| Message ID | 20180627095735.24517-4-spanda@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 27.06.2018 11:57, Sandeep Panda wrote: > Document the bindings used for the sn65dsi86 DSI to eDP bridge. > > Changes in v1: > - Rephrase the dt-binding descriptions to be more inline with existing > bindings (Andrzej Hajda). > - Add missing dt-binding that are parsed by corresponding driver > (Andrzej Hajda). > > Changes in v2: > - Remove edp panel specific dt-binding entries. Only keep bridge > specific entries (Sean Paul). > - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). > - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). > > Changes in v3: > - Remove irq-gpio dt entry and instead populate is an interrupt > property (Rob Herring). > > Changes in v4: > - Add link to bridge chip datasheet (Stephen Boyd) > - Add vpll and vcc regulator supply bindings (Stephen Boyd) > - Add ref clk optional dt binding (Stephen Boyd) > - Add gpio-controller optional dt binding (Stephen Boyd) > > Changes in v5: > - Use clock property to specify the input refclk (Stephen Boyd). > - Update gpio cell and pwm cell numbers (Stephen Boyd). > > Changes in v6: > - Add property to mention the lane mapping scheme and polarity inversion > (Stephen Boyd). > > Changes in v7: > - Detail description of lane mapping scheme dt property (Andrzej > Hajda/ Rob Herring). > - Removed HDP gpio binding, since the bridge uses IRQ signal to > determine HPD, and IRQ property is already documented in binding. > > Changes in v8: > - Removed unnecessary explanation of lane mapping and polarity dt > property, since these are already explained in media/video-interface > dt binidng (Rob Herring). > > Changes in v9: > - Avoid putting re-definition of lane mapping and polarity dt binding > (Rob Herring). > > Changes in v10: > - Use interrupts-extended property instead of interrupts to specify > interrupt line (Andrzej Hajda). > - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda). > > Changes in v11: > - Add a property for suspend gpio function of GPIO1 pin on bridge chip > (Stephen Boyd). > > Signed-off-by: Sandeep Panda <spanda@codeaurora.org> > --- > .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ > 1 file changed, 89 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > new file mode 100644 > index 000000000000..6787f5f2c7cd > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > @@ -0,0 +1,89 @@ > +SN65DSI86 DSI to eDP bridge chip > +-------------------------------- > + > +This is the binding for Texas Instruments SN65DSI86 bridge. > +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > + > +Required properties: > +- compatible: Must be "ti,sn65dsi86" > +- reg: i2c address of the chip, 0x2d as per datasheet > +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) > + > +- vccio-supply: A 1.8V supply that powers up the digital IOs. > +- vpll-supply: A 1.8V supply that powers up the displayport PLL. > +- vcca-supply: A 1.2V supply that powers up the analog circuits. > +- vcc-supply: A 1.2V supply that powers up the digital core. > + > +Optional properties: > +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. > + > +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing > + > +- gpio-controller: Marks the device has a GPIO controller. > +- #gpio-cells : Should be two. The first cell is the pin number and > + the second cell is used to specify flags. > + See ../../gpio/gpio.txt for more information. > +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of > + the cell formats. > + > +- clock-names: should be "refclk" > +- clocks: Specification for input reference clock. The reference > + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > + > +- data-lanes: See ../../media/video-interface.txt > +- lane-polarities: See ../../media/video-interface.txt These two properties are still ambiguous - the bridge has two ports, what port they describe? Regards Andrzej > + > +- suspend-gpios: OF device-tree specification for GPIO1 pin on bridge (active low) > + > +Required nodes: > +This device has two video ports. Their connections are modelled using the > +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. > + > +- Video port 0 for DSI input > +- Video port 1 for eDP output > + > +Example > +------- > + > +edp-bridge@2d { > + compatible = "ti,sn65dsi86"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x2d>; > + > + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; > + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; > + > + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; > + > + vccio-supply = <&pm8916_l17>; > + vcca-supply = <&pm8916_l6>; > + vpll-supply = <&pm8916_l17>; > + vcc-supply = <&pm8916_l6>; > + > + clock-names = "refclk"; > + clocks = <&input_refclk>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + edp_bridge_in: endpoint { > + remote-endpoint = <&dsi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + edp_bridge_out: endpoint { > + data-lanes = <2 1 3 0>; > + lane-polarities = <0 1 0 1>; > + remote-endpoint = <&edp_panel_in>; > + }; > + }; > + }; > +}
