BATT_MAX_VOLT_SHIFT)
+#define PDO_BATT_MAX_POWER(mw) ((((mw) / 250) & PDO_PWR_MASK) << PDO_BATT_MAX_PWR_SHIFT)
+
+#define PDO_BATT(min_mv, max_mv, max_mw) \
+ (PDO_TYPE(PDO_TYPE_BATT) | PDO_BATT_MIN_VOLT(min_mv) | \
+ PDO_BATT_MAX_VOLT(max_mv) | PDO_BATT_MAX_POWER(max_mw))
+
+#define PDO_VAR_MAX_VOLT_SHIFT 20 /* 50mV units */
+#define PDO_VAR_MIN_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_VAR_MAX_CURR_SHIFT 0 /* 10mA units */
+
+#define PDO_VAR_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_VAR_MIN_VOLT_SHIFT)
+#define PDO_VAR_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_VAR_MAX_VOLT_SHIFT)
+#define PDO_VAR_MAX_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) << PDO_VAR_MAX_CURR_SHIFT)
+
+#define PDO_VAR(min_mv, max_mv, max_ma) \
+ (PDO_TYPE(PDO_TYPE_VAR) | PDO_VAR_MIN_VOLT(min_mv) | \
+ PDO_VAR_MAX_VOLT(max_mv) | PDO_VAR_MAX_CURR(max_ma))
+
+ #endif /* __DT_POWER_DELIVERY_H */
Add bindings supported by current typec driver, so user can pass all those properties via dt. Signed-off-by: Li Jun <jun.li@nxp.com> --- .../bindings/connector/usb-connector.txt | 44 +++++++++++++++ include/dt-bindings/usb/pd.h | 62 ++++++++++++++++++++++ 2 files changed, 106 insertions(+)