@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
new file mode 100644
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,u200", "amlogic,g12a";
+ model = "Amlogic Meson G12A U200 Development Board";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+};
+
new file mode 100644
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "amlogic,g12a";
+
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 3 MiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@5000000 {
+ reg = <0x0 0x05000000 0x0 0x300000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ periphs: periphs@ff634000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xff634000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff634000 0x0 0x2000>;
+ };
+
+ hiubus: bus@ff63c000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xff63c000 0x0 0x1c00>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff63c000 0x0 0x1c00>;
+ };
+
+ aobus: bus@ff800000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xff800000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
+
+ uart_AO: serial@3000 {
+ compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+ reg = <0x0 0x3000 0x0 0x18>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&xtal>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ uart_AO_B: serial@4000 {
+ compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+ reg = <0x0 0x4000 0x0 0x18>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&xtal>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+ };
+
+ gic: interrupt-controller@ffc01000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xffc01000 0 0x1000>,
+ <0x0 0xffc02000 0 0x2000>,
+ <0x0 0xffc04000 0 0x2000>,
+ <0x0 0xffc06000 0 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ cbus: bus@ffd00000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xffd00000 0x0 0x25000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x25000>;
+ };
+
+ apb: apb@ffe00000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xffe00000 0x0 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x200000>;
+ };
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+};
Try to add basic DT support for the Amlogic's Meson-G12A S905D2 SoC, which describe components as follows: Reserve Memory, CPU, GIC, IRQ, Timer, UART. It's capable of booting up into the serial console. Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts | 22 +++ arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 172 ++++++++++++++++++++++++ 3 files changed, 195 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a.dtsi