On 27.06.2018 11:57, Sandeep Panda wrote: > Document the bindings used for the sn65dsi86 DSI to eDP bridge. > > Changes in v1: > - Rephrase the dt-binding descriptions to be more inline with existing > bindings (Andrzej Hajda). > - Add missing dt-binding that are parsed by corresponding driver > (Andrzej Hajda). > > Changes in v2: > - Remove edp panel specific dt-binding entries. Only keep bridge > specific entries (Sean Paul). > - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). > - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). > > Changes in v3: > - Remove irq-gpio dt entry and instead populate is an interrupt > property (Rob Herring). > > Changes in v4: > - Add link to bridge chip datasheet (Stephen Boyd) > - Add vpll and vcc regulator supply bindings (Stephen Boyd) > - Add ref clk optional dt binding (Stephen Boyd) > - Add gpio-controller optional dt binding (Stephen Boyd) > > Changes in v5: > - Use clock property to specify the input refclk (Stephen Boyd). > - Update gpio cell and pwm cell numbers (Stephen Boyd). > > Changes in v6: > - Add property to mention the lane mapping scheme and polarity inversion > (Stephen Boyd). > > Changes in v7: > - Detail description of lane mapping scheme dt property (Andrzej > Hajda/ Rob Herring). > - Removed HDP gpio binding, since the bridge uses IRQ signal to > determine HPD, and IRQ property is already documented in binding. > > Changes in v8: > - Removed unnecessary explanation of lane mapping and polarity dt > property, since these are already explained in media/video-interface > dt binidng (Rob Herring). > > Changes in v9: > - Avoid putting re-definition of lane mapping and polarity dt binding > (Rob Herring). > > Changes in v10: > - Use interrupts-extended property instead of interrupts to specify > interrupt line (Andrzej Hajda). > - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda). > > Changes in v11: > - Add a property for suspend gpio function of GPIO1 pin on bridge chip > (Stephen Boyd). > > Signed-off-by: Sandeep Panda <spanda@codeaurora.org> > --- > .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ > 1 file changed, 89 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > new file mode 100644 > index 000000000000..6787f5f2c7cd > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > @@ -0,0 +1,89 @@ > +SN65DSI86 DSI to eDP bridge chip > +-------------------------------- > + > +This is the binding for Texas Instruments SN65DSI86 bridge. > +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > + > +Required properties: > +- compatible: Must be "ti,sn65dsi86" > +- reg: i2c address of the chip, 0x2d as per datasheet > +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) > + > +- vccio-supply: A 1.8V supply that powers up the digital IOs. > +- vpll-supply: A 1.8V supply that powers up the displayport PLL. > +- vcca-supply: A 1.2V supply that powers up the analog circuits. > +- vcc-supply: A 1.2V supply that powers up the digital core. > + > +Optional properties: > +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. > + > +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing One more thing, I have overlooked: why do you need this property? eDP panels passes its EDID via DP-AUX channel, do you have some strange panel? I have looked for the panel you want to add in this patchset - "Innolux TV123WAM" and found nothing, there is TV123WAM made by BOE (it is the same panel??) and it reports EDID via DP-AUX, no I2C lines for DDC. Regards Andrzej > + > +- gpio-controller: Marks the device has a GPIO controller. > +- #gpio-cells : Should be two. The first cell is the pin number and > + the second cell is used to specify flags. > + See ../../gpio/gpio.txt for more information. > +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of > + the cell formats. > + > +- clock-names: should be "refclk" > +- clocks: Specification for input reference clock. The reference > + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > + > +- data-lanes: See ../../media/video-interface.txt > +- lane-polarities: See ../../media/video-interface.txt > + > +- suspend-gpios: OF device-tree specification for GPIO1 pin on bridge (active low) > + > +Required nodes: > +This device has two video ports. Their connections are modelled using the > +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. > + > +- Video port 0 for DSI input > +- Video port 1 for eDP output > + > +Example > +------- > + > +edp-bridge@2d { > + compatible = "ti,sn65dsi86"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x2d>; > + > + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; > + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; > + > + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; > + > + vccio-supply = <&pm8916_l17>; > + vcca-supply = <&pm8916_l6>; > + vpll-supply = <&pm8916_l17>; > + vcc-supply = <&pm8916_l6>; > + > + clock-names = "refclk"; > + clocks = <&input_refclk>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + edp_bridge_in: endpoint { > + remote-endpoint = <&dsi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + edp_bridge_out: endpoint { > + data-lanes = <2 1 3 0>; > + lane-polarities = <0 1 0 1>; > + remote-endpoint = <&edp_panel_in>; > + }; > + }; > + }; > +}
On Wed, Jun 27, 2018 at 03:27:35PM +0530, Sandeep Panda wrote: > Document the bindings used for the sn65dsi86 DSI to eDP bridge. > > Changes in v1: > - Rephrase the dt-binding descriptions to be more inline with existing > bindings (Andrzej Hajda). > - Add missing dt-binding that are parsed by corresponding driver > (Andrzej Hajda). > > Changes in v2: > - Remove edp panel specific dt-binding entries. Only keep bridge > specific entries (Sean Paul). > - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). > - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). > > Changes in v3: > - Remove irq-gpio dt entry and instead populate is an interrupt > property (Rob Herring). > > Changes in v4: > - Add link to bridge chip datasheet (Stephen Boyd) > - Add vpll and vcc regulator supply bindings (Stephen Boyd) > - Add ref clk optional dt binding (Stephen Boyd) > - Add gpio-controller optional dt binding (Stephen Boyd) > > Changes in v5: > - Use clock property to specify the input refclk (Stephen Boyd). > - Update gpio cell and pwm cell numbers (Stephen Boyd). > > Changes in v6: > - Add property to mention the lane mapping scheme and polarity inversion > (Stephen Boyd). > > Changes in v7: > - Detail description of lane mapping scheme dt property (Andrzej > Hajda/ Rob Herring). > - Removed HDP gpio binding, since the bridge uses IRQ signal to > determine HPD, and IRQ property is already documented in binding. > > Changes in v8: > - Removed unnecessary explanation of lane mapping and polarity dt > property, since these are already explained in media/video-interface > dt binidng (Rob Herring). > > Changes in v9: > - Avoid putting re-definition of lane mapping and polarity dt binding > (Rob Herring). > > Changes in v10: > - Use interrupts-extended property instead of interrupts to specify > interrupt line (Andrzej Hajda). > - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda). > > Changes in v11: > - Add a property for suspend gpio function of GPIO1 pin on bridge chip > (Stephen Boyd). > > Signed-off-by: Sandeep Panda <spanda@codeaurora.org> > --- > .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ > 1 file changed, 89 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt Reviewed-by: Rob Herring <robh@kernel.org>
On 2018-06-29 17:31, Andrzej Hajda wrote: > On 27.06.2018 11:57, Sandeep Panda wrote: >> Document the bindings used for the sn65dsi86 DSI to eDP bridge. >> >> Changes in v1: >> - Rephrase the dt-binding descriptions to be more inline with >> existing >> bindings (Andrzej Hajda). >> - Add missing dt-binding that are parsed by corresponding driver >> (Andrzej Hajda). >> >> Changes in v2: >> - Remove edp panel specific dt-binding entries. Only keep bridge >> specific entries (Sean Paul). >> - Remove custom-modes dt entry since its usage is removed from driver >> also (Sean Paul). >> - Remove is-pluggable dt entry since this will not be needed anymore >> (Sean Paul). >> >> Changes in v3: >> - Remove irq-gpio dt entry and instead populate is an interrupt >> property (Rob Herring). >> >> Changes in v4: >> - Add link to bridge chip datasheet (Stephen Boyd) >> - Add vpll and vcc regulator supply bindings (Stephen Boyd) >> - Add ref clk optional dt binding (Stephen Boyd) >> - Add gpio-controller optional dt binding (Stephen Boyd) >> >> Changes in v5: >> - Use clock property to specify the input refclk (Stephen Boyd). >> - Update gpio cell and pwm cell numbers (Stephen Boyd). >> >> Changes in v6: >> - Add property to mention the lane mapping scheme and polarity >> inversion >> (Stephen Boyd). >> >> Changes in v7: >> - Detail description of lane mapping scheme dt property (Andrzej >> Hajda/ Rob Herring). >> - Removed HDP gpio binding, since the bridge uses IRQ signal to >> determine HPD, and IRQ property is already documented in binding. >> >> Changes in v8: >> - Removed unnecessary explanation of lane mapping and polarity dt >> property, since these are already explained in >> media/video-interface >> dt binidng (Rob Herring). >> >> Changes in v9: >> - Avoid putting re-definition of lane mapping and polarity dt binding >> (Rob Herring). >> >> Changes in v10: >> - Use interrupts-extended property instead of interrupts to specify >> interrupt line (Andrzej Hajda). >> - Move data-lanes and lane-polarity property example to proper place >> (Andrzej Hajda). >> >> Changes in v11: >> - Add a property for suspend gpio function of GPIO1 pin on bridge >> chip >> (Stephen Boyd). >> >> Signed-off-by: Sandeep Panda <spanda@codeaurora.org> >> --- >> .../bindings/display/bridge/ti,sn65dsi86.txt | 89 >> ++++++++++++++++++++++ >> 1 file changed, 89 insertions(+) >> create mode 100644 >> Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt >> >> diff --git >> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt >> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt >> new file mode 100644 >> index 000000000000..6787f5f2c7cd >> --- /dev/null >> +++ >> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt >> @@ -0,0 +1,89 @@ >> +SN65DSI86 DSI to eDP bridge chip >> +-------------------------------- >> + >> +This is the binding for Texas Instruments SN65DSI86 bridge. >> +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf >> + >> +Required properties: >> +- compatible: Must be "ti,sn65dsi86" >> +- reg: i2c address of the chip, 0x2d as per datasheet >> +- enable-gpios: OF device-tree gpio specification for bridge_en pin >> (active high) >> + >> +- vccio-supply: A 1.8V supply that powers up the digital IOs. >> +- vpll-supply: A 1.8V supply that powers up the displayport PLL. >> +- vcca-supply: A 1.2V supply that powers up the analog circuits. >> +- vcc-supply: A 1.2V supply that powers up the digital core. >> + >> +Optional properties: >> +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. >> + >> +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID >> probing > > One more thing, I have overlooked: why do you need this property? eDP > panels passes its EDID via DP-AUX channel, do you have some strange > panel? OK i will remove this property in next patchset. I have looked for the panel you want to add in this patchset - > "Innolux TV123WAM" and found nothing, there is TV123WAM made by BOE (it > is the same panel??) and it reports EDID via DP-AUX, no I2C lines for > DDC. > > Regards > Andrzej > >> + >> +- gpio-controller: Marks the device has a GPIO controller. >> +- #gpio-cells : Should be two. The first cell is the pin number >> and >> + the second cell is used to specify flags. >> + See ../../gpio/gpio.txt for more information. >> +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description >> of >> + the cell formats. >> + >> +- clock-names: should be "refclk" >> +- clocks: Specification for input reference clock. The reference >> + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. >> + >> +- data-lanes: See ../../media/video-interface.txt >> +- lane-polarities: See ../../media/video-interface.txt >> + >> +- suspend-gpios: OF device-tree specification for GPIO1 pin on bridge >> (active low) >> + >> +Required nodes: >> +This device has two video ports. Their connections are modelled using >> the >> +OF graph bindings specified in >> Documentation/devicetree/bindings/graph.txt. >> + >> +- Video port 0 for DSI input >> +- Video port 1 for eDP output >> + >> +Example >> +------- >> + >> +edp-bridge@2d { >> + compatible = "ti,sn65dsi86"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <0x2d>; >> + >> + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; >> + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; >> + >> + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; >> + >> + vccio-supply = <&pm8916_l17>; >> + vcca-supply = <&pm8916_l6>; >> + vpll-supply = <&pm8916_l17>; >> + vcc-supply = <&pm8916_l6>; >> + >> + clock-names = "refclk"; >> + clocks = <&input_refclk>; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + edp_bridge_in: endpoint { >> + remote-endpoint = <&dsi_out>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + edp_bridge_out: endpoint { >> + data-lanes = <2 1 3 0>; >> + lane-polarities = <0 1 0 1>; >> + remote-endpoint = <&edp_panel_in>; >> + }; >> + }; >> + }; >> +}
diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt new file mode 100644 index 000000000000..6787f5f2c7cd --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt @@ -0,0 +1,89 @@ +SN65DSI86 DSI to eDP bridge chip +-------------------------------- + +This is the binding for Texas Instruments SN65DSI86 bridge. +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +Required properties: +- compatible: Must be "ti,sn65dsi86" +- reg: i2c address of the chip, 0x2d as per datasheet +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) + +- vccio-supply: A 1.8V supply that powers up the digital IOs. +- vpll-supply: A 1.8V supply that powers up the displayport PLL. +- vcca-supply: A 1.2V supply that powers up the analog circuits. +- vcc-supply: A 1.2V supply that powers up the digital core. + +Optional properties: +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. + +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing + +- gpio-controller: Marks the device has a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../../gpio/gpio.txt for more information. +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of + the cell formats. + +- clock-names: should be "refclk" +- clocks: Specification for input reference clock. The reference + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. + +- data-lanes: See ../../media/video-interface.txt +- lane-polarities: See ../../media/video-interface.txt + +- suspend-gpios: OF device-tree specification for GPIO1 pin on bridge (active low) + +Required nodes: +This device has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DSI input +- Video port 1 for eDP output + +Example +------- + +edp-bridge@2d { + compatible = "ti,sn65dsi86"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2d>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; + + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; + + vccio-supply = <&pm8916_l17>; + vcca-supply = <&pm8916_l6>; + vpll-supply = <&pm8916_l17>; + vcc-supply = <&pm8916_l6>; + + clock-names = "refclk"; + clocks = <&input_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + data-lanes = <2 1 3 0>; + lane-polarities = <0 1 0 1>; + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}
Document the bindings used for the sn65dsi86 DSI to eDP bridge. Changes in v1: - Rephrase the dt-binding descriptions to be more inline with existing bindings (Andrzej Hajda). - Add missing dt-binding that are parsed by corresponding driver (Andrzej Hajda). Changes in v2: - Remove edp panel specific dt-binding entries. Only keep bridge specific entries (Sean Paul). - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). Changes in v3: - Remove irq-gpio dt entry and instead populate is an interrupt property (Rob Herring). Changes in v4: - Add link to bridge chip datasheet (Stephen Boyd) - Add vpll and vcc regulator supply bindings (Stephen Boyd) - Add ref clk optional dt binding (Stephen Boyd) - Add gpio-controller optional dt binding (Stephen Boyd) Changes in v5: - Use clock property to specify the input refclk (Stephen Boyd). - Update gpio cell and pwm cell numbers (Stephen Boyd). Changes in v6: - Add property to mention the lane mapping scheme and polarity inversion (Stephen Boyd). Changes in v7: - Detail description of lane mapping scheme dt property (Andrzej Hajda/ Rob Herring). - Removed HDP gpio binding, since the bridge uses IRQ signal to determine HPD, and IRQ property is already documented in binding. Changes in v8: - Removed unnecessary explanation of lane mapping and polarity dt property, since these are already explained in media/video-interface dt binidng (Rob Herring). Changes in v9: - Avoid putting re-definition of lane mapping and polarity dt binding (Rob Herring). Changes in v10: - Use interrupts-extended property instead of interrupts to specify interrupt line (Andrzej Hajda). - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda). Changes in v11: - Add a property for suspend gpio function of GPIO1 pin on bridge chip (Stephen Boyd). Signed-off-by: Sandeep Panda <spanda@codeaurora.org> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ 1 file changed, 89 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt